Do-it-yourself swing made of metal: very often, when arranging the courtyard of a private house or garden, they are installed swing... Such structures are made of metal, wood, car tires and other materials at hand. But in order to achieve a really high-quality result, use drawings and photos of garden swing with their own hands made of metal: The dimensions and performance of these products allow them to be used for a long time.
Features swing structures made of metal are strength, reliability and durability
Do-it-yourself garden swing classification made of metal: photos and features
Various materials are used for the construction of metal structures. Therefore, there are so many design solutions. This is evidenced by numerous photo of a garden swing with your own hands made of metal which can be found on the internet.
Futuristic swing design made of metal
For the manufacture of structures, the following material options are used:
- metal corners;
- square profiles;
- I-beams (steel beams);
- pipes (round profile);
- brands (aluminum profiles).
Hanging swing made of thin pipes located on the terrace of a country house
Note! On the basis of these elements, both family-type benches and small-sized baby rocking chairs can be created with equal success.
Before you start planning and developing garden swing drawings do it yourself made of metal, you need to decide on the type of future design. To do this, you can study the ready-made systems offered by modern industry.
Original swing suspended type with metal frame
Like metal: photos and examples of products
If you puzzle over how make a swing with your own hands for children, take factory production options as an example. Such products have a correctly calculated design and are represented by a large number of interesting design solutions. You just need to create a similar swing from scrap materials.
Suspended from a metal frame on chains
Product classification from manufacturers:
- freestanding garden constructions. This type of product can be installed anywhere you deem suitable, since it does not require additional support or hangers. A swing of this type can be not only metal, but also wooden;
Material for garden swing both metal and wood can serve
- sofa swing that can be used by both adults and children. In the second case, the product allows several skiers to sit on the bench at the same time. The constructions are comfortable and safe, equipped with a comfortable backrest. During heavy rains or in winter swing easy to clean, as their design has a block structure. Products can be metal or wood;
Mobile version of the swing metal with ethnic style seat
- structures equipped with a folding back and a mosquito net. They can be used as children's metal swing for giving... You can add other accessories for added comfort;
- swing made by forging, which have many advantages.
Factory metal garden swing installed in the garden of a private house
Photo of a garden swing with your own hands, created by forging
Swing of this type are carried out mainly for installation in the territories of country houses. To create these products, you will need skills in handling a welding machine and metal, or you can hire an assistant. In this case swing are more durable and powerful than other options for metal structures. In addition, you get an original product that can become an interesting decorative addition to the landscape and exterior of the house.
Mounting dimensions diagram forged garden swing(1 inch = 2.54 cm)
Metal products made by forging are expensive. But it is justified by its excellent decorative characteristics.
Helpful advice! Use similar designs to maintain the overall design of your home and surrounding area with fences, window bars, street lamps, benches, balconies, stair railings, canopies (), or gazebos that are constructed using this technology. To achieve unity in design, use the same or similar pattern on all the listed items by forging.
Weightless in appearance and graceful forged swing with colorful pillows
Characteristics of a garden swing with your own hands made of metal
Metal structures have the largest number of advantages over products based on other materials. That is why there are such a large number of photos and drawings of children's swing with their own hands made of metal.
Technical and operational swing characteristics metal-based:
- long service life is one of the main benefits. Metal is not susceptible to the destructive effects of such factors as, for example, decay processes. Breakage due to drying out is also excluded;
Wicker swing-cocoon with a metal frame will become an unusual decoration of the courtyard of a private house
- practicality - environmental influences destructive to buildings (ultraviolet radiation, rain and other types of precipitation) cannot affect the strength characteristics of the material;
- reliability - due to the increased strength of the metal and its durability, the resulting structures are very strong;
Metal pipes are an excellent material for creating a frame for a children's swing
- budget - the metal in the purchase has a lower cost than high quality wood (low quality wood will not be able to ensure the strength of the product, therefore, for creating a swing it does not apply);
- variety of modifications - assortment modern swing, which you can purchase or do yourself, is extremely wide, which allows you to choose a design that fully meets individual preferences.
Fancy hanging swing made of thin metal pipes
Cons of homemade swing for a summer cottage made of metal
Despite the external attractiveness of metal products, by themselves they will not be able to harmoniously fit into the suburban area, as is the case with swing made of wood... This will require stylistically supporting their design by adding similar elements to the exterior of the house or garden.
Note! Metal structures can do it yourself however, you need to learn welding technology and skills, as well as purchase or rent the necessary equipment.
Cozy metal swing with wicker plastic seat
One of the positive characteristics of the material, namely the hardness of the metal and its strong structure, can also be considered a disadvantage. On the one hand, durable and solid swing- what is needed for a summer residence, on the other hand, they can cause serious injuries that a person can receive as a result of a blow. Compared to wood, which is soft in nature, metal is many times more dangerous.
Metal products are subject to corrosion. Rust can lead to gradual deterioration, so the durability of a structure can only be ensured with proper care. To prevent the appearance of corrosion, it is sufficient to cover the metal with a layer of a paint composition intended for metal surfaces and outdoor conditions in a timely manner.
Hanging children's swing with a frame made of metal
Drawings and photos of a garden swing with your own hands made of metal: dimensions and technology
Manufactured do it yourself garden swing can have a different type of frame. Based on this feature, the following design options are distinguished:
- collapsible;
- welded.
Welded swing types require the use of a welding machine and other special equipment. As a result, you will have a strong and rigid support part, which will allow you to operate the structure for many years without any risk to health.
Frame mounting dimensions garden swing from shaped pipes
If you do not know how to handle a welding machine, choose a swing with a collapsible design. The principle of assembling the frame consists in twisting all elements of the product with bolts and nuts. Anyone can do this kind of work.
Note! Over time, in hand-made metal garden swings, the threads at the joints under weight and other loads gradually loosen up. As a result, backlash (free space) appears. It can provoke the destruction of the structure, as a result of which it is possible for a person to get injured. To prevent this, secure the elements with grovers and locknuts. Do not forget to regularly tighten the joints with a key.
Modern design metal swing for garden
A brief classification of a garden swing with your own hands made of metal
The easiest way is to create a structure according to ready-made do-it-yourself garden swing drawings made of metal... Considering the schemes, you can see that the configuration of the supports is different.
The A-shaped frame base consists of two crossbars, which are interconnected at the top. There is a jumper approximately in the middle of their height. It is designed to increase the rigidity of the structure. There are supports without a lintel, which are L-shaped.
Bright baby swing metal with A-shaped support legs
Another type of support is elements with a crossbar that form a U-shaped base. The creation of such a structure takes less effort, but the swing is less stable. Their operation will be long-term and safe if the base supports are placed in deep holes in the ground and well concreted.
