The ceiling in the toilet must be of high performance and resistant to aggressive environments, especially moisture. Not every finishing material is capable of combining beauty and durability in conditions of high humidity. Consider the most suitable options and features of their use in the sanitary room.
Requirements for finishing materials for the toilet
The toilet room has its own specifics - in addition to placing sanitary equipment in it, water supply and sewerage risers pass through it. If it is necessary to repair various pipes, it is necessary to proceed from the principle of the least damage to finishing materials. When choosing a ceiling finish in a toilet, you should be guided by the following principles:
- Resistant to moisture - the ceiling material should not be sensitive to condensation and not be a breeding ground for mold.
- Ceiling trim should not be an obstacle to access to pipes.
- Convenience and ease of installation of the material, which does not complicate the laying of electrical wires and ventilation ducts.
- Ease of maintenance - it is desirable that the surface of the ceiling could be cleaned by wiping with a damp sponge, avoiding complex and time-consuming manipulations.
- The material should correspond to the aesthetic ideas and be combined with the wall and floor decoration, fitting into the overall design idea.
- The ceiling construction should take up minimal space and not reduce the height of the room too much.
- Compliance with environmental standards is a powerful argument when choosing a finishing material.
The above requirements are of great practical importance.
In the event of emergencies such as flooding, the moisture-resistant ceiling finish will not need to be replaced, while other materials will have to be completely replaced.
With a small toilet room, it is preferable to decorate the upper part of the room in light colors.
Types of ceilings for the toilet
Among consumers, the following types of ceilings were most popular and highly rated in service:
- tension - not afraid of wet cleaning and does not absorb various particles, has sound insulating properties and is an environmentally friendly material;
- rack and pinion - it is made in two versions: made of aluminum and plastic, a special system of fastening the rails to a bar with teeth (bus) allows you to create seamless connections;
- suspended - durable, moisture resistant, affordable, can be made of various materials, easy to clean;
- from plastic panels - cheap, no connection points are visible, requires the installation of a ceiling plinth, the ceiling surface is ideal, high installation speed;
- gypsum plasterboard - is a type of suspended ceilings, made of moisture-resistant plasterboard, mounted using a metal frame, distinguished by ease of installation, low price, the ability to finish surfaces with complex relief.
Other types of ceiling finishes are not very widespread. Let's consider the above options and installation methods in more detail.
Stretch ceiling
The stretch ceiling in the toilet is made of polyester fabric pre-impregnated with an environmentally friendly material - polyurethane. Installation is carried out using an industrial hair dryer, which heats the material, which allows it to be better pulled. With the help of special fasteners pre-installed in the corners and around the perimeter of the room, the fabric is fixed. During the cooling process, the ceiling material contracts and stretches, forming a monolithic structure with a smooth surface.
The advantages of a stretch ceiling include the following qualities:
- easy care and convenient surface cleaning;
- takes up a small space in height (about 3 cm), sufficient only for masking communications;
- dismantling is not difficult;
- high strength characteristics allow it to withstand the full load of several cubic meters of water in case of emergency flooding from neighbors, which can then be drained through the hole for the luminaire.
It is better to entrust the installation of a stretch ceiling to professionals in order to avoid annoying mistakes and additional expenses. This type of coating is gaining popularity and is gradually replacing drywall as a finishing ceiling material.
Dropped ceilings
There are many ideas on how to decorate the ceiling in the toilet beautifully and practically. Most often, the choice of owners of apartments and private houses falls on suspended ceilings. And this is no coincidence. Since a suspended ceiling can be made from different materials and installed in different ways, the choice becomes simply huge. Consider the main varieties of this finishing method.
Rack ceiling
The design option, in which a rack ceiling is used, can be attributed to the budget. Even if professionals are involved in the installation, the final cost will still be low. The price is also influenced by the type of rails. If aluminum is chosen as the material, this will slightly increase the cost of materials, but also allow you to create an exceptionally beautiful and durable ceiling in the toilet.
Among the disadvantages of such materials are the following features:
- the height of the room decreases markedly;
- the color scheme does not differ in variety;
- panels with a pattern should be selected relative to each other.
The positive features of slatted ceilings are as follows:
- water resistance;
- high speed of installation (it can take several hours);
- one person is enough for work;
- in case of flooding, the ceiling does not have to be replaced;
- the ability to install a powerful lamp, due to the insensitivity of the battens to heat.
We can conclude that the slatted ceiling is a very practical and inexpensive solution, the main disadvantage of which is the lack of a wide range of products.
