Machine vice for cylindrical parts. What is the purpose and the device for the testicles of plumbing different types? Characteristics of rotary cast iron eating vice

Useful mechanical device used by masters for fastening parts in the process of processing, are vice. They are effective in cases where the installation of the workpiece on safe deletion Or it is necessary to hard and reliably fastening it. What types of devices exist and how to choose them will be told in this article.

Design features

Enlarged this device consists of two sponges, one of which is fixedly attached to the housing or bed, and the second is movable, capable of moving. To clamp a blank in sponges, a fixing mechanism is used. It consists of several elements, which can be seen in the photo of the vice:

Steel chassis screw with a trapezoidal thread. The rotation control of the screw is carried out with the help of a handle.

Pig-iron plate for support or bed. It is possible to use steel or duralumin design.

Sponges have a screw mount. If you rotate the screw in the direction of the clockwise direction, the movable sponge begins to move to the bed, fixing the part. When rotating the screw in the opposite direction, the sponge goes from the bed, freeing the workpiece.

For fastening the vice on the support, several ways are used:

• stationary with regular use in one place;
• on the clamp, which provides smaller fastening reliability, but the possibility of using without a permanent workbench;
• at suction cups - used when attaching exclusively on a flat and smooth surface.

Tool varieties

Tiscovic machines are usually classified depending on the technology used when activating the screw. They can be manual and pneumatic. Based on the design features, rotary vice and non-reflective are used.

Some manual models allow manipulation with long items. For these purposes there is a broad anvil and the possibility vertical fastening blanks. There are also models for the clip of rounded parts.

Flooring type of tool

Special bolts are used on the workbench or desk. All-metal device design.

There is an opportunity to choose a stationary or swivel model in order to process parts with the possibility of changing the corners. The width of the sponges varies within 45-200 mm with the possibility of a sponge of 140 mm.

Advantage this type is the wear resistance of sponges, the strength is applied, small sizes And the mass, the possibility of turning 360 degrees in turning models. However, at the same time:

• require constant alignment of the position of sponges;
• equipped with wireless locking washers;
• the clamp of long blanks is difficult;
• they have a backlash.

Flooring vice can be parallel and table. In parallel, the sponge offset is provided by the rotation of the screw parallel to the stationary part. They may be swivel and non-reflective.

But the dining room model is an obsolete version. Although this is a very simple vice design, long items can be clamped.

Machine design

This is a more accurate version of fixtures for fixing parts. He does not have a backlash in general, or the magnitude of the run is minimal. Things are attached to the workbench, differ in the presence of a rotary mechanism.

You can select one of the following options:

• stationary with fastening perpendicular to the position of the instrument;
• sine with installation details at an angle;
• multi-axis with the ability to turn over several axial points.

Machine vice guarantee a durable clamp, which is especially important when processing metal details. They are equipped with a solid body and protective anti-corrosion coating. Hard fixation provides high accuracy work.

However, with a curved clamp of the workpiece on it there may be traces. Therefore, it is required to use foil laying or fixing the parts only to the upper part of the sponges.

Manual vice

This is a portable compact tool that does not require stationary fastening. Thish are used to handle small parts. Distinguish two constructive options:

• with the presence of sponges together with screw and handles;
• lever vice resembling pliers with a closing mechanism.

They are used for accurate works, are characterized by a minimum level of backlash. Design is adapted for manipulations with aluminum profile and metal tile. With their help, you can clamp flat blanks.

At the same time, they are not adapted to work with large blanks, required additional elements When manipulating at an angle. While working with soft metals, traces remain on the workpiece.

Joinery design

These vice are applied in operations with wooden or plastic details. On the sponges are placed lining from wood, which eliminates the appearance of traces from the clamp. If the attachment of the unit is performed front, then it is possible to work with vertically fixed billets. Some models provide a quick-pressure mechanism.

With all the advantages of other types of desktasses, a joinery model allows you to high quality processing products from soft materials. Large parts are processed in the same plane.

The solution of sponges is large enough, there are several options for the fastening system. However, you will not work with tough items, since the seizure is not solid enough.

Features of choosing tool

You must choose the design you need based on the parameters of the working items:

• the size of the sponges, their width, the possibility of using lining is the factors that provide a more durable clamp the parts and quality of processing;
• the deep course of the clamping mechanism provides greater versatility and functionality;
• the presence of a reserve is positively assessed over the elevation of the workpiece to enter the part itself;
• the handle must be comfortable and ergonomic - metal design big diameter Provides the comfort of the operator.

