Many are concerned about one important question, how to solder a gas tank? Various breakdowns of the car can catch the driver at any moment and most likely you will not even expect it. One of the most serious problems is the breakdown of the gas tank. It needs to be solved very urgently, and at least partially.
In fact, fixing a gas tank is not so difficult for a person who is at least a little versed in mechanics and held in his hands blowtorch... If you are unfamiliar with how your car works, then you have to learn, because the problem is really very serious. Many people ask the question: "How to solder the gas tank yourself?" First you need to know where he is. It is often located in the right corner of the rear section of the vehicle.
Due to this arrangement, the gas tank can ensure the safety of the driver and passengers. Find it and examine it carefully.
Your task is to understand what is the cause of the breakdown and where is the hole that needs to be soldered. After all, it is Bottom part the car most often suffers from physical stress. But here the driving style can also serve as a breakdown factor; if you drive carefully, then most likely this problem will bypass you. The only place to expect it from is corrosion and rust. Time will take its toll, especially on domestic cars.
Fast work
How to solder a gas tank if an accident happened on the highway? First, drain all the fuel that is inside. You will need a jack to tilt the vehicle, and then the pipe can drain the fuel. But even after that, do not start work, you need to wait until the gas tank is completely dry, otherwise it may ignite.
Further, assess the damage to the gas tank and identify the place of failure. Your task is to carefully remove it for repair. When the part is removed from the car body, you need to determine if there are additional holes in the gas tank. The process is quite delicate, so it's better not to rush here. It is necessary to carefully detach the gas tank from the car and carefully inspect it. Only then can you start working.
Exceptions
There are several types of critical gas tank breakdowns, but they are often solved in a simple way. If a breakdown occurred while driving, and you are on the track, it is better to first install patches on the gas tank. This can be done using only a wrench..
With the help of tools at hand, it is necessary to widen the hole in the hole so that the bolt can be inserted into it. Then put on it a washer with an elastic band or a tight gasket, and then insert this structure into the neck.
Also, from the outside of the gas tank, it is necessary to install a special cuff with a washer, which will simply be tightened with a regular nut. Such a design will help you get to the car service, where the specialists will already carry out the main work.
A simple solution
In some situations, you can eliminate a hole in the gas tank using good glue or any equivalent. In case of not very serious damage, this method will be most relevant. All you need is a good piece of cloth, which must be moistened with glue and applied to the damaged area.
When you see that the fabric has adhered tightly to the damaged area, treat it with nitro paint, this temporary fix will allow you to easily reach to the nearest car service.
After these tips, you most likely will no longer ask: "How to solder the gas tank?" Now you can independently carry out repairs at any time and protect yourself from even greater damage to the gas tank.
Is it possible to glue a plastic container or gas tank at all?
How to solder a plastic container? Nowadays, there are many invented ways of welding cracks, holes, burst seams, the equipment for such repairs is also varied from a soldering iron to a hair dryer, who is in that much. It can be repaired with such tools, but where is the guarantee that it will not flow again. Such repairs will be just decorative and in the future the owner will incur new costs. It takes knowledge of the material and practice. Our masters enjoy professional equipment a well-known Swiss company and give a guarantee for the repaired container, reservoir, tank, plastic gas tank.
Plastic containers are made mainly from materials such as polyethylene and polypropylene, it is almost impossible to glue anything to these materials, due to their chemical characteristics, and trying to seal a container from these materials is a waste of time.
With large volumes of plastic containers from 2 cubes, this type of repair will not help at all, in this case, only welding with special equipment that will ensure the sealing of the container!
How to seal a plastic tank
How to seal a plastic tank?
Usually the issue is solved using a plastic container repair kit, but remember, if you want to use this method for a long time, such a repair will not help you. All capacitive products in 95% of cases are made of two materials: polypropylene (PP) and polyethylene (PE), which in turn have very low adhesion, that is, are very resistant to chemical influences. Almost not one glue is glued to them, and not one patch with the help of glue will provide quality repair, professional repair by welding required!
How to seal a plastic gas tank?
How to seal a plastic gas tank is a serious question, not every car service has specialists who can restore a plastic fuel tank, and besides, give a guarantee for sealing! You can repair it with your own hands, for this, again, you need equipment and a simple construction hairdryer is unlikely to save you, where will they give you a guarantee for your repair? Our workshop both repairs and gives a guarantee for the repair of the fuel tank, specialists go to the place of repair, if necessary, by agreement.
