Certainly today, if Entrance door has lost its former attractiveness, the issue can be solved radically - just replace it. Fortunately, those times have passed when this procedure was really a problem due to the total shortage of absolutely everything. But… First of all, not everyone wants to part with their good, albeit already dried up and let in all sounds and smells door. Secondly, not everyone can afford the installation of a new one. What to do in this case? Breathe a second life into it - upholster the door with dermantine! With your own hands or invite a specialist. True, the first option is preferable, if only because it will allow you to save a fairly significant amount. And this, you see, is a strong argument. Therefore, arm yourself with materials, tools and knowledge on how to upholster a door with dermantine. And don't be scared. Even if you have held a hammer in your hands only a couple of times in your entire life, everything will work out! The process is very simple, you will not have any difficulties.
So let's start. We offer you a master class on the topic: "How to upholster a door with dermantine." Study, and then, with full confidence in your abilities, proceed to work.
All about dermantin
But first you need to say a few words about the upholstery material itself, which, by the way, has been updating doors for a very long time. It is considered a type of artificial leather, but it is a more budgetary version of it. The wrong side of it is and the front side is a layer of nitrocellulose.
If we talk about him performance characteristics, it should be noted that leatherette is distinguished by strength, durability, ease of care, more than affordable cost. In addition, there is such a variety of colors and textures on sale that if you decide to upholster the door with dermantine with your own hands, you will not have any problems with the choice. On the contrary, one can choose interesting option of this material, your front door will look as good, if not better, than your neighbor's expensive, custom-made door.
What you need
Agreed with the upholstery. But since it is necessary to upholster the door with dermantine using a heater - a special lining material, then you need to stock up on them. Usually, either foam rubber or special batting is used for these purposes. As for the amount of material needed, both insulation and leatherette should be purchased according to the size of your door (including allowances for seams - ten to twelve centimeters on each side).
You will also need furniture nails. They are usually produced with metal hats, which can be made in various colors and stylized as silver, gold or bronze. If desired, you can also find carnations, in which the hats are upholstered with dermantine. Still to be purchased metal corners(four pieces), PVA glue.
How to upholster a door with dermantine without a tool? No way! Therefore, stock up on a screwdriver, screwdriver, hammer, stapler and scissors. You can start.
Preparatory stage
The door, of course, will have to be removed from its hinges. Then remove from it - if any - all the old upholstery. Along the way, get rid of everything that can interfere with the update process: remove the lock, remove the peephole, hinges. If there are any defects on the door leaf - eliminate them. When the surface is fully prepared, you can proceed to the main stage.
How to upholster a door with dermantine
Free up space in a room or hallway, put two stools, put a door on them. Screw on the corners. They will make your structure stronger. Cut the insulation in accordance with glue and glue the foam rubber or batting. In order not to wait until the glue dries, grab the material in several places with a stapler. Then lay out a piece of leatherette on the insulation, and so that there are identical seam allowances on each side. And then tuck the edges inward, under the insulation, forming, as it were, a small roller and at the same time nailing them. Algorithm of actions: we start from the top edge, then we fix the left and right sides, the bottom - at the very end. When fixing the roller, be sure to ensure that its thickness is uniform. And be sure to drive in the carnations at the same distance from each other, otherwise your door is unlikely to look neat.
That, perhaps, is all. On this master class "How to upholster wooden door dermantin" can be considered complete. But still, it is necessary to mention one small detail, thanks to which the front door to your apartment will become truly exclusive.
decorative trim
To decorate the surface of the updated door, you can use special braid or cords. Of these, a drawing is laid out in the center or over the entire surface, and then fixed in the right places with carnations. And you can “depict” whatever your heart desires: a grid, vignettes, rhombuses. It's like fantasy tells you.
Now that's really all. It is possible not only with clear conscience to teach everyone how to properly upholster a door with dermantine, but also to demonstrate the result.