How to work with vice

Using vice in the work, you should not increase or increase the handle in a different way. Also should not clamp hot steel products. The bending of parts can lead to the damage of the clamping device itself.

If you set yourself a question, how to use visets correctly, you should not forget about the need for regular care tool.

After each application, vice must be wiped with a solvent applied to soft fabric. All nodes should be regularly lubricated with machine oil to preserve and prevent corrosion.

DEXX, IRWIN, KRAFTOOL, STURM, WOLFCRAFT, ZUBR are highlighted among popular and reliable manufacturers. Semit suitable model, do not forget to be interested warranty obligations and service conditions.

Photo by Tiskov

It is unlikely that there is a more necessary device in the home workshop than the locksmith vice. Even if you are mostly working with a tree, sometimes you will not be able to do without a vice. And if you do not have a workshop, a garage or a corner in an apartment where you can replace non-hard economic utensils, the presence of small desktop plumbing languages \u200b\u200bcan be healthy to rescue in many situations, turning kitchen table Or even a stool in the ministerial.

First of all, about the appointment. Task's task - securely fix and hold the part or workpiece when processing it various tools. Depending on which items mainly need to be fixed in vice and what tools will have to work with them, the structural parameters of the vice are varied. But the most universal and most common look like this:

The basis of any vice is a screw pair. In most cases, the screw is fixed in the rolling part of the body of the vice, and the nut is in a fixed, which is either directly or through the rotary mechanism is attached to plumbing workbench Or a special stand that ensures the devices of the vice during any operations with the detail enshrined in them.

Types of plumbing vice

In addition to reliable support, you must clearly understand what types of work you will perform, and relate the choice of tabletopes with them. First of all it concerns the material of the case. In the post-Soviet space, the cast iron is more often.

This material is solid, wear-resistant, but rather fragile. Therefore, if you are not going to bend with a sledgehammer thick steel blanks without serious preliminary heating, then boldly take such vice, and if you are going, then it is better to look for steel.

If you need to regularly mount the blanks of a cylindrical shape regularly, it is desirable to make a lining on a sponge with a triangular neckline. And if such operations are quite frequent, we advise you to consider options constructive execution Flooring vice, somewhat different from standard.

In general, if we talk about the functionality of plumbing vice, then first of all it is worth thinking about the size. If you know exactly what you do not have to work with overall details, do not pay for extra metal, and it is possible to consider even compact machines.

Or vice versa - option is possible with large-sized parts, but without special efforts When processing them. Then you can consider the variant of the testicles with the possibility of preliminary spuning of sponges without using running screw.

If you do not have a workbench, and also in the list of works more transactions that do not require rough applications physical strength To the processed details, the option with desktop visits, fixed using various clamps - yours.

True, the latter are minid, it is better to have in the farm as an additional. There are no big parts in them, and there are no serious effort to the processed workpiece, you do not attach - insufficient clamping efforts to hold the testicles themselves, but make the key from the castle in the sample.

In addition, such testicles are sometimes indispensable if you need to unscrew the baked nut when you can use them as hand tool. Despite the miniature sizes, they have a very good sponge.

It is also worth mentioning small visits on a ball joint, which serve for the convenience of processing very small details. complex configurationallowing processing different surfaces Details from one consolidation.

It is clear that the effort of the clamp of the ball hinge is not enough for serious physical exerciseSo such vice are suitable for quite specific types of work. The same, in our opinion, not very serious, there will be tice with fastening with the help of a suction cup.

For their more, less reliable consolidation is needed either well polished surface or glass. On other surfaces, it is unlikely to securely fasten them. And the functionality also is also small.

For all types of plumbing vice, you will obviously use additional lining for the fastening of parts from soft materials.

Some desktop vice Have a pneumatic receipt that significantly facilitating the process of fixing the workpiece.

But if you have no locksmith minor production at home, it is unlikely that such vice will be useful to you.

What else is important to know when choosing a plumbing vice? There are quite a lot of complaints from users to Chinese vice with cast-iron housings equipped with fastening clamps - are often laid out, therefore, if you want cheap vise from the subway, it is better to choose from steel.

Choose a vice, which, with the least divided sponge, the smallest backlash between the details of the case. Also, if you do not need a turning mechanism for work at the base of the vice, select the model without it: and save money, and the stiffness of the structure is higher.

