The portal about the repair of the bathroom. Useful advice

How to make a desktop lamp. Lamp with your own hands (58 photos): options for desktop, suspended and wall lighting

If you are tired of boring and monotonous things in your apartment that you see every day, then it's time to diversify the design with Hand Made. Table lamp with your own hands is an excellent option to start. It does not require special skills and trouble, and the result often exceeds expectations. In this article we will tell you how to make a desk lamp with our own hands than to decorate it and how to connect it. We also prepared an excellent photo selection for your inspiration for creativity.

Table lamp do it yourself: the main elements of the design

The most popular and simple materials for creating a desk lamp do it yourself, it is: cardboard, paper, glass bottles, banks, plastic containers, pipes from water supply and cement. We will tell how from all this material to make a lamp.

The main elements of the design in the desk lamp of any type:

  • Electromechanical - Provides stability to a homemade desktop lamp and a safe supply of power supply directly to the lamp.
  • The support is supported by a reflector or illuminator.
  • Illuminator - Light bulb in the lampshar.

The desktop lamp electromochem is quite simple: network plug, cable, switch, bulb cartridge. Sometimes add voltage regulator. The cartridge for a narrow minion-base E14 is also attached to the thread or on the lamella in the form of a steel strip. For the desktop lamp, do it yourself the best option - chandelier cartridges with threaded flanges: between them you can hold the steel plank with the lampshar frame or the clamp for fastening on the hinge.

The table lamp must necessarily be electrically safe. This is especially true for lamps on hinges and consoles. Create desktop safety can be created using a simple scheme:

  1. The cable must be round, in double isolation
  2. Conductive cable veins are flexible, from numerous wires.
    The cross section lived from 0.35 square meters. mm.
  3. Cable wiring locations must be protected by dense dielectrics.
  4. The cable before entering from the inside is tied with a nodule or pull through the holes of the dielectric locking washer so that it cannot be broken. Next, it follows decoration and decoration.

Original lamp lamp lamp do it yourself

A lampshade must be manufactured taking into account not only aesthetic aspect, but also practical. It is important to fix it correctly, as well as make a comfortable opening for a light bulb. Paper, plastic and threads - materials that are most often used for the manufacture of homemade lampshar.

The simplest and most convenient material is paper. To create such a lamp, except paper, you will need: threads, PVA glue, sewing needle and scissors. There are many ways to make lamp lamp with your own paper hand. The simplest method is to dial the ball with paper stripes, while gluing them between themselves and on the poles. The form in the form of a sphere will further strengthen the continuing lampshade of paper.

Also elementary is the lampshade of disposable plastic cups, which are fastened by the stapler. This lampshade has sufficiently good lighting characteristics, but the appearance is quite utilitarian. Such a lampshade is well suitable for premises in which high-quality lighting is needed, but an aesthetic appearance is not required.

In the manufacture of lampshar of the threads, you will need at least 100 m. It makes no sense to use inflatable balls, like mandrels, because after 10-20 turns, the ball will begin to stretch in different directions and ruptures the shape. It is best for the mandrel to use tight-inflated, durable ball. The mandrel must be lubricated with vaseline. Further, pre-lubricate with glue, wind the thread on the ball. When winding, do not forget to leave the cable and cartridge hole. After a day, you need to blow away the mandrel, which, thanks to Vaseline, does not stick to threads. Also, threads can be replaced with jute, sisal or propylene twine.

Data lampshades form smooth soft light and so perfectly suitable for any room.

How to update lamp lamp lamp with your own hands

Old, boring, shabby and burnt lampshades can easily be updated with the help of healthy tools or create a new one at all. We will tell how to make it right and beautiful. As materials you can take any textile. Using fabrics and threads, you can sew or associate lamp shade in the form of a dress. Easy to decorate lamp lamp lamp with your own hands using: buttons, stickers, butterflies, beads, colors and various braids.

If you want to create an original label lamp tools, then here is a lot of ways. To create such a lamp, it will be suitable: lids from tin, disposable dishes, your favorite pictures from the photo of the album, paper with drawings or just a lampshade, disgraced by your hands.

It is enough to turn on the fantasy and you will get the original lamp in the interior of your home or apartment. In the photo below, see the selection of lamps for the table lamp with their own hands.


