Coffee table cannot be called essential furniture, but it occupies an important place in the arrangement of a living room or bedroom. Modern tables are endowed with a lot of functions, representing a storage system not only for the press, but also for other useful things. Many models are equipped with spacious drawers and compartments, a transforming system, turning into an oversized dinner table. Among other things, the coffee table acts as a significant decorative element that successfully complements stylish design. It’s quite possible to make such a thing with your own hands if you apply some imagination and patience, and our article will provide interesting ideas for designing a coffee table at home.
Materials for production
Many different materials are used in the manufacture of modern coffee tables. Unlike previous times, when standard rectangular structures were stamped from MDF, today's models surprise with their diversity. One of the expensive options are wooden tables made of natural massif. Such a thing will decorate any interior and will always look chic and respectable. The designs come in a wide variety - from strict, rough tables to Scandinavian style to classic ones, decorated with forging or carved decorations.
Since wood is quite expensive, chipboard and MDF boards can help replace it. If we talk about durability, they are, of course, inferior to wooden ones, but they look no worse. Design tricks allow you to compensate for the simplicity of the material, for example, transformable tabletops, built-in sockets, etc.
Metal also takes part in the design of coffee tables. From metal pipes form frames, then supplementing them with countertops made of other materials. The graceful curls of forged elements with glass tabletops look very beautiful. Sometimes you can find designer designs in which the table consists entirely of metal.
In modern furniture production More and more often you can find glass interior items that bring a certain lightness and airiness to the atmosphere. Products are made of heavy-duty tempered glass, resistant to various kinds influences, so you don’t have to be afraid that such a piece of furniture will break or become deformed under the influence of high temperatures. In some models, only the surface of the tabletop is covered with glass.
Plastic is used much less often, as it does not differ high strength, but has a large color palette and low cost. Most often it is found as components of a wooden or metal structure.
IN homemade For original coffee tables, the choice of material increases significantly, since, in addition to traditional materials, various improvised means are used.
How to make a coffee table: beautiful ideas
To make coffee tables with your own hands, plywood is most often used, which is relatively inexpensive and easy to process. You can also use various available materials and build the most bizarre designs. More complex parts, such as curly handles, legs, wheels, fittings and other decorative elements, can be purchased at a furniture store.
Modern style plywood coffee table
Making such an original coffee table will not require much time, but the product will take its rightful place in any interior with a touch of minimalism. To work, you need to purchase a sheet of plywood, three legs with fasteners, thick thread, a pencil, a tape measure, a jigsaw and paint (preferably white or black).
So, the first thing you need to do is cut out the tabletop. On the back side of the sheet, select a point that will be the center and drive in a small nail. Cut a piece of thread the length of the radius of the future table. We attach one end of it to a hammered nail, and tie a pencil to the other and, pulling the structure, draw round shape countertops. Next, you can dream up and give the canvas more original form. It is noteworthy that to make such a table you do not need drawings and measurements at all. We cut out the drawn shape of the tabletop using a jigsaw, sand it and paint it. When the structure is completely dry, we attach the legs. The table is ready.
Coffee table made from pallets
This original design fits perfectly into many styles. It will most successfully complement a daring loft or natural eco-style. Design one exclusive table not difficult: for work you need to get a pallet, metal legs or wheels (at your discretion). You also cannot do without screws and a screwdriver, a saw, paint or varnish with a brush.
Step by step, all work on constructing the table will take place in the following order:
1. Mark the dimensions of the table on the pallet and saw off the excess part.
2. We take planks from the leftovers and cover the gaps in the main structure with them to create a continuous surface, fixing them with self-tapping screws.
3. We turn over and form five transverse strips: two on the sides (the legs will be attached to them) and one in the center for stability.
4. We mount the supports and open the structure with varnish or paint.
Tire coffee table
An old worn-out tire can be a great base for creating a beautiful home coffee table. Additionally, you need to prepare the plywood. Before you begin construction, you must thoroughly wash and dry the tire. Next, you need to measure the diameter of the tire and cut two circles from plywood: one - the tabletop - should correspond to the diameter of the tire, and the other - the base - should be a few centimeters smaller. You can immediately attach legs, wheels to the base, or leave it without supports at your discretion. We attach round sheets of plywood to the tire using self-tapping screws or sit them on construction glue - the base is ready.
Next, we choose one of two methods: we wrap the rope either completely around the structure, or only at the sides. In the first option, you need to think about how to treat the countertop - perhaps paint it or coat it with a shiny varnish.
You should start wrapping from the center: fix the end of the rope with a self-tapping screw or a glue gun and begin the movement of winding circles, gradually moving to the sides. There is no point in wrapping the base, unless you decide to make the table half two-color. At the end of the winding, the entire structure should be coated with transparent varnish to extend its service life.