No matter how trite it may sound, but the front door is the face of the house! It not only performs practical functions, but also allows guests to get an impression of your home. Of course, the desire to sheathe the front door arises, as a rule, when it thermal insulation properties leave much to be desired. However, if you make such a repair well, you can transform the old door structure with your own hands that doorway get a new, unique look.
Where to begin?
First you need to take a tape measure and measure the opening. First of all, you need to measure the height of the door. To determine the width, measure the distance between the points of contact between the door and the frame. The depth of the door will be the width of the corners, it can also be determined using ordinary plasticine, a piece of which must be placed between the door leaf and the box. By closing the door, you will receive an impression that is easy to measure. The received data must be recorded, according to them in the store they will help you calculate required amount material. It is better to prepare the opening in advance by dismantling the old skin with your own hands, removing the lock and other fittings.
What will be needed?
The turn has come to take care of the materials, given their features:
Instruments
Wooden and metal doors are finished a little differently, it also matters which side of the door (outside or inside) is to be finished. However, having bought upholstery materials at a hardware store, do not forget to stock up on auxiliary tools and accessories, without which repairs are impossible. Their approximate list looks like this:
- corners;
- Decorative strips;
- self-tapping screws;
- Staples;
- Furniture nails (including decorative);
- Styrofoam;
- bars;
- Glue (in the absence of special glue, the “universal moment” is quite suitable);
- Brush for applying glue;
- Scissors;
- Construction stapler;
- A hammer;
- Stationery knife.
Working process
AT in general terms do-it-yourself upholstery repair is as follows: internal cavity doors around the perimeter and in the center have wooden beam which is fastened with screws. Further actions depends on the type of upholstery chosen. The material is attracted to the inside outer side with the help of long self-tapping screws, for upholstery of the outer side of the door, self-tapping screws are mounted from the inside along the perimeter of the door leaf.
Repair and sheathing with thin-sheet material, such as fiberboard, has its own nuances - the sheets are simply glued in the middle, and along the perimeter of the canvas they are attached and covered with decorative strips to beautifully disguise the fasteners. Thus, the doorway turns out to be very neat even with your own hands.
To upholster the door with leatherette with your own hands, you need to measure the opening and cut out the appropriate size of the insulation. You can fasten it with metal staples, furniture nails, and in some places - with glue. Repair and replacement of upholstery is carried out, as a rule, with the help of decorative carnations. The edges of the material are bent and well fixed.
Sheathing with "clapboard" or wooden lath is another interesting option for door upholstery. The “lining” is impregnated with various compounds that give it the qualities of fire resistance, prevent its decay and increase moisture resistance. This finish is not inferior in practicality to PVC, but surpasses it in environmental friendliness. "Clapboard" can be painted or varnished, and it is not at all difficult to mount. Therefore, this door trim is suitable not only for an apartment, but also decorates the opening in a private house.
Wooden door trim
The upholstery of wooden entrance doors involves the manufacture and fastening from the inside around the perimeter of the door leaf of a special roller that closes the gaps between the leaf and the frame. Such a roller is made of upholstery material and insulation: the materials must be cut along the height and width of the door, attached and fixed with a stapler so that insulation strips are obtained along the entire contour of the door.
metal door trim
An iron door can be insulated with beams, making a frame out of them around the perimeter of the door using self-tapping screws. Holes for mounting panels must be made in accordance with the selected panels - they have instructions that describe the features of their fastening. Holes for the eye, handle and lock are calculated and cut out independently. The insulation is inserted into the niches between the bars and fixed with glue. The repair will be completed by gluing a decorative corner on the iron door around the perimeter - it will close the edges of the panels.
Thus, if the door has lost its functional properties or appearance, do not rush to resort to replacing it, because knocking off an inexpensive iron or old wooden front door is quite realistic, and anyone can increase its service life with their own hands.
The front door, not decorated with upholstery or having an old cracked surface, looks extremely sloppy, in advance forming a negative image of the homeowners among those who came. Moreover, it does not retain heat inside the apartment, and all the noise from the entrance freely penetrates into the premises. Therefore, over time, any good owner has a desire to tidy up both from the aesthetic and from the practical side.
