With him we do not spend time looking for tools in the garage or workshop. They are always at hand, because Stored in a wall closet for tools that are made with their own hands. Lighting the workplace is provided by the lamps that are attached from above the central section of the cabinet. It has strength tools. The cabinet itself hangs on the wall due to beveled straps.
Materials
- Side walls, 2pcs, 1220x100x25, pine
- Cover, 1pc., 1220x100x25, pine
- Bottom, 1pc., 1220x100x25, pine
- Shelves, 3pcs., 1220x100x25, pine
- Partitions, 4pcs., 100x100x25, pine
- Side walls of doors, 4pcs., 1220x75x25, pine
- Hanging jumpers door, 2pc., 610 × 75-25, pine
- Lower lintels door, 2pc., 610 × 75-25, pine
- Rake-limiter, 1pc., 1220x12x12, pine
- Door shelves with grooves, 2pcs, 610x75x25, pine
- Reiki for edging edges of the shelves of the cabinet, 3pcs., 1220x12x12, pine
- Stirred storage bar, 1pc., 1220x50x50, pine
- Rear wall of the cabinet, 1pc., 1220x1220x12, plywood
- Front walls of the door, 2pcs, 1220x610x12, plywood
- Boards for fastening the cabinet to the wall, 2pcs, 1220x100x25, pine
Cabinet manufacture
Phaneru, 12mm thick, we saw circular in half. It will be the rear wall of 1220x1220mm. We are kpripim 2 lateral walls with glue and 30mm screws. From the board, cross section of 100x25mm, drink the lid and bottom. Confirm them to the rear wall with glue and screws. After that, we fasten the ends of the sideways with screws 4x50mm with the buttons of the bottom and covers, the top and bottom, I use 2 screws to the joint. We remove the adopted glue, we clean the protrusions.
The remaining Phaneur is cutting on the door for the door, the size of 1220x610mm. Next, we scream 4 side walls of the doors with a size of 1220x75x25mm and secure glue and screws to the front wall. The upper and lower jumpers cut the size of 25x75x610mm, fastened in places. Next, we fasten the horizontal and vertical parts of the door, using the screws 4x50. For each joint - 2 screws. Store massive, heavy tools in the main section. Shelves size of the central section 1220x100x25mm. We place them optimally in the central section and glit at the place. Through the side I. rear walls Outside, kpripim shelves with screws additionally. We drink the grooves in the shelves on the locker doors for screwdrivers and other long tools. Other tools that have closed handles (for example, hacksaw), store on wooden bars. We make these bars as follows: Drink a bar on the inner contour of the bar and a plywood from plywood with a thickness of 6mm. Breeping to the door of the bar of two screws, and to the bar - a junk.
To the central section, secure the door loops. On top and bottom Breeping on the left door of the spiing. For them, choose the nests in the bottom and in the upper shelf. Confirm the handles and hang the castle to both doors. Move the cabinet to the wall on the horizontal strips, which are attached with screws 65mm long.
The idea itself spinning in my head for quite a long time, but since it was not required material, I had to constantly postpone its implementation. But after the construction of these shelves and racks, there are quite a lot of diverse screens of chipboard. Actually, after that, I decided to put a small box in the instrumental cabinet so that he would push if necessary, that is, was on the hinge. Initially, it was the usual wall cabinet in the apartment, converted over time to the instrumental. It would be possible, it was stupid to drill in deep shelves from a distance wall, to the door itself, and no longer steam. But deep shelves have one big minus, they eventually climb so that it becomes hard to get to a long corner to get something very necessary. And according to the law of meanness, everything necessary, as a rule lies in the far corner.
Therefore, in this closet, I decided to simply hang a lot of small and not very deep shelves for a specific tool or material. On the pictures below it is clear that it turned out. Inspired them in the middle part of the cabinet, mainly under the bolts, self-tapping screws and power tools so that there are big retractable ShelfAnd under it compressor compressor and paint. Also, along the edges of the cabinet, a pair of backlight threads were built, which is included when opening the door.