Hello to all lovers of homemade. I think every home has a light source, whether it is a lamp, chandelier or backlight, which in one degree or another to help in everyday life, but boast of originality Such devices can very rarely, since the manufacturer usually does not make a unique product, only except those What to order, but such pleasure will be hidden. It was about this that it was decided to make the original desk lamp of the beech with their own hands, and all who little worked with the tree the assembly of such a homemade will not seem impracticable. First you need to decide on the material and tools that will be useful in the manufacture of this self-made.

Before reading the article, I suggest watching a video about this homemade.

To make a desk lamp with your own hands it will be necessary:
* Booke boards
* Tree glue
* Pleismus
* Hand mill
* Grinding machine
* Sawing machine
* Clamps
* Furniture oil
* Drilling machine
* Dimmer
* Wires with fork
* Electric drill
* Sleeve with carving for furniture with M12 thread in 1,25 puzzle
* Super glue
* Stud M12 step 1,25
* Rubber screed
* Sandpaper

That's all you need to build such a homemade desktop lamp.
And now the most interesting, the assembly process.
Step one.
First you need to drive all the bokeh boards on the reysmaus, it is done in order for the thickness of them the same.








We do it from all four sides.


After that we saw a wide board into small suites, a width of approximately 5 cm, of which the lamp head will consist.




Step second.
After boards are ready, they must also be driven on the flight, and then cut into small blanks using a sawing machine.




Composite parts must be calculated in advance, the angle of sleep will depend on their number and the desired size of the lamp itself. For simplicity, we take 8 parts, on each of which you need to do with a drink under 45 o on both sides, it is done the easiest way on the sawing machine.












Step Three.
When all 8 blanks are adjacent to the size of them can be glued, it will help us with adhesive for wood. Before gluing, it is necessary to glue the glued surfaces to improve the contact stain.




We smear the glue throughout the area of \u200b\u200bthe junction of each part and fasten with the help of a rubber screed, it is to the word, you can easily be made from a bike camera.











Surplus glue by removing a cloth and leave to dry for a couple of hours, but for now the glue dries away three more such details.

Step fourth.
After drying all four octagonal billets, it is necessary to make a drink at an angle of three of them to create a lamp shape. How to do it more clearly seen in the photo. You also need to make an octagonal bottom.












Pitch fifth.
We glue four octagon into one whole, after drying, we grind on the grinding machine before getting a form, similar to a vase.








When grinding, rotate the workpiece as smaller as possible, the correctness of the lamp shape will depend on it.

Step six.
It's time to make a leg for a lamp, with which you can adjust the direction of light.
We heat the four small bokeh boards and on the grinding machine twigrating the edge, for this it is best to draw a circle in advance in advance.








In the center of this circle drills the hole, we make it on both sides and on each of the boards.




Then you need to make three small planks, adjacent to both the head of the lamp and to the base, which will also be rounded on the one hand, and for their gluing there will be two small blanks, as in the photo.




We embroine the places of glue glue and press the clamp.






Step seventh.
To regulate the brightness of the light, it is necessary to make a wheel, which after will be planted for a dimmer. Similarly, this wheel make six more such, but to fix the position of the lamp.

In the middle of drilling a deaf hole and glue the M12 thread sleeve with a step 1.25 on the superlocks and screw up to the stop.












To fix the position, three M12 studs in 1.25 increments will be needed, which will pass through the entire fastener of the lamp.



Step eighth.
Now you need to make a shield or the so-called foundation on which the leg of the lamp itself will be fixed. The form of it is also a round, made using a grinding machine.


Surface with grinding machine and on top of the oak thin plate, we glue the circle with a smaller diameter.






For durable gluing, we use clamps, and better at once.


In the meantime, the glue dries can be applied the first layer of oil on the head of the lamp.




Step ninth.
Glue drying, the oak circle was glued, which means we go to the installation of the dimmer. We disassemble its body, we will need the inside the inside, drills the hole in the oak mug and placed on the reverse side of the board sizes, after which it remove the excess material to land the dimmer inwards.

As you know, the thing created by your own hands can become a decent decoration of any interior. Moreover, the more such designer and cozy items, the more interesting and color looks color. For each room of your home or apartment you can create desktops that will become an excellent decoration. And for this, you can use the fir-handed materials and very often those that are initially difficult to submit to the role of this functional and necessary instrument.

Where to begin?

