Useful things from plastic pipes with their own hands. Products from PVC pipes do it yourself

August 1, 2016
Specialization: finishing facades, interior decoration, construction of cottages, garages. Experience and gardener and gardener experience. There is also experience in repairing cars and motorcycles. Hobbies: the game is not a guitar and a lot more, to which there is not enough time :)

Plastic pipes are excellent material from which it is possible to collect not only pipelines, but also all sorts of crafts. Moreover, working with them is quite easy and simply, not to mention the fact that this procedure is very exciting. As an example in this article I will give 10 most interesting ideas Use plastic pipes.

Features of making crafts from plastic pipes

Plastic pipes and fittings (corners and tees) in the hands of the wizard turn into the most real designer, from which any framework structures can be collected. The only one needs to pay some attention to the selection of pipes. For example, metalplastic for these purposes is not suitable, so its flexural strength is very small.

Therefore, it is best to use the following types of pipes:

Before sticking the polyvinyl chloride pipe to fitting, you need to remove the chamfer to get rid of the burrs, which in the process of connecting parts can shrore glue.

Options Homemade

Option 1: Stand for a laptop

Let's start with the simplest, but, however, a very useful product - a laptop stand. In the photo below, we see how to make a support from PVC pipes.

So, the instructions for its manufacture are quite simple:

1. first of all, measure your laptop so that the stand is perfect for it;
2. then cut the tubes according to the resulting dimensions:

• 2 tubes must be about 5 cm long laptop depth;
• 1 tube must be 2-3 cm shorter laptop width;
• 2 short tubes - from their length depends the height of the rise of the stand;

1. now to two long tubes, glue the corners and connect them with short tubes, as a result of which 2 g-shaped parts should be obtained;
2. after that, glue the corners to short tubes and connect the parts of the longest tube, which should be perpendicular;
3. next to the two ends of M-shaped parts, glue the corners that will serve as limiters so that the laptop does not drive from the stand;
4. at the end of work, the product can be painted in any color of the color of aerosol paint.

Now it will be more convenient to work with a laptop, besides, you can put it on the bed or sofa, and it will not overheat.

Option 2: Sledge for children

Scoops from plastic pipes are a more complex design, however, they are made practically by the same scheme as the stand for a laptop. therefore certain with the task will be able to every craftsman.

For the manufacture of the sled you will need the following materials:

• two pipes with a diameter of 40 mm;
• tips for pipes 40 mm;
• pipes with a diameter of 25 mm;
• tees and corners under 90 and 45 degrees for pipes with a diameter of 25 mm.

Sani are manufactured as follows:

1. start work with the preparation of the drawing. Based on the design, use any sleeves in the photo above. The main task of the drawing is to designate the dimensions of all parts that it will simplify and speed further work.;
2. next, make a force from the pipes of fortification. To do this, mark the places of their bending with a pencil and warm up on open firerotating the pipe along the axis. When the plastic softens, the ends should be beatened so that the polls easily slide through the snow and did not break.
   Bending a force is preferably not only in front, but also from behind. After that, on ready-made pollings you need to wear a plug;
3. now you need to assemble the top of the sleigh, i.e. The framework to which the seat will be attached. The frame must have a rack for connecting to the clauses.
   This design is a rectangle with rigid ribs in the form of jumpers. For mounting jumpers and racks, use tees;
4. if on sledding it will ride small childAlso be sure to make a back. To do this, use short trimming of tubes and angle under 45 degrees;
5. when the frame will be ready, you need to connect it with the polls. To do this, install it on the end and mark the markup, indicating the holes in which the racks will be inserted;
6. now drill the holes of the required diameter so that the rack can go to them;
7. after that, connect the crawls with racks, inserting them into the holes until the stop. To fix the racks in the clamns, use self-drawing;

1. at shutdown, you need to make a seat. For this you can use wooden railswhich are screwed to the frame of self-drawing or skidding.

This is completed on this process.

Option 3: Rack

Another simple and fairly useful construction design is a rack. It can come in handy in the garage, for storing all sorts of little things, in the country or even in the apartment, to convenient to put the conservation in the storeroom.

The process of manufacturing rack is extremely simple:

1. start work with the performance of the drawing, indicating the dimensions of all parts;
2. then, according to the drawing, collect racks and tie them with jumpers with tees;
3. now install the rack and place the boards on the jumper, which will serve the shelves;
4. if the rack is high, it is necessary to provide brackets for fastening the design to the wall.

Option 4: Snowshoes

How the sleighs are made for children. We figured out, now consider how to make snowshoes with your own plastic pipes for adults. To do this, you will need the following materials:

• 2 pipes with a diameter of 20-30 mm after a month and a half;
• cord from Cappon 4-5 mm thick - 40-50 meters;
• elastic for fixing foot.

The process of manufacturing snowshoes is as follows:

1. from each tube, cut a piece of 200 mm long;
2. on long blanks in the middle, apply a label and warm them up in this place over open fire, for example, above gas burner;

1. when the plastic softens, the pipes around the cylindrical subject should be bent, for example, you can use the kettle for these purposes. Wherein in the process of flexion, do not apply a lot of power, it is better to warm up the workpiece again so that it does not cracked;
2. the resulting sock once again warm up and give it an angle of about 120-130 degrees. Similarly, do both with the ends of the pipes;

1. now both ends of the pipe should be connected. To connect pipes, you can use self-drawers;
2. after that, the skeleton framework is treated with sandpaper so that the surface is rough;

1. now you need to sprinkle a mesh from the kapron cord. You can link nodes according to the scheme above.

In the process of performing a mesh, a jumper to snow windows should be tied. When the product is ready, tie gum for fixing the snow windows to the leg.

Snowshoes size depend on the size of your foot. With the size of the leg 42, a sufficient snowshoe is about 60 cm long and about 25 cm wide.

Option 5: Catamaran

Lovers active rest In nature, you can recommend making homemade catamaran from plastic pipes. The basis of this design uses external sewer pipes. big diameter. Their length should be about two meters.

The process of manufacturing this product looks like this:

1. position the three pipes at the same distance from each other and connect them to the smaller diameter tubes using the clamps or other fasteners. The distance between two extreme sewage pipes should be about one and a half meters;
2. then, on both sides, glue pipes. To reduce the resistance of floats, in front of "Bend" them, using the corners under 45 degrees;
3. on the base of the tubes connecting floats, put a wooden shield that will perform the deck function;
4. on the shield you should secure the seat that can be made from the board.

On this catamaran is ready. This swimming agent is perfect for fishermen, as well as just lovers of walking on the water.

To control the catamaran, use the oars from the kayak. Of course, if you wish, you can develop and implement a more complex design with blades on a pedal drive.

Option 6: Tent

The tent is manufactured by the same principle as all other designs - it is based on pipes and fittings. The only thing, the details do not need to glue or discourage the products to be folded. Another feature is that you will have to sew awning, for example, from tarpaulin or other suitable canvases.

The process of manufacturing the structure looks like this:

1. to make it easier to work, depict the drawing with the size of all parts and the location of the fittings. The tent design is quite simple - the basis is the rectangle, to which four racks are attached in the corners.
   Next to the racks attached roofs. If the roof is twin, then for its assembly you will need fittings for 45 degrees;

1. after that, do the tubes on the details of the desired length;
2. now, from the parts and fittings obtained and fittings, collect the frame according to the drawing;
3. next, you need to make awning. To do this, cut the material on the canvas for each side of the tent, as well as the roofs, after which they are squealing;
4. now put on the resulting awning onto the tent to make sure that the work is done correctly.

For tent use quality fittingsSo that they firmly hold the pipes and not crackdown.

Option 7: Production of cycobil

Lovers design and invent, one can recommend to make a cycle car. Truth, note that there will be more durable pipes for its manufacture than for the products described above..

An excellent solution is PVC pipes with a metallic reinforcement with a diameter of 1/4 inches. However, in the domestic market to find such material is almost impossible. It is possible to replace it with pipes from the NSPH 40 mm, intended for the pools, though their disadvantage is the high price of fittings.

In addition, it is possible to use conventional polypropylene reinforced pipes, inside which metallic tubes of a suitable diameter are inserted. Another option to increase the strength of the pipes is to fill them with the mounting foam.

The process of manufacturing a carcass of the velomobile does not constitute anything complicated. The design is assembled by the same principle that all other products - tubes are connected using fittings and thus the frame is assembled.

The most difficult when performing this task is to securely secure metal parts - the axis of the wheels, and the drive. To do this, use metal plates that can be fixed on the frame with bolts. To screw the bolt into the pipe, use bushings that are pasted.

As for the mechanical part, all the details are used from the bike. The only thing you can use the electromotor, as shown in the photo above. In this case, an electric drive is installed on one rear wheel, and the second is a mechanical drive.

To implement a mechanical actuator, you should position the axis with bending in the form of pedals, as in the photo below. This axis, in turn, transmits the torque on the "star", and then everything is like a regular bike.

