Many homemade craftsmen dreamest of self-cutting sawn timber. This is simple, but without suitable equipment - practically impossible. So why not adapt to this manual circular saw and do not collect your own table with the possibility of longitudinal and transverse cut?
In four corners of the shoe, make one hole with a diameter of 10 mm. Drilling places arbitrary. Install the saw disc in the groove of the table top and align the shoe on the markup. Follow the centers of the manufactured holes on the plywood and transfer them to the opposite direction by a thin drill.
If there is not enough space in the support shoe to drill such large holes, use a two steel plates with a welded studs of 6 mm, attach them to the base of the saw can be wrapped with wrapped stagnas. In this case, remove the saw for handmade And bring it back to the place without additional adjustment will be the case of five minutes. Plates, in turn, have one large opening, for reliable installation and initial saw position adjustment.
For fastening saws to the table top, you need to use M8 leverage bolts with a secret conical head. Under them S. front face An 8 mm hole is drilled and a cenchka is made under a hat, which in an uncomfortable state should perform above the surface of no more than 1 mm. On the reverse side, the bolts pass into the holes of the support shoe (or steel plates) and are delayed under a wide and spring washer or a nut with plastic grover.
If the fitting was successful, the worktop must be fixed to the box. In four corners of the plywood stove, you need to drill one such a hole as for fastening the saw. The distance from the edges is half the side of the Brawn used plus the thickness of the box wall, in our case it is 30 mm. In the center of each bar, a 10 mm hole is thrown in, the steel bag M8X18 mm is screwed into the inside.
When the table top is fixed, turn the table on the side to have access to the disk and the fastening places of the saw. I remove the protective casing during the time, apply the saw disk on the longitudinal axis of the table using the rail and the rich. After adjusting the disk, tighten the mount nuts well. Using a ruler or level attached to the disk, apply a label on the edges of the table and spend the line plane line. Spend the line several times with a sequel, leaving a shallow furrow, such a markup is definitely not erased after a long service.
Start button and electrician
The regular power button must be stunned, and if there is no such possibility - to push the clothespin or harness. Instead of a button on the handle, a small power grid is used, laid inside the box.
On the external front side of the box, set the dual button "Start / Stop" with fixation. Its normally open contact is connected to the power cable break. Wire ends are connected to plug socketScreen S. inner.
After the saw is connected and verified in the work, it is necessary to stretch on the air intake lattice, threefolded chipping stockings.
Cross-rendering
Conditioning parts is convenient to conduct in the presence of a thrust beam, which moves along the guides along the section line. You can make such an ordinary 9 mm plywood.
It will take only a few pavements:
- 150x250 mm 2 pcs.
- 100x820 mm 2 pcs.
- 150x820 mm 1 pc.
- 142x300 mm 1 pc.
As before, plywood is preferred on accurate equipment. Three long plate need to be collected in the form of a sewller 150 mm wide and shelves per 100 mm. Since the hats of self-tapping screws will be addressed to the tabletop, they need to pre-reassure the paneur and draw fasteners, and after processing the traces of sandpaper. It is more reliable instead of self-samples to use confirmates.
The 150x250 mm boards are screwed like a chapeller plugs, free ends are guided down. The remaining strap is screwed between the shelves exactly in the center. If this beam put on the table, the side boards will be devastated on the sides of the box with a gap of about 10 mm on each side.
Use furniture guides full extension on the ball bearings. First fasten them to the beam, and then try on and screw to the body. Holes for fasteners are oblong, use them to adjust the beam: it should slide over the table top with a very small gap and at right angles to the plane of the cut. Swipe once with a saw on to make an incision at the bottom. For fast removal And the installations of the beam are recommended to deduct plastic locks in guides in advance.
Adjustable focus for longitudinal sawmills
Freight forest is much easier in the presence of a longitudinal stop. You can make it from ordinary aluminum cornice or other easy profile With perfectly smooth edge and rigids. It takes a segment along the length of the table, that is, 800 mm.
