Very easy in the manufacture of an organizer for small hardware (screws, carnations, washers, nuts, etc.), which can be made literally in a few minutes from cardboard box and plastic jars from yogurt.
As you know, homemade workers who actively use various small hardware in their works (cloves, screws, nuts, washers, etc.), constantly have to solve the problem of their placement and storage.
So I currently had a rather sharply the problem of placing such a small fastener. Moreover, it is largely due to the fact that on the street for the third week there are decent frosts so that there is no possibility to work in the workshop. Therefore, it is imperative to relocate home and at home and work on homemade, at least those that can be made at home.
And so, in order to solve the problem of placing a small fastener at home, I decided to make a fairly simple organizer, and literally from the rubble.
To do this, I needed the following accessories:
Materials:
Cardboard box from milk packages;
- Plastic jars from yogurts.
Tools:
Pencil;
- strong scissors;
- construction or stationery knife;
- stationery stapler.
Manufacturing organizer
First cut off with scissors top Boxes from dairy packages, focusing on the side sides.
Then we enhance the places of gluing the boxes of the box, additionally fasten them with the brackets using the stationery stapler, just in case, so as not to dissolve.
Now, there are a pencil in the bottom of the box, the places of cutouts under jars from yogurt and cut out them with a stationery knife.
At the same time, you can cut out one slot, use the cut part as a template for marking the subsequent slots.
On the accuracy and evenness of the edges of the slots, it is possible not to take care, since they will not be visible anyway.
I made seven slots in the bottom of the box, four slots for small jars from yogurt and three, more for jars.
Now you can insert empty jars yourself into the made slots, which will serve the storage tanks of our hardware.
And here our organizer is ready!
And so, he looks below!
Now, you can fill with jars with hardware.
As a result, it turned out a pretty good organizer!
I, honestly, feared that because of the slopes, the bottom of the box could lose stiffness and become not very strong. But it turned out that the bottom was pretty well preserved strength and rigidity and, in principle, it can easily withstand and even more cargo (if, for example, all jars fill to the top with hardware).
Another convenience of this organizer is that every jar is easily removed from its slot. So, if necessary, any jar can be removed from the slot to replace or transfer to another place.
In addition, such organizers, you can make several pieces and put them one on another.
Reading time ≈ 5 minutes
This owner always takes care of the preservation of its instruments. Even a small set should be stored ordered, neatly. A skilled master can assemble the capacity of the tools and fixtures on their own. Below will be talking about how to make a tool box with your own hands. Presented photos and video will help in work.
Externally, the box looks good and stylish, he immediately declares a serious approach to the life of his owner. Its dimensions (70x40x45 cm), that is, 70 cm in width, 40 cm deep, 45 cm in height. This is quite enough to accommodate hand tool. In the drawer 3 retractable tray, as well as the top folding cover, which opens the bulk compartment. Such boxing allows you to protect the tools from dust, organize safe storage.
Required tools
For the manufacture of a wooden box, the following tools will be needed:
- a circular saw;
- milling machine;
- grinding;
- clamp;
- a hammer;
- nippers;
- file;
- wood hacksaw;
- chisel.
Step-by-step instructions for making tools
Optimal material for the manufacture of frame - oak wood. This is beautiful durable materialwhich is distinguished by strength and resistance to mechanical effects. It is better to take the basis - glued plates with a thickness of 19 mm. This material Does not have bitch and rotten inclusions. Using a circular, a strip of 38 mm wide is cut off.
So that when gluing separate elements It was not shifted relative to each other, in the first part it is a little ripped off the carnations, the pads remove his hat, and then focus on the protruding sharp tip.
The boards are additionally missed by glue and fix.
The glue spoke on the joints of the details is removed by the chisel, only you have to wait to glue a little snack.
As a result, it should be part of 38x38 mm. Her end grind.
The edge should be cut strictly at an angle of 90 °, so cutting off the detail of the desired length, you must not forget about the coal of the cut.
This technique will help make sure the cutting angle accuracy.
The location of each detail is marked in order not to get confused when assembling.
In each part over the entire length, the groove is cut, it must go strictly in the center.
Grooves can be done either using stationary circular sawor with a milling machine.
On the details that are intended for the manufacture of vertical corner supports of the frame, make the transverse markup.
In the rear corner items make another longitudinal groove. In the front corner reference parts it is not needed.
For the subsequent attachment in the end part of the blanks, it is necessary to find the center, noting the point of intersection of diagonals.
It is necessary to carefully check the compatibility of the blanks.
Billets are processed with a file.
In a freely assembled frame, there are marks to subsequently lengthen the grooves.
The grooves are drunk with a tree with a tree.
The chisel is removed all too much.
These billets are needed for drawers. A corner is cut off from the end part.
Each billet is drilled for fastening with bolts.
Observing accuracy, you need to resolve the prepared details.
On the details intended for attaching and separating 2 drawers, cutouts are performed at an angle of 90 °.
By installing the details for the movement of the boxes in place and fixing them, gradually begin to fasten them.
Corners of plywood blanks are cut into the photo.
The walls of the lower boxes are attached to the sheets of plywood using selflessness.
To one side side attached horizontal parts from plywood. At first they do without the use of glue.
During fixation using clamps, you need to check the diagonality to match the sizes.
Retractable drawers are made of plywood.
The grooves can be chopped up either on a stationary saw, or with a cutter.
Details of drawers are fastened with glue.
The side parts of the boxes must have grooves for movement on the planets fixed inside.
For strength, the side parts are fastened with dowels that are cut into the flush.
For reliability when gluing, small carnations are partially driven into the surface of the front wall of drawers, their caps are removed.
Attaching the front panel to retractable boxes, Watch, are smoothly located separate items.
When gluing it is necessary to observe the limit accuracy, there should be no gaps.
At the end make the top frame of the box of plywood.
To make an exact incision at an angle of 45 °, it is desirable to use a special tool.
Billets for the frame are connected and fixed when gluing with a stretch strap.
Life of present homemade Masters Not thinking without large number Manual and mechanical assistants used for wood processing, metal, execution different species work. To store tools are used various devices industrial production and independent manufacture. Among the most common storage and carrying methods special place occupy instrumental boxes.
For independent creation Such products can be used timber or artificial wood materials - chipboard, plywood or OSB plate.
The process of performing such a product allows you to obtain a capacity for the sizes of specific tools, in contrast to the purchased finished boxes. The following readers will be asked to describe the sequence of work on the manufacture of similar boxes.
The product shown below can be used for temporary storage and transfer to the place of work of some tools.
Or stationery, which are often widespread when performing markup.
Making a drawer will require the preparation of the following materials:
- board of coniferous or hardwood with a thickness of 20 x 100 x 850 mm.
- round wooden rod with a diameter of 20 and a length of 260 mm;
- tree screws - 8 pcs. 32 mm long;
- glue on wood;
- sandpaper.
From the tools it is necessary to prepare a ruler, pencil, an electrolovka, a drill, a screwdriver and grinding of any kind.
Work is starting with the markup of the details. To do this, on the prepared rigged board we appline the contours of future parts - end and lateral walls, bottom.
We cut the parts by the electrolybiz, setting the pre-pink for pure cut. The edges and planes of the obtained parts carefully process the emery paper.
AT face walls In the center of N. equal distance From the bottom edge, placing the center and we turn the deaf hole with a depth of about ten millimeters, the diameter of which is equal to the diameter of the round rod. Along the side and lower edges we drill three through holes with a diameter of 4-5 millimeters to install screws. In the same way, we make two holes at the bottom of the future box.
After preparing holes, you can start assembling the product. To ensure maximum strength of the edge of the side walls and the bottom, smear glue, applying it thin layer. The ends of the round rod also pre-cover with glue.
Install the side walls and the bottom of one of the ends to the curly walls and attach the parts with self-draws. Install in the prepared hole of the rod one of the ends. After that, perform the same operations with the second curly wall. To protect the drawer material, treat the surface with a transparent varnish on oil or nitrosnov.
The design of the second drawer for tools is more complimentary, has increased compared to the first dimensions. For its manufacture, they will need plywood or OSB plates with a thickness of 15 and 10 millimeters. It is also necessary to prepare the following tools: a ruler and a pencil for performing markup, an electrolybiz for drinking parts and knobs, a screwdriver, a screw for assembling a length of 30 millimeters, sandpaper or grinding machine To fulfill the finishing of the wet and planes of parts.
Product dimensions 600 × 400x200 millimeters. Inside at the top of the tank, two boxes are installed for small details and tools glued from more thin plywood. Two guides made in the form of a thickness of no more than three centimeters are attached to fix them along the side walls.
The process of making a drawer for tools is starting with the markup of parts of large and small plug-in boxes. If necessary, each wizard can vary the intended product size depending on the destination. The marked parts are muffled with an electrolybiz and are cleaned with grinding paper. Details of small boxes are collected using glue. For best connection The inner walls separating the space into separate sections can be made of shallow grooves in the thickness of the material. Clamps and other fixtures for clamp will help facilitate gluing work.
Build parts of a large drawer We carry out using self-tapping screws. To improve the quality of the assembly of the self-tapping screw, insert in advance drilled and splashed holes.
Do not forget to secure the two guides parallel to the box to which small containers will be relying.
For the manufacture of the handle, you can use the option proposed in the design indicated above, or install on self-drawing sufficient length Round rod. As a workpiece, a cutting cut for agricultural inventory can be approached for him, which is not difficult to purchase in any economic store.
Plywood does not apply to moisture-resistant materials. To protect the product when working on the street, you need to impregnate all the details of the box in any protective composition, Morilka or varnish.
Thus, after performing some simple operations, everyone can make for themselves comfortable device To transfer and storing tools. The use of such a box will greatly facilitate the process of performing repair and construction work Not only indoors, but also in the territory of the land.
Dear readers, comment on the article, ask questions, subscribe to new publications - We are interested in your opinion :)
In order not to spend time in search of instruments (hammer, screwdrivers, bodies), you should store them in one place. But what to do, if all the racks and cabinets in the house are crowded? Excellent solution This problem will become homemade drawer For tools. You do not require any special knowledge and skills. Production process itself portable box It will take no more than 3-4 hours.
How do you need to start?
The first thing you have to decide is with the size of the box. It all depends on the dimensions, quantity and total weight Tools that will be stored in it. As for the configuration, it does not matter. Ready product May have a square, rectangular and any other form. As you just wish.
Homemade is usually done from lumber or artificial wood (OSB-slabs, plywood sheet, Chipboard). Often are used various metals and high-strength plastic. It is difficult for beginners to work with these materials. Therefore, they prefer wood.
If you do not want to make rude mistakes and spend pastime, listen to the recommendations written below. Only in this case can be counting on a good result.
1. To make a convenient and reliable tool box with your own hands, you must first make a drawing of the design. This is done with the type, quantity and total weight of the tools.
2. Typically drawers are made from boards used earlier in other structures. Before re-use, they are purified by contaminants and dust residues. For light tools, it is better to take Faneru, and for heavy - strong boards.
3. on wooden surfaces Markings of all the details of the drawer are applied. Next, cut the blanks using a jigsaw or saw with small teeth.
4. Want to do open drawer For instruments with your own hands? Such a design involves the presence of a central handle. To install it, you must drill 2 deaf holes.
5. The assembly of parts is carried out with the help of screws and self-tapping screws. Securely lock the handle and proceed all the seams.
6. Make a toolbox with your own hands - only half of the case. We still need to give it an attractive look. You can cover the surface of the box with paint or special varnish.
Tools and materials
Very soon we will proceed to the practical part, but still prepare everything you need. So, for work we will need:
- drill;
- pVA glue;
- plywood (thickness 12 mm);
- pillet designed for a logs on a tree;
- a hammer;
- lobzik with a function of sawing at an angle of 45 degrees;
- varnish for wooden surfaces;
- drill;
- several bars 15x15 mm;
- clamps;
- small nails.
Make the tool box with your own hands: step-by-step instruction
What should we end up? Wooden design, where there will later be stored nippers, screwdrivers, hammer and other tools. The action plan is as follows:
Step # 1. For a start, take into the hands of Phaneru. We will use it for the manufacture of the side walls of the drawer. So that the ends are well docked each other, they need to cut a little, placing the jigsaw pylon at an angle of 45 degrees. A similar type of docking specialists are called "connection on the US".
Step # 2. Wash the ends with carpentry glue. If you failed to buy it anywhere, then use PVA.
Step number 3. Embed to the assembly of the whole design. For the details did not scatter, they must be fixed with scotch. Make sure the walls are connected smoothly. Now we wait until our billet dry.
Step No. 4. To the existing design you feed the rails that will keep the bottom of the box. Here you need to show accuracy, because nails are very small.
Step number 5. We make the bottom of the box, and then glue it to the raids. We use the same PVA.
Step number 6. For ease of carrying the box, we make a handle. We take a thin board. Electrolovka cut out the thinning on it. It is very important. Also remember to cut small rectangles from each corner of the handle. Their depth is equal to the thickness of plywood from which the sidewalls are made.
Step number 7. In the side walls, drill and remove cutouts under the handle. Make sure that nothing dangled. In the sidewalls, the handle and walls of the box should be the deaf hole to insert the waders.
Step number 8. Go to the assembly of the handle. All the joints of it with the sidewalls, as well as the sidewalls with the walls of the PVA well. Gradually assemble the details of the handle. Fix its position with the help of clamps.
Step number 9. All that we have left is a holder for a circulation, chisels and screwdrivers. We will use Phaneur. Cut out a strip from it, the width of which is 4-5 cm, and the length is equal internal size Long drawer wall. Then drill holes for the tools. The strip is coated with glue and attach to one of the walls using clamps. As soon as the glue is completely dry, you can proceed to finish processing Box surface. For this purpose, varnish or paint will fit.
Conclusion
Now you know about how to make a tool box yourself. There is nothing complicated here. The main thing is to clearly execute the instructions described above. Materials from which the design is created can be easily purchased in any construction store.
When you have a workshop or garage, then nothing stops us from acquiring all kinds of things: nuts, washers, screws, bolts, minor nails, brackets, and so on. But sooner or later the day comes and you begin to understand - little space. In fact, there is a lot of space, just to store you need to be able to correctly. Let's consider some storage options for all the little things in your workshop, garage or apartment.
Washers, selflessness, dowel - yes a lot of things will be thrown in the farm
Buy or make yourself box
A definite answer, as you guess, no. Someone just likes everything to do everything, and someone is lazy. Someone believes that several rubles, hryvnia, dollars or zloty for a simple boxes are cheap and, most importantly, without losing precious time. Well, and someone better tinker N-E Time for the workbench to make a unique box for trivia in its own way.
We have no right to advise you how to do in this situation. Choose yourself, buy or make yourself, spend money or spend time, enjoy manual labor or from a hike building stores. But one know for sure: the box, the box, the organizer or how you want to call - it should be the owner of several characteristics:
Purchased options
Organizers are now in the markets or in stores abound. It remains only to choose correctly. What trouble can be expected when buying and what places in such organizers are considered weak:
Homemade devices
It is possible to rank with those that are made completely with their own hands, and those that are designed to store other things, but you were purchased for hardware. These can be cans from coffee or storage boxes food products, maybe this is a plywood box or a converted kitchen hinged cabinet. Let's give a few recommendations:
Instead of imprisonment
Proper storage in the workshop is not only convenience for the owner, but also maintaining order, and it is sometimes even more important. Then the neighbor can demonstrate their favorite workplaceAnd the wife is empty that in the garage cleaner than in the house. Jokes jokes, but organizer, even by purchased, at least do it yourself - it is very necessary thingwhich should be in each wizard.