Of course, first you need to think about the design, but we will return to this issue a little later. In the meantime, we define how to make a desk lamp from what we have at hand. We will use the following elements and devices:

The basis for the lamp (it can be a piece of plywood or DVD drive);

Frame from old lampshar;

Tube (it can be any);

Various adhesive compositions;

A piece of cable;

Jewelry for the base;

Switch, fork, cartridge;

Material from which we will prepare lampshade;

Aerosol paint.

Desktop Lamp Scheme

The classic desktop lamp consists of several parts. First, it is a base, a column and in this capacity, it is quite possible to use a glass or lamp chill, for example, from the fabric. It has a switch that is located on the power cord or on the basis, sometimes they are mounted on the base. Depending on the purpose of the lamp, it can have a different design:

  1. A classic lamp that is used to illuminate the workplace. The diffuser here is a glass ceiling or textile lampshade.
  2. The device on the clamp is attached to the table. The column of such a lamp is flexible, that is, you can tilt it as you like. Plafond - opaque fool, which focuses light in one direction. An ordinary or LED is used as a light source.
  3. The dimmer lamp is the ability to adjust the brightness of the light source.

Implement ideas

So, the details of which are made the simplest hand, we have prepared. Now we take glue, base and tube and glue them with each other, for example, with the help of paper or the old newspaper. Yes, do not forget to do the hole at the heart - the cord will go through it later. We give the design to dry, after which we start to decorate our tube.

To do this, we use anything: beads, buttons, beads, bows, figures from kinder surprises and much more. Thanks to this original and at the same time, simple decorations, your lamp will look very non-standard, and therefore it will be possible to transform the interior. The most recent task is to cover the paint lamp. It is best to choose compounds in which there will be no toxins, as well as those that quickly dry. After the device is dry, you can do the manufacture of lampshar.

Lamp from the old vase - fresh ideas

To create your own hands, it is not necessary to look at some designer ideas or strive for effect. It is enough just to take an old vase and make a lighting device based on it. So you will immediately kill two hares: on the one hand, give a new life of an old thing, and on the other, decorate your house something unusual.

So, we will need the following components of the future instrument: the old vase, the cartridge from the old lamp with the holder or holder, for example, from the traffic jam. As the basis, a piece of foam, which inserts the reinforcement is completely comes. It must be thicker to pour epoxy resin, not forgetting about compliance with the safety rules, since this composition allocates harmful substances. Of the prepared materials, a design is created, which is inserted into the old vase. Now it's small - to make a lampshade.

Abazhur - Case Crown

Probably the basis for creating a lamp can be any. But with the help of the lamp, you can change the appearance of the lighting device at least every day. In addition, this element is created easily and easily and again of the materials available at hand. You can perform the design in a variety of stylized directions, but it is important that the table lamps are made, with their own hands, harmonized with the surrounding space. What is the way to create a lampshar choose?

First, the most optimal option is to make a ceiling of the same wallpaper that is saved room. To do this, we take the wallpaper and cut off from them a strip of a wide slightly larger than the label. Then you need to gently glue it to the lamp to the lamp, while it is important not to break it and not to remember. We give time to dry, after which you can safely put on the product on the lamp.

Secondly, the tissue lampshade is popular. It is very simple to make it, and if he wants, it can always be removed and replaced with another type. It is created such a lampshade for the same scheme that is given above.

Children - all the best

As you already understood, to create a desk lamp, it is not necessary to be a generator of ideas and thoughts. It is enough just to show a fantasy. Modern children's desktop lamps are characterized by the brightness of the design, but you can slightly change their appearance and make them more interesting. For example, those who know how to handle cloth can make the original lampshade lamp in the style of Patchwork. In addition, this technique can be implemented somewhat differently, for example, to make the basis for a lamp from children's toys - cubes, puzzle, or decorate the lamp toy toys from kinder surprises.

For the Girl, you can use more romantic drawings and decorative elements. For example, lampshade, richly decorated with satin ribbons, bows, beautiful buttons or an interesting applique, accurately will like to taste cheerful fashionmented.

Original designs

And now let's look at how unusual can be a table lamp. With your own hands (the photo confirms) you can make it very and very throwing, spectacular and memorable. For example, if you have an old globe, it can be safely adjusted under the original shape of the lamp. By the way, this one can safely be given to avid travelers - it is accurate to appreciate.

