Doors with a festival: design features. Doors Volkhovets with a festival - Products with high insulating characteristics Door with outlook

"Cold" metal? Or "warm" tree?

What do you think, in the last couple of years, has so much increased the trend of installing warmed inlets from a tree?

Who built their house 5-7 years ago, will give an answer right away, because they themselves collided with the fact that iron doors do not cope with Russian winter.

It is absolutely no important which company manufacturer, what the cost of the door, one serious problem arises.

With the onset of winter, by contour metal door, water appears, and in frost ice growths, as in the old freezer.

Because of which?

Metal has a great thermal conductivity and therefore in winter on the inside of the door, the temperature of the metal near zero or even loweralthough you have +24 in the corridor.

And we do not sit at home round days.

Coming from the street, the shoes will be snow that melts, and after evaporating condenses on your entrance door.

All the water in the end flows into the floor or snippets through the slots in the door itself.

What is scary?

But after 2-4 years, enamel from your door will disappear due to the corrosion that appeared.

Rusty doors do not look very beautiful.

Input warmed wood doors - the only alternative to metal doors

Nothing stands in place, technology and opportunities will always go ahead.

Over the past 3-4 years, appeared great amount The innovations were created a lot of new components, using which, we make the doors are more reliable, more beautiful and more convenient to operate.

Each industry has cheaper goods, there is more expensive, the search for compromises takes no little time. We are ready to offer you three worked series of warm entrance doors with from the outlook.

Basic information:

1. Material is an array of pine. You can also make from valuable wood (oak, beech, ash), check more than
2. The thickness of the canvas - 80mm and 100mm
3. Number of contours of seals- 2 and 3 loop sealing circuit
4. Interior filling - PPU or PENEXK.
5. Block size - any. 90% of cases under the size of the opening
6. Coating - or shelled, paints on the RAL catalog, or not hiding, dye + varnish. All paint products for outdoor work.
7. Appearance - any model from the catalog
8. Manufacturing time- from 10 working days

The cost of the door block with block size (box size finished product) up to 1000mm in width, up to 2100mm in height and with a box to the depth of 105mm

	"Standard" series	Series "Baguet 80"	"Baguet 100" series
License thickness	80mm	80mm	100mm.
Box width	105mm.	105mm.	120mm
Number of contours seals	2 contour 18mm width	2 contour 18mm width	3 contour 18mm width
Type of canopies and number	3D detachable loops with adjustments
Furnitura	Castle Guardian 10.11, pen, lining	Castle Guardian 10.11, pen, lining	Calley Callea 252RL, pen, lining
Heater inside the canvas	PPU 10-30mm	Polyurex 40mm	Polyurex 40mm
Installation of glass package	impossible	possible without a markup	possible without a markup
Manufacturing time	about 20 working days	about 10 business days	about 10 business days
Costaboutfor block	35,000 rubles	45,000 rubles	62500 rubles

If the dimensions of the unit exceed 1000 * 2100mm, then the markup is 10% for exceeding 1 plane (or width or height) and 15% if excess in two planes.

Additionally available to order:

- Good to any depth of opening(wall thickness) cost 150 rubles For each centimeter over 110mm. Example of calculation: Wall thickness 230mm, 230mm-110mm \u003d 120mm / 12cm. 12cm * 150 rubles \u003d 1800 rubles Cost of good

- Coolbands of the following sizes:

• 70mm - 850 rubles on one side / 1700 rubles from two sides
• 90mm - 1000 rubles on one side / 2000 rubles from two sides
• 120mm - 1350 rubles on one side / 2700 rubles from two sides
• 140mm - 1600 rubles on the one hand / 3200 rubles from two sides

- Additional castle Under the Suwald key 1000 rubles or under the cylinder mechanism 1500 rubles

Replace the main castle on Calle Calle 252(Suwald Key) - 2000 rubles

- Setting 3D loops with adjustments - 3000 rubles

- Night watchman - 600 rubles

A complex model from the catalog, or by sketch from 1500 rubles

- Painting on both sides in different colors - 1000 rubles

Braching - 2500 rubles

Threshold from oak - 2000 rubles

- Protection of the threshold of metal - 500 rubles

- Painting according to the catalog of the Ral - 1500 rubles. Bright and rich colors (yellow, red, blue, etc.) may differ in price.

