Homemade airbrush from the syringe - an excellent assistant in the farm. This invention makes painting a completely simple process. You can make a homemade airbrush at home, because everyone has the opportunity to buy it in the store, especially since the cost of the airbrush is high enough. It will not be worse than purchased. In order to make it, do not need any special skills or skills, and the components of the airbrush details will be found in any house. You can make a spray spray from the syringe in two ways: without a kraskoraspylitel (this method is very simple) and with a paint-sprayer (more complex).
What is a airbrush?
The airbrush is the same pulverizer (pneumatic tool), which is designed to spray the coloring agent. It is used in many spheres of life, but due to its high cost folk crafts Already learned to make an airbrush with their own hands.
Back to the category
The first method (airbrush without a kraskoravitel)
First of all it is necessary to collect all required tools. For the manufacture of this type of airbrush, you will need:
- one-time syringe and needle from it (its volume depends only on the wishes of the wizard);
- clip;
- a thread;
- clamp - scotch or tape;
- small paint container.
The needle needs to be removed and heat on fire so that it can be separated from the plastic basis. From the syringe you need to remove the piston, the clip must first make it smooth, and then bend it at an angle of 90 °. Tightly connect the thread one side of the clips and needle. Then, with the help of a tape or the isol, fix the second side of the paper clips and the case. Moreover, it is necessary to fix the design is needed near the opening to which the needle was worn. Install the tip of the needle is needed so that it is in the center of the nozzle syringe.
After that, it is necessary to dissolve paint so that it is liquid, in a small container. Airbrush Take in your hand, omit the needle into a container with a coloring matter and blend strongly into a wide nozzle.
Such airbrons are called in common "Rotoduvami". In order to make such an appliance, you will need 9-11 minutes and minimum devices.
Back to the category
The method of the second (airbrush without paint sprayer)
This method is identical to the method described above, it differs only in several details.
For the manufacture you will need:
Position of the pulverizer: A - walls, b - ceiling.
- rod from gel handle;
- disposable syringe + needle;
- cut rod ball knob;
- glass or plastic bottle, container for painting emulsion;
- termocles.
The entire process of collecting an airbrush occurs in several stages:
- writing part of the handle cut the cone;
- the sharp part of the medical needle cut off;
- needle to pre-dip in the thermocons and insert into the cropped rod so that its tip is visible from the metal part of the rod;
- top part The syringe is attached to the bottle (in the case it is necessary to insert a rod with a needle);
- in the lid make 3-4 air access holes;
- the distance between the tip of the needle and the pen can be determined by an experimental way.
One of the advantages of this airbrush is a simple reservation reservoir.
Back to the category
Airbrush with paint sprayer
In order to make a more convenient homemade airbrush, you will need such details:
- pens (3 balls automatic, 2 gel);
- pencil;
- metal empty bottle (you can take a bottle from cosmetics);
- syringes (2-3);
- firm wire;
- bolts 2 pcs. 3 mm;
- nipple;
- small needle - 2 pcs;
- glue.
First of all, you need to collect the cartridge and the needle of the needle. It is necessary to make it from the syringe, the gel handle rod, the springs of the fountain pen and the bolt. From the housing, extract the piston, lower the spring inside (it should be near a thin nozzle), to make a hole in the rod and insert a bolt, and they must be perpendicular to each other. This design is further inserted into the housing.
In the case of the ballpoint handle, it is necessary to make a rolled knife with a hole from two sides: one less and more round (about 0.5 cm), the second is greater and longer (about 2 cm). Next, the segment of the wire must be bent into the focus of the trigger. Suitable for the diameter of the wire needle heat and make two holes in the housing for a bent wire, insert it into the case.
The next step is to prepare 4 segments of the wire 6 cm and bend them at right angles. With these segments, the air housing should be fixed, or rather its valve (manufactured from a piece of ballpoint case).
Then you need to insert the housing that holds the needle directly into the crashpult. It should be inserted without special efforts. The length of the gel handle rod is selected so that the rod is running into a bent wire, and the spring was compressed. To connect all parts you can use epoxy resin, Termoklay or ordinary superchalter.