In 150 cm from the edges, make two holes for 8 mm and insert them on the M8 bolt, orienting threads down. Screw the nut without the washer and tighten tightly. At the same distance from the edges of the table, spend two lines. At the intersection of them with the axial line of the countertops, drill holes 12 mm. Another opening is drilled on the same lines with an indentation of 30 cm. Using a mill or jigsaw, make two thin slots, it is advisable to make a cut as much as possible.
The profile of the stop is inserted by bolts into these slots, after adjusting it can be filled with lambs with a wide washer from the inside. If the width of the cutting you need to change frequently, supply the table door loops For easy opening. To quickly perform adjustment of the stop, fasten the ribbon ribbon trimming on the ends.
Circular saws applied to cut wood along the array. Its cutting base is a disk-shaped plane having a toothed outer edge. Such saws are not only manual, but fixed on the table. How to do universal table For circular, so that you can install this cutting tool? Below are offered several ways to make the table for circular saw do it yourself.
Table for circular saws with your own hands
How to make a table for the circular from LDSP? To make such a table under the circular, are necessary:
- laminated plywood sheet 9-11 mm thick (800x800 mm);
- 4 sheets LDSP thickness 16 mm (400x784 mm);
- several bars of 40x40 mm;
- several bolts and screws;
- aluminum cornice.
On this table you can fix any manual disk Saw. With a big disc. Drawings of the table for circular to this type can be easily found on the Internet.
Such a saw is made in several stages:
Circular saw guides are made from a bar or aluminum cornice.
The second version of the table for the circular. Photo of manufacturing technology
The table-drank is done from the boards, as the most affordable material, often. For the manufacture of this table, you will need:
- plywood sheet (thickness 20 mm and above);
- 50 mM boards;
- bar 50 by 50 mm;
- several screws;
- wooden glue;
- one of the types of wood varnish.
From the plywood sheet, the blank with a hole is cut down - a tabletop, which will be placed. When laying holes, focus on the sole sole soles. The ribs are made from the boards, which will be attached to the tabletop self-drawing. In the process of fastening the board, it is tightened with clamps. On the front rib of stiffness later, a start button is installed. For the manufacture of legs, the boards are about a meter long. They are fixed outside to the ribs of stiffness bolts.
Video Circular Table of Manual Circular Saw
Examples of finished tables for circular saw
The table for the circular is not always appropriate to do with your own hands. It can be too bulky and clumsy, it is difficult to adapt to high-precision sawd wood. Therefore, if not sorry to spend some amount financial means, it is better to purchase factory-made tables. They are made of durable and convenient materials when working, safe when turned on electric currentAnd also have a factory warranty in case of breakdown.
At the circular saw JET JBTS-10 from each side there is a retractable table, an increase in area suitable for work. Thanks to the belt wire, it is cut with silent, as well as the deadlines for the operation of the electric motor. The presence of an eccentric clamp excludes the displacement of the machine during operation, which makes it use convenient in any conditions.
Using desktop saw EPN-1100 caliber exists the ability to saw wooden materials in the longitudinal and transverse direction, as well as under different angles. The level of inclination of the saw can be selected and fixed.
IN sifting machine Enkor Corvette-10m 90101 applied side and parallel emphasisthat, which greatly facilitates the work. The saw blade when sawing can be tilted at an angle to forty-five degrees. An industrial vacuum cleaner can be connected to the machine, removing wood dust. In this case, the device is characterized by ease and small dimensions.
The use of the stationary circular saw EINHELL TC (TH) -TS 820 allows you to work with sawn timber mass production. It is a suitable tool when processing not only wooden, but also fibrolite blanks. The design of this model provides a hole in which devices producing wet and dry cleaning machine are connected. At the same time, the equipment is so compact that it can be installed on any workbench.
Offer's contract
An individual entrepreneur Klimov Alexander Nikolaevich, acting on the basis of a certificate of state registration physical face as individual entrepreneur, hereinafter referred to as the Seller publishes this public offer of digital goods presented on the Seller's website
1. GENERAL PROVISIONS. Subject contract
1.1. In accordance with Article 437 of the Civil Code Russian Federation (Civil Code of the Russian Federation) This document is a public offer, and in the case of the conditions set out below individualThe acceptance of the acceptance of this offer pays for goods and / or services in accordance with the terms of this Agreement. In accordance with paragraph 3 of Article 438 of the Civil Code of the Russian Federation, the payment of goods by the Buyer is an acceptance of the offer, which is considered to be equivalent to the conclusion of the contract under the conditions set out in this offer.