In addition, all metal products can be divided into two groups:
- stationary - support part swing securely concreted;
- portable - fixed with anchor bolts or bent reinforcement, which is hammered into the soil.
Metal swing located in the garden of a private house will become a favorite place to relax
Do-it-yourself swing technology from a profile pipe
Hanging swing are considered the most common design options. They are comfortable, practical and comfortable. Equip the product with a canopy to protect it from direct sunlight. Thanks to this, the seat will not overheat, and the riding process will become even more comfortable.
For the manufacture of a canopy for DIY metal swing for children textiles, tarpaulin, wood with soft tiles in the form of a roof can be used. But the most suitable material is cellular polycarbonate. The polycarbonate sheets are transparent so it won't be dark under the canopy. At the same time, they perfectly scatter direct sunlight.
Frame drawing for a garden swing from a profile pipe
List of required tools and materials
Before making garden ones, make sure you have the appropriate tools:
- grinders;
- building level and tape measure;
- welding machine and protective equipment (for working with the machine);
- electric drill;
- a set of drills designed to work with metal and wood surfaces;
Mobile hanging swing- armchair with metal frame
- screwdriver;
- a set of wrenches;
- self-tapping screws designed to fix polycarbonate sheet.
For work, you will also need to purchase materials, namely:
- metal profile (pipes and corner);
- boards or blocks of wood for assembling the seat;
Metal swing of the original form suspended from a tree branch with a rope
- bolts equipped with semi-countersunk heads (for seat assembly);
- washers and nuts for bolts (for seat assembly);
- fasteners made of stainless steel or galvanized (carabiners, bearing hangers, eyebolts, chains);
- long anchors or bent reinforcing bars (for fixing the structure to the base);
Device diagram and mounting dimensions of the swing frame made of metal
- a sheet of cellular polycarbonate (canopy roof);
- protective agents for the frame (primer with anti-corrosion properties and paint composition for metal surfaces);
- protective agents for the wood from which the seat will be created (stain, varnish, a set of brushes for surface treatment).
The choice of designs for creating a swing from metal with your own hands vast and limited only by your imagination
Drawings and photos of a swing with your own hands made of metal: the preparatory stage
At this stage, a zone is selected for installation of a swing, the dimensions of the structure are determined. The optimum size of the hanging bench is 1.5 m. This is enough for swing it was possible to accommodate two skiers or lie down one.
Helpful advice! Be sure to create a gap between the rack structure and the side of the bench. The minimum size is 300 mm.
Dimensions for the manufacture of metal children's swing
According to garden swing drawings with your own hands from a profile, the structure consists of the following elements:
- support frame of rectangular shape at the base;
- sidewalls made of a pair of pipes, welded together;
- horizontal bar for hanging the bench.
Process creating a garden swing design consisting of metal pipes
This information will help with further assembly. Thanks to this structure, the structure acquires the required level of rigidity. By choosing the right base width, you can build a very stable product. Take the rule as a basis for your work: the greater the angle that is at the apex of the triangle between the base and the sidewalls, the more stable the structure will be.
Diagram of the structure of the swing made of metal with A-shaped posts: 1 - flange; 2 - nut; 3 - crossbar; 4 - eye nut; 5 - support frame support; 6 - frame brace; 7 - bolt
General dimensional parameters are calculated on an individual basis. The indicators regarding the polycarbonate visor and the hanging bench are adjusted to them. Experts recommend that it is mandatory to prepare drawings indicating all the dimensional parameters of the structure, so that it is more convenient to work with the material. Subsequently, this will save you from mistakes and save time.
Sizes of different mobile swing chairs made of metal. Similar designs can be made with your own hands
Do-it-yourself assembly according to the drawings of a swing from a profile pipe: frame part
It is recommended to start assembling the frame from the side parts. To do this, on the basis of the drawings, you need to mark the pipes and cut them with a grinder. Check the dimensional accuracy before assembly. All four sidewall elements must be similar to each other. They need to be connected in pairs using the welding method. As a result, you should have two identical L-shaped parts.
Diagram of the frame device with dimensions for metal garden swing
Further, the sharp end, located at the top of each of the parts, is sawn off at the same level. This procedure is performed so that a small support area can be formed to secure the horizontal bar.
Helpful advice! Use a pre-prepared template for work.
Metal swing do it yourself unusual shape can become the main attraction of the personal plot
The width of the support frame (short side) should be sized to match the distance that is formed between the paired pipes of the side parts of the structure. The welding machine welded the sidewalls to the rectangular support frame, and then the horizontal crossbar (over the side posts).
All stages of the assembly of the frame part must strictly obey the laws of geometry: the side posts have a vertical type of arrangement, the horizontal crossbar (beam), intended for hanging the bench, runs parallel to the base. Use the building level to control assembly parameters.
Frame diagram children's swing from a profile pipe
Assembly technology of wooden swing seat
- an important stage of construction. Especially if you create software children's swing drawings made of metal with your own hands... At the base of the seat, there should be a frame base made of a steel corner. To get a bench with a comfortable back, position it at a specific angle in relation to the seat. The optimum angle is 120 °.
Garden swing family type with metal frame and wooden seat
To make a correct bend of the corner, make a triangle cut (60 °) on one shelf. The frame for the seat is made of a rectangular metal profile using a welding method. The side parts should be connected along the edge zones using horizontal jumpers. The connection zone should also be in the place where the structure bends.
Three different swing seating options with metal base to which wooden slats are attached
Helpful advice! If you wish, you can improve the structure by adding armrests to the seat. They will enhance comfort and safety.
Whether you are making a DIY swing design for children or making a product for adults, the back and seat should be completely smooth. For these purposes, suitable wooden blocks or boards, carefully processed with sandpaper (first coarse grain, then fine).
Unusual swing hanging type with metal frame
The boards are cut to the required size and attached to the frame through pre-drilled holes with bolts so that their heads are recessed. Before the final assembly of the structure, wooden elements are treated with an antiseptic and varnishing composition, and metal elements - with a primer and paint.
Eye bolts are mounted in the corners of the frame part of the bench. The chains will be attached to the lugs of these bolts with carabiners or threaded couplings. To hang the bench, you will also need to install eyebolts at the corners of the product or over the edges of the seat.
The procedure for making a garden swing with metal frame
Making a visor for a structure
The visor manufacturing process is optional. But if you create a do-it-yourself swing design for children, you should think about comfort and protection from the scorching sun, as well as precipitation.
To do this, you need to make a rectangular structure, which will be based on a metal frame, reinforced with jumpers. A sheet of cellular polycarbonate is fixed on top of the structure. Installation of the visor is carried out at a slight angle, due to which the precipitation will flow down freely.