Here, in fact, all the main nuances of the manufacture of cycomobiles. The other design and design tasks will surely find solutions yourself.

Option 8: Gerlitsa

If you like fishing and experiment with different gears, then you will probably be interested in this idea of \u200b\u200busing a plastic pipe, which is the manufacture of a summer gallicle. To do this, you will need a segment of a sewer tube with a diameter of 32 mm and a length of 10 cm, as well as a fishing line, hook and load.

Millets made of plastic pipe as follows:

1. remove the edges from both ends of the workpiece;
2. then drill the hole with a diameter of about 5 mm, retreating from the edge of about 1.5 cm. This hole will be used as a stopper of the fishing line;
3. now, from the opposite side of the workpiece, drill through the hole, i.e. There should be two holes in front of each other in the tube;
4. now you need to equip the workpiece. To do this, to two opposite holes, tie the suspension from the fishing line (for hanging the gallows). The suspension should end with a loop-removal;
5. now tie the line to one hole and wrap it on the tube. 10 meters will be quite enough;
6. at the end of the fishing line you need to wear a sliding load, as well as to tie a hook-tee;
7. to fix the fishing line in the working position, the tight rubber ring is put on the blank.

Now the tackle is ready, it remains to prepare a bait and go to the nearest reservoir to check it in work.

Option 9: Folding chair

If the previous version of the use of the plastic pipe you liked, then the folding is also probably necessary by the way. Moreover, it is made extremely simple and quickly:

1. from the tubes and corners, collect a rectangle with dimensions of about 40x30 cm, if you wish, you can make a chair even more compact;
2. now collect the second same rectangle. Its height should be like this, and the width of several centimeters is less so that it can be tightly entering the first rectangle;
3. now in the center of the long sides of each rectangle, drill holes opposite each other;
4. next, connect both parts with bolts;
5. at the end of the work, the rag seat is on the photo above.

As a result, you got a lightweight and compact chairs that can be put even in a backpack.

Option 10: Waterfall for children

As you know, the children love to splash in the water of summer hot days. Therefore, if you have a cottage, do not refuse them in such a pleasure and make a waterfall.

The design of this device is extremely simple. It is a P-shaped frame. In the crossbar of this frame, it is necessary to drill fine holes through which the jet of water will fall down.

So that the crossbar stood steadily on the ground, attach the legs below, perpendicular to the frame, as shown in the photo above. At one of the legs, attach a fitting for connecting the hose or threaded fitting. To the other ends of the legs, install the plugs.

Now the waterfall is ready, it remains only to connect water to it. For these purposes, you can use the tank from the summer shower or install a special container where the water will be heated under the rays of the sun.

Output

From plastic pipes, as we found out, you can perform many interesting and useful crafts. We reviewed only 10 options for their use as an example. However, if you voluntarily tense your imagination, you will certainly discover for yourself and a lot of other, no less interesting ideas.

From the video in this article you can get additional information About how the sleighs are made of plastic pipes. If some moments are not completely clear, ask questions in the comments, and I will gladly answer you.

In the event that there is a rich fantasy, as well as a set of specific skills, then almost any item can be made a beautiful thing. Very often, people are crappy crafts from polypropylene pipes. The fact is that such material is produced in different diameter and sold in almost any building store in full affordable prices. It is possible to use them not only as the construction of water supply and sewage, but also for the manufacture of various crafts.

Advantages of plastic pipes

Those who do not possess fantasy will surely ask what can be made of plastic pipes. And the answer will be quite extensive, because the material is suitable for the assembly of hundreds of various things.

It is worth noting that it is not about direct appointment Products from pipes, but about the convenience that allows you to give various forms to the pipe. Plastic structures possess quite low weightThey are very durable and durable. They are easy to clean, and besides the pipes do not collect dust at all. The positive point is also the fact that these products are not afraid of water.

All crafts from pipes are safe for absolutely all family members, including young children. They can not be cut, they are light and do not distinguish any toxins, harmful to the human body.

Usually for creative work Apply PVC pipes that can be easily connected using special adapter nozzles. Thanks to this, it is realistic to get quite peculiar and different designs. You can also use polypropylene pipes, but for the manufacture of such crafts it is necessary to purchase an additionally welding machine with which it is necessary to connect the tubes. But the disadvantage is that after the assembly, it will be quite difficult to disassemble them. In addition, the material will deteriorate after disassembly.

Connection of structures

Plastic is notable for the fact that not only various household appliances are made of it, but also furniture items from plastic pipes. In order for the design to serve for many years, you need to learn about the ways of correct connection of individual segments. A variant of the compound of polypropylene tubes was listed above, and therefore it is necessary to consider extremely PVC pipes.

Connection methods:

1. In the pickup with the use of rubber seals.
2. With the help of glue.
3. Using bolts and drilling holes.

The first way is the most simpleBut it gives an insufficiently strong connection. Before combining the design, you need to completely clean the external and inner surface of the pipes that will be connected. Eliminate all dust, and after processing special silicone lubrication. The pipe must be inserted into the socket until it stops, and after a very gently push back to about 1 cm. If you use this connection method, then the pipes can be subsequently disconnected if the need to change one of the parts will be necessary.

The second option provides more reliable fixation.But you have to spend more time. First you need to handle the docking surfaces using sandpaper to achieve a good clutch. After you need to apply methylene chloride to degrease the pipes.

The glue composition should be applied along the entire length of the required zone. After processing the pipe can be inserted into the socket until it stops, and then turn the turnover to a quarter. To happen good process Bonding, the details should be very tightly pressing and wait for so one minute. It is worth noting that all operations with glue must be produced very quickly because it dries quickly.

The last method is the longest and time consuming, because you have to start making markup, and after to prepare the surface before producing the assembly process.

If there is a need to combine the corner joint, as well as connect several segments immediately into one node, it is best to use different fittings. The design of pipes can be obtained absolutely any complexity and if you use fittings and tees.

Original little things for decorating

Absolutely any design can be made by any person, even if he was never engaged in needlework. A positive point is that for the manufacture of crafts it is necessary to use a minimum of materials, and in some cases only the shortest segments are used.

From trimming, having a large diameter, it is very convenient to build various organizers that can be placed in the garage or office. Pens, scissors, ruler or knives are laid inside.

There are several execution options:

1. The workpiece can be attached to the wall using a self-press, for which one end of the segment must be cut at a certain angle.
2. If all the details of the homemade glue together, it will turn out a rather stable figure, which can be moved to any place.

You can leave the homemade in the original color, or use additional staining. A similar organizer can become an indispensable thing for schoolchildren or those people who are often engaged in needlework or various types creativity. With such a device at hand will always be required tooland on the table - the perfect order.

And also comfort on the desktop can be transferred using a tablet for drawing and stand for a laptop. All this is also easily manufactured from PVC, which have a small diameter. It is only necessary to recall what form a school stand for books, and after with the help of pipes and connecting parts, give the same form of the product.

In each house there are bookshelves that make large quantity Printed material. Typically, such devices have rather standard forms. But if you turn on the fantasy, you can create a very original rack for books in the style of high-tech.

The apartment always has a mirror. Using short pipe segments, an option will make a very beautiful pattern that will decorate any mirror or photo. The available number of rings must be glued in advance on the manufactured layout, which is applied to the cardboard sheet. You can create a floral pattern or some abstract shape. The size of the frame will be limited only by the number of materials that can be used..

If at home there is PVC pipe having a large diameter, then it will be perfect for the structure of the shelf, which can be put on shoes. The shelf will have a large number of cells that are installed on each other in arbitrary form.

This design will not occupy a large place in the corridor, and it can store various pairs of shoes that are available in the house. A pleasant moment is that a similar shelf can be built up right straight to the ceiling. For the manufacture, it is necessary to use selflessness or ordinary glue. To secure the design on the wall, you can use a plywood sheet to which the items will be glued. And the Faneer itself can be easily attached to the wall using several self-tapping screws.

And you can always build a simple hanger from polypropylene pipes with your own hands. This will require only to connect three parts of PVC.

Vases and pots

When there is a large number in the house indoor plants, then PVC pipes having a large diameter can be adapted under the pots. On the one hand, it is necessary only to close one hole using plywood, and after drilling holes in it for drainage system. After this design, the soil will be filled and planted the plant. It is interesting to look at the design, which is not easy for individual pots standing on the floor, and connects and forms a certain abstract drawing.

Extended cylinders that have an average diameter can be made very beautiful vaseIn which beautiful artificial dried fruits or flowers are put. If you create a creative process, you can make a beautiful gift to your beloved person on any event. This vase will look very beautiful if you have an old photo on top.

Crafts for dacha

On the cottage plot You can not only work, but also rest. But for this it will be necessary to create the necessary conditions.

Homemade for giving:

Crafts for children

Quite often, grandparents are brought with her grandchildren. But they are not interested in digging the earth, and therefore they will have to entertain fidgets.