1.2. Based on the foregoing, carefully read the text of the Public Offer, and if you do not agree with any item of this offer, you are invited to refuse to buy goods and / or services provided by the Seller.
1.3. In this offer, if the context does not require the other, the following terms have the following values:
Acceptance - full adoption by the buyer of the terms of the contract;
Offer - the public offer of the seller, addressed to any physical person (citizen), to conclude a sales contract with him (hereinafter - "Treaty") on the existing conditions contained in the contract.
Buyer - site visitor - an individual who has entered into an agreement with the seller under the conditions contained in the contract and making the purchase of digital product (s) and / or services.
The parties are the seller and the buyer here together.
Website - the Internet Placed area with the domain name "Site", which is an online store containing the range of goods and services of the seller.
Digital product - a virtual product, which is the subject of this Agreement and having the following types:
a) Ready digital products - laid out for sale digital products that have completed appearance and ready-to-use.
b) Courses - training programs using a distance learning system.
Delivery - delivery by the seller of digital goods presented on the site by means of electronic communication channels to the email box, whose address is specified by the buyer in the order;
Account is a virtual "Cabinet" of the buyer, in which the registered user sees its personal data.
Registration is the process of introducing personal data by the buyer in a special form on the site when forming an order (surname, name, email address).
Order - separate positions from the range of digital products specified by the Buyer when making an application for digital goods.
2. Subject of the contract
2.1. The seller sells digital products in accordance with the current price list, published by the seller's online store on the site site, and the buyer makes payment and accepts the goods in accordance with the terms of this Agreement.
2.2. The seller supplies digital products in an exceptionally virtual form by e-mail and does not send printed goods by mail.
2.3. This Agreement is the official document of the Seller.
3. Registration of the order
3.1. The order of goods is carried out by the buyer by referring to the proper completed form in the process of payment. All column columns must be filled. In the absence of the necessary information that allows you to identify the buyer and send it a product, the seller will not be adopted.
3.2. When placing an order, the buyer undertakes to provide the following information about himself:
last name and first name,
E-mail address.
3.3. The buyer provides its consent to the processing by the seller of the buyer's personal data using or without the use of automation tools. This buyer's consent extends to his name, name and other information related to his personality and indicated when placing an order. Consent is provided to carry out any actions on personal data that is necessary for the proper execution of this Agreement, including without limitation: collecting, systematization, accumulation, storage, refinement, use, distribution, blocking and destruction, as well as the implementation of any other actions with personal data In accordance with the current legislation of the Russian Federation.
3.4. Payment by the buyer made on the order site means the consent of the buyer with the terms of this Agreement. The day of payment of the order is the date of concluding a contract purchase Between the seller and the buyer.
3.5. In the event of a buyer questions regarding the goods, before registration of the order, he needs to seek the seller's advice on the electronic mailbox. [Email Protected]website or through the feedback form posted on the site.
4. Conditions and deadlines for the delivery of digital goods
4.1. Delivery to the buyer of the paid product is carried out by sending an email with reference to receiving a digital product at an email address that the buyer indicated during the registration process. The deadline for sending a letter - 8 hours from the date of payment.
4.2. The seller delivers goods on the basis of the order made by the buyer.
4.4. The goods are considered received by the buyer, and the responsibility of the seller for the delivery of goods executed from the moment of fixing the operation to send goods by electronic communication channels to the electronic mailbox of the buyer in the automated electronic seller's electronic system.
4.5. In case of non-receipt of the goods by the Buyer in the period specified in clause 4.1 and 4.2. of this Agreement, or due to the technical problems of the buyer's postage server or other reasons, the buyer must contact the seller and report on the non-treatment of the goods. In this case, the Seller will free shipping for 2 (two) working days from the date of receipt from the buyer the corresponding message.