Upholstering a door with leather with your own hands, while also solving the issues of insulation and soundproofing, is quite possible, since this event does not belong to works of a high degree of complexity, and is available to almost everyone. The main thing is to have everything necessary materials, certain tools and a good understanding of the sequence of work.
1. To update the door upholstery, you will need to prepare the following materials:
- Genuine leather, of course, is a very expensive material, and is used for these purposes in exceptional cases. It does not matter, there is artificial leather (leatherette or leatherette). This material is available in a wide range of construction stores, and vary in color, thickness and texture pattern, so you can choose it for every taste. High-quality artificial leather both visually and tactilely differs little from natural.
The width of this material varies from 1100 to 1400 mm, and this is quite enough for the size of any door leaf. Before purchasing leatherette, you need to measure the height of the door and add 25-30 cm to the result. This length of upholstery should be bought for one side.
Also, one must not forget that upholstery will be needed for the manufacture of rollers that will be fixed around the perimeter of the door leaf. For them, you will need three strips, having a width of 12-15 cm and a length that is equal to the height of the door.
- For soundproofing and insulation, sheet foam rubber, dense synthetic winterizer or felt are suitable. The required material thickness is from 10 to 25 mm.
As a heater, you can use felt ...
This value will depend both on the type of material and on the desired volume of the pattern, if it is supposed to be done using decorative nails, thin wire or fishing line.
... or foam sheets
- Wallpaper nails with a decorative cap. They can be made from copper, silver or gold tone alloys, or they can be covered in the same color material as the upholstery chosen.
Wallpaper carnations - you can choose the most suitable design
The diameter of the hats or their design will depend on design solution on the design of the door leaf.
To general view d veri looked harmonious, it is best to match the nails to the color of the door handle and lock.
- If a metal door is put in order, then one of the highly resistant polymer adhesives is purchased for this, for example, "88" or the universal "Moment".
- In addition to sheet insulation material, you will need strips of round insulation (foam rubber or polyethylene foam), sold by the footage. For our purposes, a diameter of 10, 15 or 20 mm is suitable.
2. From the tools should be prepared:
- Staples and stapler for temporary fixation of insulation and upholstery. Most convenient size staples for door upholstery 8÷10 mm.
- Medium-sized hammer for driving decorative nails.
- Spicy construction knife- it is useful for cutting insulation and upholstery material.
- A screwdriver with a set of nozzles (bits) and a massive screwdriver - they are useful for dismantling the old casing, removing and then installing locks and a viewing eye.
- A nail puller and pliers are needed to pull out nails, if they will go wrong when driving in and, necessarily, to carry out the dismantling of the old coating, in the case when it was installed.
- Scissors for cutting materials.
3. K preparatory work can be attributed to the removal old upholstery doors:
- First, all removable elements - peephole, locks and door handles.
- Next, with the help of tools, the old skin is removed as accurately as possible. It can be picked up with a powerful screwdriver, and then with pliers. Usually, if the materials are not planted on glue, leatherette and insulation are separated from the door leaf quite easily. When removing the upholstery from an old wooden door, do not use excessive force so as not to damage the canvas. Be sure to carefully inspect the entire surface to remove the remaining unnecessary nails, staples, screws, fragments of the old coating
- After cleaning the surface, the door can be removed from the hinges and laid on a prepared desktop (workbench) or four to six stools installed. Further upholstery work can be carried out in this position. If it is decided to remove the canvas from the hinges, then before this process it is necessary to mark its contour on the door frame.
- Sometimes the door is not removed, and its lining is carried out in a suspended state in its regular place.
How to upholster a door with leather with your own hands - various options
To disassemble the entire technology for sheathing from all sides in detail, you need to consider three different options work is upholstery outside wooden door, then internal, and then dwell on the features of a similar process on metal door.
Wooden door - interior upholstery
According to a long-established practice, wooden entrance doors in high-rise buildings opened into the apartment. This is the option that will be considered.