Fixtures for children:

1. If the children will come to the cottage in the summer, you can entertain them and make a football gate from PVC pipes. It will be an excellent option to spend time in the whole family, playing football. With the help of the tubes, the necessary form is made, and then any segment of the grid is fixed on it, which is available in the country area. If it is not, then you can buy in a construction store. And also need clamps that will keep the grid on the gate. For this, plastic clamps are ideal.
2. Highly interesting device Is onion made of plastic pipe. There are such varieties of tubes that are very easily bent. This can be used. The main part of the bow is made of flexible plastic. It should be bent a little, pre-warming up, and after tightening the rope, which will serve as a tailliment. Bending the pipe can be used with a construction dryer or using an open flame. As an arrow, you can use a conventional shelf, or a pipe that has a smaller diameter.

Summing up all the above, we can conclude that PVC is pretty universal meanswhich can be accommodated not only for its intended purpose, but also make very original things for home or giving. The question of what can be made from polypropylene pipes will disappear after studying options.

The graduate cottage plot is absolutely optionally to spend crazy money for the purchase of decor items for cottages. You can make stunning things with your own hands, while showing creative abilities and use the remnants of unnecessary materials. For example, if there are pruning plastic pipes about the water supply, do not throw them away.

Article on the topic: Original crafts from plastic pipes

Unexpected ideas from plastic pipes for giving

But the fantasy does not always allow the use of certain objects not for its intended purpose, so we picked up a special collection of ideas for the decoration of any room or a garden area associated with PVC plastic pipes.

Dacha furniture

Most dacities will agree with the fact that the issue of furniture in country house It is worth very relevant. No, in specialized stores, of course, a wide range, and you can choose a variety of chairs, chairs and tables.

But even modern furniture has its drawbacks: plastic darkens with time or yellowing from sunlight, the metal is covered with corrosion, and wooden crafts - Peep.

In contrast to these materials, water pipes are more durable and protected from such misfortunes, so ideally suitable for the manufacture of stylish chairs or tables.

Just enough to cut pipes with different lengths of segments and securely glue them. It is important to trace only one moment so that the legs of the subject are on the same height and the chair or the table did not flaw. A leaf of tempered glass is neatly glued at the table and you can enjoy the work of art.

Original cutting decor

if you cut pipes with small rings and process edges, you can create any decor items. It may be decorations on the wall, frames for paintings and mirrors or original openwork partitions. For this rings, you can glue or connect any way convenient for you.

Light, but reliable gazebo is fashionable to collect literally in a few days, and it will look original on garden plot, and it will cost many times cheaper than wooden.
Enough to collect metal carcass and paint it into white color, and from pipes different size Cut the same ring thickness. With the help of an adhesive gun, the rings are glued according to the size of the frame and are strengthened.

It will only be possible to think about whether the gaze is painted, or leave in traditional white color. Believe me, neighbors will be visible!

Tip! From such a design, you can make not only a gazebo, but also a simple canopy for the summer kitchen. If necessary, canopy can be covered with a film to protect against moisture, or suspend the mosquito net.

Article on the topic: how to make a gazebo from the vine with your own hands

Stylish shelf for storage

Cutting different over the diameter of the pipe of the same height and gluing them between themselves, adding a cute chain or twine, it turns out an excellent shelf for various small items or a stylish decoration for the room.

In the country, people constantly live, someone comes, someone leaves, and the shoes need a lot: for home, work, recreation or rainy weather. Securing the suitable size on the wall of the pipe or gluing them with each other, it turns out a stunning functional storage system. Now there will be order in the lobby, and the desired sandal is not lost.

Storage little things

In the workshop, as a rule, it is very often impossible to find the desired screwdriver or drill. If you cut the pipes and one side cutting at an angle, then the pipes can be attached to the horizontal surface. Now all the tools will be in place and not lose!

For storage of inventory

After one or another design was collected anyway, small pipe trimming remains. From such trimming (preferably the same size) you can make very comfortable fasteners for gardening inventory (shovels, rakes, mops and snowballs), as well as in the kitchen for storing various accessories.

In a barn or other reserved place to store these things in the farm, it is enough to attach pipes to the wall on the desired levelAnd the inventory will cease to bother under their feet (and in the case of rakes it is dangerous for life) and will hang in place. Free space and room will be free and convenient.

For wine bottles

The principle of gluing pipes, as in the previous embodiment, it is important only to measure and cut off the pipe of the desired size. Keep such a design with wine in a niche over entrance door or above the refrigerator.

Original flower vases

If you carefully handle the edges of the pipes, and cute vases for bouquets can be decorated with your own taste. For decoration, you can use acrylic paints, ribbons, decorative pebbles, and indeed everything, there is a hand.

See also: Second life of glass cans

As can be seen from the above-described variety of plastic crafts pVC pipes Allows the gift book to fantasize. This type of material is quite accessible, durable and durable. Well, about the country crafts that are necessary in the conditions of dacha life to judge is definitely the reader of this article.

It is interesting

geoinzh.ru.

Crafts from plastic pipes PVC (38 photos)

Do you know that PVC plastic pipes can be used not only for their intended purpose, but also for additional structures And simple crafts that are made with their own hands. In fact, they are also exploited as racks, furniture, various decorative ornaments and accessories. Therefore, if you have extra plastic pipes in stock, do not hurry to throw them out. Better try to create crafts for home or garden.

PVC pipe table

The first thing you can try to make pipes with the addition of wood is a low table. Used in the country or in the garden.

PVC and Tree Pipe Table
Unusual dining table of plastic pipes

Wooden and plastic pipe rack

Another objects that is executed from PVC plastic pipes. It will fit perfectly for the garage or storage room. It looks quite interesting and stylish. You can store various small things.

PVC pipe rack for pantry with their own hands

Alternatively, make a rack for an apartment, which will be able to put an audio system, TV, souvenirs and books.

Rack for the hall of plastic pipes

Unusual option Shellage will also be interesting for you and others. It seems that it was specifically developed for some particular items. Additionally, it is possible to decorate all with beautiful accessories.

Pipe rack and boards in the interior

Coffee table with a tabletop

In this variant, the pipes will be used as legs. So that they can withstand, the glass countertop is recommended to further strengthen them.

Coffee table from PVC and glass pipes

Bed with Baldakhin

Another extraordinary way to use PVC pipes. It may be as a decor in the country.

Bed with a frame of pipes in the interior

Canopy from pipes

Canopy above the bed can also be made of plastic pipes.

Beautiful canopy over a crib from old pipes

Towel hanger

It will be an excellent addition in any kind of life. It will look not only interesting, but will be practical thingwhich can be used.

Dryer for towels do it yourself - crafts from PVC pipes for cottages

Children's chairs

Cute unpaired chairs for kids. The frame is made from PVC pipes, and the seat can be weave from ordinary threads.

Chairs for children from pipes and threads

Hiking chairs

Small chairs for nature or hiking will be simply indispensable. Made quickly and occupy little space.

Chairs for hiking

Manege for children

Using PVC pipes, build a frame where your kids will be able to play. It will be the so-called gaming zone that can be placed in the garden or in the country.

Place for children's games made of pipes

Bar stand

Using a conventional PVC plastic pipe, you can create a whole resort on which there will be a bar counter, painted in the form of a bamboo or other exotic dicks. There is a chance to arrange a complete party dedicated to this topic.

Bar rack from plastic pipes PVC

Children's Molbert.

A lightweight tablet from pipes and paper is perfect for a fun pastime of your children.

An extraordinary "tablet" from PVC

Plastic Pipe Organizer

An organizer for the table, made and painted in any of the colors of the palette will help to clean up your desktop.

Simple Organizer for Wall Table Table

The same organizer can do in the bathroom. Now all dental brushes, pastes and other bath accessories will always be in their places.

Bathroom Organizer

Chojnik

The shoe compartment made from plastic tubes will ensure the reliable storage of your shoes in the place specifically reserved for this.

Organizer for shoes in the hallway from large pipes

Shelf for wine

it a good option The use of pipes as not only shelves, but also a whole cabinet for wine or other bottles.

Shelf for wine with their own hands

Stand for working on a laptop

Easy in manufacturing and use. From now on, work on the laptop will be only joy.

Functional Stand for Laptop

Eaves for Tulle and Curtains

Do not believe, but the caretaker from plastic pipes in the form of a cornice will look not only bright and creatively, but also very extraordinary. Ego you can paint or simply issue various decorative elements optional.

Curtains for curtains in the apartment

Home Decor from PVC pipes

Another option to use PVC pipes is to cut them into their rings and use as decoration for dresser, tables, hangers, cabinets and any other furniture in the house.

Chest decoration with PVC plastic pipes

Frame for mirrors

Similarly, you can cut the pipe with rings, lay out the drawing or frame from them, and thus make a mirror.

Pipe rings mirror frame

Piggy bank

Original approach to the use of plastic PVC pipes. Such a piggy bank is quite possible to build for a gift, or use at home as a souvenir.