5. Prices and payment procedure
5.1. The range and price of digital products are presented in free access on the seller's website.
5.2. The cost of the goods listed on the website of the site can be changed by the seller in unilaterally Anytime.
5.3. Payment for digital goods is due to cash with payment systeminstalled on the seller's website.
5.4. The obligation of the Buyer for the payment of goods is considered executed since the receipt of funds for the settlement account of the Seller
6. Specifications of digital goods
6.1. Digital goods are supplied in the following formats: PDF format, JPG format, MP4-format, XLS format.
7. Rights and obligations of the parties
7.1. Rights and obligations of the buyer:
7.1.1. The buyer has the right to give him a digital product in accordance with the technical characteristics marked in this contract (paragraph 6)
7.1.2. The buyer is obliged to pay for the digital product in full until the digital product is obtained.
7.1.3. Products purchased from the seller are intended for personal use by the buyer. The buyer undertakes not to disseminate copies of the digital product in any form and in any way.
7.2. Rights and Responsibilities of the Seller:
7.2.1. The seller has the right not to supply digital goods for which they are not received cash in full.
7.2.2. The seller is obliged to put a digital product in proper quality in accordance with the technical characteristics denoted in this contract (§ 4).
8. Responsibility of Party
8.1. For non-fulfillment or improper fulfillment of obligations under this Agreement, the parties are responsible in accordance with the current legislation of the Russian Federation.
8.2. The seller is responsible for the compliance of the Digital Product technical characteristics designated in clause 4, as well as for the compliance of the content of digital goods to all norms of the law.
8.3. The buyer is responsible for the proper use of digital goods in accordance with paragraph 7.1.3.
8.4. The seller is not responsible for the content and accuracy of the information provided by the Buyer when placing an order.
8.5. The buyer is responsible for the accuracy of the information provided when the order is issued.
Requisites of the seller
IP Klimov Alexander Nikolaevich
OGRNIP 311222511700014.
Site Privacy Policy Website
This site is an information and educational Internet project Klimov Alexander Nikolayevich (IP Klimov Alexander Nikolaevich. OGRNIP 311222511700014).
On this site, the following principles of confidentiality policy are strictly followed:
1. Subscription to the newsletter is carried out by their own solution to any wishing through the form on this site. For this, your email address is requested. You must also confirm your consent to obtain information materials, in a letter that comes after filling out the form.
2. Personal data of each subscriber is used only to send it periodic release issues, news and project shares: and never in any form will be transferred to third parties.
3. To obtain an idea of \u200b\u200bthe content of mailing issues, you can get acquainted with the content of the site "Blog" site:
4. Each subscriber at any time can refuse to receive mailing letters by clicking on the link present at the end of each letter.
If you explore the section on Forumhouse " Homemade machines, Tools and Mechanisms ", you can find" 1000 and 1 option "devices for self-building, which you can not buy in the store. It may be a rack for "Bulgarian", for accurate and fast cutting metal profile, lathe mini-machine, as well as all sorts of reinforcement and pipe bending and plans for aerated concrete. Interesting multifunctional and inexpensive sawing table, which created a portal member with nickname iD215711128.
iD215711128.
- How to make a sawing table for circular saw.
- What materials and details are needed for this.
Universal sawing table for disk saw
So, U. iD215711128.there is a powerful circular to which for more than 20 years. The depth of the saw saw is 65 mm. In the course of its operation, it turned out that it was difficult to achieve high-quality sawmaking of wood with its help. Causes: The adjustment of the corner of the disc and the depth of the cut is constantly knocked. Sole saw made of thin metalAs a result, it is shortened, and geometry is not withstanding when cutting the workpiece.
At first, the user went to the standard way - began to refine the saw. Made adaptations to comply with the perpendicularity of the cut. Lined the clins to comply with the depth of cut. I embedded the saw in the table, as it is, but the thread of the M4, on the racks of the circular, weakened and each new passage had to configure again. Despite the complexity of sawing, iD215711128. Made 5 casing boxes. "Accident", which gave impetus for the construction of multifunctional sawing tablehappened when the sideline did the sidewalls for the door cluster.
iD215711128.