In the photo below, it is clear that after this upgrade, there was an unused emptiness of the Cabinet Surride. Here is this place, I decided to attach a small pull-out drawer, thereby increasing useful Square For a variety of instrumental junk.
This is actually the scraper of the chipboard of which I will collect the box.
Something like it looks like this. Twisted on ordinary self-tapping screws and iron corners.
It was assumed to take him aside as the usual door. But since this box will be located somewhat deeper, relatively door box The cabinet, it was necessary to build these loops so that with their help it was possible to push the box from the closet.
Actually, the box already fastened on its place. At first glance, everything seems to be wonderful, but it was worth opening it as all these loops began to go on a break. And in the end, this box hung on a diagonal and this is given that it has not yet been tool.
In general, I had to abandon these furniture weets and ask friends, cook something more powerful. As a result, it turned out such a loop of thick sheet iron, rounding, nuts and corners, on which you can now boldly hang, and she will not even get drunk :-)
Since the whole mass of the drawer with tools will fall on low part This hinge, then in the top of the hinge, the corner is made of a thin strip, for the load is minimal there.
Here the cardboard pattern is visible in which the sizes of the hinge are measured so that the box can freely dive into the closet.
The base of the sheet iron was cut out, on which the boxes will rotate.
We carry the mark of the hole under the pin, from the cardboard template on the iron sheet and drill.
After that, we screw this piece of iron to the base of the box.
At the end, slightly smeared with solidol all the fuel surfaces of this hinge, put this box on the pin of the lower support and secured it by bringing the top edge of the loop, to the drawer. On this powerful loop, the box is now easy and without special efforts, rotates in one finger.
On the back of this box, screwed fragments of galvanized strips, which perform the role of spring-loaded holders, while holding the oversized tool in a variety of wooden trees and metal.
A little video in which this box in action.
Unfortunately, it was not yet possible to finally sip this box, embedding a variety of cups and cells for horn keys, screwdriver, rolling, hammers and other tools, for the way to open this box broke out with time. The idea itself is not bad, but only if the door opens rarely or automatically. And so, with some insignificant repair in the apartment, sometimes you have a dozen times, it is to see this wardrobe and lose the drawer from it :-) Now there are plans to transfer this box to the door so that when you open only one door when you open only one door, The whole tool would be, as on the palm, that is, in one way of hand. But for this you need to change the door itself, since this very old, loose (chipboard), is slightly curved and with weak loops.
Almost every man in the house or in the garage there is a set of tools. Consequently, keep them in perfect order. How best to do it, tell new Overview. Surely everyone can find in it who were interested in his examples of the organization of storage.
1. Plastic cans
Cropped cans perfectly suitable for storage of nails, screws, bolts and buckets. And in order not to dig for a long time in search of the necessary, containers are better to march.
2. Wooden shelf
Narrow wooden shelf With holes - a wonderful storage space for screwdrivers.
3. Stand
So that the pliers are not scattered throughout the garage, make a special special for them. wooden stand.
4. Reiling
Slim metal rod perfectly suitable for storage paint brushes in suspended state.
5. Separate cells
From residue PVC pipe You can make comfortable cells for the gentle storage of a small power tool.
6. Wooden stellage
Homemade wooden stellage For storage spanic keys Let me forget forget about the disorder and tedious search for the desired tool.
7. Open locker
Open wooden locker as it is impossible better suitable For storage aerosol colorswhich most often happen chaotically scattered in the garage.
8. Mobile stand
A small stand on wheels is perfect for storage hand tool. Such a rack is very compact and will always have required tool at hand.
9. Wooden stand
Stylish wooden bench with a shelf that is suitable for storing the set of most different tools. Such a product will help not only streamline the hand tool, but will become a real decoration of the male monastery.
10. Homemade Stand
Unnecessary pallet can be turned into comfortable stand For storing garden inventory, which often takes a lot of space in the garage.