Metal swing sofa type with a visor, installed in the courtyard of a private house
To complete the frame part of the visor, take several metal profiles with a small square section. All these elements are fastened by welding, after which the visor can be attached to the upper frame part of the swing. This is also done using a welding machine.
When all the assembly work is completed, the structure is subject to final processing. The surface of the swing is covered with a primer, after which it is painted in any color you like.
Various options for creating a canopy
polycarbonate over the swing
The final stage of construction
When the paint is completely dry, a sheet of polycarbonate is attached to the visor frame. To do this, use self-tapping screws with sealing washers.
Helpful advice! Cover the end part of the sheets with a polymer profile. It will protect the hollow polycarbonate structure from insects and dust, preserve its beauty and neatness.
A wide range of colors is one of the advantages of polycarbonate. You can choose the color of the visor to match the color of the swing, or, conversely, make it contrasting. Moreover, the color of the material has a direct impact on the level of dispersion of sunlight.
A wooden pergola acts as a basis for hanging a swing made of metal
The finished product must be securely fixed on the concrete site. If the structure is being erected on high-density soil, several clamps made of reinforcing bars can be used to secure the frame. First, the ends of the clamps should be sharpened, which will make it possible to drive the rods 0.5 m deep into the ground without any problems.
It is better to use anchor bolts as fasteners on a concrete site. They are pre-installed in the appropriate locations. After tightening the nuts, cut off the excess thread with a grinder. This completes the construction of the structure.
From metal, using the photos and drawings presented in the article. If you have children, then you cannot do without a swing. In addition, you can not only ride on it for children, but also spend holidays with the whole family, read books and just relax after a working day.
If you approach construction creatively, then as a result you will get an original structure, which will surely become a decoration of any courtyard. The versatility and ease of manufacture explain the high popularity of the swing. You can build it yourself, because the finished product often costs a lot of money.
Swing made of metal in the yard
Varieties and features of designs
Despite the simplicity of the design itself, there are many varieties of it. In addition, they can be made from a wide variety of materials. For example:
- wood;
- metal;
- car tires;
- cables that are attached to the tree, and so on.
But still, the metal structure is considered to be the most durable. Moreover, metal is the most durable material. To build such a swing, you need a square-shaped metal profile, metal corners and pipes. Brands (or I-beams) are also used.
If we talk about the frame, then there are the following:
- welded (stationary, elements are attached using a welding machine);
Welded swing frame
- collapsible (at any time you can disassemble the swing and move or fold).
Collapsible swing frame
The first option requires the builder to have special professional skills and experience with the welding machine. But at the same time, the welded support will be more rigid and durable. Therefore, you will be able to operate the swing for a long time and not be afraid that some fastener will fall off.
Everyone can collect the second option. Bolts and nuts are used for the connection. But such a swing will serve you less, due to the loosening of the threaded connections. For strengthening, you need to use lock nuts and grovers. Then you just have to tighten them from time to time in order to prevent backlash between the connecting elements.
Collapsible drawing
Separation by reference configurations.
- "A" -shaped frame: it includes crossbars (2 pcs.), Which are connected at the top. There is a jumper between them to give the frame rigidity. Alternatively, there are swings with the shape of the letter "L".
- "P" -shaped frame: support pipes with a crossbar are connected in such a way that the letter "P" is obtained. It is the simplest to construct. But at the same time, the most unstable. To prevent overturning and similar situations, it is necessary to bury the pipes to a great depth and fill with concrete.
If we talk about attractions, then there are also two types:
- stationary: their support frames are firmly concreted;
- portable: supports are fastened with anchor bolts, bent reinforcement, which is driven into the ground.
Consider several options for how to make metal, depending on age characteristics. The presented photos and drawings will help you better understand the essence and sequence of the process.
Video Garden swing
Metal swing for children (up to six years old)
Toddlers under six years of age are most active in swinging. Therefore, such structures are most often built for them. Since their weight is not very large, you can choose elementary options. The optimal material for this is a pipe with a diameter of 50 mm or more.
Before starting construction, be sure to create a drawing or take a ready-made one in order to avoid any mistakes. The diagram carries a lot of important information: size, construction features. On its basis, it is easy to calculate the amount of required materials, so that later you do not buy or rack your brains about where to put the leftovers.
It will be quite comfortable for children to ride on a swing "P" -shaped, the height of which is from 1.5 to 2 m. It will be most practical to make it portable. To ensure its stability, a metal square is welded at each lower end of the support.
Swing for preschool children
After that, a metal rod one meter long must be clamped in a vice and bent so that a hook is obtained. Half of the rod must be driven into the ground. Four of these rods are enough to securely fix the swing.
Making a swing for school children
Compared to the previous version, such a structure should be many times stronger. After all, the load will be greater, and the child's weight will increase. The support legs will have to be welded at a certain angle. After that, they are additionally fixed with a horizontal lintel, which is one third of the structure's height above the ground.
Next, you need to fix the crossbar between the two supports. For these purposes, you can prepare a workpiece in advance. You will need three pipe cuts. The ends of the crossbar and supports are then inserted into them. Follow these instructions:
- the triangle-shaped plate must be welded to the posts (above) and a hole of the required size must be made in it;
- take a bolt so that the diameter is slightly smaller than the diameter of the crossbar. Using a grinder, carefully cut off the head in it;
- the created pin must be inserted into the pipe and fixed with a bolted connection. This requires making holes through and through in these parts;
- into the created blank from the triangle, you need to thread the hairpin, which is already welded to the uprights. Tighten all this with a lock nut with a regular nut, giving strength to the connection;
- the support posts need to be concreted with high quality. To do this, you need to make holes (you can use a drill or dig it yourself). The depth of the pit should be between 40-50 cm;
- set up racks and fill in gravel with sand and tamp well to minimize voids and level the surface;
- pour everything with concrete solution. Then it should be left to dry completely, which occurs after about a week.
Ready-made swing made of metal "L" -shaped
How to fix the seat correctly
We note right away that you can purchase a seat for a swing ready-made or make a homemade one. Making at home will allow you to make the most suitable look for you. In any case, the mounting options will be the same.
Drill holes of the appropriate size in the crossbar. Then you need to thread anchor bolts into them, which have a special loop at the end. It is through these loops that the hangers for fixing the seat are threaded. Important: Be sure to tighten the nuts with the locknuts.
Fastening with anchor bolts
Use of bearings. This option is considered the most robust and reliable. But for a permanent effect, it is necessary to periodically lubricate them. Otherwise, there will be an unpleasant creak.
Bearing connection
Using clamps. Take clamps of a round or square profile (depending on the type used in the construction) with special hooks for hanging the seats.