I saw a two-meter bar. Already chose a quarter, cut the locks, it remains to choose longitudinal groovedesigned to fix the product on the wall. He made a saw of a few cuts and, when the workpiece was almost ready, the depth was killed in the circular. I practically saw the timber in half, completely spoiling the item. Everything, on this, I realized that I would have enough of these "dances with a tambourine", and a normal sawing table is needed.
First, the user bought in building hypermarket Phaneur for countertops. Then developed technical taskWhat the requirements must be answered. So:
- You need the highest possible departure of the saw disk.
- The saw blade must have an adjustable angle of inclination - 90-45 degrees and departure 0 - max with reliable fixation of the specified parameters.
- The details of the large cross section should be placed on the table, therefore the size of the table - 1.22 x1 m.
- You need adjustable and reliably fixable parallel focus, as well as customizable horizontal and vertical fittings for the parts being processed.
- The table should be multifunctional, with the possibility of further installation of the mill and electric jig.
On the topic "Universal fittings of the joinery", we recommend reading the articles: and.
Deciding with the requirements iD215711128.thought about what to make the mechanism of lifting and lowering the saw. The choice fell on the car screw rhombic jack.
But, walking in the store for bolts, hairpins and nuts, the user forgot it there to buy. Because I did not want to return back, the home owner decided to replace the jack on the clamp, from which he cut off everything too much and welded the right one.
The design of the lift turned out simple and reliable.
Next came the cereals of the circular upgrade. With her, the user removed the sole, the cover of the saw blade, because It prevented, and disk protection. Disassembling saws was carried out with the calculation, which, if necessary, it will be possible to raise it. The saw installed on the lift.
The slope of the saw is carried out using a homemade rotary mechanism made of studs and boards.
According to the self-dealer, due to the metric thread, the handle has to rotate a large number of revolutions, but with an infrequent reconfiguration of the machine it is noncritical.
Parallel emphasis has a length of 1220 mm. To exclude the shift of the distant edge of the workpiece during its sawing, the emphasis is equipped with an additional retainer.
All items are well adjacent to each other and accurately fixed on the table, because It depends on the geometry at the outlet of the saw blade.
iD215711128.
Testing the machine showed that everything works as it should. The tilt corners and the depth of sawing are not shot down.
At this stage, the user took a timeout and thought how to upgrade the machine for sawing large blanks. The carriage came to mind, but it will eat about 1 cm of the depth of the cut. It can be critical, because Details of casing are made from timber and have dimensions of 1.5-2 m, with a section of 10x20 cm. In addition, such a ram weighs a lot, and it is uncomfortable to push it on the table. Exit - the workpiece is on the spot, and the saw itself moves.
iD215711128.
I remembered that when I saw Paneru in a construction hypermarket, they did this "cunning" machine, sawmill Which goes from above-down and from left to right. After thinking, I decided to make a cart with rollers and correcting, which will move in a saw.
For the manufacture of the device, the user bought rollers for a furniture trolley and a 5x5 cm. First iD215711128. I decided to put only lower and horizontal rollers. But, because Due to the application of effort when moving the trolley, there may be a skew, the master put additional rollers on the trolley, which rest in the lower surface of the table top.
Those. The cart is fixed in three directions. It provides high accuracy Her movement.
During the "run-in" of the table had to regulate the coaxiality of the direction of the cut and the direction of the movement of the trolley.
For this, the washers were put on the fastening of the guide corners.
Adjusting the machine, the home owner experienced it, sawing the board with a cross section of 20x5 cm.
During the disk, in 260 mm, this turned out to be sufficient for precise sawing of the workpiece.
d215711128.
Taking as the basis of a simple circular, I managed to make a sawing and tracing machine with the possibility of longitudinal and transverse sawing. You can cut or rigidly fixing the circular, moving the workpiece, or moving the saw, with the blanks of the blank with the adjustment of the depth and inclination of the disk. I plan to still modify the machine to make it more functional and more convenient. To do this, put:
- Quick-proof fixed focus with the transportation of billets at any desired angle when moving saw.
- Movable transportation for handling small wooden products With a fixed circular.
Also user installed eccentric clamp To fix the carriage in any of the positions of the saw.
The circular machine is the tool without will not be able to do any house master. This equipment is especially important for country house or cottage. But to work manual machine It is not always convenient, and the factory machines are quite expensive.
The output from the current situation can be the manufacture of this device with your own hands. The basis of this machine may not only be a manual circular saw, but even an electric drill or Bulgarian.
Make a bird for circular Machine do it yourself very simple. For manufacture, the most ordinary pilomber And quite a bit of time.
Before thinking through the design of the upcoming machine, you need to calculate the load that it will be exposed. The main thing in the bed is reliability and stability. For powerful production saws the base is welded reinforced metal design. But for use with your own hands, such an aggregate is not needed.
If you just decided to make your woodworking machine, then you need take into account the main parameters equipment. Since the saws can be different, naturally can be the design of the bed.
First you need determine the power tool. Usually for homework Choose equipment where power parameters do not exceed 850 watts. But, for example, in the construction of a cottage or country house, it is often necessary to cut a very large amount of wood.
That is, and the power of the circular is required more. But experienced masters Do not advise buy saws, where this figure is more than 1250 watts. Installing this equipment in the home workshop is absolutely not justified. And the work on it will only increase the cost of electricity.
The larger the machine performance, the stable for it it is necessary. For professional circulars, as a rule, establish the basis, steel profile. Sometimes these birds are even concreted into the floor. Since the vibration of the device can lead to a danger to life.
Technical Features of Circular Machines
Depth of the alleged cut. This parameter depends the thickness of the material to be processed on your machine. This indicator in semi-professional and professional machines ranges in the range of 5-8 cm. For cutting boards and thick plywood, this is quite enough.
But it will be inconvenient to work with the brothers on this machine. In addition, it is necessary to consider that this characteristic of homemade saw decreases. The depth of the cut will be less than approximately 1 cm. But this can be avoided if you provide in the table of the table the ability to omit or lift the disk.
In the manufacture of the tool you need take into account the frequency of its rotation. If the circular is required for the workpiece of the building material, then this indicator may be less. If a clean and even cut is required, the rotational frequency is needed quite high. It is necessary, for example, for the manufacture of furniture.
But in this case there are certain nuances. For cutting plastic materials This saw does not fit. Due to the very large turns of the tool the disc is heatedAnd plastic begins to melt.
Therefore, it is better to choose a device where the speed of rotation is not more than 4500 rpm, in this case the bed for circular saw can be make from wood. The vibration of this machine is low and the additional strengthening of the table is not required.
Well, at the end that it is necessary to foresee, this is the location of the buttons and other controls on your machine. When assembling saws, do not forget that access the control panel must be safe. Moreover, this is the rule in the case when the open part of the saw is located at the bottom of the table top.
In this design, the panel with switches is best postpone from the outside of the machine Either make a rising countertop. This design is convenient for maintenance of the device. Then, when you took into account all the nuances and trifles, you can start directly assembling the table.
Making a circular saw with your own hands
The easiest option of the beds for the circular is a design made from boards and thick plywood. And directly the tool is attached to the bottom of the stationary countertop. For a saw in the table lid, a special slot is made.
Dimensions for the table can be changed as it will be convenient for it to work on it. For example, the middle table is described, the height of which is 110-120 cm. But there is a lot of depends on the growth of a person working with equipment. Also, at your request, you can change the length of the tabletop.
If it is supposed to work with boards, in which the length is more than 2.6 m, then the lid on the bed will need more. In this case, it is necessary to make changes directly to the design and additionally. add a few supports (legs). Otherwise, the table will create strong vibrations.
For countertops usually used plywoodwhich has a thickness of at least 5 cm. But you can also choose a plexiglass or stove of fiberglass. But the use of chipboard professionals are not recommended, this material is not reliable enough.
Tools and materials for assembly
For circular saw, you must provide for the guides. They help to cut wood much more accurately. This design weld from steel corner And fixed to the lid of clamps.
Fasten the same stationary guides is undesirable, since later you will not be able to change their position.