How to make plumbing vice with your own hands

It is asked: why with such an abundance of sizes, forms and configurations of plumbing vice offered by the trading network, to engage them independent implementation. In the manufacture of plumbing vice, you can save up to 10 times in value, as well as make a device with specified parameters.

And it is absolutely real, because almost everything that can come in handy for the manufacture of desktop vice can be found in the reception items of the scrap metal.

This is especially good in a photo on which parts of the plumbing tube valve with flywheel are used as a screw pair.

Also a screw pair can be taken from the old vertical jack. Even if part of the thread was slightly increasing, then, as a rule, it small plot From the edge of the screw, which is so necessary to cut to shorten it. Also very durable driving screws of old lathes, screw presses T.P.

At worst, for very little money, you can order a turntable in the nearest vocational school of such a pair with a wide nut, with an ordinary metric carving. Only Diameter Make more, yes nut sewing. In this case, the force of the clamp will redistribute to enough large square Due to the diameter of the screw and the number of turns.

As a last resort, just buy in the store selling hardware, the stud diameter is more, and a high nut to it or a piece of 3 ordinary, which breed then sequentially scored on the heel.

Classic version of homemade tabletopes

By photographs, steel parts are clearly guessed, almost always without much difficulty selected in the nearby prominer:

• steel plate 200 x 200 thickness 3 - 6 mm (can be thicker);
• 2 channels (120 mm - outer, 100 mm - internal) length, respectively, 160 mm and 300 mm, in your case the dimensions can be different depending on the length of the head screw;
• steel ears from some large-sized capacity;
• 2 worn turning cutters;
• pond for a turn, in this case a piece of reinforcement;
• screw or stud, corresponding to the rod diameter, and 2 nuts;
• 2 washers, diameter corresponding to the diameter of the running screw;
• screw pair - any of those described (in this case - ordered by turning), 335 mm long;
• powerful plate for fastening the running screw.

The chassis of the screw on both sides of the plate is separated by the washers, one of which from the threaded part is taken to it with welding, although with such a diameter it can be consolidated with a pin or locking ring. Then this node will be completely collapsible, which is clearly better for reasons of maintainability.

The handle on the one hand is faded with a welded nut, and from the second side it is collapsible, after welding to it threads from the screw of the corresponding diameter.

Nut from a screw pair is welded to the base plate flush with the 120th channel.

For the normal entry of the inner channel with the driving screw fixed on it, its ribs need to be slightly treated with a file.

Ears with welded sponges made of cropped turning cutters, you need to position at the screwdriver screw. So they are born accurate place. You can even twist the sponge together soft wire, ensuring their perfect interpretation.

You can also apply a notch to them with an angular grinder with a disk for metal cutting.

Due to such fastening of sponges, namely, the shapes of the hooks and distances between them, in such vice you can attach non-standard details extended to the bottom.

Yes, and the maximum thickness of the workpieces being processed in these vice are very impressive. And I don't have to talk about the maintainability of such a snap and talk - you see.

Dear readers, if you have any questions, ask them using the form below. We will be happy to communicate with you;)

In order to understand why it serves as a vice, it is worth considering the device of vice for fitter work. Use them for durable and fixed fixation of parts. Without teas even good master It will be helpless. This tool has become indispensable in the home workshop, and in production. During the long years, the existence of vice has undergone many changes, but the basic principle remained unchanged - reliable fastening between sliding planes.

Maintenance vice is widely used in household and factory workshops for reliable fixation of details.

Structure of this tool

Things are made of a variety of models and forms. They are also used very widely, from households to factory workshops.
Despite a variety existing varieties Such a tool as vice, all data Tool types include the following details:

• mobile sponge;
• stationary sponge;
• screw clamp;
• spring;
• screw knob;
• sleeve;
• mounting mechanism for workbench;
• replaceable overlays.

Flooring vice is made of steel carbon or gray cast iron. The device is attached to the table or to a specially intended stand by bolts or special clamps. It is usually fixed one of the tool lips, which is called - fixed. In turn, a mobile sponge is defined to it.

They communicate with a straight screw with a straight screw. This item is driven by a handle. The screw rotation process climbs or removes a movable sponge relative to fixed. Due to this, it appears the opportunity to hold one or another billet between sponges. Usually, an anvil is located on the reverse part of the device so that it is possible to increase the possibilities in the processing of parts.
A certain kind of devices can be applied depending on what the character is executed.

Main types of this tool

Consider the most common from plumbing vice.