Repair of any type of gas tank without a trip to the service station
Car breakdown is a fairly common occurrence that can catch the driver in the most unforeseen situation. Failure of the gas tank - serious problem, which must be at least partially eliminated at the scene of the accident. This will allow the car to be transported to the nearest service center, where it will be possible to carry out a major inspection and repair. Do-it-yourself gas tank repair is not too difficult for people with some knowledge of such a repair.
The location of the gas tank is the lower right corner of the rear sector of the vehicle. This is due to the provision of safety for the driver and passengers, as well as the formation of the correct center of gravity in the car, which makes it possible to improve its handling. However, the lower section most often suffers from constant physical impact, which leads to multiple damage to all mechanisms located here. The fuel tank is no exception.
Crack in the gas tank of a car
Causes of damage to the gas tank and the basics of repair
The breakdown of gas tanks is most often associated with the gradual development of corrosion processes. Their effect on the inside of the fuel tank is especially dangerous. The provoking factor for the appearance of rust is water. It is almost impossible to avoid getting it into the tank.
Also, the cause of the appearance of holes in the gas tank may be a malfunction in the power supply system of the vehicle. A discharged pressure forms inside the tank, which provokes the formation of an extreme load on all walls of the fuel tank. After a while, it becomes covered with small mechanical cracks.
Rules for repairing a gas tank of any type:
- Before starting the procedure, all available fuel must be drained from the gas tank. The vehicle is tilted by means of a jack. Gasoline is drained through pipes. Next, the gas tank should be thoroughly dried.
- Determine the degree of need for complete removal of the fuel tank for carrying out renovation works... It is recommended to take into account the area of damage and the degree of convenience in carrying out the repair.
- Determine the feasibility of conducting a complete monitoring of the tank for additional holes.
Gas tank removed for subsequent repair
Ways to repair a fuel storage tank
There are several ways to troubleshoot this problem. Most of them are applicable in extreme conditions, which will avoid spending additional funds to call a tow truck.
Installing the patch using a nut bolt and a rubber gasket. First, you need to use available tools to expand the tank hole to the size corresponding to the bolt. A washer is put on its narrow part with rubber gasket... Then the whole structure is inserted into the hole through the neck. WITH outside a cuff with a washer is installed and tightened with a nut.
The rubber must be petrol resistant. Not every driver has such material stored in the car.
How to repair a gas tank yourself: detailed instructions with a video
A camera from any truck is suitable as a replacement. This patch is considered to be quite durable. At correct installation you can postpone the appeal to the service station. This method is often used by truckers who most spend their time on the road. A good patch can last over five years.
Use for elimination of damage to glue "Moment" or any of its analogs. The method is relevant for not very serious damage. To create a patch, you need a piece of thick, but pliable cloth dampened with glue. It is required to press it firmly to the place of damage and hold it for some time. After the main gluing, the patch should be treated with nitro paint from the repair kit. This is a temporary measure to get to the nearest service station.
On - repair of a hole in the gas tank:
Temporary replacement of the gas tank for any bottle. The method is suitable for the breakdown of the fuel capacity of cars of the carburetor type. Plastic or any other container is filled with gasoline, a hose from the fuel pump to the fuel tank is immersed in it. The container must be securely fastened so that it does not tip over and lead to negative consequences... This method will easily help the driver get out of a difficult situation.
Elimination of damage by laundry soap... The method is considered effective only with superficial problems.
Sealing the crack area with epoxy glue and fiberglass. The gluing site must be thoroughly cleaned and dried, the gasoline must be drained. Work area clean up sandpaper, degrease and dry again. A piece of fiberglass must be glued to the place of damage. After completely dry, stick another patch of the same type. The number of layers must be at least three. When gluing the last layer, a plasticizer should be used, which can be aluminum powder.
Repair of plastic gas tanks and metal gas tanks using the method cold welding... The most versatile way to deal with holes. The damage is removed with epoxy resin... The first stage of work is grouting the surface with sandpaper. Then, in a separate bowl, epoxy resin is mixed with a hardener until a homogeneous mass is obtained. If heating is required, the container can be placed on the engine. This method also uses a fabric patch. Soak it liberally with the mixture and apply it to the hole in the fuel tank. Let dry well. This patch is very strong and can last a long time.
The result of repairing a gas tank with cold welding
Soldering as a type of gas tank repair of any type
This method of eliminating the hole is the most sustainable. Suitable for both metal fuel tanks and plastic ones. Knowing how to solder a gas tank, you can prolong its service for a long time without buying a new unit at a car shop.