Original Pig Piggy Bank

Vase

It can be given to any holiday. Fasten the PVC pipe at the base, place at will and put flowers in a vase.

Personal vase as a gift

Lamp-bone from the pipe

It is done quickly, but it looks very extraordinary.

PVC tube lamp

Bracelet

Do not believe, but few people guess, of which such a bracelet is actually made. Using PVC tubes and a little fantasy can be achieved and not such heights in the manufacture of jewelry.

Pipe bracelet with your own hands

Pot plant

One of the most common options for using pipes.

Pot for home plants with their own hands

This is not all variants of crafts that can be made of pipes. But they are enough to be interested in this art, and continue to practice the performance of various sodes.

Master class "Greenhouse from PVC pipes"

If you have a garden and a garden, you are undoubtedly you know that the use of greenhouses as a place where those or other plants can be very important. Therefore, we will try to make such greenhouse conditions from PVC plastic pipes with their own hands.

Greenhouse from PVC Arched Shapes

For work, we will need the following materials:

• PVC pipes with a diameter of 25mm.
• Tee and crosses for our pipes. Also worth stocking tees.
• Reinforcement wooden plank, Metal strip.
• Hacksaw, which is suitable for cutting wood or metal.
• Welding machine for plastic pipes.
• Screwdriver and screwdriver.
• Self-tapping screw, hammer, nails, roulette and construction level.

Process of working steps

1. To begin with, we need to take the boards of the desired size. It is better at will, the width is desirable about 20 cm. They will definitely need to be carefully soaked with an antiseptic agent.
2. At the previously aligned land, we install a rectangle from the boards, in the corners, consolidating its reinforcement, which is driven into the ground. He must be proper form. You can check it with the diagonal of the indoor rectangle.
3. Next, we need to fix on the sides (those that are longer) the segments of the reinforcement with the settlement so that it remains 50-70 cm on the surface of the earth. It is for them that arcs will be attached.
4. We divide the width of the base approximately in half, while the middle of the board mark the marker. From her we must retreat 40 cm. In each of the parties, with outdoor Also clog the board.

Process preparation and installation of pipes

To get a full-fledged arc, we will need to cook two pipe segments. They should roughly compose 30 cm. Each. In the middle we insert the cross. Outdoor parts we fasten with plastic tees. Arcs are installed on the principle of putting on the end of the pipe to fittings, which is located among the two long sides of the base.

Mounting process of armature

Next passes the installation of the central rib rib, which will allow to keep the design in equilibrium. It is made of pipe segments with a length of 85cm. And welded in the middle between the Cross and the central tee. It is fixed directly on a wooden base with self-tapping screws and metal clamps.

The final stage will be the process of creating doors and windows. It is necessary to predetermine where it is best to place them. Usually in the end, the greenhouses will be installed the doors to have the ability to air. In the opposite part of the door, you can set the window.

View of the greenhouse from the middle

Plated greenhouses from pipes can be polyethylene or polycarbonate. Basically, this kind of greenhouse will be used seasonally, as it is not entirely suitable for all time. It can be noted that the most popular size for the average greenhouse will be an option approximately 3.82m. by 6.3m. It is optimal and functional in operation.

Summing up can notice that there are quite a lot of interesting ideas associated with crafts from plastic PVC pipes. The main thing is to decide what exactly you need, and just try to make it yourself. It can be ordinary souvenirs in the form of piggy bank or bracelets, or designs by type of furniture and greenhouses.

Comments Powered by Hypercomments

decorwind.ru.

Useful crafts from plastic pipes with their own hands

If you do not be lazy and not be afraid to show the initiative and the smelting, you can work miracles from any submitted means and materials. And make comprehensive crafts from plastic pipes with their own hands of any formation and is easier.

Many plastic pipe varieties. There are pipes from which the heating network is mounted, pipes intended for water supply and sewer, etc. and are usually all relatively cheap and available for purchase in any specialized store. Often, after repair or construction, many different pipes remain, which can be an excellent raw material for the manufacture of all kinds of crafts.

It is probably prepared for the removal of a certain amount of various pipe trimming on the dump. Do not hurry to throw them away, and first read this material.

Advantages of plastic pipes

Here it will be not about special purpose of pipes, but about their use just "not for the appointment". Plastic pipes are easy, durable and durable. You can easily care for them, dust is not going to them, and the products of them are completely safe.

Most often for crafts use PVC pipes. They are durable, have increased rigidity and of them it is easy to collect a variety of structures through all sorts of corners, adapters and nozzles. Good and polypropylene pipes, but products from them will not be unintended. In addition, to create from such pipes, you will have to learn how to use the special soldering device.

Methods that pipe connected in the design

Plastic pipes are good not only for the manufacture of all sorts of household trifles, of which you can also construct all kinds of furniture items. In order for the resulting item to serve for a long time, all the details of its designs must be properly connected to each other. Consider the assembly of structures from segments made by their PVC pipes.

Methods that can be used to connect such pipes:

• connect the segments by the termination and rubber seal;
• by means of special glue;
• with bolts, drilling holes for them.

In the case of a socket, the compound is easily reflected, but not strong enough. Before the procedure, it is necessary to thoroughly clean the pipes in the places of their connections from dust and other pollutants, and after applying a special silicone lubricant to the pipe inserted. At first, the pipe must be inserted to the end, but then it is recommended to push it to a centimeter back. This is done in order to subsequently be able to disassemble if possible.

Next way More reliable, but also more time consuming. But in this case, the product will be strong, reliable and durable. For good gluing Before mounting the part in the connection places for the best hitch are processed by sandpaper. After processed places, they are dengulated with methylene chloride and ready to apply glue. The glue is applied both on the treated outer surface and on the inner. After the pipe docile, and bringing the pipe to failure it is worth checking on a quarter of turnover. The details should be tightly pressing each other for a minute, and so that the fixation is the maximum best to do the gluing procedure very quickly. After glued segments should dry out for several more hours.

The most time consuming method is the third. In this case, it will have to be placed and drilled a set of holes, but this option will provide the future product excellent strength and reliability. In addition, it is not necessary to mess with glue and sandpaper, and after the assembly it is not necessary to wait for something there will dry out there.

In order to create corners, all kinds of branches, etc. Mono use a variety of fittings, due to which the design of any complexity can even collect a person in these affairs. So, proceed to consideration useful productswhich were constructed by the same private craftsmen as we are with you.

Video: crafts from plastic pipes with their own hands. Part 1

Crafts designed to decorate the interior with useful features

Of the shortest cuts of a small diameter, you can make it possible to make convenient and practical organizers for the garage or workshop.

Also from pieces of pipes are obtained by good laptop stands or even the original easels for drawing.

Bookshelves The PVC pipes look amazingly, besides, they can be performed in a variety of and extravagant configurations.

Useful on the topic: Interesting ideas of a well design at the country

If you cut into the pipe with small rings, you can build truly excellent compositions that you can subsequently decorate any room.

Cutting pipes of large diameter will be good for creating shoe shelves, as an option to craft from plastic pipes in the photo.

Also from PVC tube, amazing stands for flowers are obtained,

and from the pipes of a wide diameter, the original vases will be released, which will be an excellent version of crafts from plastic pipes for giving with their own hands.

From the pipe of the middle diameter you can make vases for flowers. Especially excellent they will look if plays them with colorful pictures or photographs.

A truly amazed and delighted homemade original lamps from short trimming PVC pipes.

Also from the remains of pipes, you can build such useful things like a hanger or a bag holder in which garbage bags are folded.

Products for playgrounds

From PVC plastic pipes as an option to craft, it turns out an excellent playpen, which does not exist even in specialized children's stores.

With such pipes, delightful and aesthetic children's swings are overlooking, dried from the past summer rain in a few moments.

Also from pipes can be constructed magnificent and super light baby sledges.

Football gates performed performed from PVC pipes perfectly.

You will delight the Datvora and crafts from water pipes - frame for a kindergarten. It remains only to consolidate the blankets on it, and the "building" is ready for the game!

But the model of an extravagant summer soul, under which even adults will not be revealed.

Theatrical shirma, designed from the pipes, is also delightful.

Furniture items made of PVC pipes with their own hands

From PVC pipes, wonderful chairs are obtained. Having attached a little effort and smelting, you can create real masterpieces of furniture art.

Can be made even wonderful bunk bed for babies. It remains only to buy a mattress, and sleeping places are ready to use. Saving money is evident.

And such a coffee table is generally unlikely to distinguish from the factory, so natural, aesthetic and tasteful it is made.

an excellent idea will be built from plastic pipes racks for all sorts of objects that will be excellent to save place in the home.

Useful fittings for home and summer cottage

Where, where, and in the country area there will be a place and the use of everything that can remain from home repair, and pipe trimming - and suppressed.

Useful on the topic: Winter Garden In evening lighting

Several small segments and tees - and now is ready for a wonderful and easy dryer for the linen. It is easy to wash, plus the plastic does not rot and does not rust.