1. Thinking vice. Typically, these types of vice are used when you need to perform. heavy work where you need to beat, roll, bend, etc. They are called so because their fastening looks like a chair. Initially, they were attached to a wooden base.

Later they were adapted to the installation on metal workbenks. A constructive difference from the rest of the clamping devices is that the stationary sponge is fixed in two places. It is attached to the horizontal plane using a special plank, called a paw, and the bottom, elongated part, can be attached to the feet of a table or workbench.

Such a fastener makes them resistant to strong side shocks. Another sponge is movable. Screwing the clamping screw, the vice hold one or another detail with both sponges. The unscrewing is accompanied by the fact that under the pressure of the spring, the movable sponge facilitates the effect of vice on the workpiece. So that the vice is not bent and not broken, they are not poured, but they will be removed from special carbon steel.

The width of the sponges can be changed and used depending on what the sizes of the vice. Usually use sponges 100 mm, 130 mm, 150 mm, 180 mm. Also, the challenges are divided into other characteristics, for example, this classification depends on the greatest size Details that can be processed. There are several types with split sponges by 90 mm, 130 mm, 150 mm and 180 mm.

The working parts of the vice are plates located in the upper part of the sponges in special notches.

Plates are rotated, on one of the surfaces notches are made for a strong capture of the part. They are or welded to the sponges of the plate, or fixed with bolts. To do this, the plates are made of openings with recesses for bolts heads.
The headbands have both advantages (simplicity of fastening and reliability) and disadvantages. This type of tool is designed to work with rude materials and is not at all suitable for thin work. The fact is that the clamping plates of sponges are not always arranged in parallel to each other and when the clamp is crashed into the part and spoil its surface with dents.

This design allows you to clamp thin parts only by the upper edges of the lining, and thick - only lower parts. From this clips fortress decreases. To avoid this, the screw is tightened stronger. This effort may not withstand the surface of the workpiece.

There are so-called parallel vice. Rather it would be necessary to say with parallel sponges. In this design, it was tried to correct the lack of challenges of vice. This type of clamping mechanisms has become the most used and convenient to work. They are made of cast iron and from special elastic carbon steel. Before buying or starting working with vice, it is advisable to figure out what the unit is made. Cast iron products are more fragile and need to special relation. The cast iron does not like shots. In addition, on the locksmiths should not be treated with heated parts. When cooled, the size of the workpiece changes, which can lead to injury to the wizard.

Types of parallel vice

The plots of this type are divided into stationary and swivels.

Non-reflective vice are attached to the workbench, and you can only work on them in the same position. To change the angle of the processed detail, you need to weaken the screw clip using the clamping screw, change the position of the part and start it with sponges again.

To avoid constant change in the position of the part, invented a tool of this type with a turning base. They are arranged in this way: the base of the vice is hard attached to the workbench. It joins the rotary part of the stationary sponge using the adjusting screw with the handle. When weakening this screw, the vice can be rotated around the vertical axis. Different models rotate on different corner - from 60 to 360 °.

In a stationary sponge, a rectangular hole is made, where the pressure screw of the movable sponge is injected. Moving in this hole with a screw, the sponges will bring up and remove the clamping pads strictly parallel to each other. This method of the clamp allows you to fully control the processed item.
Since the housing is made of cast iron, to increase the tool service, the lining is made of steel. They are fixed in the upper parts of sponges with bolts. On the working surface of the lining make notches for a more dense clamp of the processed part. When need to do finishing processingThe steel linings are plates made of soft metal. They protect the detail from dents and scratches.

Pros and cons of data tools

Most often in practice, parallel swivel and non-reflective tools with a rear stationary sponge and anterior stationary sponge are applied.

Together with the advantages of such vice, there is a significant drawback - a weak fortress of sponges. That is why the tools of this type are not suitable for difficult work. For shallow and accurate work, vice is made, which are sometimes called manual, with the size of sponges 35 mm, 40 mm, 50 mm and 56 mm. They are revealed, respectively, 28 mm, 30 mm, 40 mm, 50 mm and 55 mm. They are arranged by the same principle as the challenges of vice. The detail is made between the lips with a screw with a swivel lamb, and for squeezing, except for the screw, there is a spring from carbon steel grade or grade 65g.
Using handicrafts for fastening parts with their hands (both or one). They use when the workpiece is uncomfortable or dangerous to hold in their hands. In order to work with small details Two hands could be carried out more accurately, clamping handicrafts in ordinary, located in parallel.