Repair of a plastic gas tank is carried out using a soldering iron, the power of which is 250 watts.
The procedure itself resembles soldering. plastic bumper... Soldering is done with outside... It is necessary to control ensuring the tightness and strength of the structure. If additional donor plastic is used, its type must correspond to the original representative. Plastic composition markings are usually present on every part. It can be polypropylene (PP), acrylonitrile butadiene styrene (ABS) or polyamide (PA). A metal or copper mesh with a fine pitch is used as a reinforcing material. The necessary piece of it is applied to the cleaned surface and, with the help of a heated soldering iron, is fused deep into the plastic. Residues of plastic on the surface of the mesh are gently smeared, creating a surface layer. The entire operation must be carried out at one time, otherwise it will not be possible to avoid the influx of multiple layers of plastic.
For repairing a metal gas tank, only a soldering iron with a power of 500 watts is suitable. An ordinary iron can help warm up the body of the gas tank. If necessary, a thin copper sheet can be used for the patch. The solder must be low-melting. The patch is soldered along the entire perimeter, which contributes to the tightness and reliability of the fastening. Before soldering Workspace processed with soldering acid. This is necessary for the reliability of the connection of solder and metal. Above the superimposed patch is covered bituminous mastic characterized by special resistance to corrosion.
The result of repairing a gas tank by soldering
How to put the gas cap back on line
You can pay attention to a malfunction of the gas tank cap if, when opening it, there is a noise effect associated with the suction of air into the container.
Repair of the gas tank cap is often associated with malfunctions of the plastic leash. You can replace it with ties that hold the wires together. For work, you need three clamps. Insert one of them into the lug of the fuel tank cap and tighten the tight loop. Connect the second clamp to it. In the loop of the gas tank flap, make a small hole to which to tie the loop knot. The second end of the clamp, located on the gas tank cap, will be tied to it.
The knowledge of the peculiarities of repairing a fuel tank is extremely useful for the driver. Understanding the repair issues, not a single motorist will be caught by surprise, even far from civilization.
http://365cars.ru
How to glue the aluminum tank
What are the effective methods and how to glue the gas tank for the possibility of its further operation? Similar questions will be discussed in this section. After all, this topic is more related to used cars, and even then domestic production. Structurally, gas tanks are practically not protected from external damage, in contrast to their foreign counterparts. Often, fine fractions of gravel, crushed stone, asphalt bouncing off the rear wheels gradually ruin the paint and primer shell, causing irreparable damage to the metal. After a while, the metal starts to rust. The driver begins to notice a fuel leak. How to glue the gas tank? Today there are two options for gluing:
Each method is good in its own way. Of course, you can find other ways to eliminate leaks in the gas tank, but they are less effective than the above.
- Half a liter of acetone;
- Epoxy resin;
- Fiberglass.
First, we purchase all the above materials, carefully read the conditions of the instructions for use. Troubleshooting Algorithm
- Degrease the surface of the gas tank with acetone.
This procedure must be carried out several times, since the quality of gluing the material of the gas tank depends on how well the degreasing is carried out;
Preparation step and epoxy bonding For bonding, a viscous adhesive must be used, otherwise the effect may not be achieved.
- We cut scraps of fiberglass so that they protrude 1-2 cm more than the perimeter of the crack or other damage. We saturate the scraps of fabric carefully in an eboksitka;
Each subsequent layer should be slightly wider than the previous one and with an interval of 15-20 minutes. In addition, the last layer should be impregnated with additional aluminum powder, which can be purchased at a car dealership. After a day, the structure will completely dry out and harden. You can process it with fine sanding paper. We proceed to painting or priming, depending on the need. We apply cold welding in the same way as above. In spite of Hi-tech in the form of welding, many drivers prefer the old proven and durable methods. So, the question of how to seal the gas tank has already been disassembled. You can carry out a similar procedure as in garage conditions, and at a car service, depending on your decision.
The reasons for damage to fuel tanks can be different, in one case, rust, in the other a normal trip on Russian roads. A small blow and almost immediately we begin to smell the smell of gasoline in the cabin. The fuel level arrow also tells us that gasoline is leaking out. How difficult is it to repair a fuel tank yourself? If the gas tank leaks, then it is not safe to drive with such a breakdown, so do not postpone its repair for for a long time... Before starting work, it is recommended that you familiarize yourself with:
General rules for repairing a gas tank
- To drain the gasoline from the fuel tank, you need to tilt the car to one side with a jack and use a pipe. If the hole in the gas tank is in the lower part of it, then it will be faster to drain the gas through it. Then you should dry the gas tank from gasoline vapors.