11. Hanger
Plain wooden barber Metal hooks will make it forever solve the problem of storage of the power tool.
12. Handbags for clothes
Non-good manipulations with an ordinary clothes hanger will allow it to turn it into convenient organizer For storage isol and scotch.
13. Storage system
Forks, shovels, rake and other garden tools Not too stable and also takes a lot of space in the garage. Reliable wooden hooks on the walls will help competently place a garden inventory along the garage or shed walls.
14. Folding table
Homemade folding table From wood and wall shelving for storing hand tools - a stunning idea for a small garage owners.
15. Glass cans
Ordinary glass cans from metal covers Perfectly suitable for storing various trifles. For greater convenience and reliability, the cans can be screwed to the shelves.
16. Vertical storage
The usual average garage looks very climbed. The competent organization of storage systems will solve this problem. Instead of the next cabinet, equip the walls with various shelves and hooks, which will allow you to carefully place a lot of things starting from the tool ending with a huge boat and bikes.
17. Magnits
Magnetic tape or individual small magnets - great idea To store bits for screwdrivers, drills and other small metal parts.
In continuation of the topic, let's tell about anywhere.
For each man, his set of tools is pride and treasure that needs to be carefully stored. To the tools are in order, it is best to purchase a special box for them. It looks decent, performs its functions 100 percent.
However, not everyone can afford it. In this case, we recommend that you make your own hands for tools. It will not take long time, but will bring satisfaction from the fact that you coped with the problem without excess costs.
Before starting work, you need to take care of materials for work. To construct a cabinet for tools at home, you will need:
Important. Do not use Phaneur as a bottom for boxes. Plywood lists There are no durability, so they will not be able to withstand a lot of weight.
Scheme and drawing
To collect a high-quality cabinet for tools at home, do not do without good drawing. You can create a drawing yourself, but it is better to find a finished sketch on the Internet.
Creating a wardrobe for own needs, It is not particularly bored, carefully drawing a design, but only draw a modest sketch. Pre-determine the sizes of the rear and side walls, as well as pay attention to the size of the lid and the pallet.
Council. Planning the shelves, do not forget about the thickness of the boards, which "destroy" some of the free space.
Messenger pick the boxes under the size of the shelves (minus 5-6 mm for freedom of movements). Boxes strongly advise the removable, which will make it easier to work with the tool. Best of all, when designing, planning the placement of tools in drawers in one row and one layer. It will make the job more comfortable, and will also create a shallow locker.
Tools and fasteners
To create your own tool cabinet, you will need:
Council. Galvanized screws are suitable for working with a wood screwdriver, and not steel. Their characteristics are the same, but the steel stand is more expensive.
Application of nails when collecting construction is not recommended. It is no secret that the tree will eventually dry, and nails will not be able to provide sufficient strength.
Assembly
The initial stage of the assembly of the cabinet - creating a carcass. Collect the frame from the boards, as mentioned above. The boards should be poured by certain sizes indicated in the drawing. The side walls, the bottom and cover are harvested from the boards.
Council. Check that there is no broad slot between the boards.
For assembly it is necessary:
Congratulations, the frame with the shelves on this is completed!
Next stage - creating legs. To do this, the bar is attached to the bottom of the carcass (only on the reverse side), as if it was attached. You can not worry about too durable fasteners - it's enough to take cheap screws. After that, prepared pre-legs are attached to them in the corners.
Final stage - boxes. They are created by hitting the framework of the desired form and size. The bottom is attached to this frame. If necessary, add shelves with inner They make propelles, where partitions will be mounted.
Photo
The following photos will give ideas for inspiration:
Useful video
On the next video You can see all stages of manufacture
Conclusion
As you can see, spending not so much strength and minimum of money, you can create a practical and inexpensive box for tools with your own hands. A large plus of such a product compared to the purchase - you yourself can "fit" the locker under your needs. The tool box made independently will not only allow you to streamline the tools, but also give reason to be proud of yourself and the work done.