Next you need to do air valve Aerograph, it will consist of a syringe without piston, needles, springs, cutting tube from a cylinder (air freshener), nipple. All items must be connected by pre-processing glue.
For the trigger, you will need an antenna, a piston hat. It is necessary two sections of the antenna to connect with a hat, and insert insert a match with glue already applied to it. All items also need to be labeled with glue so that the design is strong.
In order to make a paint sprayer for an airbrush, you need one syringe, the iron part of the medical needle, part of the rod with an iron tip, an air hose.
The tank for the coloring emulsion will be a canister from under deodorant, or rather its upper part that needs to be cut off with a knife.
When all the details are interconnected, the paintopult can be finished. Make it easy and not long, most importantly - to have a desire. But if you hurt with a complex designer, you don't want to eat, you can quite use the first and second way. They are not spent so much time, and the items for their manufacture will be available in any apartment or house.
There is another way to make an airbrush with a deodorant sprayer sprayer. Moreover, the empty spray can act as a spacing for soft scattering of paint or any finely dispersed chemical substance. For manufacture need:
- empty spray;
- large on the tank syringe;
- vinyl tube with a diameter that will correspond to a small nozzle;
- compressor for creating pressure in the cylinder;
- gloves.
From a deodorant can be removed plastic valve. The syringe is to wear, as close as possible to the base, the vinyl tube and cut it in such a way that it can be in the future to put on the nozzle of the syringe, but so that the place is left to press the valve of the canpon (that is, the length of the segment of the vinyl tube should turn out to be approximately 0 , 5 cm). Score liquid paint and connect the segment of the vinyl tube with a canister. In this method, the syringe acts as an element to refill the paint spray. In order for the paint to get inside the canister from under the deodorant, you must click on the slot of the balloon and then on the piston of the syringe. The volume of refilled paint is easy to calculate, it is enough to view the volume of the canister and the tank of the syringe. For example, the volume of the spray - 150 ml, the syringe is 10 cubes, it means that it is necessary to pour 5 paint volumes to the cylinder. It is very important between refills. Do not forget to press first the valve of the cylinder, that is, to close it, and only then remove the syringe.
The adapter, which connects the cylinder and compressor from the plastic cover of the medical needle. In the sealed part of the case, it is necessary to make a small hole, and insert the open part into the compressor tube. Next, turn on the compressor, put on the adapter to the can, press on its nozzle and fill the air (on 150 ml cylinder - approximately 2 kg of air). Before painting, put on a plastic spray bottle and shake it.
As the basis took the same sleeve. I wrapped three types of threads to it so that everything is fluent in the syringe. Then she cut out of some garbage, like foam rubber, insert into the sleeve. Three different-caliber needles stuck there and stuffed the sleeve inside. There is no photo, but a couple of pin is still calmly closed.
The syringe has half rooted nose. Boiled him lighter and flattened about the blade of the knife. From the other end of the syringe cut off the extra "ears" and also neatly attached a lighter. Piston rooted. Put in it with a wire hole and handed it through it a drop-down thread. It turned out a cork on the rope. So that she was not lost, she took a thread scotch for the syringe. The syringe itself wrapped the Kapron thread so that it was. On the bottom of the syringe laid three small buttons, then the sleeve with threads and needles and plugged all this business cork. Beauty!
Now I don't remember exactly how many meters wrapped. Thin approximately 20 meters, Kapronova 6-10 meters. In any case, enough for the eyes, and there is almost no weight.
In my opinion, it turned out not bad. Everything is quite compact and hermetically. Since small scissors lie in the first-aid kit, and attached and attached this sewing set.
Syringes are there different sizes (Even at 150 ml.), And it is possible to choose the container under your needs without problems. You can and nazi all sorts of folding and hooks fishing and spices, but you never know what else? It seems to me that it is a little more convenient than sugar and coffee fall asleep into a cocktail tube. Containers are light, sealed, compact, reusable, cheap and not long.
As an example, a couple of my containers. 
In a small (10 ml.) Syringe poured salt. I still do not need a lot with you, but just in case it is enough.
