The door block is not load-bearing building element, therefore, loads from building structures should not be transferred to it. Leave a gap of at least 5 mm between the frame and the building structure.
INSTALLATION PROCEDURE
- Unpack the door frame.
- On a flat surface that prevents damage to the product, assemble the elements of the box, choosing the desired side for opening the canvas. Check that the edges of the crossbar and the pillars are in the same plane, and at the place of their contact the gap does not exceed 1 mm. Drill four through holes on the back side of the crossbar, then connect the frame elements with self-tapping screws. For a self-tapping screw 4.2 x 70 we recommend a drill with a diameter of 3.5 mm.
- Insert the frame into the doorway and secure with wedges (at least three points on each side).
- Using a level, secure the hinge post strictly vertically using a hammer drill and mounting screws, using spacers between the opening and the frame at the fastening points.
- Loosen the hinge fastening screw and hang door leaf.
- Close the blade, and install the stand on the side of the lock so that the blade fits along the entire perimeter, providing an even gap, and secure the stand in this position.
- Open and close the blade several times, making sure that it is installed correctly and that nothing interferes with closing. Right installed door(when it opens 45°) should not open or close spontaneously.
- Finally secure the hinges to the screws and install the fittings.
- Fill the installation gap between the box and the wall with low-expanding polyurethane foam (when using foam, follow the manufacturer's instructions).
- It is recommended to install the casing only after the mounting foam has completely dried. During the drying period of the foam (about 12 hours), the door should be kept closed at all times.
CHANGING THE SIDE OF THE CANVAS
A blind canvas of standard height is available for both right and left. This is achieved due to the vertical symmetry of the canvas.
To change the door opening direction:
- unscrew the fastening screws and pull the lock body out of the door, turn it 180° (so that the lock tongue is on top, above the bolt), install the lock back in this position;
- Using pliers, pull the bolt out of the lock body by 3 mm and turn it 180°.
Tools required for installation: screwdriver with a set of bits, hammer drill or impact drill, level, wood saw, measuring tape.
Before installing external doors, carefully read the installation instructions. JELD-WEN is not responsible for product defects resulting from improper storage, use or installation.
Storage
Check the product immediately upon receipt! An incorrect or defective product is not suitable for installation!
Doors should be stored in a well-ventilated area inside the building on a horizontal and level surface. Avoid scratches and other mechanical damage!
Do not store the doors in a place where direct sunlight penetrates, in a heat-free or damp room, on the ground or concrete, but should be laid on a hard, level and dry surface.
Exterior door installation
The door must be installed in such a way that it is not directly exposed to heavy rain and solar radiation. The door must be installed in a niche located in the wall or a canopy must be placed over the door.
- Dark-colored doors may become warped and dull when exposed to intense sunlight.
- Changing the dimensions of the product, making cuts and repainting is not allowed. If necessary, consult your factory representative.
- During installation and repair work the door must be protected with construction cardboard or film to avoid damage during finishing.
- Protect the door (eg film or paper) during finishing works on site until complete completion! When using adhesive tape to secure film or paper, be careful not to let the adhesive side of the tape stick to the door or frame.
Tools required: moisture guard, hammer, saw, screwdriver, levels (500 mm and 2000 mm), angle, drill, mounting wedges, pencil, tape measure, hex wrench, insulating wool and sealant.
Entrance doors are supplied as a set - the frame is mounted with a threshold and the door is hung on hinges.
Before you begin installation, make sure the quality of the product and its contents:
- Door leaf
- Door frame
- Hinges, lock body, striker plate
- Threshold
- Seals, plugs for mounting holes
- Installation instructions. Warranty conditions.
Installation of FUNCTION and Classic exterior doors and balcony doors
|
Place the door kit on the base with the opening side down! Open the package from the edge (from the outside of the box to avoid possible appearance scratches on exterior decoration)! Separate the box from the canvas! Separate the box from the canvas! |
|
|
Also check that the vertical and horizontal sides of the box are straight! |
 |
 |
|
 |
|
 |
|
 |
|
 |
|
 |
|
 |
|
|
Entrance doors can be adjusted in height and horizontally. AdjustmentByheight - adjustmentdoorsup
Height adjustment - door adjustment downwards
Horizontal adjustment - reducing the distance between the door and the door frame on the hinge side
|
 |
| Install plugs on the mounting holes. Install the lock and handle. |  |
| To fill the gap between the frame and the opening, use insulation materials(glass wool, mineral wool or polyurethane foam). You can fill the gap between the threshold and the floor with silicone. |  |
|
Install the front door in a niche or under a canopy. The minimum canopy should be 70 mm wide, but when installed front door with glazing, we recommend using a canopy with a minimum width of 500 mm. |
 |
 |
BASIC entrance door installation
Before installing the door, check whether it matches the size of the doorway and whether the opening is even and has right angles. Doorway should be 15 - 45 mm larger than the external dimensions of the box. Adjust it if necessary. Also check that the base under the threshold is horizontal and rigid.
