Reading time ≈ 4 minutes
Long use of a plastic balcony door leads to the unbalancement of its mechanisms. As a result, the door is badly closed or stops closing at all. You can fix the situation by contacting the company that has been engaged in its installation. However, the specialist can not always go to you after the application, as a rule, you have to wait a few days. If time does not tolerate, you can perform work on your own. After all, the adjustment of the plastic door of the balcony does not cause great difficulties.
Adjusting the balcony door goes in several directions:
- vertically;
- horizontally;
- adjusting clamping.
Vertical adjustment
To eliminate the sagging that does not allow you to lean the door, leads to a hitch of the threshold when opening or closing, you need to adjust the sash in height, that is, move it up. Works are carried out from the bottom loop.
- First, free the loop itself from the cap.
- Insert a screwdriver in the hole in the upper end of the loop and turn the adjusting screw clockwise to lift the door. If it needs to be omitted, the rotation is made counterclockwise. Usually 2-3 revolutions are enough. You can see how to do it.
If such an adjustment of the plastic balcony doors is carried out independently, then after each stage it is necessary to check to make sure that everything is performed correctly. The sash must move freely, when opening should not have any problems, and when it is closed to enter without interference, but tight.
It should be remembered that not in all windows and the doors of PVC, the adjusting holes are made under the hexagon. Sometimes you need to use the key - an asterisk, as it looks, you can look at the photo. It is advisable to purchase such a key in advance, and if you need to adjust the plastic balcony doors with your own hands, it can be done with this device.
Horizontal adjustment
When fluctuations in temperature may arise deformations that do not allow closing the balcony door. The sash simply rests on the mechanism and does not go further. When using mechanical pressure on the door, it will be able to close. But the use of force when opening or closing the doors is undesirable, it provokes further deformation.
To eliminate this problem, a plastic balcony door is adjusted, namely her loops. For adjustment, you will need H4 hexagon.
- The end of the screwdriver is inserted into the side adjustment screw, access to which is available in the lower side surface of the bottom loop.
- The screw starts spinning to pull the leaf to the loop.
So the sash can be shifted to the right - left to a distance of up to 1 cm. If this is not enough, then you need to repeat all actions from the top loop. If the PVC balcony door adjustment is carried out correctly, the sash will be closed freely, without interference.
Adjusting the clabble door
So that the sash does not miss the cold air from the street, adjustment of the clips of the balcony door. To do this, use shut-off elements available on the sash. Usually they are made in the amount of 4 pieces. Almost always, the adjustment clamping screws are made as an eccentric, that is, a hole for the hexagon has some shift from the center and its rotation allows you to shift in both directions to obtain the optimal pressure level. Turning such an eccentric, you can either strengthen the clamp, or weaken it.
Sometimes the clamping screws have another design. If the screws go through a special opening, then at the central position, the presser will be minimal. Moving around the axis will lead to a change in the clamping level. Therefore, in order not to be mistaken with the method of adjusting the clamp, before starting work it is necessary on the website of the manufacturer's windows to familiarize yourself with the features of the fittings for the door that is installed with you.
To check whether the adjustment is performed correctly, you need to close the door, inserting a tight paper sheet under the top part or monetary bill. On the right level of clamping is indicated by the density of the clamping of the Covers, it should be kept in the place where it was closed, stretched out after the application of some effort. Using this simple reception, you should check the entire perimeter. If the paper holds everywhere well, it means that everything is done true, and winter winds, drafts are not terrible.
Adjusting plastic doors should be carried out about once a year. The timely correction of the position of the sash in the opening will help to avoid its irreversible deformation, will extend the life of the entire structure.
Video adjustment of plastic balcony door
The adjustment of the plastic balcony door is the process, during which various minor malfunctions can be eliminated, dying the operation of this system.
If you want to know how to spend the adjustment of the cloth of balcony doors with your own hands, then read the article.