Coffee table made from drawers
If you have any lying around on your farm wooden boxes from under vegetables - do not rush to throw them away. Just four of these containers can turn into a beautiful and useful part of your living room interior. If you don’t have drawers, the hardest part of making a table will be getting them. Then everything is simple: the boxes need to be sanded, painted and folded, as shown in the photo. We use a sheet of plywood, which must be screwed to the bottom side of the structure so that it does not fall apart. So our coffee table is ready. The advantage of this design will be the organization of spacious storage areas for various magazines, books and other things.
Coffee table for travel lovers
Nowadays, traveling around different countries became available to many. But there is a special category of people who simply cannot live without constant travel to remote corners. They are the ones who will surely like a coffee table reminiscent of certain pleasant voyages. Any one is suitable for making old suitcase with rigid walls, not suitable for use direct purpose. You will also need a sheet of thick plywood, a screwdriver with screws, paint and, if desired, legs or wheels.
We cut out two sheets of plywood with an area equal to the base of the suitcase, attach them with inside to the base and lid. Screw on the legs or wheels. Next you need to decorate the table - for this they use different ways. One simple option is to paint it in White color, and when the structure is dry, use sandpaper to make abrasions indicating the antiquity of the item. This product will suitably decorate a living room in a shabby chic style. The black color of such a table will harmoniously fit into a loft living room, and the decoration using the decoupage technique will become a real masterpiece of Provencal design.
Coffee table made of driftwood
The uniqueness of furniture made from stumps and driftwood lies in its uniqueness - what is created by nature itself does not have similar patterns and textures. Such products always attract the eye with their curves and weaves. In addition, get raw material not so difficult - it can be found in the forest, on the shore of a pond. The snag needs to be washed, cleared of bark, and rotten waste removed. Next, you need to adjust, align the shape under the table top and base and let the workpiece dry thoroughly (if there is any large holes, it can be puttied).
The dried driftwood is carefully sanded, covered with stain (you can choose the shade you like best) and varnish. The base is ready. The table top can be attached using construction adhesive or self-tapping screws (depending on what it is made of). Nowadays, glass tabletops are very popular, through which winding wooden branches are clearly visible.
DIY coffee tables – photo ideas
We looked at only a few options for making coffee tables with our own hands. Much more information and photos finished products our gallery will provide you with a lot of information interesting ideas. Enjoy watching!
Choosing a coffee table. Advantages and disadvantages of each material. Which table should you choose for your interior? Do you need shelves and drawers on a coffee table? Photo ideas for inspiration: transforming table. We make a coffee table with our own hands.
Choice of material, pros and cons
A coffee table is considered the most functional and versatile piece of furniture in any interior. It is present in almost every living room. It can often be found in. The coffee table will even fit on yours if you like to sit there while reading or working on the computer. With its help, the space will become more comfortable and aesthetically beautiful. We will tell you what types of coffee tables are divided into, what materials exist for their manufacture, as well as the pros and cons of each.
| Classification: | Classification characteristics: |
|---|---|
According to the form; By height; According to the material from which the frame is made; According to the material from which the countertop is made; Depending on the method of movement; Depending on the presence of a folding mechanism. | Circle, oval, square, rectangle, triangle, polygon, arbitrary (unusual) tabletop shape; The average height of a regular coffee table does not exceed 50 cm (however, there are models of lower and higher tables); Wood (driftwood, stump), glass, metal ( Forged Products), plastic; Wood, chipboard (laminated), wicker, fabric or leather upholstery, tempered glass(including tinted), plastic, veneer, metal sheets, mirror surface, stone, mosaic; On wheels (mobile) and without (stationary); Transformable or regular tables. |
A coffee table is considered the most functional and versatile piece of furniture in any interior. It is present in almost every living room. It can often be found in a spacious bedroom.
Made of wood
Wooden coffee tables are the most popular option and can easily fit into almost any interior. It is enough to choose a shade that will harmoniously combine with the rest of the furniture in the room. It is desirable that the decoration of such a table be made in the appropriate style.
From glass
When decorating their home in a modern style, people began to more often pay attention to models of coffee tables made of glass. They look quite “airy” due to their transparency. However, the most unusual materials can be selected as support for such tables - tree snags, deer antlers, corals and others.
Made of metal
Metal is difficult to process, which is why models of such coffee tables are expensive. They are also heavy in weight, which makes moving them around the room much more difficult. But they are durable, they are not afraid of any damage.
Choosing a coffee table depending on the overall style of the room
Look at examples of interior design, including the presence of a coffee table, in the catalog - you can see how diverse they can be (in shape, materials, decorative elements and purpose):
When choosing a coffee table for the living room, clearly think about what “responsibilities” you assign to it.
Classical
The most ordinary small coffee table made of wood will fit best into a classic interior. The only exceptions can be bright decor base and legs of the table, matched to all other pieces of furniture and decoration. It is very important in such situations to take into account a careful selection of wood tones so that the furniture looks like a single set.