|
Place the door kit on the base with the opening side down! Open the package from the edge (from the outside of the box to avoid possible scratches on the exterior)! Separate the box from the canvas! |
 |
|
Check that the base under the threshold is horizontal and stable! Attach the threshold to the floor using silicone! Also check that the vertical and horizontal sides of the box are straight! |
 |
| To secure door frame choose special fastening hardware! You can use screws with wedges or sleeves. When using sleeves, you do not need wedges. |  |
|
Secure the hinge side of the box first and then the lock side! The gaps between the box and doorway can be maximum 20 mm. Check if the box is straight! |
 |
| Choose mounting hardware according to the wall material! |  |
| If you use sleeves, then mounting wedges will not be needed, since the sleeve allows you to adjust the distance of the frame from the doorway. |  |
| Check that both the vertical and horizontal sides of the box are straight! |  |
| Hang the door on its hinges! To do this, loosen the bolt a little, hang the door and tighten the bolt. Then screw the hinges using screws! Make sure that the corner of the door does not touch the floor! Impact may damage the finish! |  |
| Close the door and make sure that the door leaf (especially the corners on the lock side of the frame) is flush with the frame! |  |
|
If necessary, adjust the position of the doors using the hinges! Height adjustment
Lateral adjustment
|
 |
| Cover the mounting holes with plastic plugs! |  |
| Fill the space between the threshold and the floor with silicone! Add blocks if necessary! |  |
| Install the front door in a niche or under an awning. The minimum canopy should be 70 mm wide, but when installing an entrance door with glazing, we recommend using a canopy with a minimum width of 500 mm. |  |
|
Using strips of insulating wool, fill the gap between the frame and the wall opening so that the strip of wool leaves a free space of 10-20 mm to the outer edge of the box. WITH inside boxes, use glue to glue the insulating wool to the box! WITH outside do not use glue boxes! Install platbands! |
 |
| Adjust the screws that hold the strike plate in place so that the door closes tightly! |  |
Instructions for caring for external doors
- If the door is not damaged or badly worn, then light cleaning with ordinary detergents (not alkaline) is sufficient. To ensure that the door retains its shine, you can treat it with car wax once a year after cleaning. This also makes subsequent cleaning easier. Cleaning with abrasives and solvents is prohibited.
- Clean veneered external doors with a dry and clean cloth. It is advisable to re-oil the door leaf and frame once a year. For this purpose, use colored oils intended for use in external conditions (when oiling, read the instructions included with the product).
Follow the instructions, be precise with measurements and check the results. Please read the instructions carefully before proceeding with installation. The external door is intended primarily for use as an entrance door in private houses for year-round use, mansions and townhouses, in such buildings where thermal insulation qualities are required.
It is strictly forbidden to install doors in a house under construction or in a room where construction is taking place. wet work(for example, concreting a floor, pouring screed, etc.). Excessive moisture can cause wood to warp and paint to peel. In addition, the fittings, including the lock body, may become rusty.
ATTENTION! When installing entrance doors in the cold season, it is necessary to use certified mounting foams specifically designed for use in low temperatures- information with specific recommendations for use is usually printed on the cylinder by the manufacturer.
Always install moisture barrier (bitumen strip, etc.) between the horizontal base and the threshold.
Never install the box directly on a concrete floor or screed! Use, for example, bitumen strip, etc.
Doors should be installed in places with a sufficiently long roof overhang or canopy over the door, which will protect the door surface from moisture and sunlight.
When determining the size of the canopy, you should be guided by the following formula: the width of the canopy D must be at least half of the height of the canopy (the distance from the bottom of the door to the bottom of the canopy, see diagram).
Entrance door installation steps:
Stage 1
Check that the base under the threshold is horizontal.
Install the ebb in the mounting opening and place the assembled box on it
Coat the seam with sealing compound.
Low tide can be installed later. In this case, bring the ebb tide under the threshold
and glue it, installing the ebb in the groove intended for it in the threshold.
Stage 2
Secure the box in the mounting opening using wedges, inserting them above the mounting holes of the box so that the side of the box with hinges is exactly vertical (both parallel and prependicular to the plane of the wall). Use two wedges for each mounting hole in the box, insert one wedge from the outside, the other from the inside. Use a spirit level to check that the box is level.
Make sure there is enough space around the perimeter of the box for the seal
and secure the hinge side of the box to the wall with mounting screws.
Stage 3
Install anti-burglary pins in the door. Do not screw them in completely, leave a margin of 10mm. Hang door leaf on the hinges.
Tighten the anti-burglary pins as far as they will go, install and tighten the hinge mounting screws.