For the construction of the table you will be needed such materials:
- iron sheet;
- plywood sheet;
- bar size 50 × 50 mm;
- 50 × 100 mm size board;
- steel corner for guides;
- two clamps;
- manual circular saw.
You also need to pre-cook all the tools that will be necessary for the background assembly:
- Sculpture, electric drill.
- Hacksaw or electric jigsaw.
- Measurement tools (roulette, square, ruler).
- Manual milling cutter or milling machine.
When everything is prepared, you can begin the assembly of the table itself. Sometimes masters collect countertops from unnecessary dining or kitchen tables. But this design is unlikely to serve for a long time. Therefore, much more intelligently all elements of the design make with your own hands. In this case, you can also take into account your personal needs.
Making countertops for circular machine
Assembly of the table start from the manufacture of table tops. Plywood sheet It is placed so that two edges of the lid are in size with the edges of the iron sheet. Phaneur is cut with a hacksaw or an electric bike.
The edge of the spike can be treated with a cutter, but this operation is optional. Since in the face the main parameter is reliability, and not an attractive view. The countertop rubbing "Naturally" sandpaper.
From the bottom of the countertops noted slot for circular circle . For which at first it is necessary to measure the size of the soles of the aggregate. It is easiest to do this if you unscrew the disk from the device and simply bore the desired part of the saw. These measurements are required to determine the seating.
With help manual cutter Choose bars to a depth of approximately 0.9-1.1 cm. If you do not have a cutter, then this work can be done using the bit, but this will take it much more.
Then, when the seat is done, try the saw, and if necessary, adjust the recess. Follow the spaces of the slot for the circle and fixing fasteners. If you need a circle to raise and lowered, then it is necessary set pendulum mechanism For countertops.
In this case, the slot must be made in the form of a truncated pyramid. In this case, the hypothetical peak of the pyramid will be directed down. Directly frame for lifting mechanism the best thing make from steel cornerswho are welded with each other.
Making frame frame
Markup for fixing transverse speakers and longitudinal, which perform the function of rigidity, it is best to install from the wrong side of the table top. Directly the planks are made from the bar. You will be needed:
- Two transverse parts, a long equal tabletop width minus 7-9 cm on each side.
- Two longitudinal ribs, the size of equal length of the lid minus 7-9 cm on each side.
Then need make nest for screws. The rails need to be fixed on the lid so that the countertop goes beyond the edges of the frame by 7-9 cm. Fasteners should be as reliable as possible and durable.
The first mount must be set by approximately 40-50 mm from the edge of the rail. Distance between self-sustaining approximately 23-25 \u200b\u200bcm. All items you need to drill through. Saws is attached from the side of the lid so that its hat is completely accumulated in the tree.
Initially fasten the transverse ribs. So that the table lid was as strong as possible, the edges of the rails are predefined wash in joinery glue. The design is fixed by clamps, and without removing them, screws the screws.
The countertop is allowed to dry. After, the longitudinal rails are installed in the same way. Then parts of the frame are tightened with each other by installing two fasteners on each side. Now clamps can be removed.
Fastening legs (supports)
The stands of the table are made of bar. The height of the support is selected individually. In practice, it is more convenient to work at the machine when the countertop located at the hinder level. Before mounting each support, you need to compatinate it so that the leg came down from below. So, the base of the support should be slightly larger, unlike the top area.
It is best to fix legs with steel corners. They need to squeeze a bit so that the base of the machine is in the "strut." It gives the table additional resistance. As a fastener, bolts with washers are used, they are attached to the hats outside. Otherwise, during work, you can be injured about the protruding pieces of fasteners.
The whole design will be stable if additional supports are pulled by diagonal slats. They are fixed in pairs from each side of the machine.
Surface cover polished and treated with varnish Or used to cover a steel sheet, which is attached to the screws. At the very end, to the prepared place, the instrument is fixed directly.
On the cover of the table can be additionally make markingShe will help smoothly and properly saw wood. Circular saw control panel placed on outside Machine. As a rule, it is fixed on one of the legs of the table. That's all, circular saw with their own hands ready.