Provence
A feature of the Provencal style is considered to be pastel shades of furniture, including naturalness (unpainted wood); carved table legs and antique design (artificial aging) are no less popular. For example, in the living room large area Massive coffee tables will fit better. But for a small room, small models are ideal. If you prefer french style, then these tables are for you:
Country
Most ethnic styles (by the way, which includes country) are amazing original ideas And unusual use the most common materials. Some surprise with models made of bamboo, others with multi-colored complex mosaics laid out from small shells. Country is able to accept into its interior a table made of rough-hewn wood or logs. Also in appearance, models of this style are represented by the roughness of the surface of unpolished wood. See for yourself:
Modern
Where there really is no end to designer imagination is in the modern style. Fortunately, materials for making such coffee tables can be found everywhere - wood, stone, glass, metal, plastic. The most important thing is to keep the shapes and lines laconic. A little creative approach and a unique coffee table will appear in your interior.
Pop Art
The main goal of the pop art style is to transform ordinary things into something out of the realm of fantasy. By creating such “works of art,” this style allows you to transform drab everyday life with bright decorative elements. Coffee tables were no exception here. Designers spare no inspiration, improving existing simple things.
Loft
The presence of rough metal parts and roughly processed wood, as well as the creation of a unique look of “street furniture” - this is all loft style. He is original and brutal. At the same time, everyone without exception likes it. If you see a coffee table that resembles a cart, know that this is also a loft. Many ideas came to the designers’ minds when they visited “specific” places - semi-abandoned old factories and manufactories, where they drew their inspiration.
Transformable coffee table
When choosing a coffee table for, clearly think about what “responsibilities” you assign to it. If you need decorative element interior, then take a closer look at the unusually shaped tables that are often offered by various designers. However, if you want to get not only a coffee table, but also a dining or computer table all in one, then you should look at folding models -. With a little effort in just one minute, you can turn your tatty coffee table into a full-fledged one. dining area for several people. Isn't this what you dreamed about?! It would be great if such a model is on wheels - this will make it easier to move the table around the room.
DIY transforming table:
Coffee table as an element of a storage system
Its very name – “magazine” – suggests that this table is intended for storing magazines, as well as books, newspapers and other small items (remotes remote control, phone chargers and the like). In order not to clutter its surface, most models have shelves or drawers that create additional space for storing necessary things. Such elements of the storage system will not necessarily be located outside - in plain sight, they can also be built-in (hidden, secret), which only you will know about. Here are just a few models with original ideas:
DIY coffee table - video and drawings
| Materials and tools: | Progress: |
|---|---|
Prefabricated parts made of fiberboard or wood. 2 wheels. Special glue for wood. Drill and drill bits for it. Electric screwdriver, screwdrivers. Jigsaw, wood saw. Screws and tongues. Roulette and level. Sandpaper or sanding machine. Wooden hammer. | We cut out the parts according to the drawing. We make holes for the tongues in the rectangular partition and in the center of the base of the tabletop, at an approximate distance of 10 cm. Now, at a height of 36 and 48 cm, we make 2 holes on the partition itself for the subsequent fastening of 2 semicircular shelves on it. Dowels can be installed. We assemble the table, first making sure that the overall structure is even. We disassemble it again and make several holes in the rectangular blanks (36, 48, 23 cm). Let's get started final assembly. To do this, we sequentially assemble the base, central and lower partition, semicircular shelves, an upper partition and the tabletop itself. We collect using wooden hammer and tongues placed on glue. We complete the assembly process by attaching the wheels to the screws (when the table moves further, they should not touch the base). That's it - the table is ready! |
We invite you to watch several videos from striking examples original models of coffee tables that can be made without leaving home.
Even a novice craftsman can make a table from scrap materials. But before assembling a coffee table with your own hands, it is better to review the drawings and diagrams in advance. This will allow you to decide on the shape of future furniture and cut off too complex options.
DIY drawings and diagrams of coffee tables
It is comfortable, lightweight and versatile. To make the frame rigid, the underframe is assembled from legs and a drawer - a rectangle that connects the legs and supports the tabletop. Otherwise, the legs will move apart and the table will lose its stability.
At the same time, the complexity of assembly does not increase much, but now you can store books, notebooks or other trinkets in the coffee table.
A special feature of this design is the absence of legs - they are replaced by four sidewalls, to which a ready-made one is attached from the inside. folding mechanism. It is fixed to it on a short pair of supports wide board- an underframe, and a double tabletop is attached to high supports, which, when unfolded, rests on the underframe.
Magazine table made of PVC pipes
The simplest and most economical, but very original version coffee table - make it from plastic pipes. The shape and height depend only on your wild imagination. It might be small round table, serving as a bedside table or a full-fledged coffee table with a glass top.