The inner lining of the door that opens into the apartment is somewhat different from the outer upholstery, and the main difference in this process is the use of additional insulation elements - rollers. They are made from upholstery strips and chopped insulation. It is convenient to use ready-made polyethylene foam rollers, which are sold by the meter, as an insulating gasket. This element general design serves to securely close the gaps between the door leaf and the door frame. Therefore, they are nailed in such a way that they protrude beyond the door by 10 ÷ 20 mm. It must be remembered that on the side where the hinges are located, the roller is fastened in such a way that it completely covers the gap along the entire height of the door jamb.
- The first stage of work is cutting upholstery and insulation. For the first, the exact geometric parameters of the door are taken, to which 120-150 mm are added - this will become the size that will be needed for the decorative sheathing of the canvas.
As a rule, there are always strips of scraps left - they are excellent for forming sealing beads for contour upholstery.
The insulation sheet should be 10 mm smaller on each side than the door itself.
- Along the perimeter of the door, strips of leatherette are fastened with staples with a stapler, face down. Usually, strips up to 140 mm wide are used, the length is exactly the size of the door tight. At the same time, about 40 mm of this strip is placed on the surface of the door - the rest should be outside.
Insulation tapes of polyethylene foam rubber are wrapped in these strips. Thus, rollers are formed, which are also, with a stapler, fixed on the door leaf.
Installation of rollers begins from the upper right corner of the door, then they are fixed by the vertical edges of the door, and only then - to the bottom. This takes into account the location of the door relative to the floor - the roller should not rub against flooring, since this will wear out and tear very quickly.
If it is intended to install a consignment note, then this is taken into account when attaching the rollers - an appropriate gap is made.
- Next, on door leaf fit insulation material. It is fixed around the perimeter with the help of brackets, stepping back from its edge by 5-7 cm. Holes for the viewing eye and locks are immediately cut out in it.
- The next step is fixing on the surface, on top of the insulation, the upholstery material itself - artificial leather.
It wraps around the edges of the insulation and is fixed at the upper corners with staples. If the upholstery is planned with a special pattern, then its marking is carried out on the material fixed on top.
If the leather substitute must be fixed only along the perimeter, then decorative nails are hammered at the same distance from each other in 60 ÷ 80 mm. The material is stretched in the course of nailing, since after completion of work it must be perfectly even.
Find out the top 10 door options from our new article -
Upholstery on the outside of a wooden door
The outer upholstery of the door opening inside the apartment is as follows:
- Previously, when closed, a rectangle is outlined with a pencil on the door leaf door frame- this line will show how far from the edge the upholstery should be installed. The remaining distance will be needed for the "quarter" selected in the door jamb.
- The next step is to fix the insulation material with a deviation from the drawn line inward by one centimeter.
- Then the main skin material is nailed to the door along the outlined line with bend its edge in inside, similarly internal installation, but the bottom edge of the material is left free for now.
A characteristic feature is that the sealing rollers are not attached to the door leaf, but to the frame
- From the outside, the insulating roller is installed on three sides not on the door, but on the racks and the crossbar of the door jamb, except for the bottom side. Nailing such a roller to the threshold is absolutely pointless, since it will not perform its functions, moreover, it will quickly come off or be erased from constant contact with the shoes of people passing through the door.
Leatherette strip is fixed front side to the jamb with a stapler, a strip of insulation is installed in it, the second side of the material is tucked inward, forming a roller, and nailed with decorative nails. The roller should be on the door when it is closed by 15 - 20 mm, but you need to make sure that it does not fall on the keyhole.
- The lower insulation roller cannot be too voluminous, it is attached to the door leaf itself and must fit snugly against the threshold.
- Further, the main fabric of the upholstery is stretched onto the lower roller and nailed.
- The last step, after upholstering both sides, all door panels are installed. accessories - peephole, handles and locks. It is very important to carefully make small cuts on the skin. The main thing is not to cut the material more than is required, otherwise the door will immediately lose its respectable appearance.