Ceiling made of plastic panels
A great solution for finishing the ceiling of the toilet room for little money. The cost of the panels is quite low, and their installation is not difficult. The installation can be done independently within 5-6 hours.
The ceiling made of plastic panels is not afraid of moisture and has a presentable appearance. To carry out the installation of this material, one worker is required, armed with a screwdriver and a hammer drill.
The disadvantages of this material are small:
- the surface of the panels will not be solid, seamless options are much more expensive;
- the pattern on the surface of the products has a longitudinal orientation and special geometry, therefore, it requires the selection of one panel to another;
- the material is quite fragile, so care must be taken when transporting.
The advantages of this finishing material include:
- resistance to moisture;
- ease of maintenance (cleaning the surface is not difficult and does not require special measures);
- the height of the room is reduced by no more than 5 cm;
- Many color options allow you to choose a solution that harmonizes with the walls and floor of the toilet.
Ceiling decoration with plastic panels is a suspended structure. When installing, there are two solutions for the design of pipes:
- Manufacturing of a special box for pipes and installation of panels on the remaining ceiling area with length adjustment.
- Making holes for pipes in panels and installing them over the entire ceiling area.
To decorate the room in an original and beautiful way, you can choose panels of the following types:
- Chameleons;
- 3-D panels;
- with a rough surface;
- glossy;
- mirrored;
- with embossed or embossed surface;
- matte panels.
PVC ceiling panels are a structure made of plates, between which special stiffeners are located. Insufficient strength and sensitivity to mechanical stress make this material brittle. However, these characteristics are somewhat improved by the use of strong and high-quality stiffeners.
Seamless PVC panels do not form gaps during installation, and panels resembling lining are classified as embossed. A neat and small seam in the varieties of products with rustication imitates the seams of reinforced concrete floors.
How is the installation of plastic panels for the ceiling
The entire installation process can be broken down into a sequence of such actions:
- Wooden bars with a cross section of 30 * 30 mm are nailed to the ceiling, having previously treated them with a wood preservative. For fasteners, anchors are used, the length of which is 70 mm. A distance of 40 or 50 cm is maintained between the bars.
- Wires are laid to the location of future lamps.
- The profiles "finish" and "start" are set, after which the distance between them is measured. The resulting value is the length of the panels to be installed.
- Using a hacksaw for metal, the panels are shortened to the desired length.
- A cut panel is placed in the side profile and advanced until it touches the starting profile and fixed with the latter.
- The frame and the panel are fastened by means of self-tapping screws, twisting from into the grooves.
- Each subsequent panel moves to the previous one by inserting it into the side profile, after which a spike is placed in the groove and snapped into place. In addition, products are fastened to the crate with self-tapping screws.
- The last panel is installed in the finishing profile from the side. It should be inserted with a groove or cut surface.
- For luminaires, holes are made with a drill using a crown attachment. In this case, it is important to first insert the light source, and only then install the panel.
- Depending on the decoration of the walls, the width of the panels should be selected. This means that when tiling walls, the width of the panel must match its width.
Waterproof plasterboard ceiling
The answer to the question of how to make a plasterboard ceiling in a toilet is not too different from the information on installing other types of suspended ceilings. The installation technology is as follows:
- Prepare the necessary materials: metal profile, putty, drill, screwdriver, level, screws.
- Treat the work surface with a fungicidal (antifungal) agent.
- Insulate electrical wires by placing them in corrugated pipes.
Installation sequence:
- The ceiling is marked out, the location of the fixtures and the main profiles is determined.
- Profiles (basic) are installed along the perimeter of the ceiling of the room using a level.
- The guide profiles are mounted in 60 cm increments.
- After the frame is installed, proceed to trim the moisture-resistant drywall sheets.
- Using self-tapping screws, the sheets are attached to the frame. It is convenient to use a screwdriver for these purposes.
- Holes are made in drywall through which the wires are brought out.
- Seams and places for installing screws, after which they begin to sand the surface.
- The acrylic primer will provide additional protection against moisture, therefore it is recommended to treat the ceiling with it after installation.
Before deciding to make a suspended ceiling from this material, you should take into account some of its disadvantages:
- It will not withstand flooding from upstairs neighbors.
- The height of the room will be significantly reduced.