To create it you will need:
- pipes of two diameters - thicker for the legs and narrower for the base, for example, 16 and 9 mm;
- glue gun or tube of transparent superglue;
- medium grit sandpaper;
- a hacksaw for cutting plastic pipes (can be replaced with a wood saw);
- acrylic paint to hide the printed markings on the pipes.
The process itself is incredibly simple:
- Cylinders are cut to the selected length. 4 legs are made from a thick pipe - their length will be equal to the height of the future table (40-50 cm). 30 short cylinders are cut from a narrow pipe, on average 10-15 cm (depending on the shape of the table, the number can be changed).
- You need to start assembling the base from the center - this way there will definitely not be large gaps between the cylinders. Glue is applied to the entire surface of the contacting pipes. A little trick - to accurately glue the cylinders, liquid superglue is poured from the end of the pipes so that it flows down along the entire length of the joint. Glue gun the joints are simply processed from the outside - after painting they will become invisible.
- When the desired shape is achieved, the legs are glued - you need to make sure that the diagonal distance between them is equal. Otherwise, the table will fall over on one side.
- The final stage is painting. The easiest way to do this is with an aerosol method, although you can also use a simple paint brush.
When placing a glass tabletop on your table, you should choose tempered glass with a thickness of 10 mm. To prevent the removable tabletop from sliding on the base, use silicone shock absorbers for furniture.
If a permanent tabletop is planned, it is fixed with transparent silicone glue.
DIY wooden coffee table assembly
For fans classic style there is nothing better than a wooden table. For this you will need to stock up:
- planed timber 40x40 mm - for legs;
- planed board 50x20 mm - for the drawer;
- a finished tabletop made of furniture board 800x400 mm (but MDF or plywood is also suitable);
- use wood putty to fill the holes from the screws;
- sandpaper or use a sanding attachment on a drill to process wood;
- varnish or paint - for finishing table
The tools you will need are a screwdriver (or screwdriver), a wood saw and a drill. After cutting the block into legs, and the boards into the frame, the assembly of the table itself begins:
- The underframe is assembled first. For convenience and ease of assembly, everything is done upside down. The sides are attached to the legs obliquely with self-tapping screws through preliminarily drilled holes. But it is also possible metal corners, if aesthetics are not so important.
Wooden tables are made not only from planed wood. If you have minimal woodworking skills, you can create original furniture even from firewood. For example, by selecting a wooden block of suitable height and a couple of Y-shaped thick branches, working a little with a sanding attachment and covering everything with varnish, you will get an excellent massive coffee table for the garden.
And if after building a house there are several euro pallets left, there is no need to rush to dispose of them. This is an almost finished table!
It is enough to sand and stain the surface, place them one on top of the other and securely connect them together. And to make the table mobile, 4 wheels are screwed onto the bottom, 2 of which have brakes.
Decorating a coffee table with epoxy resin
If there is a sawmill nearby and you can get a sawn board with a lot of defects for next to nothing, that’s just great! It is from such materials that the most beautiful tables, decorated with epoxy resin.
The process is labor-intensive, but not too complicated:
- The cut board is glued with wood glue into the tabletop. Smooth boards must be placed under the clamps for uniform fixation.
- After the glue has completely dried, the tabletop is sanded, all cracks and holes from knots are cleaned. Before application epoxy resin the surface must be cleaned of dust and small chips.
- To make the table glow effectively, use luminescent paint in powder. For 2 liters of ready-made resin solution you need about 100 g of paint. The resin and hardener are mixed 1:1, the dose should be measured accurately and so that the hand does not tremble. If you overdo it with the hardener, the resin will crack, while too little hardener will prolong the hardening period.
This tabletop is suitable for both a coffee table in the living room of a cottage and in the bedroom of a city apartment.
If you have a few meters of wooden blocks left at home, you can even make a table out of them! The video shows in detail and clearly how to make unusual designer furniture from construction remains:
Making furniture with your own hands is not only a great way to save money, but also an opportunity to put your creative potential into practice!
We will talk about making coffee tables with your own hands. There is no such thing as too many side tables. They can be placed next to the sofa to place a vase of flowers or a mug of tea, used as a bedside table or as a stand for potted indoor plants. However, monotonous wooden tables are unlikely to liven up a dull interior. I want something stylish and unexpected...
Stylish table made of wooden slats with your own hands
This bench can serve as a coffee table, extra seating, or a place to place indoor plants. This piece of furniture will “fit” well into almost any interior!
DIY coffee table photo
Materials:
Tools:
Step one: Using a hacksaw, cut the ends of two 2.5 x 7.5 cm boards at a 45 degree angle. Cut out fragments from 2.5x5 cm bars, the length of which will correspond to the internal length of 2.5x7.5 cm blanks.
how to make a coffee table with your own hands. Photo
Step two: Place 2.5x5 cm of the workpiece in the middle, and 2.5x7.5 cm on the edges. Make sure the ends of the inner slats are aligned.