After the pool or work on the garden beds, you can relax in an excellent chaise lounge made of polypropylene pipes.

From such pipes will come out and a wonderful canopy for cars. Just because of its extreme ease, it will be necessary to be carefully fixed, since it can be demolished by any sharp impact of the wind.

Excellent and arched garden entrance, made of polyethylene pipes. Give the desired bending pipes can be gradually heated by their gas burner.

For the construction of a simple gazebo, it will be enough for the pipe in the ground with one end in one place, bent, fasten the other end in the next intended place, not forgetting at the same time to wear a specially prepared peculiar agent to protect against the sun.

You can construct from pipes even unpredictable fixtures and devices such as supports under the field and wheel trolleys, stands for fishing rods or input wickets. The variety of products from these materials may be limited only by the scarcity of human imagination.

Sewer pipes - ready-made hens for chickens.

And from PVC pipes, among other things, you can make as a small guy, and an impressive seasonal greenhouse.

Wide plastic pipes are just a discovery for dackets strangled in the sowing square. Of these, you can build up vertical beds of all kinds of configurations.

Truly the crown of architectural art is such a fence made of PVC pipes. This is a rather complicated building, it is not suitable for care, as well as quite durable, because plastic serves much longer than any tree.

It is not difficult to come up with your varieties of plastic pipes. Enough to do so enjoy, wide imagination, free timeAnd, of course, a sufficient number of pipe trimming, remaining from repair, is exactly those that you prepared to throw out on the trash.

Video: Crafts from plastic pipes. Part 2

ideiddachi.ru.

Crafts from plastic pipes PVC do it yourself | What can be done from polypropylene trimming - master class

Plastic products They are firmly included in our life, imperceptibly pusing many of their analogues. And the most common among all such products are PVC pipes, which in view of their insignificant cost and practical use are found everywhere. And today we will tell about how to use them non-standard and what interesting things can be made with their own hands.

Amazing things from consumables

It is difficult to list all the products that can be done with your own hands, having only fragments of building materials at hand, as well as fasteners for their connection. Applying such raw materials, you can create incredible and necessary things.

Ideas to create crafts from simple hollow objects are really countless. It can be like ordinary organizers for organizing a working space and a support for a laptop or tablet and designer masterpieces (chairs, beds, coffee tables And other furniture), which emphasize the personality of a person.

Objects and products made of polypropylene pipes with their own hands is the most appropriate activity for people with a rich fantasy. At the same time, it is not necessary to purchase specialized equipment and tools for the production of household crafts from plastic, because such materials can be shrinking quite simple.

Such designs can be:

And, if the second method is more suitable for stationary interior products, then the wizards interested in the production of seasonal things are treated to the first method of installation. For example: Folding fishing chair, greenhouse, canopy and gazebo, garden swings, etc. Such structures can be easily assembled on the eve of the season, and then remove for storage, not experiencing that they will ruin in winter.

Crafts from hollow polyvinyl chloride pipes possess a huge number advantages. Among the main - durability of raw materials and aesthetic appearance finished products. It is also important and relative low cost of materials, which is a great temptation for many people who want to try out their strength in creating universal plastic objects.

The rest of the benefits include:

1. Practices of installation and operation.
2. The strength of structures due to high density of raw materials.
3. Variety of variants of crafts (configurations, sizes, appearance).
4. The ability to create exclusive copyright items that can later be placed on sale or present as a gift.
5. Absolute safety and non-toxicity of raw materials allowing to use crafts in a wide variety of rooms and conditions.

Whatever you dreamed of creating a design, you should remember that the main raw materials (pipe trimming) can be presented quite easily, but you will have to prepare the fasteners and tools in advance. The same bolts, plugs and fittings - it will be necessary to first calculate how much it is necessary for those or other parts.

In addition, it is also necessary to prepare utility tools that can be useful in the process of creating an exclusive:

• pencil and ruler / roulette;
• drill and screwdriver;
• glue or screws.

If you decide to bend materials to obtain a product of a certain form, please think about how exactly you will achieve the desired result. In general, crafts from fragments of plastic pipes are made easily and simply, in which you can make sure by reading this article to the end.

Ideas for preschool institutions

Very often PVC pipes are used as the most optimal raw materials for the manufacture of furniture and considerable items for children. For example, small chairs, low tables, shirms for game zones, football gates for games on fresh air etc. There are still quite a lot of useful and interesting things, for the manufacture of which is suitable inexpensive pipes from polyvinyl chloride.

For example, to organize leisure children in children's garden, You can make a mobile puppet theater. With that, you will need only a few pieces of pipes and connecting elements to create a frame-frame, as well as matter - for the curtain. As a result, it may turn out very attractive, and most importantly - the invention needs for kindergarten.

The frame can be made in the form of a screen of two carrier supports, two jumpers and outdoor frames of four tubes, as shown in the photo below the left. You can also make your own hands with a more complex design - a screen of three sections, for the manufacture of which it takes a little more consumables and time.

No less actual fixtures from polyvinyl chloride pipes for organizing leisure children in kindergarten:

• developing stand (bizeboard);
• sink for hands or toys;
• cot for dolls, etc.

Another necessary for kindergartens design from PVC pipes is parking for bicycles. Such a stand is easy to make with your own hands, even if you have not previously dealt with the installation of pipelines. In order to build such a setup, two long and two short fragments will be required for the base, as well as several more pairs of identical segments for the holding wheels of the racks.

Actual for any time of the year, the device is a towel dryer, a laundry basket and a plastic pipe hanger. Similar structures will be indispensable not only in kindergartens, but also in ordinary residential buildings. Made of sufficiently light and cheap materials, they can serve their owners for a long time.

Best ideas for country houses

The happy owners of private houses outside the city can also be used PVC pipes with benefit. Those who come to relax and relax in nature can be made from such materials chic arbors and canopies. And for fans of cinema, it is possible to implement a homemade cinema of the canvas stretched into the frame from polyvinyl chloride pipes. What could be better than a pleasant company and an open sky, under which you can organize a home evening with friends from a large screen. By the way, the remnants of other building materials can be used as a canvas. For example, remaining after repairing pieces of stretch ceiling.

The same garden furniture can be made with their own hands from pipe segments. Tables, folding chairs, comfortable garden chairs and even chaise lounges - these products can be done by spamming the blueprints on the Internet or developing your own project.

For example, you can use images and schemes of garden furniture:

Incredibly beautiful, reliable and comfortable from polyvinyl chloride tubes, benches and swings are obtained. And the most important thing is that the production of such structures does not require significant cash investments. Yes, they will serve for a very long time, pleased not only by the owners, but also their guests.

For those who come to the cottage not only to relax, but also to work, there are also several ideas for the arrangement of their pricework. What can be made of pipes of plastic pipes that remained, let's say after replacing the pipeline? Yes, a lot of things! It may be not only necessary primary installations and devices and decorative structures to decorate the territory adjacent to the house.

For example, if you prevent you from the hose, and there is no suitable place to store it, do it yourself a stand from tubular trimming. Those who wish to quickly construct a fence for flowerbeds or damage from neighbors, you can apply the same material. As you can see by photo, plastic will fit perfectly in any atmosphere and help keep your vegetation from animal encroachment.

Lovers of homework can be used plastic hollow structures to create pens and cells of various configurations and sizes. Cheap mobile structures are obtained, which at the same time look very aesthetic. It is worth noting that materials and with a large hole can come in handy. Homemade crafts from sewage pipes allow farmers who hold birds (quail, chickens, etc.), do not worry about food for their wards. Filed from above in the chute feed will come to the feeding zone.

Another relevant product for the summer season from polypropylene pipes with their own hands is a shower-arch and a frame for watering. It is so banal structures that they will not even need a scheme for their creation. All you need is a few trimming from PVC collectors, fittings for their compound and, of course, a drill to do the water holes. Next, you need to connect the hose to one of the ends of the pipes, and to put on the rest (except for water holes). And, voila - you got a portable shower and a frame for watering a garden, lawn or flower beds.

Fans of gardeners gardeners can not do in the country without a greenhouse. By the way, it can also be done, having only trimming of building materials at hand: pipes with a diameter of 25 mm (or 32mm), rods, boards, film and fasteners. Detailed master class, as from such a set of materials to make a greenhouse with your own hands, is given in the video clip:

Do not do in the country area without a stepladder. Yes, and in the apartment such a design would not be superfluous. How to make such a wonder staircase, you can see in the next video review:

You can use such a building material also when the temporary canopy is erected for the machine. This design will be very easy, it will be possible to quite simply collect and disassemble if necessary. Moreover, given the durability of raw materials, a plastic canopy with a frame of pipes can be performed on an ongoing basis with other building materials.

What structures can come in handy in an apartment?

I wonder what you can do from PVC pipes for the apartment, you can find a lot of original and practical products that will significantly simplify the life of an ordinary city inhabitant. For example, they will turn out compact and at the same time fairly spacious shoe shelves. Measuring a pre-width of the feet of the dwellings of the dwelling, it is necessary to choose the segments of the optimal diameter pipes.

Great for creating such shelves sewer collectors, which can be decorated after gluing own willing. Cutting a tunnel on equal pieces, they can be glued or strung by forming into several rows so that the shelf can accommodate the number of pairs of shoes. As a result, it may be quite a pretty artwork, which does not take a lot of space in the apartment.

The same fragments of collectors can be used as a kashpo for growing colors on the balcony or on the windowsill. The same pipes, only in the form of a one-piece design, can be composed in the "vertical garden", this is a very actual invention for those who live in the city, but wants to grow greens on the balcony.

The vases for flowers, organizers for stationery or kitchenware will be originally pretty. To create such crafts, just a few screaming of collectors with the same or different diameters is sufficient. Cutting off the edges of the product at one angle, and after, gluing them into a single design, you can get a stylish stand that will save space on work zone.

We use similar materials also in the bathroom. From ordinary segments or tees can be made on the principle of shoe shelves, comfortable holders for a hair dryer and a flock, shelves for towels and other items that can be found in the bathroom.

And, of course, furniture. From PVC pipes, it is possible to make very practical and inexpensive, and most importantly - original interior items - beds, chairs, coffee tables. Also, applying such raw materials, you can make furniture in the children's room. The safety of the material perfectly allows the use of pipes from polyvinyl chloride in residential premises and at the same time not to worry about the likelihood of allergies.

As you can see, the scope for fantasy is just a huge. Deciding to try to make it possible to craft from PVC pipes, it is not necessary to attend special classes or acquiring expensive equipment for this. Using what is practically in every home as a primary means, you can make exclusive products from ordinary materials that will become a very unusual addition for your household economy, garden or apartment interior.

How do they make a fountain in the country

Corner relaxing in the country with your own hands

At the moment, very many people have PVC pipes in their farm. If they already have time to get bored, then in no case do not think from throwing away and change to others. They have a whole mass of advantages.

First of all, it is impossible not to mark a pleasant white color. It will be perfect for creating interesting techniques. In addition, the most common glue can be used to bonding elements. If you do not glue everything, it's even to the Lixture. You will receive a kind of designer Lego. Consider interesting ideas that can like you. You yourself might think what you do is just enough to show your vanatasy.

Just look at the children's chair shown below. Surely you want to build it. The temptation is very large.

From one pipe you can easily make a folding chalter. It is perfect for a picnic.

Want to keep everything organically? Then just create a set of several chairs and a table from the same pipes.

Excellent and children's two-tier bed. But you need to choose the pipes of the optimal diameter so that the load is distributed.

If you have a dog at home, then for her you can create a bed. It is only necessary to take into account the weight and sizes of the dog.

From the pipes 1/3 or 1/2, you can make a very good stand for your laptop.

Want to get a good dirty laundry basket? Then just make it from the pipes. It is only necessary to make calculations according to your needs. Just look as far as Zhto looks stylish.

You can make more large-scale things. In particular, suspended swings, which can be performed perfectly at the cottage.

There are only remnants from PVC pipes? Then you can simply add a bottom to them and store handles, pencils and more. It looks all this very creative.

What can be made of plastic pipes? Yes, almost everything! Most immediately the question arises: "Is it possible to replace PVC pipes on polypropylene?". Polypropylene tubes can be used, only in this case we will need a soldering iron. Advantages of PVC pipes: - Snow-white color; - connect pipes with fittings using glue, or without it without it; - If you do not use glue, the design will be folded, and like the Lego constructor you can use fittings and pipes for the assembly of other structures. Of course, polypropylene pipes are deprived of these advantages.
And now, let's see which crafts can be made of plastic pipes with your own hands: can be made of plastic pipes: Children's chair from 1 "pipe
Matching chair out 1 "pipe

Table tables and chairs from 1 "pipes for use on the street Greenhouses, greenhouses and light frames on garden shelter beds, assembled from polypropylene pipes and connecting elements - a very budget version that combines the cheaper and simplicity of assembly. If necessary, it is also easily dismantled. Strong and stable racks for growing and working with seedlings. PVC pipes, larger diameter, neatly dug up with an electroll bison and soil filled - compact and aesthetic option For planting greenery. Children's 2-tier bed (used pipes with a diameter of 3/4 ", 1" and 1/4 ") Bed for dogs, the diameter of the pipe in this case is selected based on the dimensions and mass of the dog. Suspended swings For dacha
Sani for business work in winter in the country
From the remains of pipes of large diameter, you can make a small organizer in the garage PVC pipe dryer.
Attaching the wheels, we get very comfortable carts.
The greenhouse from PVC pipes will serve you for many years, it is not necessary to paint, while it will not rot or rust, as usual happens with the greenhouses of their tree and metal.


From plastic pipes you can collect hydroponics, but in this case I want to note that any pipes can be used (including sewer) Children's car from plastic pipes
Or make a pump for chickens
Racks that can be easily gathered under any sizes
Collapsible street tents and plastic pipe tents Lattice for grapes from plastic pipes which will always have a pleasant appearance. Sheds for cars from plastic pipes
Fences and fencing from plastic pipes
PVC pipes easily accessible material for useful ideas and fixtures in the farm. What do you need for this? Hacksaw, roulette, glue, in some cases sandpaper. Drinking system in chicken coop.
Stelms.
Rack for bicycles.
Shelving for containers with vegetables. Various tool holders. For storing shoes. Summer shower for kids.
Non-housing designs of garden furniture collected from polypropylene pipes will help you to relax and relax in the shady corner of the garden. How do you, for example, comfortable models of chairs? Comfortable chaise lounge, improvised canopy for morning meal in the fresh air or is such a stand model in the spirit of "lifehak", allowing you to train on the treadmill without leaving the Internet? Cheap, reliably and practical!
Children at the cottage is a separate burning topic. An ubiquitous defector must be given the opportunity to play and disgrace in such conditions so that parents are calm. For kids in the country, you can collect this convenient playpen or cozy toy house. These structures are easily transferred to the garden or on the veranda, and your child will always be in the field of your vision. Tasty Thaws will surely come up with water games. Swing: House for games

As you can see, plastic pipes can be used in any industries (and not only for direct purpose), and where exactly to use them depends on your imagination.

kaksekonomit.com.

What can be made from PVC pipes - a selection of the best 38 ideas

Hello, dear readers! If you carefully look at the subjects around us, while connecting fantasy, then you can find each of them at least several applications. It would seem that you can do from PVC pipes, because they are used exclusively for the installation of sewers, in fact, this material is just a find for craftsmen. After all, the simplest PVC pipes can easily and quickly transform into incredible household items, below we have prepared for you a whole selection of current ideas on this topic, Well, of course, each idea is supported for clarity photos.

What can be made of PVC pipes.

How to give one or another PVC pipes.

In order for the subsequent pipe to be bent or flatten, it must be heated with a gas burner, and immediately give the necessary form. In extreme cases, if there are no burners in the house, you can heat the tubes over the fire of the gas stove. And you can cut the pipes with a saw for metal or a jigsaw, to connect all parts using cold welding (for this you need to purchase a special adhesive composition).

1. Trunk for the car.

Here is such a trunk for cars can be built from water pipes. No less interesting is the holder for a bicycle on a car.

2. Fortor on the bed.

So that the child did not fall from the bed at night, you can make an improvised side.

3. Burning for door opening.

This gate can be made on the doorway, so that the child will not be able to leave the room limits.

4. Vase and flower pots.

I cut off the cylinder from the pipe of the desired length from the pipe, and it is possible to obtain a remarkable vase in the end with a self-adhesive spectacular film, which can be installed with water with water and put live flowers.

5. New Year decor.

Festive wreath.

Cut the pipes of different diameters on small the same cylinders along the length, glue them together forming wreath, stain suitable paint From the can, on top drilling holes and told the rope, hang the wreath on the wall, and in several cylinders we put small christmas balls.

Wall Christmas tree.

We take pipes of different diameters, cut them on cylinders of the same length. We prepare the canvas, stick the cylinders on it, forming the outline of the Christmas tree, create a footboard from a large pipe, hang the composition on the wall, and in different cylinders we invest various Christmas decorations.

6. Children's waterfall.

To harde the child, you can prepare such an improvised waterfall, connecting two hoses with the included water to the steps, and having done the hole for water drain in the upper bar.

7. Children's house.

Children love to build various houses, halars and other asylums, it is possible to make it easier for them to prepare the framework of PVC pipes, and sewing the cover from the waterproof fabric.

8. Tent for the pool.

Such an awning in addition to creating the shade, can also serve as a gate for water polo.

9. Holder for glasses.

Great idea For a street bar, a slot is created in the tube in the width of the layer of the glass, the legs-holders are screwed from above, for which the design is attached to the ceiling surface.

10. Place for bicycles.

Such a "stall" for children's bicycles or scooters will help keep the courtyard in order.