- Repair of a gas tank without removing it, or it is better to dismantle it, is decided depending on the availability to the place of damage and the type of repair work.
The popular way to repair a gas tank
Do you know how they used to repair a fuel tank in field conditions our grandfathers? If a small crack appeared in the fuel tank, then the hole was given round shape with a screwdriver. Next, we selected a bolt of a suitable size for this hole and tightened it, first we put rubber washers on it (from the wheel chamber).
If you look at the old 130th ZILs, you will notice that their tanks are completely pitted with bolts, which suggests that this method is quite reliable and durable. Currently, this method finds its favor among truckers, but the most popular and all affordable way we will analyze the gas tank further:
Gas tank repair by cold welding
This way on this moment remains the most popular cut by car enthusiasts. It is based on a material called "cold welding", which can be found in any home store. The meaning of this tool is that when the two components are mixed, the resulting plasticine-like mixture hardens after 10-30 minutes, which is ideal for patches. damaged surface first clean it from dirt and dry it, then the repair by cold welding will be quite durable, and you are unlikely to ever return to this damage. However, if you try to plug a hole in the gas tank without preliminary preparation then such treatment will be temporary. 
Repair of a gas tank by soldering
For this method, you will need a soldering flux (fat, rosin) and a hammer soldering iron (200 W). We clean and degrease the space around the damaged area, and thoroughly rinse the tank with water.
We process 20% phosphoric acid and solder two galvanized patches (flux-hydrochloric acid with zinc, pos-40 solder). Smoothen and tin the seating surfaces of the patch and the tank.
DIY gas tank repair
Such a repair of a punctured gas tank can be called reliable, but the disadvantage is the obligatory dismantling of the tank.
Fiberglass and epoxy gas tank repair
Another way to fix a gas tank leak. In this case, fiberglass and epoxy will act as a patch. In a similar way, we clean the surface, and then apply a layer of fiberglass, which we impregnate with resin. After drying, apply the second layer in the same way. The final stage will be anticorrosive treatment. The gas tank was repaired in 4 hours! 
In the field, instead of epoxy and fiberglass, Moment glue and any material (rag, rags) are used. The layers are alternately impregnated and applied to the damaged area. Such a temporary solution allows you to easily reach the nearest service station.
xn - 2111-43da1a8c.xn - p1ai
Dear visitor! You are in the archive of the old forum site mastergrad.com
How to glue a plastic tank
| snim (Moscow) Feb 9. 2004 08:32:33 |
I burst a tank made of a material very similar to the one used for making car washer tanks (white fragile plastic). How to repair a fuel tank. DIY gas tank repairCrack 10-12mm. |
| Anton (moscow, russia) Feb 9. 2004 12:02:33 |
This is most likely polyethylene or something similar. The only solvent is a soldering iron. |
| Destroyer (Moscow) Feb 9. 2004 13:44:46 |
Right: I need a thermal gun and a hair dryer. We expand the crack to 2mm, the edges are chamfered. We put a smooth metal plate on the outside, heat the tank around the crack with a hairdryer, so that it does not flow yet, but already hot, fill it from the inside with a thermal gun from the inside. It cools down, we cut off the excess. We insert the plate from the inside, heat it with a hairdryer from the outside, Fill it with a thermal gun from the outside. Refills for a hot air gun different color, with different properties, explain to the seller where this tank is used, pick it up. |
| Alex21 (Volzhsky, Volgograd region) Feb 9. 2004 15:48:32 |
This plastic cistern is utter rubbish ... Plastic ages from time to time (your thorns are most likely the first swallow), as a result, it can burst at the same time along its entire height with pouring the contents onto the floor. An acquaintance did just that - she was well at home, she heard the whistle of water from the valve. |
| snim (Moscow) Feb 9. 2004 19:56:00 |
2Destroyer: Will not work from the inside 🙁 The throat of the tank is 5 cm in diameter. > Even easier, without a heat gun: Roll up plastic bag(which is thin, without a pattern) into a thin tight tube, light it, drops begin to fall from it. Wo, I'm going to try it now. But it will stink ... > Generally elementary: buy a new tank No, no easier, it is specific, from a sprayer. I watered the wallpaper with water, primed the walls ... Hello, Alexander!!! :-) > Untold rubbish, this plastic tank ... Maybe yes. > Plastic ages from time to time ... No, it’s new, it’s not even a month old, but it’s burst, an infection. I think I hit him with something. |
| Serg (Samara, Russia) Feb 10. 2004 02:33:43 |
2snim: Buy a hot melt glue stick and use a soldering iron or just a hot nail (like a spatula) to seal the crack with it. Only, initially, it is necessary to degrease the surface of the crack - you can use acetone. Best regards, Sergei |
| snim (Moscow) 11 Feb 2004 |
Thank you all for the advice. The gluing was done with a heat gun. Only here is a nuance: there were 2 rods - one transparent, the other matte. The first did not stick, the second was patched tight! With respect, Nicholai. |
| Voka (Tomsk) Feb 12. 2004 07:46:45 |
Late, of course, but ... It is advisable to drill the ends of such cracks. So that it does not creep further. |
How to glue the gas tank? 2 time-tested ways
What are the effective methods and how to glue the gas tank for the possibility of its further operation? Similar questions will be discussed in this section. After all, this topic is more related to used cars, and even then domestic production.