Another kind of plumbing vice-tube. Flat working plates of ordinary vice are not able to hold hard round shape. The area of \u200b\u200bcontact with the linings with the pipe is very small and it becomes almost impossible to process it. Such tools are specifically designed for this purpose. The concave form of sponges allows you to tightly clamp a pipe or another round item.

When fasteners, it is not recommended to increase the power of the clamp using additional copies to the screw handle. You should not wear a pipe on the handle or replace it with a steel rod of greater length. The original handle is designed precisely for clamping with hands, so with an increase in the load you can withdraw a tool.

• Pneumatic vice with swivel hydraulication.

• Machine-grinding machines.

• Machine vice swivels.

• Visits Machine rotary and non-referential.
• Pneumatic machine vice.

• Thirts of plumbing upgraded
  (Professional) TCM.

Visks Machine cast iron (BZSP).

Visks Machine cast iron non-turning.

Visks Machine cast iron
The accuracy class of N and P according to GOST 16518.

• Installing vice on the table The machine is carried out using a key, fastening - with bolts.

Characteristics of non-reflective cast iron eating vice:

Model	IN Sponge width mM.	BUT Sponge consumption mM.	B1. Width, mM.	L. Length, mM.	N. Height, mM.	h, mM.	b, mM.	b1, mM.	C, mM.	An effort clamp N.	Weight, kg	Price, rub.
7200-0209-02	125	130	176	349	105	47	14	14	150	20000	13	11 100
7200-0214-02	160	200	176	424	114	50	14	14	150	25000	19	13 800
7200-0219-02	200	250	251	546	146	65	18	18	210	35000	41	19 400
7200-0219-04	200	250	250	521	141	66	18	18	210	35000	32	18 900
7200-0224-03	250	320	326	644	183	80	18	18	280	45000	72	28 200
7200-0224-04	250	320	316	641	172	80	18	18	280	45000	54	23 800
7200-0227-02	320	400	382	780	197	100	22	22	340	55000	96	36 400

Visks Machine cast iron swivels.

7200-0204-13, 7200-0206-13

Characteristics of rotary cast iron eating vice:

Model	IN Sponge width mM.	BUT Sponge consumption mM.	B1. Width, mM.	L. Length, mM.	H1. Height, mM.	N, mM.	h, mM.	b, mM.	b1, mM.	n.	An effort clamp N.	Weight, kg	Price, rub.
7200-0210-02	125	130	198	396	132	105	47	14	14	2	20000	17	13 800
7200-0215-02	160	200	198	472	141	114	50	14	14	2	25000	23	17 100
7200-0220-02	200	250	275	598	180	146	66	18	18	2	35000	51	23 900
7200-0220-04	200	250	270	548	171	136	66	18	18		35000	38	22 000
7200-0221-02	200	250	275	598	180	146	66	18	18	4	35000	56
7200-0225-03	250	320	340	709	223	183	80	18	18	2	45000	92	36 000
7200-0225-04	250	320	336	709	204	168	80	18	18		45000	65	29 200
7200-0226-03	250	320	338	709	223	183	80	22	22	4	45000	96
7200-0229-02	320	400	400	780	233	197	100	22	22	4	55000	116	43 300

Pneumatic vice with hydraulic amplification turning.

Visks Machine Pneumatic with hydraulic amplification Designed to secure parts in the mechanical processing of metals with cutting on milling, planing, drilling and other machines.

• The accuracy class of the TISS N and P According to GOST 16518 (DIN 6370).
• Cabinet parts of vice are made of cast iron.
• Installing vice on the table The machine is carried out using a key, mounting with n grooves B1.
• The clamping clamp is performed by a package of plate springs, which are pre-compressed by the power mechanism. The power mechanism is a built-in pneumohydroautylter.
• The clamp of the workpiece by plate springs ensures the safety of the fastening of parts with full air pressure drop in the network. Nominal pressure Air 0.6 MPa.

Characteristics of rotary cast iron eating vice with hydraulication:

Model	IN Sponge width mM.	BUT Sponge consumption mM.	h, mM.	A1, mM.	L. Length, mM.	B1. Width, mM.	N. Height, mM.	b, mM.	B1, mM.	n.	An effort clamp N.	Weight, kg	Price, rub.
7201-0009-02	160	200	50	4	521	280	176	14	14	2	30000	52
7201-0014-02	200	250	65	4	640	325	210	18	18	2	40000	88	60 300
7201-0019-02	250	320	80	6	720	338	240	18	18	2	50000	120	71 900
7201-0020-02	250	320	80	6	720	338	240	18	18	4	50000	120	79 000

Machine vice steel (BZSP).