Details about the series of inlet warmed doors:

The larger the distance between the contours of the seal, the better defense from freezing

All series of doors are manufactured with "Icedlav"

What is "flood"?

This is a profiled door element designed to install a sealing circuit that lies on the plane of the box, thereby closing the clearance in the focus.

Why do you need this "flood", and what kind of sense?

First, he fully closes the gapon the perimeter of the door, the wind does not bloom there, water or snow does not fall. The entire thickness of the canvas is running from freezing. Fittings and coating are fully protected from the environment.

Secondly, it allows you to locate the contours of the seal at the maximum distance from each other.

Third, in the doors with "Icedlav", light opening inside the box does not decrease, due to an additional quarter under the second contour, as in the exclusive options. These are the most centimeters-two that lack width when it is necessary to render a new oven household appliances or furniture.

You can still specify in the fourth, fifths, and so on, but there is no point in this.

Series "Standard"

This series is a standard solution not only with us, but also most of the other manufacturers, where the door canvas is first going, and then it turns entirely.

Pros of this series:

Any model from the catalog

Possibility of manufacturing different models Outside and inside

Affordable price

Cons of this series:

Only deaf execution

The inner part of the door, as well as the nodes of the adjuncing elements remain not painted

Manufacturing time

An example of the input warmed doors of the "Standard" series:

The main differences from the "Standard" series can be allocated two:

1. Doors are made with a bagent frame, with which the door not only looks solid and richer, but also allows each door element to paint separately. The baguette frame is hardly attached after painting with hidden fasteners without damage to the varnish layer.
2. Element painting. All elements of the canvas are first swaying, and then the canvas is going.

Pros of this series:

Execution of both deaf and double-glazed windows. Double-glazed windows can be installed up to 60mm thick

All elements of the canvas, as well as the adjoining nodes are scratched, the impact of moisture on the tree is minimal.

Manufacturing time

Appearance

Cons of this series:

Not every model can be done. There is no possibility of manufacturing from different sides of different models.

Cost

To order available the following models From our catalog: "Classic", "Classic +", "Dominic", "Adele", "Classic", as variations of these models with strict vertical and horizontal lines.

An example of the inlet warmed doors of the "Baguet" series

Talk a little about conclustede Lyakh.

I think you noticed that we use 2 types of seal, both groove and both 18mm wide.

For the outdoor circuit, thin, 3mm in the gram, seal is used. Less square interaction with environmental, More Snow / Water / Wind / Cold Protection

For the internally circuit, we specially developed and ordered a silicone tubular groove seal D profile. This seal has 4 mm, which provides 100% adjacent internal contour to the plane of the canvas.

The estimated service life of seals 50 years.

What cannons we offer?

To date, the choice of hinges for doors with from the outlook leaves much to be desired. And they can be divided into 3 types:

1. Scratched. Approximate load 30kg per loop. Possess adjustments, but there is no anybody resistance.And in a year or two canvas saves. Better put on interior doors
2. Overhead. Such put on the input aluminum and plastic doors. Reliable, adjustable, with a load to 50kg per loop, but very ugly.
3. Currency. We install data on our doors and their only two types. Below comparative table:

	Palladium 401, three loops that installed in the database on the doors with 80mm flat	3D loops loops, basic replacement loops on 2 loop data +3000 rubles
Color	Gold, chrome, bronze	white, matte chrome, chrome, matte gold, gold brown bronze
60/90 kg	120/150kg
Adjustments	not	There are in 3 planes +/- 2.5mm
Production	Factory China	Europe
Detachable loops or not	Not	Yes
Maximum width of the seal from the loop	12mm.	18mm.
Does the sealer teest loop mounting to the canvas	Yes	No, the seal forms a closed contour around the canvas
Features		Larger opening angle due to loop design Gapfrom the castle,betweenflat and boxcan be increased5mm, by adjusting loops

Palladium 401.