But the needlewomen probably stores a huge number of balls of threads of many different colors. You can connect a beautiful and bright case and put it on the lampshade. And you can simply add the tissue dome using original related ornaments. Such a lamp will give the room with the facilities and create a favorable situation for the pastime.

Many are laughing, but in the help of originality, almost everything can be used. Suppose, plastic dishes in the form of forks, cups, spoons, wand-umbrellas for cocktails. To create a non-standard lamp lamp, we need a balloon to which we glue all this plastic and cheap good. By the way, on request, you can paint it with acrylic compositions - so your lamp will shine new paints and will look very original!

What is the result?

Thus, ideas for creating a desk lamp at home is very and very much. Choose the way that most suits you in terms of style and constructive solution. After all, fresh ideas in the interior are the easiest way to update it. And this method is profitable, since it is possible to create original lighting devices from what is in your storage room.

Lighting is the most important component of the interior. It is from the lighting that the comfort of the comfort of our dwelling depends. The game of light and shadow allows you to beat the winning moments of the interior and take attention from unsuccessful moments. And also - lamps, lamps, chandeliers and lamps create that atmosphere that we call the "house." Make a dwelling only "your", personal, individual will help unique lamps and the best way - to make lampshade with their own hands. Homemade Plafones and lampshades are the horse, which will allocate your home from others.

Safety words

In the manufacture of lamps, lamps and chandeliers in industrial environments, the minimum distance from the "body" of the lamp to the materials is pre-performed. It depends on the distance from the power and thermal radiation of the lamp and on the type (flammability) of the material from which the ceiling / lamp shade is manufactured. At home, it is unlikely that someone will bother with such calculations. And in order not to create a dangerous situation, you should adhere to certain rules.

And in general, making a lamp and installing it, in the first few days, pay attention to whether there is a ceiling. Heating is considered to be any increase in temperature above the environment. If the ceiling is felt like "warm", change the light bulb into less powerful. Check again. So as long as the homemade lampshade will not warm up.

Where to get a frame

If you want to remake the old lamp, the lamp, the brain, whose old lampshade has come into disrepair, you can simply use the existing foundation, having funned the old material. Before starting work, look good for the framework, if there is a rust somewhere or damaged coating, can it stand everything and paint again? At the same time, the color can be changed. If there are no old frames, you can buy an inexpensive lamp (in the store or on the flea market) and make the same operations with it. Not bad lampshades can be done from baskets for garbage. They are wire, there are plastic. The main thing is to find suitable in shape and size. Then you make a hole under the cartridge. Next - it's a decoration / trim, and here the sea options.

If this method is unavailable, you can make a lamp shade without a frame (there are such) or make a frame yourself. Material for making frame for lampshar do it yourself. It is: wire, wood (wooden or bamboo sticks, cut specially elements), plastic bottles.

How to make a frame for homemade label from wire

Wire for a lamp frame is needed aluminum or steel. With aluminum work easily, but it is easy. This is not very important when the lampshade is already exploited, but this fact must be taken into account during operation: you can spoil the form. On the other hand, such plasticity allows you to easily and simply make changes to the form. So the option is not bad. Aluminum wire can be "mined" from electrical cables. We will have to remove the protective shell and can be used.

Stall wire more elastic, so it retains the form well. It can be searched in the construction market. Work with her more. It is desirable that there were strong men's hands nearby.

In addition to the wire for work, powerful plugs and passage will need. The lamp shade usually consists of two rings and connecting their racks. From the size of the rings and shapes of the racks depends on the form of the future lampshar. Questions may arise by the number of racks and ways to fasten them. The number of racks depends on the size of the rings and how much "round" you want to make a lampshade. The more racks, the more "smoothly" the fabric will fall. So choose to you, but the optimal distance between the racks along the lower circle is about 5-6 cm.

Receptions for creating a wire label

Molding methods The stack to the rings of the lampshar depend on the thickness and type of wire, as well as from your tools you have. The easiest - to make a small hook on the end, then clamp it tightly. And so that the ring does not slide right-left, pre-wire in the place of attachment to treat sandpaper with large grain. This is an option for thick aluminum wire. If the wire is steel, with a diameter of 1.2-2 mm or more, the best way is. Wirestone can be cut and wind around the ring or also make a hook.