Machine vice steel non-turning.

Machine vice steel non-turn from manual drive Designed to secure blanks during machining on metal cutting machines.
The accuracy class of the "P" according to GOST16518.

• Cabinet parts of violations of non-reflective, made of steel with heat treatment of guides. Installation of vice on the table The machine is made using a key, fastening - with the help of grabs.
• Configuring Tishov on right size It is made by fixing the bracket located inside the slider, pin in the housing holes.
• High hardness of working surfaces ensures the durability of the vice with the preservation of accuracy.

7202-0202-02, 7200-0205-02.	7202-0209-05, 7200-0214-02, 7202-0219-05.

H.acriterisics of steel non-reflective eating vice 7200-0203-02, 7200-0205-02, 7200-0209-02, 7200-0214-02, 7200-0219-02:

Model	IN Sponge width mM.	BUT Sponge consumption mM.	h., mM.	H. Height, mM.	L. Length, mM.	D, mM.	b, mM.	An effort clamp N.	Weight, kg	Price, rub.
7200-0203-02	80	50	30	65	220	190	12	6000	5	10 400
7200-0205-02	100	80	35	72	305	272	12	10000	10	12 600
7200-0209-05	125	125	45	110	407		14	30000	25	28 700
7200-0214-05	160	200	50	120	520		14	50000	36	32 800
7200-0219-05	200	250	65	153	630		18	55000	67	48 100

Machine vice steel swivels.

7200-0204-02, 7200-0206-02.	7200-0210-05, 7200-0215-05, 7200-0220-05.

Characteristics of steel swivel machines 7200-0204-02, 7200-0206-02, 7200-0210-05, 7200-0215-05, 7200-0220-05:

Model	IN Sponge width mM.	BUT Sponge consumption mM.	h., mM.	IN 1 Width, mM.	H 1. Height, mM.	L. Length, mM.	D, mM.	b, mM.	H, mM.	An effort clamp N.	Weight, kg	Price, rub.
7200-0204-02	80	50	30	134	90	220	190	12	65	6000	7	14 400
7200-0206-02	100	80	35	156	97	305	272	12	72	10000	12,5	18 500
7200-0210-05	125	125	45	200	145	465		14	110	20000	29	35 800
7200-02 1 5-05	160	200	50	245	160	524		14	120	25000	50	41 400
7200-0220-05	200	250	65	315	194	635		18	153	35000	86	58 700

Self-centered vice Designed to secure blanks during machining on metal cutting machines.

Characteristics of steel non-reflective self-centering machines:

Model	IN Width of sponges, mM.	BUT Sponge consumption, mM.	h, mM.	H, mM.	C, mM.	L, mM.	An effortclamp N.	Weight, kg	Price, rub.
7200-0209-12	125	125	45	110	418	366	20000	30	67 100
7200-0219-12	200	210	65	198	613	700	35000	90	124 700

Machine vice ("Metalist", Glazov, Russia).

TU396131-03-02962743-94.

Visks Machine rotary 7200-32.
Machine vice non-turning 7200-02.

Characteristics of eating vice 7200-32 rotary:

	7200-3208 (A \u003d 80)	7200-3210 (A \u003d 125)	7200-3213 (A \u003d 200)	7200-3218 (A \u003d 250)	7200-3223 (A \u003d 320)	7200-3228 (A \u003d 400)
Sponge width, mm	100	125	160	200	250	320
Sponge stroke, mm ± 10	80	125	100 200	125 250	160 320	200 400
Clamp height, mm	40	40	50	65	80	100
Clamping force given, not less	2000	2000	2500	3500	4500	5500
Shipping groove depth, mm	4	4	4	6	6	6
Shipping groove width, mm	14	14	14	18	18	18
Side of the Square Side Screw, mm	14	14	19	19	19	19
	40	40	45	45	45	45
Mass, kg.	16	17	27 29	33 34	55 60	74 83
Length, mm, no more	325	370	385 475	440 555	515 655	560 765
Width, mm, no more	280	280	320	320	400	460
Height, mm, no more	135	135	148	163	190	210

Characteristics of eating vice 7200-02 non-reflective:

	7200-0207 (A \u003d 80)	7200-0209 (A \u003d 125)	7200-0214 (A \u003d 200)	7200-0219 (A \u003d 250)	7200-0224 (A \u003d 320)	7200-0227 (A \u003d 400)
Sponge width, mm	100	125	160	200	250	320
Sponge stroke, mm ± 10	80	125	200	250	320	400
Clamp height, mm	40	40	50	65	80	100
Clamping force given, not less	2000	2000	2500	3500	4500	5500
Shipping groove depth, mm	5	5	10	12	17	17
Shipping groove width, mm	14	14	14	18	18	18
Stro-Rone Kvad-Rat of Soot-of-Screw, mm	14	14	19	19	19	19
Square length of the running screw, mm	40	40	45	45	45	45
Mass, kg.	10,5	11,5	21,5	26,5	49	68
Length, mm, no more	325	370	475	555	655	765
Width, mm, no more	180	180	210	210	280	340
Height, mm, no more	110	110	115	130	155	185

Machine vice (production of the Gomel Plant, Belarus).

GOST 16518-96.

Machine vice swivels.

GM-7216P (7200-0215-02), GM-7212-02P, GM-7216N (7200-0214-02), GM-7212-02N.

GM-7220P (7200-0220-02) GM-7220N (7200-0219-02)

GM-7225P (7200-0225-03), GM-7232P-02, GM-7225N (7200-0224-03), GM-7232N-02.

1 - Corps, 2 - Mobile Sponge, 3 - Rotary Plate.

Non-reflective: swivels:
GM-7212N, 7216N, GM-7220H,GM-7225N, GM-7232N. GM-7212P, GM-7216P, GM-7220P, GM-7225P., GM-7232P.

Characteristics of machines of swivels:

Model	Designation according to GOST.	Width sponges mM.	Sponges no less mM.	Worker height space mM.	An effort clamp kgf	Weight, kg	Height thish mM.	Price , rub.
GM-7212p	GM-7212P-02	125	150	47	2 500	18	120	8 400
GM-7216P.	7200-0215-02	160	250	55	3 500	29	145	11 700
GM-7220p	7200-0220-02	200	300	80	3 500	44	190	13 700
GM-7225P.	7200-0225-02	250	300	80	4 500	61	190	18 900
GM-7232P.	GM-7232P-02	320	400	100	5 500	138	215	30 300

Characteristics of eating vice without swivel plate:

Model	Designation according to GOST.	Width sponges mM.	Sponges no less mM.	Worker height space mM.	An effort clamp kgf	Weight, kg	Height thish mM.	Price , rub.
GM-7212N	GM-7212N-02	125	150	47	2 500	14	91	7 300
GM-7216N	7200-0214-02	160	250	55	3 500	21	120	9 400
GM-7220N	7200-0219-02	200	300	80	3 500	33	190	10 800
GM-7225N	7200-0224-02	250	300	80	4 500	52	190	15 800
GM-7232N	GM-7232N-02	320	400	100	5 500	100	175	25 500

Visks Machine Pneumatic with hydraulic amplification.

Characteristics of MM-7201-0019-02 machines:

Pipes of plumbing (production of the plant "Metalist", Glazov).

Visks Locksmith TCC series and TSSN.

TSS TSSN

Visits Merchant series TCC and TSSN Designed to secure blanks when performing plumbing operations, there is an anvil on the housing, the presence of prisms allows you to clamp round blanks, and the base design allows you to deploy visks from 0 ° to 120 °.
Case parts material - 35l steel

Characteristics of Locker Tischs TSSN63S, TSS80, TSS100, TSS125, TSS140, TSS160, TSS180, TSS200:

	TSSN-63-C	TSS-80	TSS-100	TSS-125	TSS-140.	TSS-160.	TSS-180.	TSS-200
Sponge width, mm	63	80	100	125	140	160	180	200
Clamping force, kgf	1000	1500	2000	2500	3000	3500	4200	5200
	40	50	70	80	95	90	90	90
Length of the stroke of the slider, mm	80	100	140	160	180	160	160	160
Mass, kg.	3,7	4,6	11,4	13	14	26,5	26,5	28,0
Basic length, mm, no more	230	255	345	380	415	450	450	450
Basic width, mm, no more	63	135	190	190	190	227	227	227
Basic height, mm, no more	200	120	160	175	190	210	210	210

Visks of plumbing upgraded (professional) TCM series.