In contact with
3827 0 0
Tool cabinet: selection and assembly of furniture for workshop
The cabinet for the tool is a mandatory attribute of most workshops, garages and production premises. Having placing industrial furniture, you can store the instrument in proper order and, it will always be at hand. In this article, you will learn which modifications of instrumental cabinets have received widespread distribution and that from this assortment can be collected by yourself.
Construction features of cabinets
Structurally, all industrialized wardrobes can be divided into the following categories:
- All-welded. Such structures are harvested from sheet steel without a carrier frame. Constructive elements fight with a solid seam over the line of the joints.
Such a technology is used for the manufacture of low and medium-wide stationary modules. To increase strength on the structural elements, firewalls can be performed that work as ribs of rigidity.
- Collected. These designs, like all-welded analogs, are collected without using power carcass. Constructive elements are connected to each other with bolts, nuts, washers and other hardware.
Application of such technology is justified for the small-sector handicraft production. Ready-made prefabricated cabinets when less strength It is more expensive than welded counterparts.
- With carrier frame. This technology is used in the manufacture of stationary and mobile structures with high resistance to mechanical loads. The basis of such cabinets is used frame welded from profile pipe or corner. On top of the frame, structural elements are boiled out of a metal sheet.
| Illustrations | Varieties of cabinets according to mobility |
 |
Mobile. Mobile devices are made in the form of a wheel trolley, on top of which the box is fixed. Given the significant load on the design, mobile cabinets in comparison with stationary analogs have a tougher enhanced layout. For convenience and safety of operation, mobile structures are equipped with handles and brake systems. By blocking the wheels, the design is securely fixed in place and is used as a stationary cabinet. |
 |
Stationary. Non-edent stationary cabinets are metal frame structureswhich are installed on smooth base Paul ( outdoor option) Or hang on the wall (mounted layout). |
| Illustrations | Variations by way |
 |
Outdoor. The sale provided modifications with sash, with drawers and combined options. |
 |
Suspended. This category includes cabinets designed to load up to 200 kg. The weight limit is due not to the low strength of the product itself, but the density of the wall and the strength of the suspension. |
Functional "filling" of instrumental cabinets
| Illustrations | Varieties by method of operation |
 |
Instrumentation warehousing systems. This category includes cabinets that can be used only for storing the tool. For these purposes, internal shelves, drawers, suspension stands, and the like are provided in the construction of the structure. To ensure the safety of the tool door sash Equipped mortise castles or external loops under the mounted castle. |
 |
Wardrobe workbair (instrumental module). These are multifunctional facilities that can be used both for storing the tool and for operation with these accessories. For these purposes, the construction is arranged so that the storage boxes are located at the bottom, and the metal countertop was fixed on top of them. Optionally, a vertical perforated suspension stand is installed on top of the structure for temporary placement of a non-heightened tool. |
Tool cabinet manufacturing material
| Illustrations | Materials and their description |
 |
Metal (iron). Sheet steel is the most common material for the manufacture of instrumental cabinets. To assemble the housing, steel is used with a thickness of up to 0.8 mm, for shelves - from 1 to 2 mm. To enhance the design, the power is applied baking frameAlso assembled from metal.