Summarize. 3D loops are much advantageous in relation to basic loops, but the cost of the loops themselves are several times higher. On the door blocks With a web 100mm and from valuable breeds, the loop data is installed in the database

Loop 3D required to be installed on:

Door block height above 2200mm

Door block width over 1050mm

Door blocks, where the calculated weight of the canvas will exceed 80kg (for example, setting forged lattices)

Examples of the doors manufactured by us and their elements

Brash + oil painting	Braching + complex color with patina	RAL 1013 painting + painting
Input groups of various configurations		Braching + complex color
Kale 252 RL Castle	Kale 252 RL Castle	Budget Options input warmed doors Why are iron doors freeze? This is pretty frequent question And now we will briefly consider it. Standard Equipment of the Entrance Door On the sketch, we see that the box that the canvas in the focus consist of iron that creates a closed loop that contacts both the street and with the room. Although the thickness of the metal is not particularly large, but the difference in the thermal conductivity of the insulation inside the door and the metal itself differs in 650 times! Whatever thickness was the rail door, metal around the door perimeter, it will freeze, it is physics. Does all iron doors imitate? From producers iron doors The issue of freezing the entrance door is sharp and they are looking for a solution. It is not difficult to guess that the doors would not be frozen, it is necessary to do so that metal from the side of the street did not contact the metal indoors with the metal. Exclude any cold bridges and make a thermal survey. Moreover, the thermal survey should be both on the canvase and on the box. The solution is it. But the cost of implementing the solution is quite high. What will increase the service life of your input door? If you want your entrance door to serve for a long time and looked presents all the time, then you need to protect it as much as possible from atmospheric precipitation and sunlight. The easiest way to the visor or canopy. This protection is not only for the door, but for you. In the rain you can safely open the door, not afraid of getting blocked, without fuss and hurry. But most often, even in the project of the house there is a porch. If the visor is more designed for 1-2 people, then a big family can fit on the porch. Lie need cold Tambour Or is it an excess? Why is it needed, because you can put the entrance door from the tree and this will be enough. And it is acceptable more for the southern regions. But if you discard the fact that with the door, we remove the excess load in the form of heat exchange and humidity, the following is obtained. The tambour makes it possible to save, excluding the through stream of air, along the simple draft. IN winterDue to the consistent opening of the doors, only a limited amount of cold air falls into the house. And also, in it you can leave street clothes and shoes, which is especially important in the offseason. Also there can be stored different tool or stroller and sled child. What are the minuses have entrance warmed doors from the massif? What do not do, and in burglar resistance the tree metal is not a competitor. Iron doors were created with this task, protect your home from thieves and hooligans. And how much is it critical in a private house where you can easily knock the glass? According to statistics, thieves try to do everything quietly. They will not break and make noise, they check the reliability of your locks. In general, it is better to entrust the guard of the house alarm than to believe on the bomb resistance of one door. Losing in burglar resistance, we have a lot wooden doors, as minimum 2 times less, Mass Iron. The tree is not only easier, but also the thermal conductivity coefficient of dry wood is only 0.15, and this 300 times less than from metal. Small thermal conductivity coefficient eliminates any waterproof points Each part of the door block. And at the same time you have many times more options for choosing design and painting your door. You completely create themselves appearance Your door. Solid appearance of the entrance door is excellent complement the style of your home, and at the same time will be harmonized with interroom doors. And all this will be made of natural material , "Live and warm" wood, and not "cold" metal. What is the cost of an inlet warmed door from a natural tree? By calling about 10 eminent iron doors manufacturers and learning from them the basic cost of the door with the thermal explosion, it came out that the inlet warmed door from the array comes out at least 2 times cheaper The cost of the iron door. See how your door can look, you can, looking

DIN 4400 4407 Replaced with DIN 18100, 18101 and 18102 standards, which are linked with DIN 4172. Nominal sizes door openings In the masonry installed by DIN 18100, shown in Table. 1. Based on these, dimensions are taken in the light corresponding to DIN 4172.