Step three: Measure the distance between the outermost 2.5x7.5 cm bars and cut two pieces of this length from 2.5x10 cm boards. They will serve as lower supports for the bench. Secure them by screwing self-tapping screws into each longitudinal rail.
Step four: Using a Kreg Jig, drill two pocket holes at each end of the support crossbars. These holes will be used to connect to the 2.5 x 7.5 cm edge bars.
Tip: It is difficult to give specific recommendations regarding how far from the edge to attach a Kreg Jig. This depends on the length of the screws used, the exact thickness of the board, etc. We advise you to first practice on unnecessary scraps of boards.
unusual coffee table with your own hands. Photo
Step five: Place 2.5x7.5 cm blanks along the edges of the structure. After making sure that their ends are at the same level, secure them with clamps.
Tip: If you use to make a table soft wood(for example, pine), place unnecessary cuttings of boards under the clamp supports. Otherwise, marks from the clamps will remain on the wood.
Step six: Securely attach the outer 2.5x7.5 cm bars to the base of the bench by screwing 3.5 cm screws into the countersunk holes that you made a little earlier at the ends of the support crossbars.
coffee table made of wood. Master Class
Step seven: Measure the width of the fabricated base to determine how long you need to cut the 2.5 x 7.5 cm blank for the ends of the bench. We recommend that you make a cut with a small margin in length, and then slowly grind off the excess until you achieve the perfect fit.
Step eight: Wet the ends of all slats with water and apply a small amount of Gorilla Glue.
Step nine: Install end boards to their intended place and tighten the entire structure with a belt so that it does not fall apart until the glue has dried. For reliability, you can additionally secure the ends with several finishing nails.
Step ten: Sand the surface of the bench with 120 grit sandpaper to remove any rough edges at the joints. Fill all gaps in the seams and recesses from nail heads (the latter must be recessed into the wood) with putty. Once the putty is dry, sand the surface again, this time with 220 grit sandpaper.
Step eleven: Paint the bench. We recommend that you sand the surface again using 400 grit sandpaper and water before painting.
Step twelve: Install special mounting plates on the lower support crossbars to secure the legs. When attaching them, make sure that you drill holes in places where there are no screws already screwed in. The distance from the fastening to the edge of the base of the bench should be about 2.5 cm. Screw the legs themselves into the fastenings.
Coffee table made of copper pipes. Master Class
The material for making the next table can perhaps be called the most unexpected. This time we decided to tell you how to make a table with your own hands from... copper pipes OK.
Materials and tools:
The figure below shows all the parts (pipes (A-E) and various connecting elements (F-H)) with their sizes and quantities. All that remains for you is to take it in your hands pipe cutter and sit in front of the TV, which will brighten up the tedious cutting process a little. It's not difficult, just a little boring. 😉
When all the pieces are ready, you can begin assembling the lower part of the table. How to do this is shown in the figure.
Having assembled the lower tier, you can proceed to the upper one. The only parts not listed in the parts list are the four 2.5cm pieces of pipe that fit into the tees at the top of the corner posts. Without these inserts you will not be able to put on decorative caps, because... the latter have the same diameter as the tees.
Reliable connection of the tubes with each other will ensure glue, but we recommend applying it only after pre-assembly designs, i.e. after you make sure that all the cut tubes are the correct length and fit together well.
Wooden shelves, which you can pre-paint if you wish, are secured using special clamps that are placed on the underside of each board. Now you're ready to decorate your home with a new, handmade table!
DIY lightweight cement table
Concrete countertops and other interior elements in Lately are becoming more and more popular. However, for all their attractiveness, they are not without a number of disadvantages. Firstly, pouring large quantities of concrete can sometimes be quite an expensive undertaking. Secondly, if we're talking about about small side tables, another one comes to light serious problem- such furniture turns out to be too heavy. On the one hand, there is a desire to get a good, solid thing, on the other hand, you want to be able to move a table you made yourself without the help of professional movers. The solution found can be considered an insight.
Materials and tools:
Step one: Mark and cut out the foam sheet. From a 120x240 cm piece you can cut 18 squares of 40x40 cm. By stacking them on top of each other, you will get a parallelepiped 40x40x45 cm.
DIY foam table. Photo
Step two: Glue the cut pieces together. 3M Super 77 aerosol adhesive is ideal for this. It is better to perform this stage of work outdoors. Don't forget to wear gloves and a long sleeve shirt. Apply an even layer of glue to one side of the first square, then do the same with the second. Wait ~15 seconds, then connect the squares, making sure their edges meet. Repeat this until all the square pieces are joined into one piece. Wait about 30 minutes before moving on to step 3.