If you make hooks, wed up the wire, the appearance is far from such an ideal, like factory frames. But this imperfection will be covered by the lampshade itself. If she is still worried, find the ribbon of suitable color (usually pick up the aboire color) and carefully wrap the resulting frame. Will be much better. The ribbon can be labeled with PVA and, wet, tight, twice behind the turn, wrap the frame.

From wire mesh

If you can find a thin wire mesh, you can quickly make an almost perfect cylindrical plander for a flooring, a table lamp, a night light, a ceiling for installing a candle, etc. Total and it is necessary that cut off a piece of mesh of the desired length and width, roll into the ring and fasten the wires, wrapped them around the racks.

So that the grid does not straighten up, cutting off the piece, cut the long free ends from both sides. They will fasten the cylindrical shape. And the imperfection of the upper and lower rings can be masked with the ribbon of the desired color.

From five-liter plastic bottle

An interesting form of lampshade can turn out of a plastic bottle of large litter. There are bottles of 5-6 liters and even on 10. Here you can use them. From the tank, cut off the tops go to the bottom - depending on what you like more. In the cut part we make a ring under the cartridge. If the upper part is cut, the neck can be used for some cartridges. For those more diameter, it will have to cut.

Then cut out extra plastic, forming the rim and racks of the ceiling. To not be mistaken, you can pre-draw all lines with a marker. Cut will be easier. VCE elementary. Next we just decorate. And yes, cut plastic necessarily, otherwise there will be no warm air to go.

We make lampshades on the frame

Options for how to make the case of the lampshar sufficiently:


From tapes

The easiest and fastest way to transform an old lamp shade for a flooring or desk lamp is to use ribbons. Need a frame or lamp shade in the form of a cylinder. It can be "naked" or covered with cloth. If you use a "naked" frame, the light will break through the slots, which will create interesting light effects, but the lighting will be inhomogeneous. You are uncomfortable to read with such a light - this is an interior solution. If you need smooth lighting, first cover the frame to the cloth. It can be the same color that the tapes, on a couple of tones darker or lighter, can be contrasting. It all depends on your desire. And remember that the darker there will be a cloth, the smaller the light skips the lampshade.

Take the tape with a width of 1-2.5 cm. I fix it from the wrong side of the lampshar with the help of PVA glue, additionally fixing the pin. If we took a wire frame without fabric, fastened to the upper or lower line (you can sew your hands, you can use glue). Then we start wrapping the entire frame, from top to bottom, placing the ribbons close to each other, but without an adhesion.

Having finished the circle, we turn the ribbon to 90 °. Fix in this position (needle with a thread or plow glue, glue from the gun, fixing the temporarily pin, pressing the clothespin). Further ribbon we skip under the first ribbon, pull out, put on top of the second, then stretch down again, pull up through one tape. So, gradually, we create a weave, filling the entire lampshade.

Alternatively, you can skip two vertical tapes. But then it is necessary to ensure that each next row is shifted by one cross. Then it will turn out another type of weave. Such a lampshade is ideal for flooring, as it will go down the light, the dispersion through the walls will be small.

In this embodiment, the tapes may be the same, can - one color, but of different textures, may differ on a couple of tones or be contrasting. In a circle, the tape can be allowed solid, and it is possible - after a certain distance. If you find a wide ribbon and impose it with the overe, then there will be no horizontal at all. And if you use a braided or twisted cord (on the bottom photo on the right), we get a completely different type of lampshade. So only this technician finishing the lampshar gives a lot of options.

Briefly imagine ideas. There are many options for how non-standard ways to make standard frameworks for lampshades. The first method was already voiced: you can connect the case on the lampshade on the needles or crochet. Several options in the photo.

Not everyone can knit. It is easier to work with beads, especially if it is glued. You can decorate the old fabric using beads, sequins, beads of different shapes and sizes. Such a "new-old" lamp shade do it in a couple of hours. We pick up suitable decorations, scrub the fabric with PVA glue, stick decorations. To complete the image, you can collect suspensions from beads and beads, which are attached to the lower line, but it is already painstaking work. Although the effect is interesting.

You can sew a new label of fabric. But it is not necessary to make it updated copy of the old. It should be included fantasy! If the lamp or floor lamp stand in the girl's room, the new case on the lampsur can be made in the form of a skirt. Select the style of the skirt yourself. It is interesting to look into the fold. With ruffles and without.