More about the operation of double-glazed windows
Plastic windows and doors are an excellent alternative to traditional, wooden window and door structures.
They reliably block the street noise, protect the dwelling from drafts and fit well in any, both classic and ultra-modern interior.
The main minus such designs is the fact that they need frequent adjustment. During operation, the balcony windows may be loosened.
What to do when the balcony door is badly closed? Is it possible to eliminate this problem yourself, without attracting third-party specialists? Of course, yes.
How to understand that it is necessary to adjust the clamping the door made of plastic?
It is necessary to do that when it is necessary to make excessive efforts to open the door or then when the handle, the locking locking mechanism, does not cope with its work.
Timely adjustment, carried out in prophylactic purposes with your own hands, will protect the design of the glass package from serious breakdowns and significantly increase its life.
Spend a simple test that will make it clear that the design of the balcony doors needs to adjust the clips.
Swipe the door for ten to fifteen centimeters and watch it in motion. If the selected interval is preserved for a long time (in the absence of drafts), then you can not worry.
If the door is independently closed or, on the contrary, it is fully opened, you should take care of the adjustment of the presser mechanism.
Take into the hands of the construction level and with it. Measure the position of the niza and the top of the glass package relative to the floor.
If there is even a small skew, the door should be repaired by adjusting it to the jamb.
If you neglect by these works, you can achieve a significant skew of the design, which will lead to the appearance of drafts.
It is worth noting that the adjustment of the clashed of the balcony door can be carried out not only in the presence of certain problems arising during the long-term operation of this design, but also to improve comfort.
For example, in the summer, you can weaken the clamp of the design to create a natural ventilation of the room, and in the winter, on the contrary, to strengthen to ensure the absence of cracks and drafts.
Instructions for the operation of the glass packages contain information on how to make it with your own hands at home.
In addition, to learn how to adjust the position of the door on your own, using only fir-handed materials, you can, seeing several learning videos on the Internet.
How to adjust the balcony door of plastic?
To independently adjust the operation of the plastic balcony mechanism, use specific tools and materials.
You will need:
- screwdrivers of different sizes equipped with flat and cross profiles;
- passatia or pliers;
- keys with hexagon or star profiles;
- roulette;
- simple pencil or erasing marker;
- quality rolled strips made from PVC and equipped with a sticky layer.
In some cases, liquid plastic may also be needed for the repair of the balcony door, which freezes from contact with air.
You can adjust the position of the balcony door made of plastic, both front and horizontal and in vertical positions.
During the horizontal adjustment, the board of the gap is also produced, which is formed between the glazed glass package and the looper.
During the vertical adjustment, the height of the suspension relative to the door canvase is aligned. During the front adjustment, you can adjust the clamping glass.
Adjusting screws that are equipped with a door design are hidden under special decorative seals or panels.
You can remove them, picing the plane of a thin knife or a small screwdriver or unscrew using a small hex key.
The instruction manual for the plastic door design contains information regarding the adjustment of its operation.
If we use it, it is not possible to eliminate the existing problem, then you should not try to fix it with your own hands by anything.
Otherwise, you can damage the door cloth or disrupt the work of the design mechanism.
Reduce the need for frequent adjustment of plastic balcony doors such as microlifts and opening limiters can reduce.
They are able to evenly distribute the weight of the door canvase on all attachments and provide a smooth stroke when opening and closing.
Frequent problems of plastic doors and their solution
In this section, it is possible to familiarize themselves with the most common problems arising during the operation of plastic door structures, and learn how to eliminate them with your own hands for fast time.
If the balcony door opens poorly, it closes and clings during these processes behind the doorway from the latch of the mechanism, then you need to weaken or, on the contrary, increase the hinge tension.
To do this, turn the lower, medium and upper adjusting screws to one or two turns in the direction of the clockwise direction.
If the door saves and the threshold hits when it is closed, then the tension of the top and middle screw should be adjusted, and the lower tension is left unchanged.