Conclusion
Regardless of which ceiling was chosen from the above, it will eliminate the need to carry out costly and time-consuming work on leveling and preparing the surface for finishing. This is an important quality, especially considering the excellent performance and design characteristics of these materials. Contacting specialists will allow you to quickly and efficiently arrange the ceiling of the toilet without unnecessary nerves and labor costs. When installing such finishing materials on your own, it is recommended to follow the installation technology and purchase the necessary tools.
What is the best way to make the ceiling in the toilet
Let the toilet be a small room in the house, but it can also be made comfortable and beautiful. Many do not pay attention to this small room, but in vain, because it is she who reflects how neat the owners are and have good taste. A toilet is such a small room that it will not be difficult to make repairs in it and put it in order with your own hands. In order to inspire you to change, we suggest that you look at photos of already made repairs.
We will tell you how to finish the ceiling so that it looks beautiful and will serve for many years. With the help of the simplest recommendations, you can choose and make the perfect ceiling for yourself and your loved ones.
Choosing a ceiling option
Today you can choose materials for every taste - from cheap to expensive.
Here are the most popular materials chosen by home improvement store buyers for their washroom ceilings:
- plastic panels on the frame;
- suspended structure made of plasterboard;
- from ceiling tiles;
- rack and pinion design;
- painted or plastered ceiling;
- tension.
The choice depends only on your material capabilities and preferences for the design and appearance of this room. All possible options can be seen in the photos that we have collected. We hope, thanks to the ideas for them, your toilet and ceiling will become neat and beautiful. Hand-made work will be especially pleasant. Moreover, the amount of work is so small that it is unlikely to give you any trouble.
Rack
A metal frame is installed as a frame, on which a spike is attached to the groove of the rail. They can be varied in color and texture of the material, but silver, golden or mirror slats look most impressive due to the fact that they visually increase the space and make it not so boring.
Suspension
Suspended structures are often used as finishing, but during installation it is better to use materials with high moisture resistance, mainly plastic. For example, plastic panels or a sheet of plexiglass. This design will allow the use of spotlights and make this small and usually darkened room brighter.
Tension
It is possible to do this, but the cost of such work will be large, since the toilet has a small area, and the cost of such a small volume will be almost equal to the cost of work in a large room. But this method of finishing will last for many years and is as hygienic and of high quality as possible. Moreover, it can be of any color, with or without a pattern, matte or glossy.
Coloration
Of course, this traditional method is also possible. But the paint must be applied in several layers and a special paint marked "for wet rooms" must be chosen. The surface in this room is painted as well as in other rooms - it is primed, leveled, putty and painted.
You can see the photos of the ceilings that we talked about at the link. There you will also see everything you need to improve the room with your own hands.
Ceiling tiles
A very simple finishing option for installation and fits perfectly into the toilet. At the same time, there are many different textures, colors and patterns. Ceiling tiles will work even if you don't want to waste the effort of leveling the ceiling. It can be glued even on a non-ideal surface, the tiles will cover all irregularities and visually create the effect of a flat surface.
It is very easy to install and with the help of it you can refresh the repair more often. It is the most inexpensive finishing material. Today, seamless tiles have appeared; during installation, the seams can be made almost invisible, creating the illusion of a monolithic surface. True, you need to remember that with the existing differences in height, especially in old houses, it is better to abandon this method of finishing, since the absence of seams will further emphasize all the irregularities.
There are a few more tricks that will help make this room harmonious. For example, if you paint the ceiling in a dark color, then with high ceilings, the room will not seem like a well. And if you choose mirrored slats or the glossy surface of the tensile structure as a finish, then even the lowest room will increase.
So, making repairs with your own hands in the toilet is not difficult and not expensive, so it makes no sense to postpone this undertaking for a long time. Starting next weekend, your toilet will soon sparkle clean and fresh! And you will be happy with yourself, and the family - with you.
More information
The toilet is a specific place in all respects, and in terms of use, and in size, and in the environment. Often, when carrying out repairs in a house, sufficient attention is not paid to this room. But it is worth understanding that if you undertook to decorate a house, then you need to do this completely, nothing can be an exception. Moreover, the toilet is a small room, so repairs, including finishing the ceiling, will not require much time and money.
The features of this room and the design options for its ceiling are described below. The most popular finishes are provided with step-by-step instructions.
Toilet ceiling requirements
The main distinguishing feature of the toilet is the presence of sewer and water pipes, the toilet itself, which is obvious. Also, sometimes there are hot and cold water switches, meters and, if we are talking about a private house, a heating boiler. In this regard, the following requirements are imposed on the decoration of the toilet, including the ceiling.
Another feature of the toilet is its extremely small footprint. For this reason, specific requirements are imposed on the ceiling finish.