In the boy's room you can use the old geographical map. They are on dense paper. If the paper is not sufficient enough, you first need to stick the card to the cardboard, and then from such a blank glue the lamp shade.

Original plaffers are obtained if the finished frame shakes the threads or ropes. Ropes can be natural. In this case, they are gray, brown beige. You can find fine synthetic colored cords. Of these, it will turn out more "fun" in the color of the product. It is even easier for the case with threads for knitting. They are thin, thick, textured, with a smoothly changing color. In general, mass options.

We take the frame and according to a certain scheme of its soaring. You can start with racks. Each rack with a pigtail (the length of the threads should be 3 times more than the height of the rack). When this work is over, start stretching the thread / rope between the racks. They will need to pass through the pigtails, so that with threads are more convenient to do it with the help of a needle, and the ropes can be turned on and so.

The second option - first empty the horizontally the entire frame, and then lay the rack. The pigtail will not succeed here, you just need to fasten the turns on the rack with a certain slope. This version performed is somewhat simpler, but the "pigtails" look more decoratively.

Homemade beams without frame

Many materials are tough enough to keep the shape on their own and, at the same time, they are enough plastic to make something interesting from them. There are a lot of such homemade lampshads. And almost all of them cost your attention. We only give a part here, the other part will go in the photo section (see below).

From knitted lace napkins

Crochet-knit napkinsome have many and lie in the "honeycomb", as it is a pity to throw out, and they do not know how. There is a very interesting idea - make from them a lampshade for chandelier on the suspension. In addition to napkins, you need a large balloon or inflatable ball, glue for heavy wallpaper (vinyl, silk-screen printing, etc.), brush.

Machine glue according to the instructions, we wait until I fell. I inflate the ball or take the ball, hang. When the glue is ready, on some clean surface we lay the napkin, we wash it with glue, lay out on the ball.

It is necessary to lay out with such a condition that the center will remain in the center. One by one we glue the napkin. It is necessary to lay out so that the edges overlap a little. When all the napkins are laid, once again we wash them with glue and leave up to dry. When the glue is dry, blow the ball or ball (the ball can be pierced if not sorry) and take it out through the hole. That's all, lace abazhur is ready.

In some cases, there are problems with the way ready-made lampshade to hang on the cartridge. The problem is solved simply - take a transparent plastic bottle, cut off her neck, if necessary, expand the hole to the desired dimensions (so that it is tightly put on the cartridge), then cut off the plastic so that it turns out a ring of 5-7 cm wide. This ring is width And from the inside the ball is lining to the lampsuit.

Round rafones from threads

In almost the same technology, you can make round and semicircular stylish plaffones. Choose a fracture color. Their composition is absolutely unimportant - the color, thickness and texture is important. They can be shaggy, smooth, twisted, fond and thoroughly. The appearance depends on this. It is most convenient to work with cotton threads of medium thickness. They absorb glue well and then, after drying, hold the shape perfectly.

You still need a ball or a ball. It will be the basis of the lampshar, which sets the form. The size of the base is as desired. Threads need to glue, for this you will need PVA glue. It is transferred to the container, diluted with water in proportion 1: 1.

You can use another glue. It is important that it becomes transparent after drying. This is WB-29 TYTAN PROFESSIONAL and D2 glue for carpentry work. If you use some of these types of glue, read the instructions.

On the ball or bowl, draw a circle that will be slightly smaller than the lamp cartridge. On the opposite side, we draw a more circumference - it will be the bottom edge of the ceiling. Now everything is ready, we can proceed.

We wash the thread by glue and wake them on the ball in chaotic order. It is more convenient to do this if the glue is poured into the container - you can lower all the modes, and just pull the thread slowly. With glue in a tube, everything is not so comfortable: it is necessary to miss areas length up to meter, wind, wrap again. Time leaves much longer. This is if used not pva. But the products are obtained more rigid and do not sag, do not change the form over time, as it can happen to the nietary lampshades on PVA.

When winding threads on the ball, diligently go around drawn circles. If accidentally climbed to the "Forbidden territory", simply put the threads, forming a smooth (more or less smooth) edge. When the threads are completed or you decide that the density is enough, the process can be stopped. The edge of the thread is refueling between others. Everything. Further, the ball with wound threads once again we wash the glue (PVA can be poured) and leave to drying (at least 2 days). To do not ride the ball, we find a bowl or a saucepan and use it as a stand.