Table 1. Dimensions of doorways and doors on DIN 18100-18102:

Dimensions	Minimum opening widths (size in masonry)							The height of the openings from the pure floor mark to the bottom of the jumper
	Single-board doors				Two bipoly doors
	Cipher for door width							SIFR for the height of the door
	5	6	7	8	10	12	14	15	16	17	18
Nominal size of the face in the masonry	625	750	875	1000	1250	1500	1750	1875	2000	2125	2250
The size of the rumble in the light for brick walls	635	760	885	1010	1260	1510	1760	1880	2005	2130	2255
The size of the rumble in the light for monolithic walls	625	750	875	1000	1250	1500	1750	1875	2000	2125	2250
Free passage size with wooden boxes	575	700	825	950	1200	1450	1700	1850	1975	-	-
Free passage size with steel boxes	565	690	815	940	1190	1440	1690	1840	1970	-	-
Dimensions door box In quarters for all door installation systems	595	720	845	970	1220	1470	1720	1860	1985	-	-
The size of the door of the doors with a cry	610	735	860	985	1235	1485	1735	1860	1985	-	-
The size of the canvas doors without a pressure	590	715	840	965	1215	1465	1715	1850	1975	-	-

Shown in Fig. 1 numbers correspond to the width and height digits specified in Table. 1. They correspond to the number of modules in 125 mm, stacked accordingly in the size of the width and height. For example, CIFR 5x15 corresponds to (5 x 125) x (15 x 125), i.e. 625 x x 1875 mm.

The height of the doorway connecting the rooms with the floors on different levels, Determined by the room in which the door opens.

Dimensions door Towns They are accepted so that they can be hung as on wooden (Fig. 2 - 5) and on steel boxes (according to DIN 18111).

The dimensions of the door leaf with from the outlook are determined from the following conditions: The width is equal to the nominal width of the opening in the masonry minus 15 mm (2 x 7.5 mm); The height is equal to the nominal height of the opening in the masonry minus 15 mm (2 x 7.5 mm). Between the clean floor and the bottom of the door leaf cover 7.5 mm (Fig. 5).

The dimensions of the door leaf without applepose are determined by the size of the canvas with from the outlook minus the width of the floors: the width decreases by 20 mm (2 x 10 mm), the height is 10 mm. Door canvases with copamon better doors No applement. The thickness of the pressure is taken 24 (for the door cloths with a thickness of 36 mm) and 27 mm (for door cloths with a thickness of 39 mm).

Door hinges are installed: from above 250 mm below a quarter of the box; Below - 300 mm above the level of clean floor, Door handle Fasten at an altitude of 1050 mm from the pure floor mark.

DIN 18101 Sets the dimensions of the sections of the door items when ordinary ways their hits. The elements of the door structures should be made of din 4070 standard sections of the DIN 4070. From the boards with a thickness of 40 mm, planed elements with a thickness of 35 mm are made, and a thickness of 45 mm with a thickness of 40 mm (according to DIN 68706).

Sometimes apply doors with a threshold whose width is equal to the width of the door frame. Steel door boxes stamped from sheet steel (DIN 18111). One-piece steel boxes (Fig. 7) are used for partitions and walls with a thickness of 52, 75, 115, 175 and 240 mm. The size of steel angular boxes (Fig. 6 and 9) does not depend on the thickness of the wall, they can be used for the walls with a thickness of ≥ 240 mm usually together with a protective corner on another remove rib.

Steel boxes are attached to the slopes three anchors from strip steel on each side of the opening; The lower ends of the boxes are close to the floor to a depth of 30 mm and bind to each other band steel or corners. In fig. 6 shows the fitting of doors without a pressure, with shockproof rubber gasket, in fig. 7 - 9 - with from the outlook. Currently, asbestos-cement boxes are also manufactured.

1. DIN 18100 door opening dimensions (nominal sizes in masonry). 2. Door box and processing of the face in partitions. 3. Door box and processing of the workout in the walls.

4. Door box in the winds with a quarter. 5. Vertical cut of the door frame to fig. 3. 6. Corner steel box with shockproof rubber gasket. 7. One-piece steel box for doors with outlats. 8. One-piece steel box for partitions. 9. Corner box and protective corner (for thick walls).

Door boxes of thick boards and bars, as well as wooden liners should be closed by platbands, the size of which should take into account the thickness of the plaster. The wooden box knit in the spike, and the platbands in the Poltera and on the Us (Fig. 7).

Planed wooden boxes in partitions serve simultaneously beacons for plaster; They are installed before the partition device (Fig. 6) and protect the hill lump and the like by damage. It is necessary to ensure the possibility of light removal of the door with the loops (Fig. 10).

The doors in partitions are hung on steel boxes or on wooden boxes, fixed in the partition with strip steel anchors (Fig. 11). For outdoor doors, the use of plywood is undesirable, it is better to apply board doors, steel doors Or glazed steel doors. With the outer viper doors, the china must overlap with the strapping (Fig. 13). Balcony doors It is advisable to make a similar design with windows (Fig. 14).

Nowadays interior designequipped with a festival - the phenomenon is more rare than, say, ten or twenty years ago. This is due both to fashion trends that dictate the limit restraint in the design of blocks and with alternative methods of increasing the insulating properties of the product.

Fitting as a block element

As is known, for a more comfortable opening of the sash, as well as to avoid jams associated with the deformation of the product during the application, small technological gaps are provided between the box and the web. Despite the fact that the width of such gaps is minimal (2-3 mm), on the tightness of the block, they are capable of reflected negatively.

The advantage of the doors of Volkhovets with the entrance is that all the cracks are blocked by a special protrusion. It is selected in the canvas, and its thickness is equal to 1/4 of the sash thickness. For this reason, the item is often called a quarter, other consumable terms - Falts or inlet.

In addition to the described, there are several more varieties of the item:

Falk is made in the form of a plank, additionally superlacing on the cloth in such a way as to overlap part of the box.

Quarter is performed by S. inner boxes.

Features of the design equipped with a fold

By purchasing the door of Volkhovets with a fest, you will need to take into account a couple of nuances of its device.

A quarter is usually included in the product package, the loops of which are located on the side end of the canvas. Overhead canopies in this case are not possible.

The product looks more heavy, rather than an option not equipped with from the outlook.

As a rule, they are equipped with a doors of the doors of Volkhovets consisting of two sash. The protruding element overlaps the slot between the canvas, increasing the insulating characteristics of the block. In some cases, a quarter additionally complete the seal layer.

Scope of application

Doors Volkhovets with a preference preferred when the room requires increased protection against outsiders, cold air flows, moisture, dust, etc. According to buyers' reviews, the preliminary plank significantly enhances the tightness of the design. For example, such products are used in bathrooms, children's, bedrooms. Similar solutions are relevant in classical interiors.

More modern replacement folds are rubber, brushful or silicone sealantswhich are practically invisible to look, and therefore do not reflect on the design appearance.

With the help of our professional designers and masters, the door will turn into a work of art, will become an ornament and bright detail both exterior and interior.

Entrance doors Must be as comfortable as possible and easy to use and at the same time require a high degree of reliability and hack resistance. Multi-Log Castle from the German company G-U Series Secury AUTOMATIC, which is equipped with this series of doors, satisfies these requirements to fully - with its help the door automatically locks into three powerful bolts with simple door slam. Belcanto pressure headset, related to the class of protective fittings, and double-glazed windows with a safe glass that is applied protective film A3, which provides protection against vandals, unauthorized penetration and natural cataclysms.

Complete set of doors

The design is built on the basis of an energy efficient 5-chamber profile vEKA systems Softline with an enlarged assembly depth (70 mm), which has high indicators of thermo- and sound insulation. Five profile chambers provide not only increased insulating properties, but also durability: additional chambers perform the function of the internal rigs. Along the use of a closed reinforcing profile in the frame and the impost, it guarantees the constructions more high rigidity and geometric stability (flexural strength and twist).

Advantages of VEKA Softline 70:

• class A profile system (wall thickness 3 mm);
• 5-chamber profile with a mounting depth of 70 mm;
• provides elevated heat and noise insulation, gives finished design stiffness and strength;
• the deeper gabber pumping in Falts reduces the risk of condensate formation in the distance frame zone;
• closed reinforcement of frame and imposses for maximum geometric stability;
• rounded headquarters give the design of the window / doors elegant and unusual appearance.

On the glass applied a protective film A3, has a greater mechanical strength and increased security: Even if there is a blow to such a force that the glass breaks down, it will not split into sharp and dangerous fragments - there will be a strong protective film. This feature provides one more important advantage: If safe glass is broken or cracked as a result of mechanical impact, it can continue to perform a flexulating function until the glass package is replaced.