The next question to be considered is what colors and in what situations are used for the ceiling decoration of the toilet.
Colour
Before choosing the color scheme for finishing the toilet, determine the area of the room and how the height of the ceilings relates to the length and width.
If the room has a sufficient area and the ceilings seem relatively low, then they need to be visually "raised". For this, light shades of blue, pink, green and beige are used. The classic white color is also suitable for this. Silver or light metallic shades will help enhance the effect. An alternative option for visually "raising" ceilings can be a mirror finish using panels or PVC stretch fabric.
Prices for plastic ceiling panels
plastic ceiling panels
A black stretch ceiling is not the best option for a toilet
And in a situation where the length and width of the toilet are very small and even the standard 2.5 meters seem extremely high for ceilings, it is undesirable to use light colors - the room will become uncomfortable, you, your household and guests will feel like in a well here. Therefore, use dark colors in moderation - blue, purple, dark gray. In some situations, golden is acceptable.
Important! The location of the lamps in the toilet should be chosen based on the same considerations - if the ceiling seems low, then place the lamps at the top. In the opposite situation, the luminaires are placed on the walls.
Another finishing rule to remember is to avoid the uniformity of the walls and ceiling, the result will be a very uncomfortable room, more like a prison cell.
Whitewash
Let's start with the simplest finishing option - whitewashing. The main advantage of this option is its low cost, simplicity and speed of work. So, you can whitewash the ceiling in less than 30-60 minutes.
But these advantages turn out to be disadvantages. When using whitewash, you can forget about moisture resistance - the coating gets wet and slightly swells. And the old finish even peels off from contact with water. But in this case, the problem can be identified immediately and action can be taken. And again - not a problem.
Before starting work, the concrete floor must be prepared. Since the area of the room is small, the process does not require much time and effort.
Step 1. It is determined using the level of the difference in the height of the ceiling in the toilet.
Step 2. In a bucket, using a drill or a perforator with a mixer attachment, the putty solution is kneaded.
Whitewash prices
Types of Knauf putties
Step 3. Cracks and defects in the ceiling are repaired with a small spatula.
Step 4. The solution is applied to the entire surface of the ceiling with a sufficiently thick layer and leveled.
Step 5. The applied putty should dry within 24 hours.
Step 6. The next day, it is sanded with an emery cloth. Grouting should be done in undulating movements.
Important! Use lime wash for the toilet. The chalk-based composition will not last long enough.
The prepared solution is poured into a paint tray, also called a ditch, and applied with a roller to the ceiling surface. Make sure that the whitewash is applied evenly. The layers applied with a roller are overlapped by 5-15 centimeters so that there are no untreated areas left.
If the whitewash has partially crumbled over time or the finish layer has been broken by contact with water, then you can update the coating, since this does not require much time.
Putty prices
putty
Dye
This finish has similar advantages to whitewashing - the relative cheapness, speed and ease of work. In addition, the paint has a variety in the choice of colors, which will make the ceiling in the toilet beautiful. For finishing, choose waterproof grades - oil, acrylic, latex or silicone compounds. Some types of water-based paints are also suitable, but be careful when choosing - only waterproof formulations.
Table. Popular paint brands suitable for toilet ceilings.
| Name | Manufacturer | Type of | Peculiarities | Consumption - m2 per liter of paint |
|---|---|---|---|---|
| SNIEZKA KUCHNIA-LAZIENKA | SNIEZKA | Water-based | Includes antiseptic, moisture resistant, biostatic | 12 |
| Effekt Facade Silikontop | Effekt | Water-dispersive with the addition of silicone | Water repellent | 5 |
| TICIANA Т100601А | TICIANA | Acrylic | Light and water resistant, includes an antiseptic | 10 |
The application process is the same as for whitewashing.
- The concrete slab in the toilet is putty. Detailed instructions are presented above, in the section about whitewashing.
- The paint is unpacked and poured into a paint bath.
- The first layer is applied using a roller. There should be an overlap of 50-100 millimeters between the stripes.
- Two or three more layers are applied in the same way. Make sure there are no unpainted areas. Brushes should be used where sewer and water pipes are connected to the ceiling.
Important! When working with some types of paints, for example, with oil paints, use a respirator mask - prolonged inhalation of vapors leads to feeling unwell and headaches.
Another option for finishing the ceiling in the toilet is various types of tiles. Their overall advantage is that they create an attractive exterior coating that eliminates small differences in height and unevenness in the concrete floor, but, unlike suspended and tension structures, tiles do not lower the ceilings in the room.