Clamps for fixing the seats
The seat itself can be hung on any suspension you have. The material does not play a special role here. The most common suspensions are:
- synthetic rope;
- chain;
- metal cable (not less than 7 mm);
- automobile transportation rope;
- climbing equipment.
Before choosing, it is worth considering all the nuances of each of the materials presented. For example, metal chains are susceptible to corrosion processes and will rust in service. Painting them causes some difficulties. Therefore, it is better to initially buy galvanized chains.
Swing on chains
Building a Texas swing at home
The Texas swing is gaining more and more popularity, which can easily withstand several adults. They have a large seat with a backrest on which you can lie and sit. Often, such a swing has a canopy or canopy so that you can comfortably sit on it both in the heat and in the rain. Such a garden option can be done independently, taking into account all your wishes.
Swing Texas in the garden
Required materials and tools:
- steel pipes with a diameter of 7 cm;
- metal corners;
- reinforcing arcs (diameter 1.6 cm);
- furniture foam rubber (according to the dimensions of the seat);
- a canvas made of wood (you can take unnecessary, but durable doors);
- fabric for seat upholstery;
- cord or chain for suspension;
- fasteners;
- welding machine.
Before construction, a drawing is created with the main information. Then you can proceed to the construction itself.
Support
Clean pipes from rust and other damage, measure the required dimensions and create blanks. The easiest way to cut off the pieces is with a grinder. Where there will be a joint, it is necessary to remove the chamfer at an angle of 45 degrees.
Weld the pipes in accordance with the drawing. After the support is ready, weld the "ears" (arcs created from the rod) to it. The seat will be suspended from them. The entire structure should be painted.
Welded construction (corner)
The construction of the seat and its back
Weld two pieces of metal corner at an angle of 100 degrees (rectangles). One will serve as the back of the swing (located at the top), and the other as a seat (located at the bottom).
Holes must be made in the lower rectangle to attach the seat itself.
Use a piece of wood to make a seat insert. The back is also cut out of it.
Finished back and swing seat
Fastening
To hang the swing, you need to use very durable materials. It can be either a rope or a special fastener. In addition to a strong attachment, it is important to make sure that your harness does not "walk" on the hook. To avoid this, you can use special mounts.
Swing mounts
Installation
The swing turns out to be massive, therefore it is of a stationary type. It is worth worrying about a shed or a gazebo in order to protect the wooden elements of the building from adversity. This way they will last much longer.
A canopy gazebo over a Texas garden swing
Swing Texas will be able to provide you not only a pleasant vacation, but also a general pastime with family and friends. After all, the swing is created strong, so feel free to sit down together or even four.
Now you know in detail how to make a swing in the country with your own hands from metal, and photos and drawings will help you create a holistic picture of the upcoming work. Don't believe it's that easy? Then watch the video where you will learn about the smallest details of this issue. And warm summer evenings will certainly become memorable and fun. After all, it is difficult to resist and not sit on a beautiful swing.
Video: garden swing
In most cases, the arrangement of a summer cottage is related to the installation of a swing. Various materials are used to assemble such equipment, among which ordinary boards and car tires can be mentioned. This approach is common, but not rational, since there are special drawings that facilitate the installation of a swing structure made of metal. If you follow them clearly, you can assemble a device for a pleasant pastime, which is an ordinary swing.
Most of these structures are due to the presence of a frame and a variety of metal elements. Such devices are divided into two types:
- welded;
- collapsible.
The first option is the most problematic in terms of home installation. This is due to the fact that it requires special equipment in the form of a welding machine, as well as the ability to use it. Otherwise, the welded structure is the best solution, as it provides high strength and sufficient rigidity to guarantee a long service life of the installed swing device.
At the same time, the collapsible frame allows any home craftsman to assemble it without the proper skills and special equipment. Moreover, such a structure is not without its drawbacks. Whatever the threaded connection, it loosens over time, which leads to a loss of structural rigidity.
As a result, a backlash is created, as a result of which the swing does not just start to walk, but becomes a source of danger to human life and health, as it can collapse at any moment. Hence, it becomes necessary to use locknuts and Grover washers in order to ensure the required stability of the rocking device.
Depending on the configuration of the supports, the structure may have:
- a frame resembling the letter A, where two crossbars are installed in such a way that they close on top, and a transverse beam gives them rigidity, which makes the swing similar to the aforementioned graphic sign; there are also L-shaped structures without a lintel;
- a frame in which the beams are connected in the form of the letter P; this option is less stable against the background of low labor costs, since the installation of such a swing is simpler; to give the U-shaped devices sufficient strength, it is necessary to take care of high-quality concreting of the supports.
Such structures can also be subdivided into the following types:
- stationary, which cannot be moved due to the fact that their supports are concreted;
- portable, connected by means of anchor bolts.
Children under 6 years old
Kids are lightweight, which allows you to create a swing that is simple in terms of design. At the same time, do not forget about the proper level of security, which should be as high as possible. For a swing of this type, a pipe with a diameter of more than 50 mm is suitable. Before proceeding with the assembly, you should take care of drawing up a detailed drawing.
An L-shaped structure with a height of 1.5 to 2 m is quite appropriate in this case. It is optimal if the swing will be implemented as a portable version, which is achieved by welding a square base.
Next, a metal rod is used, which is bent so that it takes the shape of a hook. The length of such a workpiece should be about 1 m, taking into account the fact that about 50 cm of the rod will be underground. To ensure acceptable stability, it is sufficient to secure the swing at four points.
How to fix the seat
To mount the seat, you will need to provide the ability to attach the suspension, which can be done as follows:
- apply clamps of the corresponding profile, supplemented with a hook for the fastener element;
- make holes in the crossbar and install anchor bolts in them with a loop fixed at the end;
- fit bearings that are a secure fixing method but require constant lubrication to avoid annoying squeaks.
Directly the seat itself is suspended by a synthetic rope (climbing equipment), a chain or a metal cable (automobile). In this case, it is not recommended to use household appliances. If the option with a chain is chosen, it is necessary to use a product made of galvanized steel. A simple structure will rust, while painting it will be quite problematic.
The best seat material is wood. If a large seat is supposed to be installed, then a metal frame is required.
Bolt-on design
If it is not possible to use a welding machine, it is recommended to assemble the structure in the form of a letter P on bolts. To do this, you need a profile with a cross section of 60 by 60 mm. The choice of just such a product is due to the fact that it has greater strength compared to a round design. The supports should be about 3 m long, taking into account that about 50 cm will go into the ground to give the required stability.
The estimated height of the swing is 2 m. As for the length of the crossbar, there is a certain variability available, depending on how many seats are supposed to be installed and what their size. One frame allows installation of up to 3 seats. The material is the same - a profile with a section of 60 by 60 or 60 by 40 mm.