11. Cells for wine bottles.

In large cylinders of pipes, glued together, you can store bottles with wine.

12. Stand for a drill.

Stand for a drill will help create identical holes in strictly defined places of products.

13. Stairs for cats.

Cats are very mobile creatures that value freedom, therefore, in limited premises, they begin to wake, so that it does not happen, they need to constantly take something, and will help in this case such an interesting design with slides, stairs and crossbars.

14. Vertical flowerbeds for strawberries.

In the PVC pipe with a drill with a special round nozzle, drill large holes, then the pipe is to go to the ground, and pour into it the soil, and then fall into the round holes of strawberry seedlings.

15. Stand for kitchen appliances.

From such pipes may turn out a wonderful stand for forks, knives and spoons.

16. Stand for scissors, pencils and tools.

Connected pipe sections on a wooden plank can serve as pencils. And vertically spaced cylinders can be supplied for tools. So that the tools do not fall down, the bottom of the pipes can be made by mounting foam.

17. Stand for a laptop.

Their such pipes may be a wonderful stand for a laptop, especially since the parts are not very necessary, several, several tubes and connecting elements. In conclusion, the product can be painted from aerosol canister In any color.

18. Cells for shoes.

Summer shoes can be stored in pipe cells, and so that they look more presentably them can be saved by a suitable adhesive film.

19. Organizer for scarves and underwear.

Special containers with cells are sold in stores in which you can store underwear or other accessories, and then such an organiser can be created independently, just cutting PVC pipes on shallow cylinders, and gluing them together.

20. Partition for fusing plants.

From such pipes, you can create entire fences or partitions for which curly plants will be placed in the subsequent.

21. Stand and holder for curling or hair dryer.

Thanks to such standings - hair dryer, iron and curls will always be in their places. And also after use, you do not have to wait when the curl or iron is cooled.

22. Pan for dogs and other pets.

So that newborn puppies or kittens crawls who are where, you can build a small aviary. Well, more active animals you can create a large full-fledged pen, without forgetting to cover it with a grid.

23. Holder for the watering hose.

To garden hose Not fused under his feet, it can be stored on such an excellent stand.

24. Frame for summer gazebo.

Continuing the topic of what can be made from PVC pipes, we want to show you a great seasonal idea for a gazebo. This design It is possible to cover with an awning or hang on the sides of light curtains, which will be even better to grow up even at the easy blow of the breeze.

25. Frame for the street cinema screen.

Lovers of watching movies with friends will appreciate the idea of \u200b\u200ba street screen, its frame can be made from PVC tubes, and the screen itself from the remnants of the matte stretch ceiling.

26. Keheli.

Children will be delighted with such mini bowling.

27. Puppet Theater.

To create such a children's theater, you only need to collect the frame and hang the curtains.

28. Stand for the sandbox.

The child will be more comfortable to play in the sandbox, if it is raised above the ground, and the sand will not fall into the shoes and the baby's clothes.

29. Rack.

Such a rack will allow to keep the room in order, as it can accommodate an unlimited number of things and toys.

30. Frames for paintings and mirrors.

The ring glued with each other, sliced \u200b\u200bfrom PVC pipes, will eventually serve as a remarkable frame for a picture or mirror.

31. Luminaire.

Lamps from plumbing pipes are very beautiful, especially if the pipes are decorated with rhinestones or supplemented with curly slots. To embody the idea, the pipe with pre-created beautiful and elegant slots is installed, the basement with a light bulb is installed, and from the reverse side of the product a hole is created to exit the wire, it remains only to connect the lamp into the outlet, and enjoy an interesting muted melting.

32. Table.

From PVC tubes, you can collect a wonderful table, covering it wooden countertop Or to build a shop (at the end of the article video will be presented, how to make a shop from such pipes).

33. Chairs.

From such pipes, excellent garden chairs are obtained, the smooth lines can be achieved if heat the pipes with a gas burner, to give the right shape and left in such a state to cool. But even the usual geometric chair will look great, the seat can be created from ordinary sieve or cotton fabric. But you can go further and create folding chairs that will be very relevant on vacation, for example on fishing.

34. Dryer for linen.

Such a portable laundry dryer is very useful in the farm, because if necessary, it can be removed from the eye, as well as transfer from the shadow part of the site to the solar. If the rain suddenly goes not to run to shoot still unexpressed underwear, but simply transfer the dryer under the canopy. Some advantages.

35. Transport.

Their PVC tubes can create a full-fledged children's transport or trailer, children will be delighted with such machines.

36. Football gate.

Children can freely play football with such a great gate.

37. Chaise lounge.

Excellent solution for giving - Sun loungers collected from PVC tubes, sun bed can be sewed from dense tissue.

38. Shirma and partitions.

Please note how fashionably it looks like a partition created from PVC cylinders, for this it is necessary to cut the pipe to the same segments, and then build a partition from them, gluing each cylinder to each other. No less interesting is the shirma of PVC pipes, which is screens with strung curtains.

How to make a pvc pipe onions:

How to make a shop from PVC pipes:

Dear readers, today we have shown you that you can do from PVC pipes, as you can see the ideas of the mass, it remains only to pick up for ourselves, and slowly realize it in life.

The site "Comfort in the house" reminds its readers that we can subscribe to receiving notifications about the release of new reviews (you can subscribe to the newsletter through the form in the sidbar).

uYTVDOME.RU.

Crafts from plastic pipes for all occasions

With the skill and rich imagination, interesting and useful things can be made from any girlfriend, including plastic pipes.

Plastic pipes of different diameters are sold in any construction store at quite affordable prices. They are used in the device of water supply, sewage, heating, watering system, and after construction or repair, unnecessary trimming often clog the site, while they can serve as excellent material for creative crafts.

Do not hurry to export a construction garbage on the landfill - we will tell you what can be made from a plastic pipe to turn extra residues into beautiful and functional interior items.

What is good plastic pipe?

We will not talk about the direct appointment of the product, but about the convenience of using varieties of plastic pipes as material for crafts. Plastic pipes have light weight, durable and rather durable. They are resistant to pollution, do not collect dust and easily wash. Products made of plastic pipes are safe when exploiting even small children (do not fight, do not have heavy weight, do not emit toxins).

For creative works, PVC pipes are often used, which are quite rigid and easily connected by special nozzles and "adapters", allowing you to obtain collapsible structures. Polypropylene pipes can also be used, but for their compound, a special welding machine or compression fittings will be required, and finished goods It will not be possible to disassemble.

Methods for connecting pipes in structures

• with the help of adhesive composition;

The first method of compound is characterized by simplicity, but insufficient rigidity. Before the connection, it is recommended to clear the inner and outer surfaces of the pipes on the junction of dust particles and process the inserted part of the pipe with silicone lubricant. First, the pipe is inserted into the socket until it stops, after which it is carefully nominated by 0.7 - 1 cm. Collected in this way of construction in the future can be dismantled, which is convenient for seasonal products.

The second way of assembling pipes is distinguished by reliable fixation and greater labor intensity. Works on the connection of parts begin with the processing of the docking surfaces of the terminal and the tubes with emery paper for better clutch. Then they must be deguted with methylene chloride. The adhesive composition is applied along the entire length of the prepared outer surface of the pipe and 2/3 of the length of the inner surface of the termination. In the completion, the pipe is inserted into the socket until it stops and rotate the quarter of the turn. For gluing it is required to press the details for 1 minute. For a good fixation, all operations on the connection of two segments should be carried out quite quickly. The connected elements are left for several hours until the adhesive composition is completely drying.

The third way more time-consuming, as it requires markup and preparation of holes, but allows you to obtain collapsible structures with a reliable connection.

For angular junctions and connecting several segments at once in one node, it is convenient to use a variety of fittings. Plastic pipe structures can be any complexity using numerous tees and fittings. Consider useful homemade In ascending order of the complexity of execution.

Our review of interesting ideas opens the simplest products from a plastic pipe, to make that even novice masters of self-made art. In addition, for such crafts, the minimum amount of material will be required, and in some cases it will be possible to put even the shortest trimming.

From trimming of large and medium-sized diameter pipes, a convenient and practical organizer for the working office or workshop can be made.

Here are two versions:

• fastening with screws to the wall or table, for which one end of the cut cut at an angle is a stationary version;
• bonding segments between themselves with the formation of a stable figure - a portable option.

Additional comfort on the desktop will provide a tablet for drawing and stand for a laptop, which can be made from polypropylene pipes of small diameter.

Book shelves are a special element of the interior. Their presence in a certain way characterizes the owner of housing. The angular shelf in the style of Hi-Tech will not be ignored.

From numerous short trimming of different diameters, you can make a patterned frame for a mirror or photography. It is enough to glue the sliced \u200b\u200brings according to a predetermined layout that can be applied to a sheet of cardboard. It may be floral patterns or something abstract. Frame size will depend on quantity suitable material.