To adjust the position of the screws, you should use a five-millimeter hex or star key.
To adjust the position of the connecting plane, you need to use similar keys with a diameter of two and a half millimeters.
To adjust the door clips, you should turn the eccentrics located on the back of the loops.
Please note that some door mechanisms are equipped with no eccentrics, but pin, turn, which can only use the passage.
The wrong position of the door leaf can cause problems reflected in opening and locking the door.
What to do when there are considerable effort to open the door? Adjustment work should be carried out, which was described above.
If the door is installed correctly and all adjusting screws are tightened, and the handle still turns with the effort, it should be replaced.
To strengthen the shackled handle of the balcony door, you should tighten the screws that are responsible for its mounting to the plastic design.
This can be done with a plastic screwdriver. Screws connecting the handle and the door are under a plastic overlay.
A deformed door seal made from polyvinyl chloride canvas can be replaced with a new one. Note: There are several species of these seals.
To understand their differences and buy exactly the one that needs, you should come to the store either with a sample of the seal, or with a technical passport issued by the door design installer.
You can remove the deformed seal with your own hands using a flat profile screwdriver.
The groove in which the seal was located, should be cleaned from the remnants of glue and sera, degrease and pour a new layer of glue or liquid plastic into it.
After the glue is "grabbing", you should attach a new layer of insulation and wait for the complete hitch of this design.
Adjusting plastic balcony doors - a simple process to cope with which you can independently.
To reinforce confidence in the success of the door design adjustment, you should see several thematic videos on the Internet and it is mandatory to familiarize yourself with the instruction manual for the plastic product.
Many plastic owners come from time to time to such a problem: how to adjust the balcony plastic door. In this case, the design may be loosely closed, the handle or loop is cleaned. The process of regulating the door device is not distinguished by complexity. You can twist and fix accessories in a few minutes.
Practically and conveniently issuing out the balcony will help plastic structures
Read in the article
Features of the design of the balcony door
PVC products are a suitable option for. Such structures are characterized by resistance to temperature jumps and influence. Such products have a small weight and do not become encumbrance for exposure to moisture and temperature drops. When creating plastic doors, the same profile is used as when installed.
Plastic products have certain advantages:
- thanks to the multi-chamber profile, it is superbly maintained and distinguished by good;
- differ immunity to any manifestations of the external environment;
- possess environmental and durability;
- characterized by unpretentious care.
Most often for balcony structures use glass top and plastic bottom. If there is a solid frame, the door is performed using triple glazing. This allows you to create a stained steel construction and increase natural.
The following design options are popular:
- sliding models that are moving using the groove system. When they are installed, it is required to observe tightness. Also, the installation is carried out on;
- With one and two sash, which is equipped with a hinge lock fitting. This requires adjustment of hinges;
- double designs with an impost. In this model, the sash opens, but insertion is placed between them - an impost;
- the shill version consists of two parts. At the same time, one is fixed in one place.
Great value has accessories. It allows you to make clamp more dense. The accessories are divided into inner and external. Internal elements are no different from. Inner includes door swivel handles, balcony latches, decorative linings and stationary handles.
Helpful information! The most important stage is the installation of the door frame. It is installed with the exact definition of vertical and horizontal directions. Then the design is fixed using selflessness and anchor bolts.
How to adjust the balcony plastic door: ways
Most balcony owners are concerned about the question: how to adjust the balcony plastic door. You can make the device setting on your own, which allows:
- apply regulators for removing wires of cavities;
- remove shifts in any direction;
- perform clamping clips;
- place a plate for the ventilation regulator under the handle;
- perform lubrication of all moving parts.
As a lubricant, a special oil composition is used, and a brush or cotton wand will be needed.
The table shows some doors setup techniques:
| Picture | Ways adjustment |
 | Loop adjustment. |
 | Setting the position of the assignment. |
 | Methods for adjusting using a hex key |
 | Adjusting pressure. |
 | Features of the adjustment of the end of the balcony block |
 | Adjusting the clips. |
 | The diagram of adjusting the upper and lower loop. |
Article on the topic:
With this task really cope without contacting the specialist. All you need to know about the peculiarities of regulating these structures, we collected in this material.
The main problems of plastic doors
If the balcony plastic door is not closed tightly, it is easily adjusted. You can encounter certain problems:
- the bottom of the panels when opening the plastic threshold. This arises due to the sedimentation of the structure, which is manifested in the summer with a frequent opening of the sash, as well as with a heavy double-blade;
- in the middle part of the blade, the flap hurts the element of the frame, due to temperature jumps and drafts;
- the canvas is not sufficiently adjacent to the frame, and cold air stretches from under the sealing material. This happens with insufficient fit to the frame;
- if you often open and close the sash, the handle begins to stick. At the same time, manipulations are done so that the handle stops fuddling in the nest.
Adjusting the climbing of the balcony plastic door is produced by a hex key. For work it will take flat and sacral screwdriver, roulettes and plastic strips.
Before setting up the design it is necessary to decide on the type of problem. Most often, there are difficulties in opening and closing of the canvas, at skews, when blowing and moving the handles. If the cloth falls down or the door is hardly closed, it is adjusted for a separate fittings, or a complete setting of all mechanisms is performed.
To find out whether a piece of paper needs to be repaired. It is put on the frame and closed the door. In those places where the leaflet without problems is pulled out the canvas not tightly pressed to the box. To detect the breakdown, the canvas should be circled in a closed state, and then the sash opens and the lines are cooked with the frame.
How to perform adjustment of plastic balcony doors yourself: video
It is easy to carry out the adjustment of plastic balcony doors on your own, special instructions will help.
Features adjusting the knob
The following problems occur with often:
- the handle turns not to the end or goes tight. If the setting does not help, then it is necessary to replace;
- if the handle is breaking, the pad is rotated at the base of the handle by 90 degrees and the two screws are tightened, which are hidden behind it. For this, the cross screwdriver is applied.
Replacing the seal
If there is a breakdown in the door, then it is often deformed. In such a case, it is with the same cross section configuration. Old material is removed from the groove with a screwdriver. Then the surface of the groove is brushed from particles of glue and dirt. When installing a new seal, you need to control so that it is tightened. Before laying the grooves is labeled with glue. This needs to be done in areas where the ends of the sealant will be placed.
Helpful information! For high-quality work, it can be equipped with a opening limiter and microlift, which prevents situations. The limiter does not allow loaves.
What to do when sagging?
Many people are interested in how to adjust the balcony plastic doors during sedimentation. To repair the repair, it is necessary to restore the cloth higher and move to the loop at the top. Then a certain sequence of actions is performed:
- the sash opens in a reversal position;
- with the application of the hex key, the screw rotates next to the loop. Then there are several turns on the right side;
- to get to the screw element, you need to remove the decorative caps;
- the screw turns clockwise and the door design is raised;
- checked freedom.
Helpful information! Furniture systems can be approached not only under the hexagon, but also turn a closet.
Setting with the middle side
If the balcony plastic door is poorly closed, then adjust the adjustment that can be seen on the video. When clinging the site of the canvas in the middle, the movement of the sash is closer to the hinges:
- the sash is allocated to the bottom loop, and then the key is inserted into the side screw and tightly pulls into the loop direction;
- then the same manipulations are carried out for the upper loop.
How to make custom adjustment?
Such work is made using shut-off products in the form of eccentrics. They need to move the pliers. So that the setup is more efficient, you need to explore the instructions represented by the manufacturer.
The setting is made several times a year. In the summer, the clash must be relaxing, and - more dense. At the same time you need to know how to adjust the balcony plastic doors for the winter.
Adjustment is as follows:
- decorative cap is removed;
- at the bottom of the carport there is a screw, with which the clamp of the clamp is changing;
- to change the clamp at the top, you need to adjust the screw itself;
- the sash swallows and holds the block driver;
- the hexagon is installed in eccentric and turns on the desired side;
- then the blocker is pressed to the seal, and the sash is placed in place;
- eccentrics are installed in place where the maximum clamp is performed. At the same time, the mounting bolt is slightly released, and then shifts to the desired position.
Useful advice! For better design work, it is recommended to use machine oil to lubricating accessories.
Features adjustment with conventional fittings
It is very easy to solve: how to set up a plastic balcony door if the fittings are standard.
To adjust the door, it is required:
- remove decorative parts with sheds;
- using a hex key, unscrewing the screw on the reverse side;
- then a manipulation with a long horizontal screw is made. For example, that the sash does not cling to the upper part of the frame, you need to lower the upper screws and go down the cloth;
- several turns are made to check the design.
Article
If from the side of the balcony blows, or the door opens, closes badly, the problem is absolutely not necessarily as a door or unfair installation. Often the situation can be corrected by adjustment. How is the adjustment of the balcony plastic door?
If the warranty period has not yet come out, you can call the masters from your installer. Moreover, the installers were required to adjust the door at the end of the installation. But someday the warranty will end, and you still have to regulate the door yourself, if you do not want to spend your extra money. Doors are increasing much faster than the windows: they have more weight, they are open-closed more often.
Important: New houses during the first year give shrinkage. During this period, you need to follow the door. In the running version, the design may be deformed.
Qualitatively installed and adjusted door:
Tightly and evenly pressed all over the perimeter;
There are no visible distilts and deviations from the vertical;
Resistant in the open position (in the absence of wind).
Video "Adjustment of plastic balcony doors":
Condition status is checked using a paper sheet. The sheet is placed between the sash and the frame, lock the door, pull out the paper. It should be removed with some effort.
It is possible to identify the irregularities of the installation (the web is poorly combined with the frame) with a simple pencil. You need to circle a locked door around the perimeter, open and see how much the line is parallel to the edge of the frame.
The adjustment of the plastic balcony door is also necessary if: the handle is poorly rotated, the seal is unevenly deformed. If he was deformed below, the door must be raised by adjusting the bottom loop, if at the top - to lower a little, adjusting the upper one.
Instruction
Required tool kit:
Keys and hexagons of different sizes;
Pliers;
Screwdrivers, slotted and cross;
Roulette.
There are three hinges on the door, in which there are adjusting screws. The adjustment of the plastic balcony door is made as follows:
1. Open the door, unscrew screws, fixing decorative lining, hexagon 3.
2. Close the door, remove the lining.
3. Under the lining there is a screw, located horizontally. With it, the door is adjusted horizontally. To raise the lower corner of the sash, you need to tighten the screws in two hinges, top and medium.
4. If there is a need to shift the canvas to the right / left completely, you need adjusting horizontal screws of all three loops.
5. To adjust the plastic balcony vertical vertical (lift / lower), screws are used in the lower parts of the loops and the hex key 5.2. The door is lowered by rotating the screw clockwise. In the opposite direction - rises.
6. Move the lower angle to the right / left can be tightening the same screw on the bottom loop.
7. To adjust the upper or lower response, use the hexagon 2.5.
8. The shut-off bar can be tightened with a cross screwdriver.
9. For adjustment of the clips, a special axle axle is used on the accessories. It is turning the passage. To reduce the clamp, the pin is rotated into the parallel with the profile (this is the extreme position) to zoom in - across.
10. In other models, there are no axles, the adjustment of the plastic balcony door is performed on the retaliatory bar. In this case, you need to insert the hex key on the bar on the bar and make something about half the turn.
Change the old wooden balcony blocks to new plastic now try almost everything. After all, such structures are more attractive externally, they do not lose this quality over time, it is better to protect the room from the penetration of cold or, on the contrary, hot air from the outside. However, even the most expensive PVC structures have an unpleasant feature: with some periodicity they need to configure and adjust the clamp. Let's find out yourself, without contacting the specialists.
When is the adjustment of plastic balcony doors?
The adjustment of plastic doors to the balcony is made if the following violations in the operation of the mechanism are noticed:
- it is necessary to apply efforts to open;
- closing the doors on the balcony, you can feel like a cannut it clings to the door frame;
- the lock handle or she, on the contrary, is too tightly rotated;
- if the lock is open, the door spires spontaneously;
- from under the closed doors blows.
Detection of these symptoms indicates a launched state of the plastic design and the need for adjustment. It is possible that simple adjustment will not help, repair or replacing some details, which entails excess costs. To avoid such a situation, we recommend the doors on the balcony regularly and timely configure. You can identify violations in several simple ways.
Methods for identifying the need to adjust plastic structures
Check whether the door design needs to be adjusted, you can use simple actions.
- Do not completely close the door leaf. If it is not held in the initial state, but it begins to open / close it in itself, it is time to engage in adjustment.
- Become with the opposite direction from the direction of opening the side. With a simple styling pencil, circle the edge of the door. Now open the balcony, look at your "Drawing", if the lines you draw parallel to the edges of the door box, is not worried about what. Otherwise it's time to get tools.
- Clean the balcony door with a notebook or newspaper sheet, try to extract it. How much effort did you have to attach? Repeat similar manipulation follows in different places. With the climb, everything is fine and the adjustment is not needed if the same effort was attached to pull the sheet.
How to regulate plastic balcony doors?
Before you start adjusting the balcony doors with your own hands, make sure that you have the following tool:
- different screwdriver, flat and cross-shaped;
- pliers;
- keys with different profiles;
- yardstick;
- plastic gaskets with self-adhesive layer;
- easy marker or simple pencil.
In some cases, it may take the presence of liquid plastic frozen when contacting air.
Plastic door adjustment directions
This process is carried out in several directions:
- frontally;
- horizontally;
- vertically.
We propose to consider each of them more.
Horizontal adjustment
Temperature fluctuations can cause deformations due to which difficulties arise with the closure of doors, they begin to rest in the mechanism. You can closure, only attaching considerable efforts. However, these actions are undesirable, thereby you provoke further deformation.
To adjust, you will need to pull the door loops. This is done with the H4 hexagon.
- Insert the tip of the screwdriver to the adjustable screw, located on the side. Access to it is placed on the bottom side plane of the door loop.
- Take the leaf to the loop, twisting the screw.
Thus, you will succeed in achieving the shift of the sash 1 cm to the right or left. In case of need, this adjustment is made from the upper loop. After that, closing problems should disappear.
Vertical adjustment
The sagging does not allow you to open the door to ventilation, it starts to touch the threshold when opening and closing. Correct the situation can be adjusted with a loop in height. Actions are performed from the loop located below:
- Remove the protective cap from the loop.
- Insert the screwdriver into the hole located in the upper end, repent the screw clockwise. If the door, on the contrary, needs to be lowered, the action is performed counterclockwise. Almost always 2-3 revolutions are enough.
Not in all PVC designs of the holes are made in the form of hexagons, you may have to use the clock key.
Frontal setting
The adjustment mechanism depends on the product modification:
- With the opposite side of the side loop on the door of the door can be arranged eccentrics, they must be rotated using fir-handed tools.
- A number of models has an Assuple on the accessories. It is rotated by pliers. Maximum clamp can be achieved if you give it a direction perpendicular to the door block.
- In some cases, it is necessary to shift the retaliatory bar. To perform this action, use the screw-hex under the bar.
- Carefully cleaning the surface of the accessories, following its condition, you will increase the operational resource of the entire PVC design.
- If when you close the rotation, the handle does not reach the end, clean, lubricate and adjust the accessories.
- Opening limiters, microlifs will help reduce adjustment frequency.
Learn some additional nuances of the process of adjusting plastic doors, you can see the video below.