The crossbar is secured to the uprights with bolts, supplemented with locknuts and Grover washers. For this, using a special drill, the required holes are prepared, which are strengthened by thick metal plates installed from the inside.
To complete the installation, simply attach the seat to the suspension.
Swing in the form of a bench
The design of such rocking devices is somewhat different from what was described above, since in this case a large load should be taken into account. Such a structure must withstand not only a massive seat, which is a bench, but also the weight of several people. The supports are placed much wider here, and a thicker pipe is used as the struts.
For better comfort, a canopy can be built over the swing to protect it from the sun's rays, which can be made of wood, fabric or polycarbonate. Plus, soft pillows add extra comfort.
Manufacturing instruction
Almost any type of swing can be made on your own, as the process is fairly straightforward. We will consider a somewhat complicated version of the device due to the fact that it involves the use of welding. Such work is performed in a specific sequence:
- Cutting parts from pipes: side racks 2 m long, crossbars - from 1.5 to 2 m; preparation of 4 cylindrical products of arbitrary length, which are necessary for the assembly of the base.
- Grinding pipes with a file or sandpaper to get rid of burrs.
- Welding of structures for the base at right angles.
- Fastening the racks to the supporting part, then the crossbeams to the vertical elements using a special apparatus.
- Digging 4 holes at least 80 cm deep.
- Inserting metal beams into recesses with a length exceeding their depth.
- Filling the pits with a solution prepared from cement, crushed stone, sand and water, taken in a ratio of 1: 1: 2: 2. In order for the concrete to gain the required strength, you should wait a week and only then continue the installation work.
- Production of hooks for suspension by means of anchors with their subsequent welding.
- Connection of the assembled frame with metal beams sticking out of the ground using a special apparatus.
- Seat installation.
The second option for making a swing
Pillars
For greater reliability, the sidewalls of the structure are recommended to be made in the form of the letter A. But the frame can also be assembled from single products that serve for support, and the corners installed at the bottom give it the required stability. The most common option is considered when the base of pipes in the form of a rectangle is first welded, to which two triangles are attached, installed vertically, and a jumper, thereby achieving visual correspondence to the letter A. If you exclude the metal base, which turns the swinging device into a mobile structure, you need to take care about concreting racks.
Crossbar
The established triangles are complemented by a crossbar. The structure created in this way is fixed using prepared trenches or holes, observing the alignment in both planes. Then the recesses are poured with concrete, which needs to be given some time to fully harden.
Seat
The swing, oriented to adults, predominantly looks like a standard bench without legs. If such a device is intended for children, it is recommended to install a single or double seat.
Chains
Despite the fact that arranging suspensions from chains is an expensive pleasure, this must be done, since such structures are characterized by maximum strength, promote buildup and are caused by pronounced signs of wear, which allows you to notice critical wear in time. If the swing is aimed at children, you should suspend small-bore chains to eliminate the possibility of pinching your fingers.
Painting
The final assembly of the structure must be completed with the application of a special compound. This makes the assembled device more attractive and protects it from corrosion.
Rust converter
To prevent the destruction of metals, a rust converter is used, the application of which ensures the formation of a barrier film on the path of aggressive environmental influences. Typically, this compound is applied to the metal prior to painting.
Ball bearings for swing arrangement
With the help of ball bearings, you can create a structure that will serve for more than a dozen years. The use of these elements in the structure eliminates friction, which determines the durability of such structures, also eliminating the appearance of a squeak.
It is known that an A-shaped swing is the most optimal design, but it takes up a lot of space. We will consider the installation of U-shaped devices, the stability of which is given by the assembled support.
For work you will need:
- a pipe with a diameter of about 70 mm, required for the installation of the main structural elements;
- corner 20 mm for auxiliary racks;
- corner 40 mm for braces;
- an angle of 63 mm for fixing the crossbar.
After that, you can proceed directly to the installation of the planned structure, which involves the following set of actions:
- We dig in accordance with the markings 6 holes with a depth of at least 70 mm.
- We expose the support pillars strictly vertically using the building level. All parts of the structure that will be buried in the ground should be coated with bituminous mastic.
- We weld a horizontal support from a 63 mm corner.
- In the holes along the perimeter, we install the elements of the L-shaped section and weld them to the horizontal guide.
- Pour concrete into the holes.
- We proceed to the assembly of the assembly based on the bearings.
For mounting parts of the support, a 3 mm thick metal tape is used, which must be bent. Then a pipe is inserted into the bearings and scalded a little, taking into account not to touch the support elements themselves, as this can lead to their failure. The bearings are fastened to the belt by means of pieces of corners that are welded to a narrow strip.
The supporting pillars and the swinging parts of the structure must be spaced from each other at a distance of at least 50 cm. This need is due to safety requirements so that the child's hand does not get between these elements.
At the final stage of the assembly, it remains only to weld the rest of the structure, including the braces, which must be short enough to reduce the dimensions of the assembled device. The stability of the structure in this case is maintained due to the presence of a sufficient number of support points and the use of a 70 mm pipe.
Swing option on bearings
Let's break down the process of work on the arrangement of such a structure for swinging in stages.
Stage I
Frame fabrication. This will require pipes of 50 and 63 mm. First, a U-shaped structure is assembled from two products with a diameter of 63 mm and a length of about 3 m each, to which a cylindrical part with a cross section of 50 mm is horizontally welded. The diagonals of the resulting letter P must be the same.
Stage II
Fastening of bearings. To install the subassemblies, you need to cut 5 cm parts from a 90 mm pipe, and then insert the bearings into them and scald them, achieving a narrower diameter. This allows parts of the support to be retained in the pipe, which must be complemented by the welding of metal elements from the outside. After that, a 27 mm pipe must be inserted into the resulting structure.
Stage III
Holes for hangers and welding device. To the 27 mm cylindrical part, it is necessary to attach plates with holes for fastening the hook using a special apparatus. Then the assembled structure is welded to the crossbar of the letter P using small flat elements. This process requires caution as bearings are installed inside. The place of their installation should be lubricated with grease, and during the application of welding, water should be used for cooling to prevent damage to the subassemblies.
Stage IV
The finished frame is installed in prepared pits and concreted. The frame for the seat is made of a 20x20x2 mm profile pipe, which implies the use of welding.
Stage V
The resulting structure is refined with ground planks, which are fastened to the bolts. After that, the frame is attached to the chains by welding, and they, in turn, are suspended on the frame. To do this, you can use carabiners, which allows you to easily adjust the length of the chains.
Stage VI
Painting the assembled rocking device.