Video: Wooden front door upholstery option
Features of working on a metal door
It is usually installed as an external one, always opening outwards. It will also be nice to insulate it from the inside and transform it on both sides.
Outer side
Transforming and insulating a metal door, do not use insulating rollers around the perimeter. This door has a completely different purpose - it is used as the main protection of the entrance to the home and ill-wishers, and only then - as additional protection by cold.
Installation of upholstery and insulation on metal from the outside is carried out with glue. The insulation in this case is cut out 10 ÷ 15 mm smaller than the door leaf, both in length and width. The upholstery material should exceed its size by 50-60 mm - this part of the material will go to the bend around the metal shelves of the door leaf.
- On the metal surface, stepping back from the edge of 10 ÷ 15 mm, and in several places in the middle of the plane, glue is applied in strips.
- Then a heater is laid on it and is well pressed against the door leaf. It is necessary to give time to the glue under the heater to dry. The specific period will be indicated in the instructions for use of a particular composition.
- Next, you can start gluing the leatherette. Glue is applied to the back of the metal plate from the top of the door, at a distance of 50 mm. He needs to give a few minutes to grasp.
- Then, noting the middle of the width of the door and the sheathing material, it must be applied to the glued place according to the marks and carefully pressed, and then give some time for a good grip.
- The next step is to glue the side parts of the door in the same way - the sheathing material is bent and glued onto the shelves. If, when pulled, an excess of leatherette has formed, even a few millimeters, it must be cut off sharp knife, otherwise it will interfere with the closing of the door. If the sheathing material is dense enough, then you may have to cut off the corners so that the close-fitting is as accurate as possible.
Inner side
If the inner side of the metal door is not insulated, then you should think about this event. Usually, on the reverse side, a metal door looks like a frame welded from corners and a profile pipe, on which it is welded a metal sheet acting as a door leaf. It's already wrapped in faux leather.
Now you need to insulate and finish the inside of the door.
- In this case, polystyrene foam, which has the thickness of the door frame, is perfect for insulation.
- You will also need wooden slats of the same thickness.
- To seal the joints and seams, mounting foam is required.
- It is necessary to prepare a drill with a drill for metal screws.
- For interior decoration thin plywood, soft insulation and leatherette can be used.
- The first step is to fix the wooden planks to the frame. To do this, in the corners or profile pipe drill holes and fix the strips to them with self-tapping screws. Reiki are necessary so that it is convenient to attach plywood or other inner lining to them.
- To remove the "cold bridges", between the possible gaps between the metal and the slats fill mounting foam. By the way, it will give additional rigidity to the fastening of the rails, as it also has pronounced adhesive properties.
- After the slats are screwed and treated with foam, polystyrene foam panels are installed between them. The gaps between them and the rails are also carefully filled with mounting foam.
- While the foam dries, you can start preparing plywood sheet. Its thickness must be chosen in such a way that the door is easily pressed against the jamb, especially since insulation and sheathing will still be installed on it.
- The plywood blank should have the size of the inside of the door, insulated with foam, plus the width of the frame along the upper and lower sides of the perimeter of the door leaf.
- A thin insulation is glued over the entire area of \u200b\u200bplywood.
- Further, the plane is completely tightened with leatherette, with its bend to the inside. The material is fixed with glue and additionally fixed in several places with brackets.
- When the panel is completely ready, the location is marked on it. wooden slats screwed to metal frame. This process must be done very carefully so that barely noticeable points remain on the skin, along which decorative nails will be hammered.
- It is possible that you will have to make another hole in the corners and fix the corners of the plywood sheathing with self-tapping screws to ensure that this lining fits snugly against the metal frame.
Video: Upholstery of a metal door with its insulation
It should be noted that, if desired, the plywood lining can be replaced ordinary clapboard from natural wood or laminated fiberboard. It, starting from the bottom, is attached to the same installed rails.