Ceiling paint prices
ceiling paint
When choosing such a finish, attention should be paid not only to the quality of the material, its color and texture, but also to the size. Small tiles will create an effect that visually expands the length and width of the toilet.
The following types of tiles are used as finishes:
- foam;
- polyvinyl chloride;
- cork.
Foam ceiling tiles stand out for their extremely low price - only whitewashing can be cheaper. It is not difficult to glue the tile to the ceiling, but at the same time it changes color over time. In addition, during the installation process, be very careful not to break the thin and fragile foam panels.
The process is as follows.
Step 1. The concrete floor is covered with a deep penetration primer - this improves adhesion to the adhesive, and the tiles hold better and longer. Allow the primer to dry.
Step 4. Glue is applied to the foam panel - a few drops in the center and a strip along the perimeter of the tile.
Step 5. The tile is applied to the ceiling, slightly pressed (but not too hard, so as not to damage the material), after which you need to wait a while for the adhesion to establish.
Step 6. Until the glue has set, the tile is carefully leveled. Remains of glue are removed with a narrow spatula.
Step 7. The previous steps are repeated and the rest of the tiles are laid in the same way. Joint gaps should be kept to a minimum. In the future, they can be treated with silicone sealant.
Advice! The finish can be completed with a skirting board.
PVC tiles are more expensive than foam tiles, but they are more durable. In addition, this finish is waterproof. When buying a PVC tile, carefully monitor its quality - the finish made in violation of the technological process will deform or fall off over time. The installation process is the same as for foam tiles.
Another alternative to foam tiles is cork panels. But they have their own characteristics. Firstly, the color of the panels is not suitable for toilets with low ceilings. Secondly, their cost is significantly higher than that of analogues made of polyvinyl chloride or expanded polystyrene. But in addition to its attractive appearance, cork tiles have sound insulating properties.
Plastic panels
Now let's move on to the description of finishing for the ceiling in the toilet using suspended structures. They completely hide all the imperfections and irregularities of the concrete or wooden floor, but at the same time hide from 30 to 50 millimeters or more from the ceiling height. Therefore, they should not be used in rooms with very low ceilings.
Let's start with plastic panels. This is an affordable and very diverse finishing material with the following advantages.
- Ease of maintenance - dust, dirt and condensation accumulated on the ceiling can be easily washed off with a cloth or a sponge dipped in soapy water.
- Ease of installation - the process is available even to those who are not qualified specialists and do not have extensive experience in repair work.
- Variety - There are many types of plastic panels. Some are stylized as wooden lining, there are also panels with a mirrored surface or with a surface imitating stone. Here you will definitely find the option that is right for you.
- Moisture resistance - plastic is not afraid of condensation. And with proper installation, a solid suspension structure will be sufficiently airtight and will withstand a small flood from neighbors.
- Heat and sound insulation. The plastic itself and the air gap between it and the overlap serve as a barrier in the way of sounds from above or warm air going upwards.
As for the disadvantages of plastic panels, such products can be damaged when struck by sharp objects, and when they burn, they emit smoke containing harmful substances.
Now let's look at how to mount such a structure.
Step 1. The surface is prepared - the old finish is removed from it, if any, the seams and cracks in the floor are closed.
Step 2. A crate is installed on which the panels will be directly mounted. It is arranged from a wooden bar with a section of 3 by 3 centimeters. The interval between the elements of the frame is from 30 centimeters to half a meter. Fastening to the ceiling is carried out using self-tapping screws with dowels.
Step 3. If you plan to install lamps, wiring is laid and fasteners are installed under the lamp. A hole is made in the panel, which should be in this place, with a drill with a crown attachment exactly in accordance with the diameter of the future lamp.
Drywall prices
drywall
Making a hole for a lamp
Step 4. Start, finish and side profiles are installed.
Step 5. The first panel is wound into the side profile, moves to the starting one and is fixed there on the crate with the help of small screws screwed into the bar adjacent to the bars. The outer surface of the panel must not be drilled or damaged in any other way.
Cutting PVC panel 5 mm shorter
Installing the first panel, step 1
Installing the first panel, step 2
Step 6. Similarly, the next panel is wound up and carefully mated to the first tongue-and-groove connection. The operation is repeated with the fasteners.
Step 7. The rest of the panels are laid in the above way.
Step 8. The finish panel is trimmed so that it can be inserted into the profiles. This completes the process of laying the plastic panels.