Stage 4
Make sure the threshold is set horizontally. Align the side of the box with the lock strike plate exactly (both parallel and prependicular to the plane of the wall). Secure the box to the wall with mounting screws.
Stage 5
To adjust the door height, use a hex key. Before adjusting the door sideways, loosen the security pins and mounting screws. Adjust to the side using the adjusting screw provided for this purpose. After adjustment, tighten the anti-burglary pins and mounting screws as far as possible.
Adjusting the hinges of the Jeld-Wen entrance door
Blade position outer door can be adjusted in height and horizontally using the hinge adjustment.
This is especially true, for example, when shrinking a house.
Height adjustment
Tools required: 5 mm hex wrench.
Door adjustment up
- Loosen the upper adjusting screw (1) on all hinges by turning it 2-3 turns with a hexagon.
- By turning the adjusting screws (2) on the bottom of the hinges, set the door to the desired height position.
- Be sure to tighten the screws on all hinges an equal number of turns to evenly distribute the weight of the door on the hinges.
- Tighten the retaining screws on top of all hinges (1).
Door adjustment down
- Loosen the lower adjusting screw (2) on all hinges except one by 2-3 turns.
- By turning the screw (2) of the remaining hinge counterclockwise, lower the door to the desired height.
- Tighten the adjustment screws (2) of the remaining hinges to the same position to evenly distribute the weight of the door across all hinges.
- Finally, tighten the upper adjustment screws (1) without excessive force.
Horizontal door adjustment
Tools required: 5 mm hexagon, Phillips screwdriver.
Increasing the distance between the door and the door frame on the hinge side
- Tighten the adjusting screws (4) on one of the hinges so that the door leaf is in the desired position. .
- Tighten the adjustment screws (4) on the second hinge (on the remaining hinges) to level the door leaf and distribute the weight of the door evenly.
Reducing the distance between the door and the door frame on the hinge side
- Loosen the mounting screws (3) and the anti-removal pin (5) on all hinges by 2-3 turns.
- Loosen the adjusting screws (4) on one of the hinges so that the door leaf is in the desired position. .
- Loosen the adjustment screws (4) on the second hinge (on the remaining hinges) to level the door leaf and distribute the weight of the door evenly.
- Carefully tighten the screws (3) and anti-removal pins (5).
Stage 6
Does the door close tightly?
The closing tightness can be adjusted using adjustments in the strike plate.
Stage 7
Carefully seal the gap between the wall and the frame, filling it mineral wool. Then coat the gap with a sealing elastic mass to vapor-waterproof the seam. Do not use polyurethane foam, because when it expands, it can deform the door frame and complicate possible subsequent door adjustments.
Instructions for servicing external doors
Painted products
The products are painted with moisture-resistant paints that meet the requirements for resistance to scratches, wear resistance and appearance surfaces that can withstand exposure to many household chemicals, grease and solvents.
Cleaning
Use regular ones detergents(non-alkaline), such as dishwashing liquid. To clean mold, use special means to remove mold. Do not use detergents that may scratch or dissolve the painted surface. Avoid, for example, the use of solvents, abrasive powders, metal fiber sponges, etc. Wet the surface from bottom to top, but wash it from top to bottom. Otherwise, streaks from drips may appear on the door. Wipe dry.
Service
Normal cleaning is usually sufficient unless the door is damaged or abnormally worn. To maintain shine, however, it is recommended, after washing, to rub the door surfaces, for example, with car wax.
Touch up
It is best to touch up minor damage with a brush and alkyd or acrylate enamel of a suitable color and gloss level, intended for outdoor use. First check the compatibility of the paint with the original painting material on a small surface, e.g. small area on the edge of the door on the hinge side.
Product quality and warranty conditions for Jed-Wen doors
Jeld-Wen manufactures its products in accordance with the requirements of the unified European standard CE.
What is CE?
The CE mark is a guarantee to the consumer that a given product complies with the essential requirements of a European harmonized standard and can therefore be legally placed on the market.
CE marking has long been mandatory on products such as toys and electronics, but Lately, this unified standard is established for certain building materials.
What does this mean for the consumer?
All CE marked products carry product data in the Declaration of Performance (DoP) format, allowing clear and easy comparisons between similar products and providing the consumer with the information they need to make an informed decision.
The DoP provides key information on the performance characteristics of construction products that have been independently tested and certified by an EU body.
All products subject to these Directives are required to be marked with the CE mark, either on the product itself or on its packaging - the CE logo and a number which indicates the relevant DoP.
Failure of the product to comply with the requirements of the CE standard in terms of curvature of the blade or frame is considered a warranty defect.
We apologize if you encountered a defect in JELD-WEN products! If you find a defect, please contact us and provide your order number. Please note that a defective product cannot be installed or used!
How to measure whether a door leaf is curved?
Place the door leaf on a flat horizontal surface
Measure the distance between the central part of the door leaf and the surface on which it is located (mm)
Allowed curvature of up to 5 mm per door leaf
How to measure if a door frame is warped?
Curvature towards the wall
Place the box (flat) on a horizontal flat surface so that the ends of the box touch the ground.
The allowed curvature of the box in the direction of the wall is 3 mm / per 1 meter (i.e. for a box with a height of 20M and 21M 6 mm per vertical of the box.
Curvature towards the edge of the box
Place the box on its side on a flat, horizontal surface with the ends of the box touching the surface.
Measure the gap between the center of the box and the surface (mm).
The allowed curvature of the box in the direction of the edge is 1.5 mm / per 1 meter (i.e. for a box with a height of 20M and 21M up to 3 mm per one of its verticals)
We are not responsible for product defects resulting from normal wear and tear, improper storage, installation and operation.
Follow the instructions, be precise with measurements and check the results. Please read the instructions carefully before proceeding with installation. The external door is intended primarily for use as an entrance door in private houses for year-round use, mansions and townhouses, in such buildings where thermal insulation qualities are required.
It is strictly forbidden to install doors in a house under construction or in a room where wet work is being carried out (for example, concreting a floor, pouring screed, etc.). Excessive moisture can cause wood to warp and paint to peel. In addition, the fittings, including the lock body, may become rusty.
ATTENTION! When installing entrance doors in the cold season, it is necessary to use certified mounting foams specifically designed for use at low temperatures - information with specific recommendations for use is usually printed on the bottle by the manufacturer.
Always install moisture barrier (bitumen strip, etc.) between the horizontal base and the threshold.
Never install the box directly on a concrete floor or screed! Use, for example, bitumen strip, etc.
Doors should be installed in places with a sufficiently long roof overhang or canopy over the door, which will protect the door surface from moisture and sunlight.
When determining the size of the canopy, you should be guided by the following formula: the width of the canopy D must be at least half of the height of the canopy (the distance from the bottom of the door to the bottom of the canopy, see diagram).
Entrance door installation steps:
Stage 1
Check that the base under the threshold is horizontal.
Install the ebb in the mounting opening and place the assembled box on it
Coat the seam with sealing compound.
Low tide can be installed later. In this case, bring the ebb tide under the threshold
and glue it, installing the ebb in the groove intended for it in the threshold.
Stage 2
Secure the box in the mounting opening using wedges, inserting them above the mounting holes of the box so that the side of the box with hinges is exactly vertical (both parallel and prependicular to the plane of the wall). Use two wedges for each mounting hole in the box, insert one wedge from the outside, the other from the inside. Use a spirit level to check that the box is level.
Make sure there is enough space around the perimeter of the box for the seal
and secure the hinge side of the box to the wall with mounting screws.
Stage 3
Install anti-burglary pins in the door. Do not screw them in completely, leave a margin of 10mm. Hang the door leaf on its hinges.
Tighten the anti-burglary pins as far as they will go, install and tighten the hinge mounting screws.
Stage 4
Make sure the threshold is set horizontally. Align the side of the box with the lock strike plate exactly (both parallel and prependicular to the plane of the wall). Secure the box to the wall with mounting screws.
Stage 5
To adjust the door height, use a hex key. Before adjusting the door sideways, loosen the security pins and mounting screws. Adjust to the side using the adjusting screw provided for this purpose. After adjustment, tighten the anti-burglary pins and mounting screws as far as possible.
Adjusting the hinges of the Jeld-Wen entrance door
The position of the outer door leaf can be adjusted in height and horizontally by adjusting the hinges.
This is especially true, for example, when shrinking a house.
Height adjustment
Tools required: 5 mm hex wrench.
Door adjustment up
- Loosen the upper adjusting screw (1) on all hinges by turning it 2-3 turns with a hexagon.
- By turning the adjusting screws (2) on the bottom of the hinges, set the door to the desired height position.
- Be sure to tighten the screws on all hinges an equal number of turns to evenly distribute the weight of the door on the hinges.
- Tighten the retaining screws on top of all hinges (1).
Door adjustment down
- Loosen the lower adjusting screw (2) on all hinges except one by 2-3 turns.
- By turning the screw (2) of the remaining hinge counterclockwise, lower the door to the desired height.
- Tighten the adjustment screws (2) of the remaining hinges to the same position to evenly distribute the weight of the door across all hinges.
- Finally, tighten the upper adjustment screws (1) without excessive force.
Horizontal door adjustment
Tools required: 5 mm hexagon, Phillips screwdriver.
Increasing the distance between the door and the door frame on the hinge side
- Tighten the adjusting screws (4) on one of the hinges so that the door leaf is in the desired position. .
- Tighten the adjustment screws (4) on the second hinge (on the remaining hinges) to level the door leaf and distribute the weight of the door evenly.
Reducing the distance between the door and the door frame on the hinge side
- Loosen the mounting screws (3) and the anti-removal pin (5) on all hinges by 2-3 turns.
- Loosen the adjusting screws (4) on one of the hinges so that the door leaf is in the desired position. .
- Loosen the adjustment screws (4) on the second hinge (on the remaining hinges) to level the door leaf and distribute the weight of the door evenly.
- Carefully tighten the screws (3) and anti-removal pins (5).
Stage 6
Does the door close tightly?
The closing tightness can be adjusted using adjustments in the strike plate.
Stage 7
Carefully seal the gap between the wall and the frame by filling it with mineral wool. Then coat the gap with a sealing elastic mass to vapor-waterproof the seam. Do not use polyurethane foam, because when it expands, it can deform the door frame and complicate possible subsequent door adjustments.
Instructions for servicing external doors
Painted products
The products are painted with moisture-resistant paints that meet the requirements for resistance to scratches, wear resistance and surface appearance, and which withstand exposure to many household chemicals, grease and solvents.
Cleaning
Use regular detergents (non-alkaline), such as dishwashing liquid. To clean mold, use special mold removers. Do not use detergents that may scratch or dissolve the painted surface. Avoid, for example, the use of solvents, abrasive powders, metal fiber sponges, etc. Wet the surface from bottom to top, but wash it from top to bottom. Otherwise, streaks from drips may appear on the door. Wipe dry.
Service
Normal cleaning is usually sufficient unless the door is damaged or abnormally worn. To maintain shine, however, it is recommended, after washing, to rub the door surfaces, for example, with car wax.
Touch up
It is best to touch up minor damage with a brush and alkyd or acrylate enamel of a suitable color and gloss level, intended for outdoor use. First check the compatibility of the paint with the original paint material on a small area, for example, by painting a small area on the edge of the door on the hinge side.
Product quality and warranty conditions for Jed-Wen doors
Jeld-Wen manufactures its products in accordance with the requirements of the unified European standard CE.
What is CE?
The CE mark is a guarantee to the consumer that a given product complies with the essential requirements of a European harmonized standard and can therefore be legally placed on the market.
CE marking has long been mandatory on products such as toys and electronics, but more recently this unified standard has been established for certain building materials.
What does this mean for the consumer?
All CE marked products carry product data in the Declaration of Performance (DoP) format, allowing clear and easy comparisons between similar products and providing the consumer with the information they need to make an informed decision.
The DoP provides key information on the performance characteristics of construction products that have been independently tested and certified by an EU body.
All products subject to these Directives are required to be marked with the CE mark, either on the product itself or on its packaging - the CE logo and a number which indicates the relevant DoP.
Failure of the product to comply with the requirements of the CE standard in terms of curvature of the blade or frame is considered a warranty defect.
We apologize if you encountered a defect in JELD-WEN products! If you find a defect, please contact us and provide your order number. Please note that a defective product cannot be installed or used!
How to measure whether a door leaf is curved?
Place the door leaf on a flat horizontal surface
Measure the distance between the central part of the door leaf and the surface on which it is located (mm)
Allowed curvature of up to 5 mm per door leaf
How to measure if a door frame is warped?
Curvature towards the wall
Place the box (flat) on a horizontal, flat surface so that the ends of the box touch the ground.
The allowed curvature of the box in the direction of the wall is 3 mm / per 1 meter (i.e. for a box with a height of 20M and 21M 6 mm per vertical of the box.
Curvature towards the edge of the box
Place the box on its side on a flat, horizontal surface with the ends of the box touching the surface.
Measure the gap between the center of the box and the surface (mm).
The allowed curvature of the box in the direction of the edge is 1.5 mm / per 1 meter (i.e. for a box with a height of 20M and 21M up to 3 mm per one of its verticals)
We are not responsible for product defects resulting from normal wear and tear, improper storage, installation and operation.
Finnish doors began their victorious march across the expanses of the post-Soviet countries at the end of the last century. People began to trust what could be behind the low price high quality. White paneled doors from Finnish manufacturers, who continue to not only maintain, but also expand the niche of their products, are familiar to everyone. Most people want to have strong, reliable, comfortable and durable doors.
Finnish doors began their victorious march across our country more than 10 years ago. Environmentally friendly application pure materials and the most modern technologies, allows us to produce high-quality and high-quality products designed for a long service life without losing their consumer qualities.
The range and color range of Finnish doors currently supplied are so wide that they can satisfy the most sophisticated taste of the buyer. This interior doors, doors for saunas, doors for bathrooms, fire doors, entrance doors and others.
Despite this diversity, interior doors are still in greatest and most consistent demand. Previously, the overwhelming majority of Finnish interior doors supplied to our country were smooth frame doors with honeycomb filling or paneled doors made of solid pine. Usually such doors were white or gray. Now veneered and melamine doors have been added to them. Veneered doors are finished with veneer of valuable wood species - oak, beech, hornbeam, mahogany. Melamine doors are covered with melamine, which imitates the veneer of certain types of wood - walnut, cherry, pear, etc.
All types of Finnish doors have one distinctive design feature, which distinguishes them favorably from the bulk of other doors. This is the presence of a flap or a special protrusion on the door leaf that closes the gap between the leaf and the door frame. This design makes it possible to improve the heat and sound insulation of Finnish doors. In addition, the protrusion of the door leaf makes possible flaws during installation invisible.
The set of interior doors includes a door frame with embedded hinges and a door leaf with installed mortise lock, which allows you to minimize damage that occurs during the installation of doors.
Finnish interior doors are adapted to Russian conditions. Due to the thickness of the door frame of 92 mm, they are suitable for installation in any interior partitions. The height of the door frame of Finnish doors is 210 mm, which exceeds the Russian standard by several centimeters. Therefore, sometimes it becomes necessary to trim the door a little.
Before purchasing Finnish interior doors, determine which doors you need - left or right. If door hinges located to your left - this is the left door. These doors have left-handed locks. And if the door hinges are on the right, then these are right-handed doors with a right-hand lock. You must be in the room into which the door opens.
Installation of Finnish doors.
The door block consists of a frame and one- or two-door leaves. By design and functional purpose doors are divided into panel and frame, external, internal, balcony, etc., with and without a threshold, with and without a transom, glazed and solid...
Panel doors consist of a frame, filling and sheathing. Frame completed made of timber (slats), cladding - from glued plywood, veneer, solid fiberboards, filling - from small-sized lumber, waste plywood and hardwood fiberboard, paper honeycomb. foam plastics, etc. The door leaf is framed along the perimeter with wooden trims.
Frame doors (panelled, framed) consist of frame (bars) and filler (panels). Glass, boards, plywood, fiberboard and particle boards can be used as panels.
According to the design of the door leaves, doors are divided into single-leaf, double-leaf with leaves of the same and different widths, and according to the opening method - on the right with the door leaf opening counterclockwise and on the left with the door leaf opening clockwise.
Front and interior doors can be solid or glazed. Often the upper part (transom) of door blocks is glazed and fixed tightly in the frame, or glass is inserted into the door instead of panels.
You can design the door yourself, order it from a craftsman, or purchase it in a store. More durable doors are made of oak or beech, more beautiful ones are made of mahogany or ash.
Installation of door frames and doors. When installing the door frame of the front door, the block is lifted and installed in the opening on a lining made of roofing felt and mastic. Recently, the door frame is most often installed on polyurethane foam. It is necessary to ensure that the lower bar occupies a strictly horizontal position. Vertical and horizontal elements are installed using a square, plumb line and level. The plumb line must pass exactly through the middle of the top side and the intersection of the diagonals of the box. The absence of distortions during installation is evidenced by the equality of the diagonals. This can be achieved using wedges, lifting one side or another of the box. After leveling vertically and horizontally, the box is attached to the wall at three points on each side: at a distance of 1 m from the floor and 30 cm from the top and bottom of the box. They drill or punch holes in the wall (against the side of the box) and hammer wooden plugs into them to a depth of 40-50mm. install the box and drive nails into the corks, the heads are recessed into the wood by at least 2 mm. Instead of nails, you can use steel pins with a diameter of 8-10 mm; the diameter of the holes for them should be 2-3 mm less than the diameter of the pins.
The gaps when installing between the wall and the frame are caulked with dry or wet method. With the dry method, the gaps are filled with dry tow, slag or glass wool and sealed. When wet, the materials are moistened in gypsum dough (it is prepared in small portions - from 0.2 to 0.5 l). As it hardens, wet plaster expands and presses more tightly against the wall and beam, protecting the gap from blowing through.
When installing, the frame of a paneled external door is made of simple and shaped bars. Kalevki are selected on a harness or on separate bars. They form a groove 15-20mm deep. where panels up to 50 mm thick are inserted.
Internal doors, depending on their purpose, can be solid or lattice. Frames for internal doors are less massive and consist of three bars - two vertical and an upper one. When installing doors in interior walls openings are made without quarters. The door frame in the partitions is pulled out to one side of the doorway to the thickness of the plaster so that during installation the platband is adjacent to the frame and the wall. When the thickness of the partition is less than the width of the door frame, nail a block with a thickness equal to the difference in the thicknesses of the partition and frame. If the thickness of the partition is greater than the width of the door frame, a block of appropriate thickness is nailed to the inside of the frame.
If, during installation, you additionally connect the door bars with dowels (wooden pins), the door becomes stronger. The diameter of the holes for the dowels is 10-15mm. Pins are made from wood hard rocks. The dowels are fastened using glue.
The doors are installed on hinges selected according to size. Most often, two hinges are installed on the door leaf, but in some cases, when the door is made of heavy wood, three hinges are installed. Under no circumstances should hinges be installed on the horizontal bars of the door trim.
Binders and doors are hung on hinges different designs, more often - half-hinged and hinged. Half-hinged hinges consist of two card halves; in one a rod or axis is attached, in the other a hinge in the form of a cap is attached. Such loops are always removable; their cards can be easily separated. To reduce friction between them, a ring is put on the rod, usually bronze (can be copper or brass). Each card has three to four holes for screws (a hinge has six to eight holes), and sometimes more. The height of such loops is 75-50 mm, the width of the card is 30-45 mm.
Hinge hinges are made blind and removable; the latter have a tip screwed onto one end of the rod. The height of the loops is 75-25 mm, the width of the card is 30-35 mm. Binders and doors are installed on such hinges. Hinge hinges of smaller sizes are used for vents. The dimensions of the loops are determined based on the massiveness of the products, the sizes of the bars of the boxes and straps.
The screw shaft should fit fairly tightly into the hinge hole, and its head into the countersunk hole. When the head of the screw protrudes above the countersunk hole, the doors will spring back and not close tightly.
When installing, screws with flat or countersunk, semicircular or semi-countersunk heads are used: the first type of screws is for all types of work, the second and third are for fastening handles, add-on locks and other devices, that is, where the protruding heads will not interfere with the tight rebate of the sashes door frames.
When installing or replacing collapsible hinges, you must remember that the hinges can be left-handed or right-handed - they are not interchangeable. New loops should have the same direction as the old ones.
When installing, to determine the direction of the door, you need to open it towards yourself - the door will be left-handed or right-handed, depending on which hand is on the door handle. There is a rule that makes it easier to remember: the right door opens counterclockwise.
The work of installing hinges is carried out in the following sequence: the hinge is placed against the sash or door at a distance from the edge equal to the length of the hinge. Mark the places for the loops. Using a chisel, cut wood to the thickness of the hinge card and attach it with screws so that its axis is parallel to the edge of the block. Having secured the hinges on the sash or door, they are opened, placed against the box, pressing tightly against the top bar, and outlined according to the open cards, leaving marks for the hinges on the quarters. Based on the risks, select the wood for the hinge maps, mark the locations for the screws, install each hinge with one screw, and check how the sash or door closes. If necessary, make corrections and strengthen the hinges with screws.
When installing doors in a frame, it is especially important to fit the door to the quarter. A hung door should not spring when opening and closing, but should rotate freely on its hinges.
The handles are also secured with screws. The gaps between the door frames and the wall are covered with slotted boards.
After installation door block the canvas is removed from the hinges so as not to damage it during finishing work. Upon completion of the finishing of the room, door blocks in the openings of plastered walls and partitions are lined with platbands at the level of the wall plane.
Installation ready-made kit. A door set usually consists of three elements: a door leaf with a built-in lock and latch, a door frame with a door stopper and hinges, and trims fitted to a miter joint. Finnish doors have a strong reputation in our market; they are seriously competed by French products, which has a special grace.
Modern interior door can be made of chipboard or fibreboard, aluminum and plastic (PVC), etc. Door frames are also made of different materials.
In a finished door kit, the hardest work is done at the factory. The jambs and lintels are profiled and drilled for assembly. The doors have hinges installed and the lock is in place. All that remains is to assemble the components and install the kit in a new doorway or in an old opening from which the door and frame fastening have been removed. The assembly principles are the same for all door sets. The difference lies in the completeness of the assembly of the supplied package. The box may be a set of individual elements, separate platbands, or maybe it’s all already assembled.
Before starting, measure the height and width of the opening, as well as the thickness of the wall. Door frames are supplied in sets depending on the wall thickness. Before installation, you need to decide which side of the wall the door will open to and whether it will open to the left or to the right. It is very important when installing a door block - and this depends on your qualifications - to place the frame correctly in the doorway. If the frame is slightly skewed or does not fit tightly into the opening, the door will not open and close correctly. And you are unlikely to be able to install the door without damaging its appearance. So, you need to start from the loop side of the box. If you installed this jamb correctly and fit it tightly, then install top bar and the opposite jamb is not at all difficult.
The canvas, platbands and parts of the frame facing the room have already been finished (paint, varnish, veneer, etc.), but the wood facing the inner edge of the opening is usually not processed.
The door frame is assembled as follows: first, connect three sections of the door frame and door casing, passing the plastic tenons on the jambs into the plastic grooves on the lintel. Then press the components together until their corners connect correctly. The box is fastened by inserting bolts into drilled holes and tightening them with nuts.