Upholstering the door with leather or is not difficult at all. By doing this work yourself, the landlord can save quite a large amount. To facilitate the calculations and the upholstery process can purchase ready kit, which includes a set of materials designed to decorate a standard door.
Video - How to upholster a door with leatherette
If an old wooden door in a house or apartment has lost its former appearance over time, you should not replace it with a new one: old design can be restored. And besides, new wooden door systems are too expensive, and beautiful designs created from chipboard or MDF are short-lived.
Competently restored wooden structures look amazing. Refresh door system it is not difficult to do it yourself, and such a procedure takes a little time.
In this case, painting the doors alone is not enough: this event is more of a cosmetic nature, so more drastic measures are needed.
Sheathe wooden structure with your own hands you can use the following material:
- laminate;
- plastic;
- clapboard;
- dermantine.
Laminate is made from fibreboard. This material is finishing boards(their average thickness is 7-8 mm). Wrong side finishing material- waterproof paper. Currently, laminate is produced in the most variety of options: imitation of stone, wood, ceramic effect, etc.
Thanks to such a variety of proposals, you can update the door for any interior. Moreover, laminate is not just a decor, it is also a wonderful heat and sound insulating raw material. But since this sheathing material is hygroscopic, it is used only for inner plating(It is not suitable for finishing the canvas on the outside).
Lining is considered an excellent option. This upholstery material is a wooden slats, equipped with special grooves, which facilitates the process of their fastening. The thickness of the lining ranges from 6 mm to 2 cm.
In the manufacture of this sheathing material, it is treated with antiseptic agents. And although the lining is less hygroscopic than laminate, it is still not recommended to sheathe the front door from the outside with it: this decor is best used for interior structures or the inside of the input block. In addition, it should be noted that the lining is an excellent noise and heat barrier.
MDF is obtained from pressed granular chips. The thickness of the plates with which the door leaf can be sheathed is 16 mm. These panels are covered with a PVC film at the production stage, thanks to which they are resistant to the damaging effects of moisture and mechanical damage. In view of this, MDF can be used for door trim from the outside.
Plastic - decor created from polyvinyl chloride with the addition of special chemical substances, increasing the resistance of the material to extreme temperatures, exposure to ultraviolet radiation and moisture. This upholstery material is easy to install and does not require special care.
However, he has an “Achilles heel”: plastic is characterized by low strength. Therefore, to use it for sheathing only the inside of the structure or to sheathe the front door with it inside and out, they decide in each case individually.
If it is decided to update the doors in the house with dermantine, experts recommend paying attention to a leather substitute made on the basis of synthetic fabric.
This decor has a considerable list of advantages:
- elastic (stretches easily);
- waterproof;
- does not crack under the influence of low temperatures;
- lasting.
In addition, dermantine can update both the outer and inner side of the front door. As a lining when upholstered with dermantin, a synthetic winterizer, batting or polyurethane foam (the most the best option, according to experts, is polyurethane foam).
Thanks to the wide range of colors currently produced leatherette, almost any buyer can choose upholstery material to his taste and color. Thus, the upholstery made with dermantine will fully meet the tastes of the owner of an apartment or a country house.
Pigtail recovery
An okosyachka or casing is a wooden box installed around the perimeter of an opening (door or window) in wooden house. Before updating this structural element with your own hands, it is worth getting to know its purpose better.
Firstly, the pigtail prevents windows and doors from being crushed. The fact is that during shrinkage wooden walls the logs are very “twisting”, as a result of which they can slightly shift and put pressure on a window or doorway. Casing minimizes this load, protecting structures from crushing. In fact, a correctly made do-it-yourself pigtail or casing in a house is a guarantee that the windows and doors installed in this building will last for many years.
Secondly, the pigtail strengthens the stability of the walls and, as a result, makes the house more durable. Therefore, casing is recommended even in log houses built more than two years ago.
Thirdly, a pigtail is an appropriate decor. If the casing has an interesting texture and is covered with a well-chosen colors, it can become an important decorating element of the structure.