Structurally, gas tanks are practically not protected from external damage, in contrast to their foreign counterparts. Often, fine fractions of gravel, crushed stone, asphalt bouncing off the rear wheels gradually ruin the paint and primer shell, causing irreparable damage to the metal. After a while, the metal starts to rust. The driver begins to notice a fuel leak.
How to glue the gas tank? Today there are two options for gluing:
- Using cold welding to seal the crack and hole;
- Epoxy glue or popularly called fiberglass. Better to buy a two-component.
Each method is good in its own way. Of course, you can find other ways to eliminate leaks in the gas tank, but they are less effective than the above.
Tools and related equipment
- Several sheets of sanding paper;
- Half a liter of acetone;
- Epoxy resin;
- Fiberglass.
First, we purchase all the above materials, carefully read the conditions of the instructions for use.
Troubleshooting Algorithm
- We drive the car to inspection pit or overpass;
- We outline the place of leakage with chalk;
- We dismantle the fuel tank from the car;
- Pour out the remains of gasoline or diesel fuel;
- We dry it in the open air, since the vapors of the chemical reagent are explosive;
- Using rags and soap solution externally we clean the gas tank from resin residues, dirt, and other impurities;
- For cleaning difficult to remove chemical compounds we use rough sandpaper;
- Degrease the surface of the gas tank with acetone. This procedure must be carried out several times, since the quality of gluing the material of the gas tank depends on how well the degreasing is carried out;
Preparation phase and epoxy bonding
For gluing, it is necessary to use glue of a viscous consistency, otherwise the effect may not be achieved.
- We cut scraps of fiberglass so that they protruded 1-2 cm... more than the perimeter of a crack or other damage. We saturate the scraps of fabric carefully in an eboksitka;
- Gently put the fiberglass on the surface of the gas tank so that no air bubbles remain, otherwise eliminate the imperfections;
- Remove excess glue and resin with a rag;
- Smooths the glass strip with a small piece of plastic to keep the platform flat;
- After that, we proceed to the imposition of the second ball, we carry out a similar procedure. Depending on the degree of damage to the gas tank, it is determined with the number of balls of fiberglass. Accordingly, minimal damage will require minimal amount balls of fiberglass, deeper affected areas will require more balls.
Note to the driver, it must be remembered that the quality of the rest of the structure depends on how the first layer is laid.
Each subsequent layer should be slightly wider than the previous one and with an interval of 15-20 minutes.
In addition, we impregnate the last layer with additional aluminum powder, which can be purchased at a car dealership.
After a day, the structure will completely dry out and harden. You can process it with fine sanding paper.
We proceed to painting or priming, depending on the need.
We apply cold welding in the same way as above. Despite the advanced technology in the form of welding, many drivers prefer the old proven and durable methods. So, the question of how to seal the gas tank has already been disassembled. You can carry out a similar procedure both in a garage and at a car service, depending on your decision.
Is it possible to glue a plastic container or gas tank at all?
How to solder a plastic container? Nowadays, there are many invented ways of welding cracks, holes, burst seams, the equipment for such repairs is also varied from a soldering iron to a hair dryer, who is in that much. It can be repaired with such tools, but where is the guarantee that it will not flow again. Such repairs will be just decorative and in the future the owner will incur new costs. It takes knowledge of the material and practice. Our craftsmen use professional equipment from a well-known Swiss company and give a guarantee for the repaired container, reservoir, tank, plastic gas tank.