After this, the assembled box is placed in the doorway. The spaces between the jambs and the wall should be the same on both sides. The platband is pressed tightly against the wall. Using a plumb line or level, make sure that the hinge jamb is plumb and does not deviate to the side.
Working from the other side of the doorway, insert the seal between the hinge jamb and the wall at the level of all three hinge pins. Holes are drilled in the untreated surface of the hinge jamb at the level of each hinge. If the wall is concrete or brick, then drill the wall and insert plugs into the holes. Then install the jamb to the wall with No. 10 screws. The screws must be long enough to grip the jamb, seal and penetrate the wall at least 25 mm
Doors are hung as follows: the door is lowered at right angles to the plane of the opening with three hinge sockets screwed to the door onto the corresponding hinge pins of the jamb. Install handles and handle caps on both sides of the door, close the door, adjust the position of the loose jamb, and then insert weather stripping between the jamb and the wall. The second jamb is secured to the wall in the same way.
In order to cut the trim to size, the inner edge of one of its sections is inserted into the corresponding groove door stopper boxes. If a gap forms between the platband and the wall, then the surface of the platband is adjusted with a plane.
Do the same with other sections.
The platbands are strengthened during installation as follows: three sections of the platbands are connected in the same way as the sections of the box; spread with the necessary glue (PVA, assembly adhesives Liquid, Nails, Dap, the Nail, etc.) the raw surface of the frame along the jambs and lintel, then push the assembled trim into the door frame. When installing, the inner sides of the platband are firmly pressed against the groove assembled box. Cut three spacers from a block (or boards) the width of the doorway. It is necessary to place a soft cloth under the ends of the bars so as not to damage them. varnished surface platband Then spacers are wedged between the sections of the casing lubricated with glue. This will hold the trim securely in place until the glue dries.
Entrance and interior doors. Finnish doors
Finnish doors have been quite popular for many years. Previously, they were only available to some people. But now they can be found absolutely everywhere: in cafes, restaurants, in apartments. These doors have already managed to occupy a certain niche of this market and study the Russian consumer.
Finnish doors have managed to show that they are very reliable and of high quality. They worked on the manufacturing technology of these doors for a very long time. And this brought the production of Finnish doors to a new - European level. They became sold in all countries.
One of the differences between Finnish doors is their strict design in a palette with fairly cool shades. The abundance of different models allows each buyer to find what he needs. But some people don't want to buy Finnish doors because they think their design is a little "stingy".
The most important advantage ahead of other doors is the ease of installation. All required holes made by the manufacturer itself. The width of the door frame is 9 cm, the height is 210 cm. These parameters are suitable for Russian apartments, although sometimes you have to trim the door a little or increase the opening itself.
If you decide to give preference to purchasing Finnish doors, then when purchasing you need to look at the certificate of conformity issued to the manufacturing company and whether it has a corresponding seal and a stamp on the end of the door itself.
- Price and Quality are current
Have you decided to buy interior doors? then think about a few things: the price that suits you, the right option door opening, design, dimensions and the presence of additional doors similar in design to doors.
It wouldn’t hurt to immediately think through the design of the doors. It is necessary to take into account that Sami wooden doors are expensive, but at the same time, they can become a real decoration of the interior. The elegance, variety of shapes and service life of such doors (massive doors can be repaired) speaks for itself. If your goal is to buy interior doors that are durable and flawless in operation, you need to know the manufacturers’ strict adherence to all cycles technological process during their manufacture. The quality of the materials used by the craftsmen also plays an important role. To mark high quality, some companies put their logo on the product. 
Interior doors made from combined materials, such as MDF. They look great, are durable and are virtually equal in quality wooden door. But the plus is that their reaction to changes in humidity in the room is much less. The price of an MDF door depends on the type of veneer wood used for finishing. At the same time, the type of material does not affect the quality of the door itself; it gives the door leaf a shade and texture.
There are also hollow, so-called honeycomb filling, doors. The outer panel is specially formed. Such as masonite interior doors are less durable and require more careful operation. They exist both already covered with veneer, and simply in a primed form. The latter are suitable for people with more creative approach, because they allow you to paint the interior as you like.
The door frame can be made from either solid wood or chipboard or MDF. It is wood, despite its popularity among buyers, that is less practical. The array can become damaged over time, and there is also a risk of changes in linear dimensions. Modern materials, made to look like wood, not only exceed physical properties array, but also in appearance, sometimes superior natural wood. At the same time, the technology for installing boxes of different materials will be completely different.
Certification is not provided for interior doors. And it is quite difficult to determine the quality of the material from which the door leaf is made by eye. Experts recommend buying a door from trusted, serious companies, or from an already established and proven brand.
Processed