Step three: Now the most interesting thing... giving the resulting parallelepiped the outline of the future table. We decided to make a table in the shape of a cylinder. You can come up with something more original or, on the contrary, keep the original block with right angles. Cutting foam is easy and fun. Your design will have a rough, angular appearance at first, but don't worry! Once the table has been given the desired shape, it is time for sanding. Using 36 grit sandpaper will quickly smooth out any rough edges. As you get closer to the ideal, gradually move on to sandpaper with a finer grain size. Do not strive to achieve a super smooth surface; at this stage it is important for you to achieve only the required shape.
Step four: The surface of the future table has been sanded, it’s time to cement it. The first layer, applied over the entire foam mold, will fill in the voids and texture of the foam. You only have ~20 minutes, so work quickly so you have time to smooth out any rough edges. Once the applied cement mortar has dried, you can apply the next layer. The number of layers depends on how smooth and flat surface you want for the final finish (usually four to five coats are required). It should be remembered that the smoother the surface of the final layer before it dries, the less sanding it will have to do!
Tip: When cooking cement mortar follow the manufacturer's instructions. You should not prepare more mortar than you need to apply one layer (for example, we used 220 ml of water and 450 g of cement). Make sure you don't forget to cover the surface of your workbench or workshop floor, because this job is quite dirty.
Step five: After the last cement layer has dried, you can sand the surface if desired. We wanted to achieve a glossy finish on at least the top of the table, so we sanded it using varying grit sandpaper ranging from 100 to 2000 grit.
Advice: If you are planning this operation, purchase a protective mask that will help you protect your lungs from cement dust
(The table made in this project turned out to be very durable and strong, but at the same time it weighed no more than a kilogram.)
DIY stump table
The material for the next table is sometimes literally lying under your feet. Even residents of megacities will be able to find a suitable stump if they wish.
log table. Photo
Materials and tools:
- wooden block;
- white acrylic paint;
- hand grinder;
- chisel;
- hammer;
- decorative upholstery nails;
- molar tape.
Step one: Find a table base! This should not be an old rotten stump, but a freshly cut log. Allow it to dry for at least 6 months (nothing is worse than waiting, but it must be done) until the bark begins to separate from the trunk.
Step two: Using a chisel, use a downward motion to carefully scrape away the bark from the log. If the stump is dry enough, you won't have to use too much force to do this.
Step three: By using grinder with medium-grit sandpaper, sand the surface, removing any remaining bark and smoothing sharp corners. Don't forget to sand the surfaces of the lower and upper cuts. Wipe the wood with a damp cloth.
Step four: It's time for painting. We used white semi-gloss paint that included a primer (we needed three coats for full coverage). You can choose a different type and color of paint, focusing solely on your taste. Don't forget to prime the surface of the wood first. Make sure you don't forget to trim the bottom cut.
Step five: Prepare decorative nails. Place a strip of masking tape along the top edge of the side surface of the block, thereby marking the place where the first row of nails will be located.
Step six: Use a hammer to hammer in the first row of decorative nails. To ensure that the distance from them to the top edge is the same throughout the entire “line” of nails, use the strip of masking tape you previously glued as a guide. Once the first row is completed, repeat with the second and third row of nails (we needed almost 150 nails for three rows).
Tip: Cover the bottom surface of the stump with furniture felt so that you can move the table around the room without damaging the flooring.
The work is done. You can enjoy your new piece of furniture and be proud that you made this charming coffee table yourself.
Coffee tables: do it yourself
Wooden table: how to make?
Many people are interested in how to make a wooden table with their own hands to get a model with an original appearance. Let's consider one of the options.
To make an original coffee table with your own hands, you should take timber with a section of 5x10cm. It is cut into pieces of the following lengths: 130cm - 9 pieces, 21cm - 12 pieces, 34cm - 2 pieces.
The prepared timber is placed in three rows, leaving space for attaching the legs.
The top two rows are removed. The timber in the third row is moved slightly to create an interesting appearance. Next, mark the places for attaching the transverse parts.
Lay the outer bars of the second row and mark the places of cuts. Then the cuts are made circular saw or a hacksaw with a chisel.
The bars of the second row are secured with screws.
Lay the third row, move the parts and secure them.
An empty space is formed under the tabletop, in which they fix legs.
The wood is processed protective composition , preserving the wood texture.
Original model of a wooden coffee table with your own hands
First, to make a table with your own hands, prepare planks: 6pcs - 22.5x45cm, 2pcs - 22.5x41cm, 8pcs - 20x4cm, 8pcs - 40x4cm.
Planks 20x4 and 40x4 are glued in pairs. To ensure they stick together securely, they are clampedclamps.
While the leg blanks are drying, assemble box from the remaining parts. They are connected with wood glue and nailer.
Legs They are attached to the box with countersunk screws. Crossbars are placed between the legs at the bottom.
cover for a table made of wood is also made using planks 22.5x45cm. They are glued together, and then the resulting square is sawn into two triangles.