Today, a large number of people have country houses or summer cottages - places where you can calmly rest from the hustle and bustle of everyday life and relax. Today we will tell you how to make a garden swing from metal with your own hands for your summer cottage.
This material is conventionally divided into 3 parts.
- In the first part: the use of metal to build a swing, and why summer cottages prefer it. We will talk about the advantages and disadvantages of such structures, calculate the mass of the planned attractions, and also talk about the types of attachment for stationary and suspended swings.
- In the second part: we will tell you how to make a street metal swing for a summer residence in the form of a bench or a sofa with your own hands, we will also give recommendations for the installation of single structures. And you will also learn how to correctly make a seat for a swing from a profile pipe with your own hands, as well as a frame.
- In the third part: a little about decorating and caring for an iron swing, as well as the specifics of choosing in a store.
Advantages and disadvantages of a profile pipe
If you take a closer look at the advantages of a profile pipe, you get the following list.
- The shape of the tube is optimized for fast production, which means it is very simple and convenient to work with.
- A very economical material, especially when compared with reinforcement structures.
- Stiffening ribs that are located on the structure greatly increase the upper limit of permissible loads.
- The material perfectly resists mechanical damage - it is difficult to deform it with an impact.
However, along with the advantages, a swing from a profile pipe also has its disadvantages:
- Most of the operations that can be done on a pipe do not require sophisticated equipment. Except for one - flexion. It is very difficult to bend it, and all because of those very stiffening ribs. For this you need a special machine.
- Carbon steel rusts easily and lends itself to the destructive effects of moisture. This disadvantage can be eliminated using the galvanizing procedure, but it also greatly increases the price of the final structure.
Calculation of the profile pipe to determine the mass of the swing
When calculating the size of a metal swing, you should calculate its mass. This will help in the future to determine whether a foundation is needed and what loads the swing will withstand.
- When using a 20x20 square shaped pipe with a thickness of 1 mm, the weight of one meter of the tube will be ~ 600 g (it all depends on the steel grade).
- A 30x30 pipe with a thickness of 1 mm has a weight of 900 g, respectively.
- A 40x40 profile pipe with a wall thickness of 2 mm per 1 meter of length will weigh ~ 2300 grams.
Using the data provided, it is easy to calculate the approximate mass of both pipes and the frame of future garden swing from a profile pipe. We can do this as follows.
For example, the construction uses 8.5 meters of a pipe measuring 30x30x1mm and 3 meters of a pipe measuring 50x50x2mm. calculate the structural mass:
- 8.5 * 900 = 7650 g (total pipe weight 30x30x1mm);
- Since a 40x40x2mm pipe weighs 2300 g, a 50x50x2 pipe has a weight, respectively, 2300 + 2300 * 0.25 = 2875 g.
- 3 * 2875 = 8625 g (total pipe weight 50x50x2mm).
Purpose of a profile pipe for a swing
In order to correctly answer this question, it is necessary to explain what types of pipes for which parts of the swing are used.
- Round (oval) pipes. Suitable for curved structures (e.g. seats, armrests, arches).
- Square and rectangular pipes. They have good strength, suitable for parts that are placed on the surface (vertical posts, spacers).
- Flat pipes - suitable for auxiliary elements (horizontal spacers).
Swing attachment types and classification
Before choosing a scheme according to which we will assemble a metal swing with our own hands, you need to decide on how to attach them to the supporting structure.
There are two main types of swing mounts:
- on eye nuts;
- to the nodes.
In the first case, you do the following:
- Make through holes in the horizontal beam using a drill (~ 5 mm);
- Push in long bolts with washers, tighten the eye nuts;
- Attach carabiners and chains or ropes to them.
In the second case, the sequence is as follows:
- Throw the ropes over the crossbar;
- Making a sea knot;
- Attach the other ends of the rope to the seat.
Hanging metal swing
Homemade swing for a summer residence made of metal is often quite small. These are usually small seats for one person, mostly for children. They do not need a fixed base in order to hang them in the yard, they only need a tree with sufficiently thick branches or a supporting structure.
Hanging swings are most often hung on a chain or strong ropes - depending on the desire and style. At the same time, they can be fixed without damaging the branch itself: wrap the chain or rope with a sliding knot, which will provide a sufficiently strong grip. The main thing here is to correctly calculate the thickness of the suspension itself.
An example of a chain attachment. 
- Drill a large through hole 7-9 mm thick along the width of the seat (along the red line in the picture);
- Pull the chain through the drilled hole in the chain;
- Screw in the steel bolts along the edges of the seat so that the chain is secured.
Stationary swing made of metal
Do-it-yourself stationary garden swing from a profile pipe is a more complex option, but no less popular. Great if you need to install seating for two or three people.
For a stationary swing, in addition to the seat itself, it is necessary to make a frame from a profile pipe. This is the supporting element of the entire structure, the heaviest loads will fall on it, so it must be done with all attention. Fastening to a stationary frame has several varieties.
Where to install metal swings on the site
Before you weld a swing or buy it in a store, you need to choose a place on the site, we recommend that you adhere to the following rules:
- The swing should be located in an open area near the house. The ideal option is 10-20 meters, so that you can watch your children play;
- There should be no communications above the iron swing (water, power lines and other wires);
- There should be no roads nearby (it is best to put a fence around).
Having decided on the place, it is necessary to prepare a drawing-project of your structure. We recommend that you indicate all sizes in advance - this way you will save a lot of time and resources for revisions and alterations.
Swing in the form of a bench or sofa with a metal frame
This type of swing is common among manufacturers - today on the market you will find a large number of ready-made assembled models of this type. They are distinguished by their practicality and relative cheapness. Such a swing is suitable for joint gatherings in the evening after a hard day or on weekends with children and loved ones.
Before you buy materials and start making your own iron swing, check out the design features:
- this type of metal swing for a summer residence can be both portable and stationary;
- a foundation of a portable structure is not required - the support is a square at the base. In case you decide to make a stationary swing, we recommend keeping in mind the columnar foundation;
- a canopy is often made for such structures - it can be either a polycarbonate roof or a stretched awning.
Materials and tools
To make a swing from a profile pipe with your own hands, you will need a whole list of tools and materials:
- Round shaped tube for a frame with a diameter of 20mm, 14170 mm (take a meter or two more with a margin);
- 4 steel corners;
- 2 steel arcs, each 250 mm long and 15 mm in diameter;
- 2 wooden canvases;
- cable, chain or any other suspension that can withstand a load of up to 250-300 kilograms;
- welding machine;
- pliers;
- hammer;
- vice;
- grinder or hacksaw for metal;
- building level;
- roulette;
- special paint for metal against corrosion;
- eye screws 5x80mm, 4 pieces.