Installing the last panel, step 1
Installing the last panel, step 2
In a similar way, a ceiling made of natural lining or panel-cassettes is installed, the design of the lathing can only differ.
Stretch ceiling and plasterboard ceiling
The remaining options for suspended structures are a plasterboard ceiling and a stretch canvas. But using them for the toilet is a matter of personal preference, and very controversial. Such a finish is perfect for large rooms, but in small rooms, multi-level structures may not look entirely appropriate.
Another controversial issue of such ceilings is access to communications. To repair or replace the sewer and water pipes in the toilet, partial or complete dismantling of the suspended structures will be required.
If you decide to use one of these designs, then remember the following nuances.
- Choose only moisture resistant drywall grades. Other options, with constant contact with condensate, will quickly become unusable.
- The profile for suspended structures must be galvanized - without protection against corrosion, it will lose its strength over several years and at one "fine" moment the entire ceiling may simply collapse.
- A stretch ceiling with a PVC sheet is extremely convenient when flooding from above - PVC can withstand up to 80-100 liters of water per square meter.
- Use baguettes and a canvas with harpoon fasteners - so dismantling during pipe repairs will be carried out as quickly as possible and without damage.
It makes sense to use a plasterboard or stretch ceiling in a newly built building, especially made of wood, since such structures (we are talking about ceilings) in the vast majority of cases do not deform and do not lose their attractiveness during shrinkage.
Stretch ceiling prices
stretch ceiling
Finally, it should be said that regardless of the chosen option for the ceiling finish, before performing it, decide the issue with waterproofing - several layers of special film on good fasteners will significantly reduce the damage in case of possible leakage from above.
Video - False ceiling in the toilet. Part 1
Video - False ceiling in the toilet. Part 2
Video - False ceiling in the toilet. Part 3
Video - False ceiling in the toilet. Part 4
Video - False ceiling in the toilet. Part 5
Ceilings in washrooms, as well as in bathrooms, are subject to increased performance requirements. And this is not surprising - the humidity in these rooms is often high, the space is limited, and at the same time, you want to get something beautiful and practical.
To facilitate the choice, consider the most popular options for how the ceiling in the toilet is finished, in the photos attached to the description of the option.
Variants
There are many ways to decorate the ceiling in this room. But, the most popular are only four main ones:
- Tension
The rest of the design types are less popular, although there are quite interesting solutions among them.
Each of the above methods deserves a separate close examination, which we will do next.
Plasterboard
Probably the most common way to give a nice look to the upper part of the room. Its advantages are low cost, ease of construction and the ability to perform all installation operations with your own hands.
If you get tired of the look, you can repaint it, or, if desired, glue it over with new wallpaper or polyurethane tiles. There are a lot of options for how you can arrange drywall. And almost all of them can be applied.
Another positive quality that is inherent in all suspended structures is the ability to hide almost any defects in the interfloor slab.
Unfortunately, such structures also have a common disadvantage associated with the fact that during the construction of a suspended base, the height of the room inevitably decreases.
Stretch films
An increasingly popular finishing method. At a cost, it will come out slightly more expensive than a high-quality construction using gypsum sheets. And according to its main characteristics, it will be much more attractive.
It has all the advantages of suspended structures, but at the same time, it is practically devoid of their main drawback - the height of the room in which the tension cover is installed can be reduced quite a bit - from 3 centimeters. It's almost imperceptible.
At the same time, such a ceiling in the toilet looks very good - take a look at the photo. It can be washed, it is not afraid of moisture, and this is one of the most important advantages of stretch coatings.
With a flood from the upstairs neighbors, you don't have to change it. It will be enough just to drain the water and wait for the film to stretch again, and this will only take a couple of hours.
The main drawback is the inability to make the film itself on our own. It is also better to entrust it to specialists to pull it on, but with all this, the stretch coating is an increasingly popular type of finish, gradually replacing drywall.
Structures from MDF or plastic panels
An excellent option for a budget solution to the problem, with finishing the upper part of the toilet rooms. The cost of plastic panels is very low, and some types of MDF finishes very well copy wood or stone surfaces.
MDF parts, of course, will be more expensive, but, with plastic, they are united by the method of installation, and the simplicity of this process.
Everything can be done in half a day, and at the same time, there is no need to call the construction team or installers. A design from such elements can be perfectly done on your own, there would be tools at hand.
If we talk about plastic panels, then they are the best fit for toilet rooms - they are not afraid of moisture, they look quite beautiful, and the cost is very low.