One triangle is secured with screws, and the second triangle is secured with slats so that it is removable.
All parts are sanded and painted.
Stylish coffee table. Master Class
Manufacturing begins stylish table do it yourself from sheet markings Chipboard 16mm thick. The center is found on the sheet at the intersection of two diagonals.
A nail is driven into the center, to which a thin rope or harsh thread is tied.
A pencil is tied to the free end. This allows you to draw a circle.
If you want to make a table with your own hands that is not round, but of a more interesting shape, then the shape of the circle is changed by drawing curves.
The table top is cut out jigsaw or a reciprocating saw.
Edges are processed sandpaper.
Legs secured with screws. If they are located obliquely, then the slope should be outward.
Table surface paint in the desired color.
Simple coffee table
To make a coffee table with your own hands, take boards 40x15cm - 2 pieces and 50x19cm - 2 pieces. In addition, you will need legs and mounting plates.
A larger one is fixed on one of the boards plates for attaching legs. You should step back a little from the edges.
Lateral and top part The table is secured with wood glue.
It dries in about half an hour.
DIY log table
A self-made coffee table with this appearance will decorate your cottage or country house. Work begins by assembling the frame. To do this, take sheets plywood two centimeters thick. A base with dimensions of 60x80cm is cut out of them. A box 68cm long, 45cm wide and 40cm high is attached to the base.
DIY log table. Photo
After this, thirty round pieces are cut logs 45 cm long and twenty-four round cuts, the thickness of which is 3 cm.
The prepared logs are secured around the perimeter of the box. Fixed from below to the base rollers. They are installed at a distance of three centimeters from the edge.
In addition to glue, it would be useful to secure the logs with screws from below.
Installed on the box plywood cover. Round circles are glued onto it. The space between them is filled with wood putty, which does not shrink when dried. Apply it in stages so that the previous layer has time to dry.
After the putty has dried, the surface polished. For this, a surface grinder is used. After this, the log table can be used.
Country style table
If you are interested in how to make a table from wood cuts with your own hands, then you should read the instructions.
They begin making such a coffee table with their own hands by choosing the appropriate material.
Selected slept We inspect for any interesting parts or parts that need to be removed.
Excessively rough, protruding parts are cut off. On the side where the tabletop will be, the surface level.
Used for work cleaver, which moves at an angle of forty-five degrees.
The sides also need to be leveled.
All surfaces polished, using ever-decreasing grain sizes.
Glossy varnish mixed with resin in equal parts.
The resulting composition is applied to the wood in a thick layer. It will take a long time to dry. If cracks appear during the drying process, they must be filled.
Bottom side clearing out. If there are voids in the tree, they are filled with resin gradually until the hole is filled.
If there are air bubbles in the dried resin, the surface is heated with a heat gun or burner.
A second layer of resin is applied and again left to dry for two days. The entire surface of the tabletop should be glossy.
The part of the ax handles is cut off at an angle of 22 degrees. The surface is sanded and painted in the desired color.
Mark places for legs and make holes.
Glue is poured into the holes and the legs are installed. Special pads are attached to each.
White coffee table
Make such a coffee table with your own hands from plywood And glass First, prepare a drawing and determine the dimensions. Then they proceed directly to production.
DIY coffee table. Blueprints
Plywood acts as a tabletop box with partitions, covered with glass on top. Triangular legs are attached to it.
You can make a door at the box to access what's inside, or you can lift the glass.
LegsFor a table with your own hands, it is better to cut it out of fairly thick plywood. It must be remembered that double legs are easier to make than large quantity single.
When all the parts are ready, they are assembled together and fastened. The table is painted or varnished.
DIY table made from pallets
If you know how to make a table from pallets with your own hands, you can get interesting option furniture for home. Pallets must first be sanded, sawn into pieces and primed.
table made from pallets. Instructions
A table is assembled from the prepared material. To do this, attach legs or wheels. A pallet directly or a surface assembled from individual planks can be used as a table cover.
After all the parts are connected, the structure needs to be painted or varnished. After this, the table made from pallets is ready.
Second version of a table made from pallets
To make such a table with your own hands, you will need one or two pallets. You should first draw a sketch of the future product, taking into account all dimensions.
The table will have a shelf for small things under the table top. The structure is assembled from prepared parts.
The surface is painted black, but this is not the only possible variant. There are many other decorating possibilities.
Coffee table stand
Option on how to make a table from copper pipes with your own hands, may be of interest to many craftsmen.
The pipes are first marked and cut. Then they are coated epoxy glue and assemble the base for the table.
This base is applied to the board and the fastening points are outlined. In these places you will need to drill holes by pipe diameter.
Four holes are drilled, but not all the way through.
The board is impregnated polyurethane and cover stain.
The remaining one is collected from the pipes frame.
Legs and base cover paint in the color of the tabletop.
Made from a piece of cloth pocket, which is hung on the transverse parts of the legs.