|
 |
Tree (from plywood). Multilayer plywood and sawn timber is rarely used for factory making instrumental cabinets. Products based on sale are either produced by small series, or manifests. Wooden structures are preferably used for storing carpentry accessories. |
 |
Chipboard. Woodin stove is used exclusively for the manufacture of instrumental cabinets with their own hands. In designs from chipboard, it is preferable to store small weight accessories, such as a carpentry tool, electrical engineering repair equipment, etc. Folding into the cabinets from chipboard of plumbing accessories, high likely to damage the shelves or leave the chips on the veneer. |
The location of the instrumental cabinet in the house and apartment
| Illustrations | Cabinet location in living conditions |
 |
Garage. If there is a car, without various tools And do not do the components. And the more the tool will be in the garage, the less ruining will be the operation of the car. Since maintenance facilities need a lot, you will have to provide a place to store them. For components of a large size, such as wheels, a sufficiently open rack, but for keys and other small equipment can not do without closing boxes. |
 |
Parishion. Is there not enough space for the workshop? The workshop can be equipped in the hallway, separating the part of the cabinet at the entrance to the tools and other accessories. The photo shows interesting example The part of the wardrobe is equipped under workshop and equipment. |
 |
Balcony. Many for the absence of other premises, equip the workshops in the balconies and for this, how can it be used by the instrumental locker. Of course, massive metal design Factory production to drag on the balcony will not be easy. But the homemade locker, assembled from boards and plywood, will not only succeed at the balcony, but also will not give an excessive load on the overlap. |
Tool cabinet: do it yourself, drawings and schemes
You found out what could be a cabinet for the tool and nevertheless you do not intend to buy the design of the factory assembly? In this case, you will probably become interested in ways. independent manufacture Systems for storing tools.
If there is no time and desire to collect something from scratch, a good cabinet for storing the tool can be made from the old wardrobe or from the non-working refrigerator.
Overview of assembly projects
An independent assembly is starting with the development of the drawing. The designed cabinet must meet two requirements - it must match functional purposeAnd it should be easy to assemble. The simplicity of design is especially important if the manufacture of industrial furniture you do for the first time.
For the manufacture of the cabinet shown in the drawing, sheet steel with a thickness of 0.8 mm is used. The design of the reinforcing frame, assembled from an angle with equal shelves.
Collect the frame preferably using welding equipment. The outer covering can be mounted with a cloth or bolts with nuts. Shelves in the project are not provided, as the furniture is designed to store the large-sized tool.
On the proposed drawing, the most common version of industrial furniture, which will have to be manufacturing enterprise or in the garage. Large distance Between shelves - 49 cm is enough to install boxes with small-scale accessories and for storing full-size tools and parts.
The wardrobe is large, and therefore, a weld frame applied to ensure the rigidity. The frame cover is performed by sheet steel.
This is very interesting optionwhich will be discontinued by craftsmen wishing to organize a workshop on the balcony or in the hallway. The design shown in the figure is produced serially and can be purchased ready. Nevertheless, there is nothing difficult in this furniture that could prevent her on their own.
The advantage of the design shown in the drawing and the figure is a folding panel that can be used as a workbench. In the collected form, the furniture practically does not spend free space, which is important for the arrangement of small-sized premises.
A tabletop with one edge by means of hinges is attached at the bottom of the cabinet while the other edge relies on the folding stand. In the wardrobe, the suspension stand is used on which you can accommodate most Tools from a domestic workshop.
In the factory execution, the design is assembled from sheet steel. But instead of the metal, you can use Paneur and frame from Bar.
What can be done yourself
Do not having a metal hardware, a simple tool storage cabinet can be collected from multilayer plywood or from chipboard.
Like the usual cabinet, the tool repository is a rectangular box with horizontal guides for which boxes are moving.
When planning the stands, we take into account the main size - height. Ideally, the finished furniture should get a little higher than the belt. Then the end will be used not only for storing the tool, but also as a desktop. The width and depth of the furniture is selected taking into account the location.
An important point is exterior finish Cabinet. Since the furniture is designed for operation in a workshop in an apartment or a garage, I recommend using not laminated for the assembly, and the painted chipboard.
Plastic veneer is easy to damage, carelessly knuckled with a metal tool. Again, the price of laminated and veneered chipboard is higher than the value of the injust-made plates. Therefore, it's easier to assemble a tumba from ordinary chipboardand then primed and coat with multiple layers of wear-resistant paint.
Let's summarize
Now you know what should be a closet for storing tools and how to make it yourself. If you have questions about the choice and assembly of industrial furniture, write about it in the comments to the article.