Advantages of impact-resistant glass chain:

• increased strength: glass with film is more resistant to mechanical loads, shocks and deformations;
• increased safety for a child: if the glass is still broken, the protective film will not allow him to operate on dangerous fragments;
• increased comfort: broken glass The film continues to perform a fencing function until the glass replacement.

Multi-speech lock Gu-Secury Automatic with a patented planetary mechanism of a special design makes the operation of the door to comfortable, light and safe. The monolithic rigleel and additional locking elements have inserts from hardened steel, which reliably protect them from sawing. The GU-Secury Automatic is equipped with two automatic falevas, which, after closing the door, are extended by 20 mm. They automatically lock the door and fixed, excluding the reverse move. Blossom resistance corresponds to the class A according to VDS classification (European Security Equipment Insurance Certification Center).

Features of the castle gu secury automatic:

• two automatic fault latches after closing the door are extended by 20 mm (automatically lock the door and fixed from the return movement);
• castles are checked in combination with different door systems RC 2 and RC 3 resistance classes;
• have VDS tolerance in class A;
• applicable in 1 or 2-fold door systems.

Purpose Handles of stainless steel Move smoothly, silently and with pleasant effort. The through threaded fastening with durable fasteners ensures reliable landing and prevents the fittings from the use of effort. From coarse pulling or turning a locking cylinder protects the lining. There is a spring-loaded mechanism for aligning the handle. The hardened elements of the external lining prevent drilling attempts.

Features and advantages:

• the protective cover of the cylinder is suitable for cylinders with a protrusion 12 - 19 mm;
• fixing rotation supports without supporting springs;
• arising axial traction efforts assumes the support with a large surface;
• radial efforts are transferred to a flexible and stable mount of the handle with a length of 8 mm using a toothed mounting element;
• additional recess for wDL lubrication.

The beautiful loop of the cylindrical roller type is distinguished by the lack of pads on the folding part - the fastening elements of the loops do not enter the front of the sash, and they are joined with the outflow of the sash and remain, so hidden. The visible part of the loop (cylindrical body) has a diameter of only 22 mm, so that in its class this loop is the most subtle and elegant solution from the market presented. Mounting the loop is performed without interrupting the seal. The maximum weight of the sash is 160 kg.

Benefits:

• all loops are tested for 1,000,000 opening / closing cycles;
• the housing of the loops is made of durable and light extruded aluminum (instead of a more common and fragile zinc alloy);
• loops are equipped with a powerful and durable stainless steel pin;
• "Self-admissive" bushings are made of the strongest composite, which includes Teflon, do not require care, cleaning and lubrication;
• the fastening of the loop occurs not in the fitting groove, but in the flood - it allows you to perform installation without cutting and pressing the seal.

The 5-pin cylinder system and Helius double-sided keys is optimal when the system with the same lock is required - convenient mechanical system "Master key", in which you can lock the front door, a spare door and garage gate with the same key. IN apartment house You can implement the "master key" system with various keys for each apartment.

Special convenience of operation ensures the proven single-row pin arrangement system and the use of bilateral keys. The cylinder is equipped with unlocking function with a key inserted on the other side, and an emergency function. A special key profile (patent until 2024) provides Helius cylinders high reliability and safety.

Features of the Helius double-sided key system:

• bumping protection (opening the castle by vibration from shocks, leading in motion of spring-loaded pins) due to the pins of a special form;
• profile cylinders with 5 pins;
• dispiration function with the key inserted on the other side (emergency);
• key material: high-quality nezilber - alloy copper, nickel and zinc (from it. Neusilber, literally - "New Silver");
• shlp screw: M5 x 80 mm, nickel plated steel (optional brass);
• the HS locking system has up to 15 individual locking, Z locking system - up to 40 individual locks;
• normal locking with key encoding;
• the key combined with the SE transponder (transceiver).