All parts are assembled together, adding epoxy glue for reliability.
DIY marine style table
This table is from an old one window frame looks very romantic. The frame is cleaned of dust. If necessary, replace the glass.
Wooden surface paint white acrylic paint. After drying, the paint layer is sanded so that the wood appears. An option is also available in blue and white.
To make the legs, take stalk and sawed into pieces of 34 cm. After this, it is treated with sandpaper to remove roughness.
The blanks are drilled in four places. Next, each leg is attached to the base, and the base with legs is attached to the frame. All this is done with self-tapping screws.
The legs are covered with coarse rope.
For peeled and low-fat glass glue sea souvenirs and seafood. They must be covered with glass on top, which is cut in the workshop to the size of the frame.
A loop is made at one end of the rope. The rope is glued around the perimeter of the frame, leaving the loop free. When the other end reaches it, an interesting sea knot is tied.
It's hard to be a fan design solutions For home furniture, while not having enough available funds to purchase them. The point is not only in the level of your income, but also in the price tags that are typical for such furniture, because they are often several times higher than for traditional options.
You can solve this problem by making a coffee table with your own hands. You will be pleasantly surprised at how simple and fun this can be.
Low table
Most often, this option is found among coffee tables. They are not new, they have just recently begun to receive more attention from the public.
They gained popularity two centuries ago, when tea lovers - the British - began to use them. A hundred years later, this trend has spread to other countries of the world, including ours. Now this is not a very popular option, however, it has the right to life.
Chipboard table
Simple and enough practical option maybe a coffee table made of chipboard, which you can make yourself without any problems. Now on the furniture market, chipboard is one of the most available materials, which can be used to create a traditional table. We'll talk about why traditionally later.
The price tag for this option will be significantly lower than if your choice falls on a wooden coffee table. It is best to take sheets coated with laminate or varnish. Still, you will be placing such a table in your home, and therefore you need to pay attention to the aesthetic component.
Then everything depends more on the design you choose. A simple, yet small table can be made from several parts. This option will be small and with several shelves. Perfect for the living room, and will stand next to the sofa or armchair.
The shelves are well suited for magazines and remote controls for controlling equipment. This reduces the likelihood that they will get lost.
Glass table
Drawings of such coffee tables can be easily found on the Internet. You just need to take into account one feature - in almost any case you will need to buy a glass part of the table. You can solve this issue with the help of old glass, which may be in your barn or garage.
The main part of the table can be made from a material that suits you, and cover it with a sheet of glass on top. To do this, you need to cut it to shape, then process the edges and secure it to the main structure.
Even if you don’t make such a table entirely from glass, with the exception of the frame, you can get a very attractive and interesting result that will look good both in a modern interior and in the usual apartment design without any special features.
Wooden table
Enough detailed instructions How to make a coffee table out of wood can be found on the pages of thematic magazines. This option will be more expensive than with chipboard, but the appearance pays for everything. This material is better suited for large tables, at which, if necessary, you can work or use them to store documents that you view while sitting in front of the TV in the evening.
The design can be tritely simple: four bars for the legs, which are complemented by a tabletop of the desired shape. Depending on the latter, you can take three legs, which will look even more interesting.
On top of this you can add various decorative and functional details - be it shelves or decorations. Here you can give freedom to your creative nature.
Unusual table options
You may have often come across photos of coffee tables that are made from unusual materials. This can easily include a table made from an old suitcase.
The most interesting thing about this is that you will have to do practically nothing to create such an item. All you have to do is restore a pleasant appearance, if required at all, and install such a table.
A huge advantage of this solution will be the intelligent use of space in the room. This would work well in front of the sofa, while the space inside the suitcase would also be good to use. You can put some kind of blanket or boxes of shoes there. In general, here it comes down to personal choice; in any case, it is very convenient and practical.
Table made from scrap materials
Separately, I would like to consider a coffee table made with my own hands from scrap materials. There are several options that I really liked, and I want to share them with you.
The first one is a table made of pallets. They can be found in any supermarket or warehouse, and therefore it will not be difficult to get them. They are made of wood, which is very good for the interior. This wood can be varnished, which will greatly change its appearance.
Take two of these pallets, or trays, whichever is more convenient for you, place the first one with its legs up, and place the second one on top so that the legs meet. They can be additionally connected with self-tapping screws, and a sheet of glass can be placed on top of them. The option is very beautiful and easy to implement.
As you already understand, I prefer the options when I don’t have to deal with the work of furniture companies, and cut out all the parts, and then customize them. I am more interested in creative and fresh solutions.
For the second option, you will need only four old boxes, which, when placed on their sides, need to be connected to each other clockwise. We first coat them with varnish, connect them and that’s it – the table is ready. The empty space inside can be covered with a tree and a flower placed on top. Good luck with your choice.
DIY photo of coffee tables