The last stage - blow the ball or ball. If the ball has nipple, press it with a thin wire, releasing air. Having embarrassed the ball. On this, everything can be traded inside the lamp and test the lampshade.

The technology is the same, but the appearance is very different ...

According to the technology described above, you can make not only round beams. Rectangular, triangular, trapezoidal. Choose the foundation that is easy to remove, wind the thread moistened in the glue, braid, even stick, newspaper tubes, etc. After drying, you delete the foundation and so, you made the lampshade with your own hands. A couple of examples in the photo below.

And you can also use sticks .... Only the ball also wrap the food film and use the PVA not glue, but a transparent joiner

This is a pasty polymer clay in a tube, which was applied to a package from under milk, then dried and the package was removed ...

Creative homemade beams for lamps, lamps and chandeliers

Just the diva is given, from which only people do not make beautiful and unusual things. Plafof from a cup, grates, bottles, beer or glass jars, metal parts and rings from beer cans ... it seems you can use everything ...

Abazhur from the old sieve ... stylish

Candlesticks turn into a lamp ... can be without landscair

In life, you will not say, but these plafones are made of hooks, which open metal cans for drinks and canned food ... If you paint them, it will be even more interesting

Do not know what to do with granny crystal? Make plafoons from it ...

If you want the ordinary metropolitan apartment to resemble an externally unique place in beauty, then in order to achieve this, you can use one of the most popular ways to date.

Some invite home designers, and someone just takes the initiative to their own hands and is looking for how to make a lamp with their own hands to quickly and easily transform space in the apartment at their discretion.

Of course, in order to proceed with work, in any case there will be a certain amount of different undergraduate material, as well as certain knowledge in the assembly and subsequent installation of electrical appliances.

If you did not have to face earlier with the last earlier, then you should not get upset immediately, because absolutely all the rules can be found in free access on the Internet and there is nothing difficult in them.

Basic principles of loyal lighting in the room

Using absolutely any lighting device must first meet the main principle - ensuring accurate access of light on a certain in advance space.

Where and how the source of lighting is located, subsequently will definitely affect the overall picture of the interior perception of the room.

At the same time, if you see the photo of the lamp, then the following goals become obvious:

  • Achieve maximum working atmosphere;
  • Create an interesting decorative effect for rest;
  • Focus on a certain part of the room;
  • Light locally space required, for example, exclusively for personal needs.

Thanks to the installation of a desk lamp, it is fairly easy to achieve high-quality lighting in a particular place.

What color gamut will be fashionable this season?

Of course, the lamp lamp is played a special role in the external transformation of the room. For example, if the room design was originally made exclusively in dark shades, then in order to slightly revitalize the general view of the room, for example, to make that the table lamp will be bright green.

Another interesting way to give a room of originality is the coloring of the simplest plafone in interesting lines and even geometric patterns.

This option most designers are advised to be used if the initial room is performed in sufficiently warm colors. It is worth noting that this option is not advised to be used in children's rooms, since the lighting in any tone will be more familiar to them.

Speaking of exceptionally neutral color solutions, especially allocate various monochrome shades, as well as the color of the sea wave, gold, shades of pink color, is particularly distinguished. Any of these colors can raise the mood literally in a few minutes.

Sequence of actions when creating a lamp

Despite the fact that many are confident that the lamp is extremely difficult to make lamp, in fact, only a few simple items will be needed to work, which can be purchased almost in any store and, in general, the creation of a lamp is not distinguished by complex moments in the work.

The first thing to do is be sure to make a detailed plan. This is necessary in order to be a clear representation of how much the amount of material goes further on the installation of electricians.

In addition, it is necessary to make measurements in the room, namely, to find out how much the distance from the location of the device to the point where in the future it can be connected to the network. It will also have an impact on how much money will have to spend.

It is also important to especially take care that the assembly process and the subsequent installation is fully safe.

If you assume that work in any case will necessarily concern direct contact with various chemicals, then you should cook apron, gloves with glasses, as well as forced hood.

Note!

Safety measures are definitely not something worth neglected because when creating a lamp with their own hands, the process should deliver extremely pleasant emotions.

Photo lamp do it yourself

Note!

Note!