Plastic containers are made mainly from materials such as polyethylene and polypropylene, it is almost impossible to glue anything to these materials, due to their chemical characteristics, and trying to seal a container from these materials is a waste of time. With large volumes of plastic containers from 2 cubes, this type of repair will not help at all, in this case, only welding with special equipment that will ensure the sealing of the container!
How to seal a plastic tank
How to seal a plastic tank? Usually the issue is solved using a plastic container repair kit, but remember, if you want to use this method for a long time, such a repair will not help you. All capacitive products in 95% of cases are made of two materials: polypropylene (PP) and polyethylene (PE), which in turn have very low adhesion, that is, are very resistant to chemical influences. Practically more than one glue is not glued to them, and not one patch with the help of glue will not provide a high-quality repair, professional repair by means of welding is necessary!
How to seal a plastic gas tank?
How to seal a plastic gas tank is a serious question, not every car service has specialists who can restore a plastic fuel tank, and besides, give a guarantee for sealing! You can repair it with your own hands, for this, again, you need equipment and a simple construction hairdryer is unlikely to save you, where will they give you a guarantee for your repair? Our workshop both repairs and gives a guarantee for the repair of the fuel tank, specialists go to the place of repair, if necessary, by agreement.
Buckets, basins, barrels and other household equipment are made of plastic. This material is practical, easy to use, but short-lived.
Any fall or mechanical impact can lead to cracks. And a container that allows water to pass through becomes useless. But seal the plastic water tank it is quite possible that it will serve properly for some time.
Glue plastic barrel quite possible at home. Let's consider two options for how you can eliminate gaps in plastic drums and other containers.
Option 1
For work you will need the following materials and tools:
- stainless steel mesh (you can take aluminum, copper),
- scissors,
- soldering iron 100 watt.
Operating procedure:
- Cut off a piece of mesh with scissors.
- We fix the mesh at the site of damage to the depth of the mesh thickness.
- We align it along the seam, moving along the entire plane. At the same time, in parallel, we solder the mesh with a soldering iron, hold the free edge with a knife, immediately after soldering, cool it with a heat exchanger (knife) - this is important rule so that the mesh does not bump.
- Using this method, we introduce the entire mesh into the seam.
- At the end of the work, the seam is completely sealed and reinforced, which gives it strength.
- We repeat the procedure on the back of the container.
VIDEO INSTRUCTION
Option 2
If you have to repair a container, the water in which is under pressure, you can resort to another method.
For work you will need:
- flexible plastic patch,
- construction hair dryer,
- protective gloves.
Operating procedure:
- We wipe the damaged area, remove dirt.
- We start heating with a hair dryer at low power, so as not to burn a hole, a place with a defect.
- Heat the patch on the side that will adjoin the crack with a hairdryer. We are already heating at a higher power.
- We apply a patch to the place of damage and continue to warm it up with a hairdryer, adding more power. Wear protective gloves on your hands to avoid scalding. It is important not to overheat the surface.
- Smooth the patch with your fingers and wait for it to cool. We fill in water and check the quality of work.
Final sealing and smoothing of irregularities on the repaired plastic tank The first technique has proven to be the most effective in practice. The second is more suitable as a temporary measure.
How to glue a plastic tank or barrel for water - the choice of an epoxy
If the defect is plastic container small, you can use epoxy glue. Two-component epoxy adhesive can effectively solve the problem of a leaky plastic tank.
Differs in increased resistance to moisture and chemicals, polymerizes in just 1 hour, non-flammable.
Need to cut off the right amount glue, knead clean hands until a homogeneous mass is obtained, mold a cone out of it and insert into the opening of the tank. Fix securely for a few minutes.
Then you need to wait 2 hours, after which the container can be used.
Features of epoxy glue "Contact":
- restores the shape of products, as well as hermetically fills in voids,
- not afraid of not only water, but also oils, solvents,
- the repaired tank can be used at temperatures from -40C to + 150C,
- within 3-5 minutes, the glue lends itself to correction, and after an hour it can be cleaned, grinded and subjected to other mechanical influences,
- the glue is sold ready-to-use.
The cost of this composition is from 150 rubles per package of 50 g.
Also, similar properties are possessed by adhesives "General Purpos Permapoxy PERMATEX"(from 314 rubles for 25 ml) and Plastic Weld Permapoxy PERMATEX (from 320 rubles for 25 ml).
Purchase epoxy adhesives most building stores and also via the Internet.