Pipes of plumbing modernized (Professional) TSM series Designed to secure blanks when performing plumbing operations. The advantage of a new type of vice: allows you to clamp long blanks in a vertical position, round - in the prisms of the case and the slider. Due to the new design of the base, the vice can be deployed to any angle from 0 ° to 360 °. There is an enlarged anvil on the vigorous housing, the stopping bearing on the screw facilitates the closure clamp. The presence of adjusting screws in the housing allows you to install the required gap between the guides of the slider and the supporting part of the screws as wear, the initial adjustment produces a plant manufacturer. By order, non-reflective visks (without reason) TSMN are manufactured.

Characteristics of upgraded professional sheets of TISS TCM160, TSMN160, TCM180, TSMN180, TCM200, TSMN200, TCM250, TSMN250:

	TCM-160.	TSMN-160.	TCM-180.	TSMN-180.	TCM-200.	TSMN-200	TSM-250	TSMN-250
Sponge width, mm	160	160	180	180	200	200	250	250
Clamp force, (kgf)	3500	3500	4200	4200	5200	5200	5500	5500
Development. Moment<=кгс/м	14	14	20	20	25	25	25	25
Length of the sponge, mm	200	200	240	240	240	240	240	240
Depth of the workspace, mm	88	88	102	102	111	111	123	123
Mass, no more, kg	21	20	28,5	26,5	37	35	55	52
Basic Length, mm	487	487	555	555	555	555	595	595
Basic width, mm	203	203	230	230	230	230	250	250
Basic height, mm	210	186	244	215	261	230	281	251
Price, rub.	10 600

TIXES Florious cylindrical series TSC-180.

Characteristics of cylindrical plumbing TISS TSC-180:

Pipes of plumbing (production of the plant "GMZ", Gomel).

Certificate No.Sc. BYMM03.V02012.

TIXES Florious swivel Steel TCC.

TCS-125, TSS-140. TSS-150, TSS-160, TSS-180, TSS-200.

1 - Mobile sponge, 2 - housing, 3 - stove rotary, 4 - handle.

TIXES Florious swivel Steel TCCthe production of the plant "GMZ" is designed to secure blanks when performing plumbing operations, there is an anvil on the housing, the presence of prisms allows you to clamp round blanks, and the base design allows you to deploy vice. Case parts material - 35l steel

Characteristics of steel rotary locksmiths TISS TSS125, TSS140, TSS150, TSS160, TSS180, TSS200:

	TSS-125	TSS-140.	TSS-150.	TSS-160.	TSS-180.	TSS-200
Sponge width b, mm	125	140	150	160	180	200
Clamping force, kgf	3000	3000	5000	5000	5000	5000
	70	70	75	75	75	75
Length of the stroke of the slider A, mm	120	120	160	160	160	160
Mass, kg.	13,0	13,5	18,0	18,0	18,5	19,0
Length L, mm	360	360	390	390	390	390
Width B, mm	180	180	230	230	230	230
Height H, mm	170	170	180	180	180	180
price, rub.	4 100	4 400		7 100	7 300	7 600

TIXES Florious swivel cast iron TSH.

TIMS Fixer swivel cast iron TSHdesigned to secure blanks when performing plumbing operations, there is an anvil on the case, the presence of prisms allows you to clamp round blanks, and the base design allows you to deploy a vice. Material case parts - cast iron sch20.

Characteristics of cast iron rotary locksmiths TISCH125, TSC140, TSC150, TSC160, TSC180, TSC200:

	TSC-125	TSC-140.	TSC-150.	TSC-160.	TSC-180.	TSC-200.
Sponge width b, mm	125	140	150	160	180	200
Clamping force, kgf	3000	3000	3000	5000	5000	5000
Depth of the workspace H, mm	75	75	75	85	85	85
Length of the stroke of the slider A, mm	110	110	110	155	155	155
Mass, kg.	16,5	17,0	17,0	27,0	27,5	28,0
Length L, mm	385	385	385	460	460	460
Width B, mm	180	180	180	210	210	210
Height H, mm	200	200	200	210	210	210
price, rub.	3 500	3 700	5 400	6 000	6 200	6 500

TIXES Fixer cast iron TSH non-turning.

TU RB 490175790.001-2003.

Characteristics of cast-iron non-refinery narrowing TISS TCC250N:

	IN Sponge width mM.	BUT Sponge mM.	h. Clamp height mM.	An effort clamp kgf	L. Length, mM.	B1. Width, mM.	H. Height, mM.	Weight, kg	Price, rub
TSC-250N	250	200	80	6000	530	150	200	41	10 400

Material cast iron sch20.