- lifting shackle М5, 6 pieces;
- bolt М6х30, 4 pieces;
- nut М6, 4 pieces;
- spring washer M6, 4 pieces.
Step-by-step instruction
 | Cutting parts from shaped pipes for iron outdoor swings. For the side racks, you will need 2500 mm segments, 4 pieces. On the crossbar, you will need a piece of pipe with a length of 2100 mm. |
 | We cut off the edge of the pipe at 30 degrees at the end, after which, using a welding machine, we weld them into an isosceles triangle. |
 | We measure 2000 mm from the top of the posts and weld on a horizontal bar 1035 mm long to strengthen the frame. See the drawing of a garden swing made of metal, which we made for you with our own hands. |
 | We weld the horizontal bar at the ends of the uprights. After that, the seat will be attached to it. The distance between the A-posts is 2000 mm, the crossbar protrudes 50 mm on each side. |
 | Let's start creating a swing bench from a profile pipe with our own hands. We take several bars 30x30x6000 mm and shorten them. You should get pieces of 1500 mm in the amount of 24 pieces. We clean them with sandpaper or a machine. Or you can take a 100x100 bar and adjust it to the required dimensions. It is not necessary to cut out 30x30, you can use 20x50 and 30x70, etc. |
 | We paint the surface to prevent wood from rotting. |
  | We make a frame from a pipe 15 mm in diameter. We weld the pieces together and attach the bars with bolts. The distance between them is 20-25mm. At the edges we weld the eye nut for fastening the chain (two on one side, two on the other). You can also experiment with the distance between the bars (it all depends on their size). More details on the drawing of a swing from a profile pipe. |
 | We attach the seat to the vertical posts of the metal swing frame. We drill through holes in the crossbar for bolts with eye nuts. We thread them and twist them. We connect the carabiners with all the eye nuts and attach the chain. |
 | We dig 4 holes 450mm deep. For this we use a manual iron drill. |
 | We mix concrete. Add cement, sand and water to the container in proportions 1: 2: 3. It is best to use a cement labeled M400. |
 | We put a 100mm sand pillow at the bottom, then we install the racks in the pits. We throw in a few large stones for the stability of the structure, after which we fill everything with concrete. We are waiting for 3-4 days until everything is dry. The construction is ready |
Single swing made of metal
Do-it-yourself single swing from pipes can be welded both stationary and portable - it all depends on who will use them and how much free space you have on the site. 
Stationary swings have the greatest stability of all the options listed: children will not be able to turn them over even during the most active game. However, because of this, they have a disadvantage - low mobility: they cannot be removed during bad weather. Portable ones, of course, are not as stable, but they are also much more comfortable than stationary ones. 
The main stages of installation
 | To weld the swing frame from the profile, you need to take a pipe and cut it into two equal parts, each 3100 mm. Cut the edges of the uprights at an angle of 45 degrees. After that, it is necessary to form the letter P - weld the third to the ends of these two segments. Its edges should also be trimmed at a 45 degree angle. |
 | The second step is to form a metal swing structure with your own hands on bearings. We need two pieces of 5 centimeters in length from a pipe with a diameter of 90 millimeters. Bearings are inserted into them, after which they are scalded to secure. On the other hand, for additional fixation, a small piece of metal is welded to overlap the pipe. A piece of pipe with a diameter of 27 millimeters will be inserted into the bearings. |
 | Two plates are welded to a 27 mm pipe - this will be fasteners for carbines. The structure itself for the bearings is fixed to the crossbar using two pieces of metal. They are welded to the sides of the pipe into which they are inserted into the bearings. It is important - before starting the assembly of this part, apply grease to the bearing and periodically moisten it with water. If this is not done, then the material will heat up from welding, the steel will begin to expand and the structure will be damaged. |
 | After the assembly of the frame is over, it is necessary to dig two holes under it, insert the ends of the pipe there and carefully concreting everything. After the concrete has dried, it is necessary to weld the stabilizing slopes from the remains of the pipes. |
 | A frame is welded under the seat of a garden metal swing from a prepared profile pipe. We use a welding machine. At the edges we attach the eyelet of the nut (marked with green dots). |
 | We attach the carabiners to the eye nuts and connect everything with a steel chain. |
How to make metal swing seats
Such a double swing from a profile pipe can often be found in playgrounds. First, a few words about the advantages and disadvantages.
Large metal outdoor swing Advantages:
- strength is the most important advantage of such a swing. Stiffeners greatly increase the bending resistance of the structure;
- cost-effectiveness - shaped pipes are easy to manufacture, which helps to significantly reduce the cost of all materials;
- durability.
Disadvantages:
- thorough care - if you do not galvanize the profile pipes and do not cover them with protective compounds, then after a while rust will appear;
- the complexity of bending pipes - this may require additional equipment.
We have already repeatedly told how to weld a frame for a swing made of metal with our own hands to a summer cottage, prepare the foundation and hang the seats, so now we will tell you which seat is suitable for such a design and its dimensions. 
The following parts are required: 3x1600m; 3x880mm; 2x200mm; 5x500mm. More details in the drawing.
A long segment of 1600mm is installed, 3 short ones of 500mm are welded to it - the letter Ш is obtained. Another long segment is welded from the free ends. The back is formed in the same way. Everything is fixed with corners at the edges of each part of the structure and welded together at an angle of 90 degrees. Two pieces of board are attached to the structure with bolts.
To make the backrest more comfortable to sit, you need to set it at an angle of 115 degrees. To do this, you need to make the appropriate section at the ends of the 880 mm sections for the backrest.
How to make a frame for a garden swing - video
To independently create a frame of a garden swing from a professional pipe, we recommend that you adhere to the algorithm of actions, as in the video below.
Decorating and caring for a metal swing
In order for the swing from the pipes that you made with your own hands to serve as long as possible, we recommend that you decorate them first and then tint them with special paint for metal once every six months or a year. 
Here's what else you can use to cover metal:
- rust solvent;
- enamel paint for metal;
- soil for surface treatment;
- paint with the addition of metal powder (yellow).
After the construction is completed, you can decorate the structure:
- Sew the seat covers. A dense fabric is suitable for them, which is not afraid of contact with moisture.
- Paint the side racks with patterns or drawings. To do this, you need a stencil with patterns or figures, paint for metal and a brush (or sponge). Place the stencil against the walls. Take a sponge and wet it with paint. Blot the stencil and remove. Repeat the procedure several times.
- Decorate the playground next to your homemade outdoor iron swing. Plant flowers, build a small decorative fence, arrange sculptures.
How to choose a swing made of metal
When buying a metal swing for a summer residence in a store, you should pay attention to:
- size and dimensions. As a rule, the swing has a width of 2-2.5, which is versatile and allows you to easily install it on any type of site. If unique dimensions are needed, it is best to custom-make.
- Manufacturing material. Decide in advance what kind of material you want to see. The classic version is made of metal and wood, but there are also modern materials, such as high-strength plastic, steel rods.
- Price. This is an important factor, since on the market you can find absolutely any model for a different budget.
We offer to consider several models of single and double metal swings that are now popular on the market:
| Model | Price | Manufacturer | Main advantages and features | ||
|---|---|---|---|---|---|
 | 8 990 RUR | China | 1.9x1.13x1.8m | up to 300 kg | ● double swing; ● soft seat; ● fabric canopy. |
 | 3 710 RUB | Russia | 1.37 x 1.42 x 1.8m | up to 90 kg | ● single swing; ● the bases of the product are installed in concrete; ● wooden seat with chain attachment. |
 | 6 890 RUR | Russia | 3x1.2m | up to 100 kg | ● double swing; ● wooden seat; ● fastening - steel chain; ● without foundation |
 | 12 990 RUR | Russia | 2.9x1.55x2m | up to 250kg in total | ● double swing; ● seat material - plastic; ● suitable for children 3-10 years old; ● material of manufacture - steel |
In conclusion, I would like to say that regardless of whether you want to assemble a metal swing yourself or purchase a finished product, you must first of all look at their quality and ease of use, choose only the best. We hope you now know how to do this. Good luck!
Swings in the country or in the courtyard of a private house are quite common. This is not surprising, because both adults and children love to swing in the fresh air. When making a garden swing from metal, you can enjoy both the process itself and the result of the work done.
There are a lot of swing varieties: made of wood, car tires or a cable tied to a tree branch. However, the most reliable and durable construction is, of course, metal. For the manufacture of children's rocking chairs and hanging benches for the whole family, square profiles, corners, pipes, T-beams or I-beams are used.
Thematic material:
Overview of metal structures
In such products, the frame can be:
- welded;
- collapsible.
To manufacture the first option, special equipment and skills in working with a welding machine are required. Such supports are distinguished by their strength and rigidity, which will allow the garden swing to be used for many years without risk to health.
But to assemble the frame with nuts and bolts is available to everyone. But it must be borne in mind that over time, threaded connections loosen under load, play appears, and the swing can collapse and injure a person. They should be reinforced with locknuts and grovers, periodically tightened with a wrench.
Photo: frame dimensions for installing a swing
According to the configuration of the supports, they are distinguished:
- frame in the form of the letter "A" - two crossbeams, connecting from above and having a jumper for greater rigidity (there are L-shaped structures);
- supports with a crossbar, connected in the form of the letter "P" - a more unstable option, but less laborious and lightweight in execution. If you bury the supports deeply and concrete with high quality, such a swing will be suitable for use.
Still all metal "attractions" are divided into:
- stationary, with concreted supports;
- portable, fixed with anchor bolts, bent reinforcement, driven into the ground.
Dimensions of the garden swing: frame height 2100 mm, height from the ground to the saddle 700 mm, width 1400 mm.
Swing for babies up to 6 years old
The small weight of children makes it possible to make simple structures, which, as a rule, are assembled from a pipe with a diameter of 50 mm or more. A drawing is preliminarily drawn up with the applied dimensions of all components.
A design in the shape of the letter "L" with a height of 1.5-2 meters is suitable for children. It is better to make it portable; for this, a base in the form of a square is welded to the bottom of the supports.
A metal rod is clamped in a vice and bent in the shape of a hook. The length of such a pin is equal to one meter, of which 50 cm is driven into the ground. Four fasteners are sufficient to stabilize the product and prevent it from tipping over.
Photo: children's swing from a metal profile of a round section
Garden swing for older children
Such structures must withstand heavy loads. The posts of the supports are welded at an angle and additionally fixed with a horizontal lintel at the level of 1/3 of the ground. Then a crossbar is attached to them. This can be done using a special blank made of three pipe sections, where the edges of the supports and crossbeams are inserted.
When working independently, it will be easier to do this:
- Weld a triangle from the plate to the top of the posts, make a hole in it.
- Cut off the head of the bolt with a grinder, the diameter of which is slightly smaller than the size of the crossbar.
- Insert this stud into the pipe and secure with a bolt connection, having previously drilled a through hole in both parts.
- Pass the end of the stud into the triangular blank welded to the uprights and tighten with a nut and locknut.
The supports are concreted. For this, holes are made with a drill in the ground with a depth of 40-50 cm, rammed, covered with sand and gravel. Pour in concrete. Leave to dry for a week.
Photo: anchor hook fastening diagram. Be sure to lock the nuts.
Seat fixing options
To hang the seat, you need to fix a special device:
- clamps of a suitable profile (round, square) with a hook for hangers;
- you can also drill holes in the crossbar and thread anchor bolts with a loop at the end to attach a rope or chain;
- the connection with bearings is the most reliable, but requires constant lubrication, otherwise a squeak cannot be avoided.
The seat is suspended on a synthetic rope, chain, metal cable with a cross section of 7 mm or more. A rope for transporting a car or a cord for equipment for climbers will do. The chains will rust when exposed to the environment. It is problematic to paint them, it is safer to take galvanized ones.
The seat is best made of wood, which is warm and pleasant to the touch. If the drawing provides for a large seat in the form of a bench or chair, the seat is reinforced with a metal frame.
Threaded design, no welding
Those who do not know how to work with a welding machine can make a U-shaped base on threaded connections. For pillars, profiled square pipes of at least 60 × 60 mm are used. They are more stable and durable compared to round ones. The length of the supports is up to three meters, while 50-60 cm are concreted in the ground.
Option for attaching the crossbar to the uprights using bolts
So, the height of the swing will be 2 m. The length of the cross member depends on the size of the seats and their number: up to three seats can be suspended on one frame. The material used is the same 60 × 60 or 60 × 40 mm profile. Drawings of such a swing are quite simple and straightforward.
Connect the crossbar to the uprights with bolts, using locknuts and grovers. Holes are drilled in it for fasteners, which are reinforced from the inside with thick metal plates.
It remains to hang the seat on a chain or cable - and your home garden "attraction" is ready.
Swing benches
Drawings of such a swing provide for some differences: the supports are wider, the fasteners are more powerful, the pipe is thicker. After all, they have to withstand the weight of a massive bench seat and several people.
Drawings of swing analogs sold in garden stores
To hide from the sun's rays while relaxing, a canopy is made of fabric, wood, polycarbonate. The lower it is set, the more shadow it will cast. A comfortable hanging garden bench with soft cushions.
Making a swing yourself is easy. This will require inexpensive materials, some tool skills, a drawing and, most importantly, desire.
Photo gallery of finished products