Designed to work with shutters up to 1400 mm wide and weighing up to 150 kg. The closer is distinguished by a miniature elegant case - device dimensions: height 63 mm, depth 44 mm and length 268 mm. With the help of infinitely customizable adjustment valves and control of the closing force, you can individually configure the comfortable functioning of the closers of the upper location. The entire closing force range is easily regulated by the 9th turns (en min. To EN Max.). Can be installed both on the internal and on outside. An attractive design provides an elegant lining of the sliding thrust and a durable closer cover used instead of a sliding lining. The cam mechanism "Double Heart" provides optimal functioning of the closing axis and a slight opening of the door.

Features of the closer:

• small size (D x in x g): 268 x 63 x 44 mm (along with a lid);
• maximum opening angle of 180 °;
  

  On the profile you can apply a lamination coating Renolit (Germany) with different pattern and texture ( different colors, wood breed, etc.).

  Installing the aluminum salary on the PVC profile gives the doors of a modern stylish and high-tech appearance, and also gives the design additional protection from mechanical, climatic and other impacts. The color scheme is represented by the full range of RAL colors, including various options "Metallic" -Od.

In the design of some door cloths, such an element is found as a follower, but what is it? In essence, the doorset is a certain continuation of the canvas, a small thickness plank, which comes on a small distance directly to. Let's figure it out for what purpose it is done and what the features of such models are concluded.

The entrepiece improves door characteristics

Differences of doors with a focus without

To begin with, allocate distinctive features Doors with a fest. Ordinary modern products have a straight canvas in stock, its edges are not weighted by any additional elementsWhen closed, it fully enters the box and small gaps remain between it and straps around the perimeter.

At the door with the entrance of the edge of the canvas, have an additional bar, which partially enters the box, and on top additionally pressed the protruding element. Thus, it is possible to achieve greater sealing of the structure, besides, the Pretake creates a very attractive decorative effect.

Such models are great for classic style Interior or Country, for modern design experiments it is better to limit the simple canvases.

In other words, such products refer to the "quarter" or "fold". The focus on standards has a thickness of one quarter from the thickness of the web, which served as such a name. As for the other term, it comes from the method of manufacturing such doors. During the calculation of the cutter, the mill cuts into the Falts canvas, this explains this name.

Pretake provides more dense door closing

Basically, such an supplement is attached to the doors from the wood array. It can also be found in some models of MDF Customs. Very often complement metal plastic structures And armored entrance doors.

The functions of the game and its advantages

What differ doors with the entrance now it became clear, but remains open question On the feasibility of installing such structures. Their cost is slightly higher than ordinary canvases, because additional manipulations are required. What is compensated more high price? Let's look at the advantages of the doors with the entrance:

• Soundproofing. Due to the more dense clips and eliminating side gaps, it is possible to create an additional obstacle to the penetration of noise and extraneous sounds.
• Heat insulation. The sealing of the joints prevents the passage of heat and cold in the opening, the drafts are eliminated, the presented temperature is maintained.
• Masks gaps. When installing the door, uneven gaps and skews between the web and the frame, which will reduce the aesthetic indicators of the structure, will be able to hide them at the expense of the action.
• Aesthetics. Product gives a special charm classic interior and serves as an additional decorative element.

But you should not be limited to stereotypes regarding style solutions, sometimes it is possible to organically enter such a design even in an ultra-modern interior.

The door with the entrance having many advantages will perfectly fit into any interior

Features of used accessories

In connection with the design features for such doors, it is necessary to choose a special fitness. First of all we are talking About loops. Since their axis is somewhat shifted outside the branch, the following models will be appropriate here:

• Corner cards - They have the form of the corners attached to the hinge element, are attached in the same way as simple straight loops: one part is fixed on the edge of the lutki, and the second screwed to the edge of the canvas and the inner part of the gunner.
• Orange - A good alternative to card loops, they consist of two screwed pins and a hinge, one piece is screwed directly to the box between the entrance and platbands, the second stud setting down on the canvas, nesting at the same time.

Output and corner card loops are well suitable for the door with the entrance.

Screw loops are suitable only for durable materialswho do not split at the same load.

If used, for doors with a follower, you should set special settings. It must be borne in mind that part of the canvas will touch the box outside, so the door movement should be more smooth at the end of the closing.

Doors with a festival - this perfect solution For home not only from a decorative point of view, but also in terms of useful functional.