You can update this decor with your own hands by painting it or covering it with another chemical composition intended for processing wooden elements designs. However, you need to process the box carefully: this forms a protective “casing” for the structure from moisture and other atmospheric influences, and also creates an impeccable decor.
Insofar as modern market offers treatment compounds for casing different shades, you can update the wooden box with your own hands by painting it in any of them.
However, it is worth paying attention to the fact that the pigtail is not sheathed or upholstered with dermantine, clapboard, laminate or other material. But if it is properly processed, the pigtail will become a durable, beautiful and reliable element of the house. However, the front door restored with your own hands is no less important: it can become an appropriate business card of the house and its reliable “guard”.
Entrance and interior doors lose their attractiveness over time, but it is not always reasonable to purchase a new canvas, in most cases a new leatherette upholstery can save the situation. At the same time, such an event improves the heat / sound insulation properties of the door, which is especially important for residents of multi-storey buildings.
Leatherette (also called leatherette, eco-leather or granitol) as a material was known and popular to our forefathers in the 30-40s of the 20th century. Leatherette was used to upholster not only doors, but also furniture, as well as book bindings and much more. However, at that time the quality of the material was at a mediocre level, and the variety color palette and textures left much to be desired.
Now, thanks to modern developments, leatherette has become a strong, attractive in appearance and durable material with a wide palette of shades and textures. Leatherette is one of the many leather substitutes. During the production process, nitrocellulose, polyurethane or vinyl coatings are applied to the base-fabric on one / two sides, which ensure the external resemblance of the finished material to natural counterparts.
Reasons for the popularity of leatherette
- Leatherette endures temperature changes.
- The material "breathes", but at the same time it has water-repellent properties.
- Leatherette is quite durable, has sufficient tensile strength, the surface is difficult to damage.
- Leatherette is easy to care for. With a frequency of several months, the surface should only be covered with impregnation. Pollution is eliminated with soap suds, ammonia or ordinary medical alcohol.
- Eco-leather is attractive in appearance and is very different affordable price. Anyone who knows how to hold a hammer in their hands can buy a piece of material and beat the door with their own hands.
- Leatherette as upholstery is a good sound and heat insulator, respectively, if you upholster the door with eco-leather, then the room will become much more comfortable.
When choosing a material for door upholstery, pay close attention to the thickness of the base fabric and the quality of the coating. It is advisable to choose a dense material that slightly springs when stretched. High-quality leatherette does not have stains from paint, and if you run a fingernail over the surface, then there are no traces left. Don't forget about the smell. The harsh chemical amber does not fade over time and will be constantly felt in the room.
If the quality of the material suits you, all that remains is to make a purchase by paying for a piece of leatherette, the length and width of which is approximately 10-15% larger than the dimensions of the door.
What will be useful for work?
Leatherette will have to be cut, which means you will need scissors, pencil and meter ruler or tape measure.
To fix a piece of material, it will come in handy construction stapler, hammer, building and furniture decorative nails(metal or covered in matching color vinyl leather). for sheathing iron door nails are not needed. They will be replaced by mounting glue.
Additionally, for decoration, you can prepare decorative wire or cord. If the door is very old, it is recommended to purchase metal corners to further strengthen the structure.
If planned additional insulation then it is worth buying foam rubber, felt or batting.
And to prepare the door for sheathing, you need pliers, screwdriver, pliers.
The purpose of the preparation is to get a smooth door leaf, on which leatherette will lie beautifully and evenly. Therefore, it is necessary to remove the peephole, dismantle door handle, lock, remove old skin, if there was one.
It is important to eliminate all protruding and protruding parts. If the door is embossed, then a sheet will help to quickly align it. thin plywood, cut according to the dimensions of the door and nailed around the perimeter with construction nails.
This option is suitable for interior doors. Work will be much more convenient if the door is removed from its hinges and laid horizontally on a pair of stools of the same height.