Twenty-cubic syringe placed 7 hunting matches and chirkash glued to a piece of wooden ruler. 
When you buy a syringe by 50 ml. I will make a container under sugar. We and I just have enough tea to drink and a bit will remain. It will be easier to be, than to carry a full jar with you and the place in the bowler will be free.
I hope the note will be useful. Tips, offers, additions and criticism are welcome.
In this material, you will be presented with a way of making a simple pneumatics from syringes.
So, we will need:
- adhesive Pistol;
- juice straw;
- stationery knife;
- 2 large syringe.
We take the first syringe and cut off the nose at the very reason.
Next, it is necessary to do the hole between the marks 5 and 10.
Now the spout, which we cut off at the very beginning, need to be glued to the hole. It is necessary to do this extremely carefully to inadvertently do not stick the hole.
Next, take the second syringe. It must be glued on the place where the spout of the first syringe was. According to the author, normal connection It will pass the air, so it is necessary to use glue for better sealing.
Pneumatics is ready. It can be used in two ways: either to glue the tube and shoot with balls, or do without a tube and shoot the cartridges made from the needles.
With the first option, everything is clear, so we move on to the manufacture of cartridges from the needles. It is done very simple. We take a needle and put it on any syringe.
We stick the spout of the needle into the included and hot adhesive gun and pull the piston, sucking the same amount of glue.
After some time, the glue will freeze and closes the hole on the needle, not allowing air to leave it.
To shoot out of the homemade pneumatics, you need to wear a hermetic needle on the spout of the syringe and thaw the piston of the second syringe. Next, repent the piston of the first syringe so that it closes the hole behind the needle and davir on the second piston. Thus, pressure is created. For the work of the shot, you just need to release the piston closing the hole.
This is a very interesting and simple toy rocket. Any teenager will be just delighted with the game with her. I personally have a rather adult, and then I will gladly launch a rocket from this amazing design.
A pair of ethyl alcohol serves fuel for rocket. The rockets are torn in the air with a perky cotton, which looks very impressive.
Need for the manufacture of rocket
I will make a missile from four rockets, so it is listed below to multiply four times. You can make one rocket.- Disposable syringe. I took 60 ml.
- Used lighter with piezoelectric.
- The wire is two-housing 1-2 meters long.
- Small planks for a stand.
- Pistol with hot glue.
- Soldering iron, stationery knife, ruler and other accessible tool.
Making a toy rocket installation
We take a lighter and wonder it, in order to pull the piezoelectric element, which generates a spark - the discharge of the ignition gas.
Pull the piezoelectric element. This is the high-voltage generator itself. The wiring is one contact, and the second is a brilliant cap from below.
We take the wire duct. It is advisable to choose with thicker insulation.
Connect to piezoelectric.
All then insulating the tape or better as I am a heat shrink.
We take two needles from the syringes. Here I want to warn you and offer either throwing the edge of the needle nadfil or just bite off the floor of a centimeter with cliffs. It must be done necessarily, since during the game the game you can hurt.
Connect the wires to the needles. These will be electrodes that will be inside the rocket.
Shipping for reliability. But this is optional.
We take a syringe and take out the piston.
Remove the rubber sealer from the piston.
Soldering iron make holes in the piston.
Insert our needles-electrodes into these holes.
Pour hot glue for sealing.
Rubber seal take.
Sut off the stationery knife top.
Dress up on a modified piston with electrodes.
The hole of the cylinder is poured with hot glue. It is no longer needed.
Cut a syringe cylinder skirt.
Take hard cardboard or plastic. And cut out of it here such stabilizers of the rocket flight.
Bend a little retreating.
You need four pieces per rocket.
We glue to the cylinder.
We collect a rocket.
I made four such rockets.
Affairs Stand under the whole thing. I took a rectangular plank and drilled two small holes in the middle of the second half. A little later you will realize why.
Next, we take the second plank, but already smaller. Drills in the center Hole for wires. We glue with hot glue. See photo.
We glue all the rockets.
Rearly fix the wires with a nylon screed all four wires.
The remote control is also a table with a glass elements glued to it on hot glue.