MDF planks are no longer so practical - moisture can damage them, but there are types covered with protective compounds and films that resist water well.
For the installation of the entire structure, one person will be enough who can handle a hammer drill and a screwdriver. The finishing will take no more than one half of the day.
The disadvantages are not the most serious - from such parts, it is very difficult to obtain a solid surface. There are types of surfaces that are called "seamless", but their cost is quite high.
Another of the peculiar drawbacks of all panel coverings is the geometry and directionality of the pattern, along the arrangement of the parts.
Rack
This design method can also be attributed to a fairly budgetary one. The cost of the entire built ceiling will be quite low. Of course, a lot depends on the type of rails chosen, but still, their cost will not hit the repair budget too much.
The disadvantages are very similar to those of the panel ones - the directionality of the pattern, a decrease in the height of the room, and a poor palette of colors.
Of the advantages - they are not afraid of water, one person can mount it, and it will take very little time for installation.
In the event of a flood from the neighbors from above, the entire coating does not have to be changed - the water does not affect it in any way. Also, you can not be afraid to choose a lamp that is too powerful - heating to such surfaces is also not terrible.
The solution is very practical, although it has a limited number of design options.
Conclusion
There are a lot of ways to decorate the ceiling in the toilet, and most of them could be seen in the attached photos.
Which one to choose is up to you, but you need to do it based on the size and height of your room. Conformity in general, the rest of the design is a very important point.
Plastic panels are becoming more and more popular in the construction market today. This is no coincidence, because if you install such material in a toilet or bathroom, then the room will look aesthetically pleasing and neat. The panels are easy to care for, they weigh a little. Take a closer look at this finishing option when renovating your bathroom or toilet. The panel is attached to the frame with a stapler or self-tapping screws. Spotlights are built into the ceiling of this material.
Pros of PVC
A plastic ceiling is the most correct solution, as it has advantages over other materials:
- not afraid of moisture;
- withstands temperature drops in the room;
- does not absorb moisture;
- does not swell under the influence of moisture;
- at elevated temperatures does not increase in size;
- hygienic, does not allow the development of mold and mildew;
- thanks to the excellent reflectivity of the panels, the toilet becomes lighter, and because of this, the consumption of electrical energy is saved;
- electric wires are removed under the panels, which go to the lighting fixtures;
- the surface of the walls and ceiling becomes even.
The plastic panel is a long strip with an average width of 25–30 cm. The end is cut off, and there are locks on the sides, which will connect the elements during installation.
In the photo - PVC cross-section. There are stiffeners inside. Therefore, the material is lightweight, but at the same time durable.
Panel profiles
This material is intended for decoration when covering the ceiling or walls in a toilet or in another room using PVC panels. It is divided into the following types.
- Start profile. Covers the trimmed ends of the panel. Fastened around the perimeter of the room.
- Profile F1 covers the cut end at the outside corner when you want to change to another plane. It is used in the event that one of the walls is sheathed, and the one that is around the corner is not.
- Profile H (connecting). Serves to lengthen the strip if it is not enough.
- The outer and inner corner is designed to cover the ends in the corresponding corners.
- The ceiling plinth is designed in the same way as the starter profile, but with a more attractive look.
Pros and cons of PVC panel mounting
Each of the materials intended for cladding has its own advantages over others. PVC panel also has many positive properties:
- evens out the curvature of walls and ceilings in rooms, without the need to dismantle old coatings;
- installation is quick and easy;
- heat and sound insulation is laid behind the panels;
- no dust and no wet process;
- affordable price.
Disadvantages of plastic:
- it will not be possible to complete a multi-level ceiling;
- some panels look "cheap";
- the connection between the panels is visible.
Therefore, when planning repairs in a toilet or bathroom, it is advisable to take a closer look at the quality of the material. After all, the better it is, the more expensive it is, and, accordingly, the appearance is more attractive. For this reason, the PVC panel is limited in its use. It happens that when installing a lighting fixture, the plastic ceiling shines through.
Important! Before you buy plastic material, weigh all the pros and cons so you don't regret it later.
Calculation of material for installation
First, calculate the area of the ceiling in the toilet. Then divide the resulting figure by the total area of one PVC panel. Add 15% to the resulting number for trimming and round to the nearest whole number.
To calculate the amount of metal profile, follow the diagram of the ceiling in the toilet, observing the scale. Determine where the parallel lines will go along the ceiling. They are necessary for fixing the profile. The interval between parallel stripes is at least 50 centimeters. Based on these calculations, it is easy to calculate the required amount of material.