Step one. We prepare materials
In addition to the list of materials and tools listed above, you will need frame profiles for fabric tension (one-sided). It is these profiles that we cut so that you can easily place them around the perimeter of the door.
And you will also need furniture buttons, consisting of two parts - metal base with carvings and hats covered with leatherette.
Step two. Making markup
In order to evenly and beautifully sheathe the door with leatherette, we make markings, namely:
- using a square and a tape measure, we divide the door with two perpendicular lines into four equal parts;
- We mark on the door the places where the buttons will be installed.
Step three. We fasten buttons, insulation and trim
On those places where the buttons will be located, we apply assembly glue. We glue the details of the buttons with threads.
We take the already cut profiles and glue them around the perimeter of the door. We wait until the glue dries (about a day).
In the meantime, the glue dries, in a sheet of insulation (polyurethane foam or foam rubber) we cut holes for buttons. The next day, we spread the insulation on the surface of the door, combine the holes in the material with the button fasteners glued to the door. Trim off the excess around the edges. We do the same with dermatin. It remains only to fasten the buttons, pull on the leatherette and tuck it into the profiles.
Step four. Final
We install the handle and hang the door in place. This completes the work.
Upholstering the door with dermantine with your own hands is easy! Classic variant
The work is quite painstaking, but everyone can do it. It is not necessary to remove the door from the hinges.
We cut out the material. We will need strips of leatherette about 15 cm wide for bordering rollers and a layer of material a little larger than a door.
We take leatherette strips, carnations and a hammer. We place the strip with the wrong side up. With carnations (step - 10 cm) or a stapler, we fasten the edge of the strip to the edge of the door.
Using a stapler or glue, we fix foam rubber on the surface of the door. Cut off the excess with a utility knife. On top of the foam rubber, we attach two layers of batting in the same way. This will extend the life of the short-lived foam rubber and improve the thermal insulation qualities of the door.
Let's start attaching leatherette fabric. We hammer the first decorative carnation at the top of the door, in the middle. The second is from the bottom in the center of the door. This will avoid distortion. For the same purpose, it is worth pulling the material as tightly as possible. Next, we hammer nails around the perimeter of the door, observing a step of about 10 cm.
We return to the edging of the door. We cut the batting into thin strips, turn each into a tube. We put these tubes in the center of the leatherette strips. We wrap the strips inward so that we get a neat roller. We fix the rollers with decorative carnations.
We fix the handle to the updated door. On this work, you can complete or start decorative trim. To do this, we take a cord, lay out any pattern you like on the door, for example, a zigzag or rhombuses.
Note! If your door opens "from itself", then you will have to mount the rollers not on the door, but on the jambs (box) adjacent to it. On the door itself, the leatherette is simply stretched, the edges are tucked up and fixed around the perimeter with carnations.
Door upholstery with leatherette tile method
The door itself will act as the basis, buttons and foam rubber are also needed. The door must be removed from its hinges.
We make the markup using a square and a meter ruler. We draw the entire door leaf into identical rhombuses, in the corners of which we fasten the base screws for the buttons. We lay out the foam rubber with cut out holes and fix it with a stapler (we insert 3-4 staples around each screw, and also fixing the foam rubber around the chipboard perimeter).
Foam with holes
Cut leatherette into diamonds. Leatherette diamonds should be slightly larger than those marked on the door. Excess material will go to the hem. For leatherette rhombuses, we cut off one corner in advance, so that it is more convenient to make sheathing.
We fasten the first rhombuses along the edges of the door with a stapler, bending. The corners of the rhombuses should be in those places where the fastening for buttons protrudes.
How to fix diamonds in the center of the panel? We lay out the rhombus on the foam rubber according to the markup. The cut corner should be at the top. We fix the lower corner of the rhombus with a bracket. We bend the edges of the material. We fix the right and left corners of the rhombus with brackets, avoiding distortions and wrinkling of leatherette. We fasten the button. We continue until the entire door is hidden behind a neat trim.
Video - Leatherette door trim
Video - Decorative door upholstery