Cutting a large diameter can be used to create a comfortable shoe shelf with numerous cell compartments. Such a design will not take much space in the corridor and will ensure the storage of the shoes properly and quick search for the desired pair. The connection of the elements is carried out with the help of glue or self-tapping screws. To fix the shelf on the wall, you can use a plywood sheet to which you first glue the collected shelf.

Some crafts from PVC pipes will love to lovers of living colors. The reliable stand for colors is easy to perform and looks pretty.

Very useful for kids design - Manege from PVC pipes.

In winter walks, homemade sledges will be the most reliable and fast. The design is quite complicated, but using practical videos you can figure it out.

A glass coffee table with a base of PVC pipes on the next photo is difficult to call the amateur homemade, because it looks like design work.

Of small segments and several tees, a pretty dryer for linen and towels can be obtained. It is easily clean and is not subject to corrosion.

A carport for a car is another useful use of PVC pipes. He will protect the transport not only from the rain, but also from the scorching summer sun.

greenSector.ru.

Hands are not for boredom or crafts from plastic pipes.

With the skill and rich imagination, interesting and useful things can be made from any girlfriend, including from plastic pipes. Plastic pipes of different diameters are sold at any construction store at quite affordable prices. They are used in the device of water supply, sewage, heating, watering system, and after construction or repair, unnecessary trimming often clog the site, while they can serve as excellent material for creative crafts.

For creative works, PVC pipes are often used, which are quite rigid and easily connected by special nozzles and "adapters", allowing you to obtain collapsible structures.

From plastic pipes, not only comfortable household trivia can be made, but also furniture items. In order for such a self-made product for a long time and was securely in operation, it is necessary to take care of the correct connection of individual segments. Since the connection of polypropylene pipes has already been said, consider the dock only PVC pipes.

PVC plastic pipes can be connected in the following ways:

• in a rubber seal;
• with the help of adhesive composition;
• bolts, drump out hole.

Original and functional trifles for interior decoration

My review of interesting ideas opens the simplest products from the plastic pipe, to make that even novice masters of self-made art. In addition, for such crafts, the minimum amount of material will be required, and in some cases it will be possible to put even the shortest trimming.

1. From cropping pipes of large and medium diameters, you can make a convenient and practical organizer for the working office or workshop.

Segments can be left white or gray, but you can paint into your favorite color. Such an organizer is indispensable for schoolchildren and people engaged in creativity and needlework. With him everything will always be at hand, and on the table - the perfect order.

2. Bookshelves are a special element of the interior.

Their presence in a certain way characterizes the owner of housing. The angular shelf in the style of Hi-Tech will not be ignored.

3. From numerous short trimming of different diameters, you can make a patterned frame for a mirror or photo.

4. Cutting a large diameter can be used to create a convenient shoe shelf with numerous cell compartments.

Such a design will not take much space in the corridor and will ensure the storage of the shoes properly and quick search for the desired pair. The connection of the elements is carried out with the help of glue or self-tapping screws. To fix the shelf on the wall, you can use a plywood sheet to which you first glue the collected shelf.

5. A reliable stand for colors is easy to perform and looks pretty.

For the manufacture of flower pots under the transplantation or reproduction of indoor pets, small trimming of sewer pipes are well suited. Showing the fantasy such pots can be decorated with colored paper, paint or bright stickers.

6. Vase for artificial colors and dried flowers.

Of the elongated medium diameter cylinders, it is easy to make a stylish vase for artificial colors and dried flowers. If the embodiment of this idea approach creatively, then it can go out original gift on a significant event.

7. Techno lamps.

Another extraordinary idea for the interior is homemade techno lamps. There are a lot of performance options, but they all adhere to the principle of minimalism: no extra details.

8. Useful things to a hallway or corridor.

With the help of the assigning unused, you can also make useful things in the hallway or corridor: a hanger for clothes and bags and a trash bag holder.

9. Dryer for linen.

In addition, it is possible to make it multi-level and collapsible for more convenient and multifunctional operation.

Crafts from plastic pipes for the playground

From PVC pipes, you can make a lot of crafts for children's entertainment in the yard: a developing rug, a playpen, swing, sleds, a football gate, a gaming house, an outdoor shower and theatrical shirma.

Very useful for kids design.

11. Swing.

Children will be delighted with light swings that instantly dried after warm summer rain.

You can design not only those objects that are used in summer or indoors, but also those that are suitable for winter conditions. For example, your child will be incredibly pleased with the pretty, convenient and easy snowmobile vehicle suitable for dizzying slopes from the slide; The design is quite complicated, but using practical videos you can figure it out.

13. Football gate.

For active games in the courtyard from remnants of plastic pipes, you can make a safe football gate.

14. House - Castle.

Many children often dream of their castle in miniature. The embodiment of children's dreams are quite simple and not at all expensive. The frame is done very quickly. It will be left to choose a beautiful dense matter for roofs and walls, and the house is ready!

15. Open shower.

Refreshing in a hot summer day will help the next facility. Such an open shower will be in joy not only to children, but also adults.

16. Theatrical Shirma.

From polypropylene pipes you can make theatrical screen. It is enough to collect 3 frames, combine them between themselves and close beautifully decorated curtains. Home Theater develops creative abilities of children and creates good conditions For a fascinating pastime.

We update the interior economically: plastic pipe furniture

Crafts from plastic pipes with their own hands can occupy a key place in the interior. Folk craftsmen are divided by many extraordinary solutions, allowing to significantly save a family budget. Light the brightest of them.

17. Chair.

The most common and demanded object of furniture is a chair. Using the segments of plastic pipes and connecting elements, you can make high-quality chairs different species: Baby, folding for hike and fishing, armchairs and even chairs for feeding.

18. Bunk Baby Cot.

Slightly having mastered the equipment of the assembly, you can proceed to more complex designs. A neat bunk crib from polypropylene pipes is a good alternative for a country house or giving, when buying a finished bed is too expensive. Moreover, when the kids are growing, the material can be put on the manufacture of other useful crafts.

19. Glass coffee table.

With the base of PVC pipes, it is difficult to call the amateur homemade photo, because it looks like designer work.

20. Rack.

Another original idea is a rack for an entrance hall or living room. By independently constructing the rack with the desired amount of the shelves of the required size, you can not spend time on shopping in search of something suitable.

Useful crafts for country houses and cottages

Unused and excess building materials must be used in the country area. Crafts from plastic pipes for giving will noticeably alleviate garden workwill make rest more comfortable and help to avoid large material costs. At the same time, the structures look neat and stylish.

21. Chaise lounge.

Rest at the pool or in the garden shadow it is impossible to imagine without a lounger. The photo shows a chaise longue that is fully consisting of plastic pipes, but you can combine with dense matter.

22. Cargo for a car

Another useful use of PVC pipes. He will protect the transport not only from the rain, but also from the scorching summer sun.

23. Garden arch.

For the garden decor is often used garden archwhich can also be made of plastic pipes. A new element appears in its design - bent arcs. Bend pipes for the arched arch can be heated with gas burner or boiling water. You can also wear a pipe on a metal rod and, stuck one end to the soil, arcuately bend. This method requires certain physical efforts.

24. Gazebo.

Simple I. light Arbor Decorate the garden and protects from the sun and fine rain. For the presented version, it is sufficient to fasten the water-winding tissue on the pipes and bend them on the reinforcement rods. In order for the design to be reliable, you need to take care of the good fixation of the rods in the soil.

25. Small woodwoman, wicket, trolley or stand for fishing rod.

The spectrum of the use of plastic pipes is truly huge and limited only by your fantasy and needs. Need a small wood level, gate, trolley or rod stand - take required amount Pipes and embody your idea to life.

26. Cut for chickens.

From sewer pipes it is easy to make a comfortable feeder for chickens. It is very convenient to plunge the grain, without going into the pen. Kuras cannot be rapped in such feeders grain that saves food.

27. Greenhouse.

A small greenhouse in the country area can also be made of plastic pipes. The easiest option: make a rectangular frame and cover it with a film or agrofrix.

28. Greenhouse.

A more serious construction is a seasonal greenhouse - will require more time and material. Connect the elements better than bolts to have the ability to disassemble the design on winter. The optimal shape of the greenhouse is arched. To create it, the ends of the pipes are dressed on half-meter metal rods, driven by the sides of the future greenhouse through each meter. The size of the greenhouse depends on the planned use. The greenhouse can be installed on the foundation or ground. A film, polycarbonate or agrovolok can be used as a passing material.

29. Container for growing colors.

Plastic sewer pipes can also become a container for growing flowers, greenery and vegetables. Very often used to create vertical gardens.

To fencing the site, you can use a low fence from plastic pipes, which is distinguished by durability and minimal requirements In care (it is not necessary to paint annually).

The use of plastic pipes is not limited to the ideas presented. This material is so universal and easy to assemble (easily cuts, snacks, has a variety of connecting details), which is simply impossible to ignore it in his domestic workshop.

Regards, Aksinya.

www.livemaster.ru.

How to make a cellar in the country do it yourself