For fixing along the perimeter of the surface, you need to purchase the UD strip, and for the guides - CD. To attach PVC strips to the profile, you will need self-tapping screws with wide caps.
A plastic skirting board will help to complete the work on finishing the ceiling. To calculate its amount, measure the perimeter of the ceiling, divide this number by three, and then round it up.
Installation of a frame for PVC panels
Installation of the frame in the toilet is carried out using the aforementioned profiles: CD and UD. Wooden slats are also used, but much less often, because the wood is exposed to moisture, especially in a room such as a bathroom or toilet. The tree is prone to decay and will last less.
How to install the frame correctly?
- Marking is carried out using a level. In a large room, it is better to use a long level, and in a small toilet, a simple rack and pinion tool will suffice. Marks are made for the guide profile. The location of suspended PVC panels on the ceiling depends on them.
- The profile, if necessary, is cut to the size of the room (the length of the profile is 3 meters). It is drilled in 50-60 centimeters increments. After that, the guide profile is applied to the wall, the holes are marked on it, the dowels are drilled and inserted. Each time, check the horizontal level.
- The frame is stiffened by the ceiling profile. The mount for it is chosen, taking into account the distance to the base: if the gap is insignificant, then a U-shaped suspension can be used. If it is large, then it is better to take fast-hangers with knitting needles. Sometimes specialists make special “boots” for the UD frame. To do this, cut the metal with the letter "G" and attach it with the smaller side to the ceiling, and the larger side to the bearing profile.
- The hangers are fastened to screws, checking by level. The step between the profiles is 50 centimeters, they are placed perpendicular to the PVC panels.
Definition of quality
When purchasing, inspect the panels carefully. High-quality products are even, the pattern is evenly distributed. The front side is smooth and flat. Distortion and curvature of lines are not allowed.
Important! Count the number of stiffeners inside the panel. The more there are, the stronger the structure.
The thickness of the stiffeners and the outer walls of the plastic plays a role. Take two strips and try to connect them. The main thing is not the quality of the connection, but the ease of docking. There should not be a large gap between the stripes. To determine the strength of the material, take the strip and squeeze hard, then inspect the surface. If it is not deformed or cracked, this is a quality material. But slight deformation is acceptable.
Check the strip for bending. To do this, bend and unbend it 3-4 times. If after this procedure the material has survived, then you can work with it. Poor quality plastic will deteriorate during installation.
What is required to work with plastic?
The color scheme plays an important role. Today this is not a problem, and everyone will find an interesting option for themselves.
Toilet cladding is impossible without raw materials and tools. You will need the following:
- Sharp knife to reduce the size of the plastic strips. A kitchen knife will ruin the material and cut unevenly.
- Self-tapping screws for fastening strips.
- Wooden beams for the frame with a cross section of 3 x 10 cm or metal parts described above.
- If you are planning to fix the panels directly to the wall, you will need liquid nails or polyurethane foam.
- Any renovation will not be complete without a tape measure.
- Building level for mounting the frame.
- Decorative skirting board, which is attached to the wall.
- Profile corners.
Mount selection
Before starting work, determine how you are going to fix the panels: with mounting foam or using a frame.
The first option involves the purchase of foam cylinders. When purchasing a product, pay attention to the expiration date. Fresh foam will yield more. If the toilet is spacious and there are brick walls, it is not necessary to install a frame. It is allowed to fix PVC panels with liquid nails. This job is not difficult, but it takes patience.
How to cut plastic material?
This process is straightforward. Take the stripes and lay them on the base with the wrong side. Then an incision is made with a sharp knife to form a line. They break the plastic along it and again cut it off completely along the marked line with a knife.
Preparation for work
Repair of the toilet and preparation for lining begins with cleaning: sockets, lighting devices, hoses, pipes are removed from the walls.
If the frame method of fastening is chosen, it is more rational to use galvanized parts. If you took a wooden block, treat it with an antiseptic.
First, the frame is mounted, and then the strips are installed, where the panels are inserted. Ceiling work in the toilet starts from the corner. One edge of the PVC strip is inserted into the profile, and then the other side is attached to the screws
The next strip is easier to insert, push it until it clicks. And again, the other side is attached with self-tapping screws. Then the plinth and decorative strips are installed. With their help, you can disguise defects and technological gaps. They are attached with glue, as these are purely decorative details.
Almost everyone will be able to repair a toilet using PVC panels. The process is shown in detail in the video: