Tired of a puddle under a pipe? How to minimize the formation of condensation on water pipes. The cold water pipe is leaking! Solution to the problem

A rare person has not had to deal with such a phenomenon as condensate on the surface of the pipeline cold water. Although this unpleasant phenomenon can also occur on other structures - windows, external walls, in the corners of rooms.

Condensation is caused by moisture vapor in the air. In contact with a cold surface, they cool down and turn into drops. The higher the humidity in the room and the greater the temperature difference between the air and the cold surface, the greater the likelihood of this unpleasant phenomenon.

If pipes and windows are chronically “crying” in the house, then it is urgent to deal with the causes of this phenomenon.

Mostly this affects areas such as bathrooms and toilets. It is there that the risers of cold and hot pipelines are usually located.

There are several reasons for water condensation on pipes:

• poor ventilation of the bathroom and toilet, leading to the preservation of high humidity and an increase in the overall temperature in these rooms;
• in the toilet, the cause of the problem can be a malfunction of the valve that shuts off the water in the toilet bowl - water leakage leads not only to its leakage, but also to the constant cooling of the pipe with cold water;
• in the bathroom, condensate often forms for the same reason - a malfunction of the faucet valve that shuts off cold water;
• high humidity in an apartment or house, which can be caused by many malfunctions - poor ventilation, current roofing, incorrectly selected insulation.

If condensation began to form recently, then the cause must be immediately clarified, and not wait until the problem becomes chronic. Perhaps you have recently changed windows or installed some kind of equipment in the house that contributes to the “warming of the microclimate”.

It must be remembered that although condensate is just water, it is it that is the main aggressive medium that destroys steel structures, including pipes.

Besides, excess moisture sooner or later it will cause the appearance of fungus and mold not only on pipes, but also at any point in the apartment where there are cold surfaces.

And this is not just ugly, but often even dangerous for people living in the house, especially allergy sufferers.

What to do in case of misted pipes

The algorithm is very simple - you need to find the cause and eliminate it:

• You can start by checking the drain system of the tank and stopcocks. To do this, you have to watch them. Sometimes people, leaving the bathroom, do not notice that the faucet is dripping, and the toilet valve periodically opens due to a decrease in the float level due to a small leak from the tank.
• Check the operation of the ventilation with a piece of paper or by holding a lit match to the ventilation grille. If the piece of paper falls and the match burns evenly, then the ventilation is not working.
• If you did not find any malfunctions in your apartment, then you will have to visit the neighbors from above and find out from them if they have encountered the same problem. A fault on any floor above results in a constant circulation of cold water in the pipe, which significantly reduces its temperature.

• If in the bathroom and toilet you have forced ventilation, then it is worth checking the effectiveness of its work.
• If everything is in order, but the pipes are “crying”, then the reason for this is that the temperature difference between the surface of the pipe and the surrounding air exceeds 17 degrees, and special methods will have to be used to solve the problem.

Solutions to the problem

The main idea of ​​all the methods listed below is the thermal insulation of the cold water pipeline to reduce the intensity of exposure to too warm air.

• Painting pipes with heat-insulating paint. It is quite expensive, but effective method solution to the problem at hand. Here you should be patient, because to achieve the desired effect, you will have to paint the pipe at least 5-6 times. Each previous layer of paint must be well dried and only then apply the next one. In this case, the room will have to be forcibly ventilated - an ordinary fan is suitable for this.

• Pipe insulation with foam insulation pads. Linings are soft pipes with a longitudinal section. They are put on a dry pipe like a cover, and the edges are then glued. To achieve the desired effect, it is very important that the size of the lining ideally matches the diameter of the pipe. if it turns out to be more, then there will be no effect at all, and if it is less, then you will not be able to glue the edges of the lining. You can combine the two previous methods: first paint the pipe, dry the paint and put on linings on it, which can also be painted on top with heat-insulating paint.
• Putting a larger plastic pipe on the pipe and filling the space mounting foam, you can also achieve good results. But here it is important that the foam completely and evenly fills the space between the pipes, otherwise the method will not work.
• Self-creation of thermal insulation on the surface of the pipe. This is an inexpensive, but troublesome way, which is a completely reliable solution to the problem.

To create it, you need to stock up on the following materials:

• epoxy putty;
• simple cotton fabric (for example, old sheets);
• strong thread or thin twine;
• putty knife;
• sandpaper;
• means for cleaning pipes from rust;
• acetone or other suitable substance for degreasing the pipe surface.

The fabric must be cut into strips about 10 cm wide and wound into rolls. You can also use medical bandages of a suitable width.

Next, we proceed as follows:

• We clean the pipe from paint and carefully degrease its surface.
• Next, the pipe is treated with an anti-rust agent.
• After drying the pipe, a layer of epoxy putty must be applied to it and immediately quickly wrapped with a cloth from the bottom up. In this case, the turns of the fabric should be superimposed on each other and impregnated with putty. The fabric is then secured with thread.
• After the first layer has dried, several more are applied in the same way.
• At the end of the work, I again coat the pipe with putty on top.

After the insulation is completely dry, it can be sanded and painted with paint of a suitable color.

In solving the problem of "weeping" pipes, the main thing is not to miss the moment until the pipes begin to corrode.

If it is not possible to eliminate the problem by eliminating leaks in the valves of plumbing fixtures and good ventilation, it is better to immediately resort to thermal insulation.

Droplets of condensate on cold water pipes are a common occurrence, especially in summer when the air heats up to high temperatures. Droplets collect in streams and often puddles form on the floor next to the water supply pipe.

How to get rid of condensate, prevent corrosion of the pipeline, eliminate the fungus that occurs from moisture?

Causes of condensation on pipes

During the renovation of the premises, especially with constant high humidity It is worth taking care of communications in advance. Condensation on pipes, both metal and plastic, can occur for the following reasons:

1. Leakage plumbing as a result of improper installation, or in the process of wear.
2. Weak ventilation, improperly organized humid air exhaust system. blockages ventilation system lead to excess moisture on the surfaces of the room.
3. Leak in plumbing system, cistern toilet bowl neighbors.
4. A sharp temperature drop in the room where condensate collects. The situation is especially deplorable in the summer, when the surface of the pipeline is literally.
5. Configurations of distributing cold, hot water supply. If they are not thermally insulated, while located close to each other, condensation is inevitable (which is why it is so important).

How to get rid of condensation?

If moisture accumulates on the riser, it is possible that the neighbors have a mixer, other plumbing. This can be tested at night, when the characteristic sounds of flowing water are heard in silence. The problem with ventilation is observed when the windows are locked, especially those equipped with metal-plastic bags. Checking the operation of the system is easy.

It is enough to take a sheet of paper, attach it to the hood, clogging the windows, then do the same with the doors open. If there is no ventilation, the visual effect is obvious.

If moisture is concentrated on the apartment's wiring pipes, the reasons may be as follows. Faulty plumbing fixtures directly in the apartment may be to blame. The second reason is poor air circulation, especially in rooms with constant high humidity.

If the cold water pipe leading to the plumbing gets wet, the faucet, the shower faucet, the inlet valve of the tank in the toilet are to blame. When the riser is constantly getting wet, you need to look for the problem of water pipes from the neighbors from above. If the ventilation is clogged, it is worth checking the air circulation in it.

How to eliminate condensate?

You can get rid of the problem in several ways:

1. Check the hood, remove debris, cobwebs from there, then buy a compact fan, install it instead ventilation grill. Manufacturers offer wide range of similar devices, different in price, power.
2. Isolate the water supply system with special insulating tubes with a cut, which are available in building supermarkets. They are made of energy flex, polyethylene foam, the ends are fixed with permanent metallized tape. This method is the easiest, fastest, but before insulating the pipeline must be thoroughly dried.
3. Complete isolation will provide the following method. First, the pipe is sanded, after which the surface is wiped with acetone, then with a rust converter. After drying the pipeline, it is covered with epoxy putty and quickly wrapped with strips of fabric in 2-3 layers, the edges of the fabric are fixed with a clamp, wire. Then the epoxy putty is applied again, after drying, the surface is sanded, covered with paint.

Methods for protecting metal pipelines

If on metal pipes ah cold water supply does not eliminate condensate, over time they will be covered with corrosion. What can be done in this case:

1. First, the surface of the pipes is cleaned of rust, then dried, covered with drying oil, oil paint.
2. You can use carbolate, a paste-like mass for sealing cracks in floors and walls. The composition is applied to the surface with a 5 mm layer, left to harden for 24 hours. After that, it is sanded with fine-grained sandpaper, painted with oil paint.
3. Protective primers can be used, consisting of zinc dust diluted with drying oil, epoxy varnishes. They cover the surface of the pipe, after which they are painted with paints and enamels.
4. The pipeline in the toilet can be coated with a composition based on drying oil, minium in a ratio of 20:80 or primers such as GF-031, FL-03K, FL-053, GF-021.

If we are talking about the bathroom, here for painting hot pipelines, heated towel rails, oil-resistant enamels are used, for cold ones - any enamels, paints.

How else can you deal with condensation?

The following is a good way to fix the problem. It is necessary to put on the pipeline a corrugation with a diameter larger than that of the pipe, then fill the cavity between the surfaces with mounting foam. If puddles form on the floor, in the place where condensate accumulates, a sleeve made of pipes several diameters larger than the wiring itself will help get rid of them. The system is simple, while it will not interfere with the repair, replacement of the pipeline in the future.

Moisture absorbers sold in supermarkets household appliances is a great way to deal with a problem. They are a plastic box inside which an absorbent tablet is placed. The absorber will relieve not only of condensate on the pipe, but also eliminate humidity in the entire room.

A more expensive option is to install an air conditioner with climate control, which will ensure the optimal level of humidity.

It is advisable to waterproof the floor of the bathroom, toilet, which will help to cope with the problem of condensation on pipes and surfaces. If this method of repair is not feasible, it is worth opening windows after taking a hot shower, taking a bath, opening the bathroom doors. The circulation of cool air will quickly eliminate the accumulated condensate, help to effectively cope with moisture on the pipes.

Based on the practical experience of dealing with condensate on pipes, the masters advise the following:

1. Yuri Rogov, a plumber, recommends buying Gofroterm, a special compound sold in specialized stores. It is applied to the surface of the pipe, after which a strong elastic film is formed on it, which prevents the formation of moisture.
2. Andrey Kazantsev, foreman of the production site, advises to purchase liquid thermal insulation, which, like paint, is applied to the dried, cleaned surface of the pipeline. According to him, this method is better than thermoflex, other insulating materials.
3. If the ventilation, plumbing, plumbing is in good order, the cause of the accumulation of condensate may be the temperature difference between the pipe and the air. Locksmith Nikolai Korotkov advises in this case to conduct insulation. To do this, you will need long covers of polyethylene foam, or merylon, hollow inside, which are sold in construction stores. They are put on the pipeline, fixed at the bottom with a wire, a clamp.

You can get rid of fogging of the cold water supply pipeline different ways. Which one to choose should be determined after analyzing the situation.

Plumbing work, if you have a tool, experience, you can do it yourself, as an option - seek help from specialists. Read also the material about and you will be interested in the material about.

Small droplets of condensate form on cold water and sewer pipes in apartments and private houses all the time. Most often, this process can be observed in summer period. Despite the fact that such a phenomenon is considered natural and quite natural, it causes many inconveniences to many. We are trying to come up with something, but still, having seen the condensate on the cold water pipes, we don’t know what to do. Why are these droplets so harmful?

It would seem that harmless condensate can create significant problems for the owners of an apartment or house:

• Accumulating and uniting, drops of water end up on the floor and form whole puddles there, which can even flow to the neighbors below. The flooring from this can suffer so much that after a couple of years it will have to be replaced.
• Harmless drops also greatly reduce the operational period of the water supply, because this is an aggressive environment for metal. Pipes rust, deform and after a while will require overhaul.
• Condensation on pipes in a toilet, kitchen or bathroom can cause an unpleasant smell of dampness. But the smell is not so bad. Much worse, that the consequence of this is the formation of fungus and mold. Bacteria also multiply much more actively in a humid environment, exposing people living in an apartment to the risk of disease.

Reasons for the formation of drops

Why does condensation form on pipes? Most often this is due to the temperature difference between the surface of the pipes and the air in the room. And if there is still no ventilation in the room, or it does not function well enough, then nasty drops appear without fail. Contributes to this and too wet air in room. Moisture quickly settles on risers and pipes that conduct cold liquid. Every room has its own causes of condensation.

Wet pipes in the toilet

In the toilet, the most common causes of condensation on pipes include:

Condensation in the bathroom

To know how to deal with condensate on pipes in the bathroom, you must first find out the cause of this phenomenon. Some factors are similar to the "toilet", but there are some nuances:

How to get rid of moisture on pipes?

There are several ways to remove condensate from pipes:

Ventilation

Inspect the vent hole. If debris, cobwebs and dust deposits are found there, it is necessary to thoroughly clean it all. After that, it is advisable to purchase special fan, which is installed instead of the ventilation grill. In plumbing and building materials stores there are a lot of such devices from various manufacturers. They can be different in power, price and design.

New tank

In the toilet, the problem of condensate can be solved with a double tank. Inside such a device there is an additional plastic container into which cold water is collected. The outer walls do not cool too quickly, and therefore are not covered with water drops. Of the minuses is the high cost of the tank, which is most often sold only as a set along with the toilet.

natural ventilation

If your bathroom or bathroom does not have supply and exhaust ventilation, organize life in your home so that everyone who takes a shower or bath leaves the door wide open when leaving the bathroom.

Pipe insulation

How to get rid of condensate on cold water pipes by thickening the walls? To reduce the temperature difference between the air and the pipe, it is desirable to insulate the pipe. There are several items available in stores. modern heaters. They are characterized by high fire safety, high thermal insulation properties, ease of installation, tightness and a completely low price. Special cases made of foamed polyethylene - energy flex - are very popular now. This material is very flexible, so installation should not be a problem. And multiple closed pores will protect very well from temperature "inconsistencies".

To put the pipe in energy flex, you need to do the following:

• dry the pipe thoroughly, after wiping it with a dry cloth;
• the energy flex pipe must be cut lengthwise;
• starting from one end, gradually put the insulating material on the entire pipe with cold water;
• the longitudinal seam of the energy flex is fastened with clamps or glued with glue;
• if the pipe is long, then, using several pieces of insulation, you need to glue its ends together;
• after that, the insulating material, if desired, can be painted with paint from an aerosol can.

Another pipe and mounting foam

How to eliminate condensate on a cold water pipe using improvised materials? If for some reason you cannot buy this modern insulating material, then you can try using a plastic pipe with a slightly larger diameter and mounting foam. The plastic pipe is also cut lengthwise and carefully put on the water pipe. The foam is then injected into the annulus. This simple design will last long enough, and will not interfere with the conduction repair work.

Note: Instead of a plastic pipe, many use a metal corrugated pipe. Inside, you can also run mounting foam.

rags

Another option is to use rags (bandages, any other cotton fabric) and epoxy putty. Before proceeding with the insulation of the pipe, it must be thoroughly cleaned of rust with sandpaper, and then degreased with acetone and treated with a rust converter. Only after that the first layer of putty is applied, which is immediately “bandaged” with a cloth. When this coating hardens, you need to apply another layer of epoxy.

Isollat ​​and other similar materials

On the issue of thermal insulation of cold water pipes, a universal one helps a lot. insulating material"Isollat". This is a thermos paint in the form of a water-based suspension. After drying, the liquid mass solidifies and turns into polymer coating with excellent thermal insulation properties.

It is very simple to paint the pipe with Isollat:

• clean well with “sandpaper” and degrease the surface of the pipe;
• apply one layer of insulating substance;
• wait for drying;
• use silicone varnish finish coat and giving a glossy shine to the pipe.

Moisture absorbers

In large construction supermarkets, you can find wonderful household devices - moisture absorbers. They will help you quickly and without hassle to deal with the problem. Their design is quite simple: an absorbent substance is placed in a plastic box. It will help not only to eliminate condensate on the pipes, but also to get rid of excessive humidity throughout the room.

Air conditioner

This is the most expensive option, but some people use it too. Installing an air conditioner with climate control will ensure that the humidity level is always optimal.

What to do when the water condensate on the pipes keeps constantly? When you see water droplets on waterways your apartment, do not ignore the problem in the hope that "it will somehow disappear by itself." Try to apply one of the above methods, and unpleasant consequences can be avoided.

Condensation appearing on the pipeline is a frequent phenomenon. This does not make the bathroom more attractive, but rather, it becomes a problem. Wet pipes fail much faster, humidity also rises and mold begins to form. The issue needs to be resolved as quickly as possible. What to do if the cold water pipes start to fog up and condensation begins to form? First of all - do not panic, any problems in the operation of your bathroom must be eliminated. You just need to familiarize yourself with the ways to deal with unwanted moisture and get down to business.

Causes of condensation

Residents of apartment buildings often encounter such a phenomenon as a “sweating pipe” with cold water. The causes of occurrence may be different. The nature of the appearance of water droplets on the pipes in the bathroom and in the toilet is slightly different. In a combined bathroom, the main reasons are:

Often the cause of condensation in the bathroom is poor ventilation.

• insufficient;
• continuous dialing ;
• malfunction of work (passes the valve that shuts off cold water);
• a large difference in the temperature of water and ambient air in the room;
• high humidity or leakage from neighbors from above.

The bathroom should be well ventilated, air circulation allows you to remove unwanted moisture. With the continuous operation of the filling system of the tank, moisture condenses not only on the riser, but also on the wiring. A faucet dripping all the time causes a similar problem.

Faucet failure can also cause high humidity in the bathroom.

Each of the reasons can independently cause “fogging” of the riser or cold water distribution pipes, but, as a rule, the cause is precisely the combination of several points.

Advice! If the humidification of the pipes began suddenly, remember what changes you made in your apartment in Lately. The reason may be the change of windows, and the installation of any other equipment that increases the temperature of the room.

What threatens the "sweating" pipe

The condensate that appears on the pipes is not just water droplets. First of all, it is an aggressive environment for. In conditions of high humidity, the material corrodes and quickly fails.

In conditions of continuous humidification, the smell of dampness appears in the room. In addition, in places of high humidity, excellent conditions are created for the development various bacteria, including mold and all kinds of fungi. Constant human contact with this kind of "neighbors" is highly undesirable and can cause malfunctions in the body.

For metal pipes, constant moisture is fraught with rust.

If the appearance of condensate or its abundance is not detected in time, puddles may form on the floor. If they are not eliminated in time, then it is possible to bring the time for repair work to be replaced floor covering in the bathroom.

What to do if you detect fogging on the pipes

If you notice in the bathroom that the riser or other pipes related to the cold water supply are covered with small drops of water, then a series of actions should be taken to find out the cause. Our algorithm will help you:

Important! If all the malfunctions in the water supply system have been eliminated, the ventilation is working correctly, then the appearance of moisture is due to the temperature difference.

Installing new windows or additional systems heating necessarily affects the temperature in the room. If the difference between the temperature of the water in the pipe and the air in the room is more than 17 ° C, then condensation will certainly appear.

We get rid of the problem with the help of special devices

If the temperature difference was established as the cause of the “sweating” pipes, then the first necessity will be the insulation of the cold water riser. A variety of materials can serve as a heater, they all differ from each other in price, appearance and degree of insulation.

The simplest option is purchase of foam pads thermal insulation material . They look like soft pipes with a cut along. The insulation is put on the pipe like a cover and glued together. It is very important not to make a mistake with the size. If you purchase an overlay with a larger diameter, then there will be no effect, just like with a smaller size (you cannot glue this one).

Insulation lining for cold water pipes

A more expensive but very effective way is to apply thermal insulation paint. To insulate the cold water riser, it is necessary to apply 4-6 layers of the substance, allowing each layer to dry completely. When working with paint, it is important to ensure forced ventilation premises. To do this, you can use a conventional fan.

Heat insulating paint

For greater effect, you can combine the two previous methods. Make sure that the coating is completely dry before putting on the painted pipe insulation. It is also allowed to apply a layer of paint on top of the heat-insulating nozzle, but only after it is well fixed.

Another means for warming is a larger plastic pipe, put on the main one. The formed air space is filled with polyurethane foam.

Important! When carrying out any work on the insulation of the pipe, it is necessary to completely dry it in advance from the formed drops.

Each of these methods is very effective, but if you did not count on your funds to purchase expensive coatings, you are better off using the old proven method - to create thermal insulation yourself.

Creating thermal insulation with your own hands

It is not so difficult to make a heater for a cold water riser yourself. For this we need:

• sandpaper;
• rust converter (eg phosphoric acid);

Rust Remover

• strong thread;
• cotton fabric (you can use old things);
• epoxy putty;
• putty knife.

An old sheet or duvet cover is well suited as a heater. Various bandages and other materials can be used. Large and wide canvases are best cut into strips up to 10 cm wide and rolled into rolls.

Epoxy putty

Next, you need to clean the pipe itself and degrease the surface. Deal with it common remedy acetone based nail polish remover. The next step is to treat the riser with a rust converter.

After careful preparation, you can begin warming. Apply a layer of putty and, without waiting for it to dry, wrap the pipe tightly with a cloth from the bottom up. Wind the fabric so that each turn overlaps the previous one and is saturated with putty. At the end, secure the bandage tightly with a thread.

Noticing that condensation often appears on the pipes in the bathroom, do not delay solving this problem.

After drying, apply a few more layers of insulation. The final step will be coating the pipe with putty. When the homemade casing is completely dry and hardened, it can be sanded and painted to match the wall.

Do not leave the problem with high humidity unattended. This depends not only appearance your bathroom, but also the integrity of the cold water pipes.

How to get rid of condensation in the bathroom: video

Condensate on pipes: photo

The formation of condensate (water droplets) on the surface of pipes is a frequent and common phenomenon. Condensation is present in apartments with centralized water supply, country houses and cottages equipped with individual pumping station. It is observed in summer season and in winter. The smallest droplets of water form on the surface of sewer and water pipes, and sometimes on the surface of walls. This process in itself cannot be considered a big problem. But the accumulation of water leads to a reduction in the life of the water supply system and to the flooding of neighbors due to leaks. Excessive moisture causes dampness in the toilet, bathroom, kitchen and bad smell leads to the formation of fungus and mold.

The appearance of condensation on the pipes in the toilet

Condensation on cold water pipes is formed due to temperature differences. Another reason lies in bad job ventilation system or none at all.

Strong condensation on the pipes in the toilet appears for the following reasons:

1. Inefficient room ventilation. You can check if this reason is correct. in the following way. Do not close the toilet door at night. If the pipes remain dry in the morning, this will confirm the weak operation of the air ventilation system.
2. Regular flow of the drain tank. In this situation, the water constantly flows, not having time to warm up, so it remains cold. The room air temperature is much higher, due to the temperature difference, condensation appears. To remove condensate from the toilet bowl, repair or replace the outlet valve or faucet on it.
3. Faults and leakage from neighbors. Water flows through the riser, so as a consequence wet pipes in the toilet. You cannot solve this problem on your own. Join forces with your neighbors, or better yet, invite a plumber. But if it is impossible to connect them immediately after finding the cause, then it is possible to temporarily eliminate the condensate on the pipes in the toilet as follows. To do this, wrap four or five turns of a bandage or strip of fabric on the pipe, and lower the remaining canvas into a container. The accumulated liquid should be poured out periodically.

• Poor ventilation or exhaust, or lack of it. In this case, the cold water pipe is sweating. Sometimes you just need to clean the ventilation. Unscrew the grate that is used as a valve to shut off the air circulation, thoroughly clean all structural elements ventilation.
• Features of laying the water supply and sewerage lines. IN apartment buildings pipes for cold and hot water laid side by side and without any thermal insulation. This circumstance explains the appearance of condensate on the pipes that lead to the mixer. If they are laid inside the wall, then serious repairs are indispensable. In the case of open pipe laying, a thermostat is used.
• Boiler valve dripping. This problem can be eliminated by winding a special tape.
• Damage (leakage) of the mixer. Constantly flowing liquid leads to the fact that cold water pipes sweat, the humidity in the apartment rises. You can get rid of condensate by replacing or repairing the mixer.
• Stand leak. Get rid of condensate on pipes with such
  problem, you can either temporarily (wind up a bandage or cloth, and lower the free end into a container to collect fluid), or replace the riser or only the damaged part.

To avoid the formation of moisture, it is better to start by checking and adjusting the operation of the ventilation and exhaust system. Humidity should not be higher than 50% in the house. Humidity standards in the apartment are set by the relevant sanitary standards and rules. The optimal humidity is 45 - 30%. If the ventilation is working properly and works well, then the humidity of the air remains within the normal range.

The next option is to eliminate possible leaks in faucets and the toilet flush tank. If they cannot be repaired, simply replace them.

When these measures did not help to eliminate condensate and bring air humidity back to normal, then use other methods. A new innovative method - waterproofing paint. It should only be used on absolutely dry and rust-free surfaces. If laziness, then of course it is not forbidden to paint the pipe with condensate, but this is a waste of work. Therefore, before work, be sure to turn off the water.

When cleaning surfaces, it is better to use fine sandpaper and do not be zealous (especially if the pipes are plastic), as this can damage them.

Another option is insulating pipes with a special cut. Before use, they must be wiped to prevent moisture droplets from getting inside the insulating layer.

Means of thermal insulation "Grafoterm" when applied forms protective film, minimizes the possibility of condensation on plastic cold water pipes.

Condensate on water pipes eliminated in a simple and economical way, however, while they themselves will not look very aesthetically pleasing. Wrap them with a bandage or strips of cloth. Alternate layers of bandage with epoxy putty, in this case the waterproofing is much more reliable.

1. Purchase of ready-made thermal insulation material. Market building materials has them in a wide range. These are energy flex, foam propylene, penofol, self-adhesive tape and others.
2. Plumbers recommend using high-diameter plastic pipes. Soft, but strong, with thick porous walls, such a pipe is easy to install.

They are produced in several standard sizes, inner diameter corresponds to the outer diameter of the water pipe.

1. The thermal insulation pipe is cut lengthwise, put on a water pipe, and the seam is sealed with special adhesive tape (metallized). If the pipes in the toilet are sweating, then for lack of funds, you can get by with a simple corrugated pipe or thick cardboard. Cut off pieces of the required length, with a diameter slightly larger than the tap. Then put on the problem area and fill with mounting foam. Pieces short in length are glued together with tape.
2. The easiest and most economical way to insulate, if the cold water pipe is sweating, is to apply epoxy putty. Before application, the surfaces must be very thoroughly cleaned from corrosion and rust, and then degreased with an acetone-containing solution. When the putty solution hardens, the pipe is bandaged, and then another layer of the solution is applied, after it dries, the last, final layer.,

Getting rid of condensate on pipes

The fight against condensate must be rational. If it was not possible to completely get rid of moisture droplets or prevent their appearance by any of the methods, you need to pay attention to other reasons:

• Weather conditions - a humid climate and frequent prolonged rains, prolonged severe frosts or heavy snowfalls increase the level of humidity in the room, and as a result, condensation appears.
• The location of the house near natural reservoirs, close occurrence ground water affect the level of humidity in the house.
• Disadvantages of construction - the foundation waterproofing layer has not been laid, there is no ventilation, cold floor or damp basement located under the house.
• Frequent accidents in the water supply system, the presence of several sources of evaporation (drying clothes, cooking) are also causes of condensation.

Most often, to solve this problem, it is necessary to completely change the internal microclimate of the house, and this requires complex complex measures, up to and including a major overhaul. Each of the situations of condensate occurrence requires a study of the causes and an individual choice of method and method of elimination.

Sometimes activities can be simple and economical.

• In case of excessive moisture, eliminate the source. Use only well-ventilated areas to dry laundry.
• Equip exhaust ventilation, so that it works in several modes, including forced.
• Additionally insulate the walls and floor.
• Install an air conditioner with a dehumidifier function. If this is not possible, then make a moisture absorber with your own hands.