We will send the material to you by e-mail
Properly executed facade decoration of a private house fully meets the basic requirements. It protects the walls from external influences, insulates the house, and is a great decorative decoration. In today's material, we will present the most common options for exterior home decoration, photos that allow you to evaluate the decorative features of different materials, and a comparative analysis of the cost of various coatings.
A harmonious selection of finishes ennobles the appearance of the house
The basic requirements for the finishing of facade surfaces are regulated by the Code of Rules 71.13330.2017. On the basis of this document, it is prescribed for fixing facing boards requiring an adhesive layer to use materials in the form of mastic or glue of class C1 (on the lower floors) and C2 (above the first floor).
If the house is finished outside with natural stone, then the slabs are first washed and dried. For artificial materials, additional moisture is not required. When the area of the board material is over 900 cm², the adhesive solution must be applied both to the wall and to the wrong side of the material. When using artificial slabs or natural stone with a thickness of more than 12 mm, fasteners are installed.
Related article:
wood siding
Being the predecessor of all other types of similar finishes, wood siding has not lost its popularity. For the manufacture of modern products, the wood pulp mixture is pressed when heated, which makes the panels durable. Additives are added to improve performance. Raw materials are preliminarily cleaned of harmful impurities and resins, which makes wood siding an environmentally friendly material. The coating from it, thanks to the natural structure, looks cozy and natural.
Among the shortcomings, the need for periodic treatment with compounds that protect against fire, mold and repel insects is noted. Also, wooden cladding requires painting, as it periodically fades in the sun. It is not recommended to sheathe the walls of private houses made of foam or fiberglass with wood siding.
metal siding
If we compare metal siding with analogues, then it is the most resistant to natural influences, has a service life of 30 years or more. The material is durable, withstands shock loads well, does not become brittle when heated and cooled. All dirt is easily washed off with a jet of water from a hose. Metal siding is resistant to decay, it will not be damaged by rodents and insects. This material is fire resistant, does not melt in the presence of an open flame nearby. Under the influence of sunlight does not fade.
The disadvantages include the possibility of rust due to exposure to moisture, higher cost. Cutting requires a special knife, and installation cannot be carried out without professional skills. When fixing the cladding, installation is mandatory.
Sandwich panels
Due to the three-layer structure, which includes a metal or polymer shell located on both sides, and a heater between them, sandwich panels have excellent thermal insulation qualities. In the role of insulation, or polyurethane foam is used.
This is a worthy material for finishing the facades of private houses, the positive characteristics of which are quick installation, low weight, good sound insulation, and environmental safety. Affordable cost is an important factor. After proper installation on a frame (wooden or metal), sandwich panels serve flawlessly for a long time.
The downside may be the possibility of freezing of the joints if the installation was performed with violations.
Ventilated facades
Multi-component ventilated facades protect the walls when the temperature drops and extend their service life. They are a system with the presence of special gaps that provide ventilation of the insulation. It is recommended to use galvanized or aluminum profiles for the frame.
The advantage of ventilated facades is a long service life of at least 50 years. In winter, they save heat well, are non-flammable and environmentally friendly. With temperature differences, cracks do not form on the surface. Simple installation methods are attractive, which can be carried out at any time. If necessary, the lining can be easily dismantled.
The disadvantage of a ventilated facade is the possibility of condensation between the wall and the insulation if the installation was carried out illiterately. From this, the walls begin to freeze through, and moisture forms on them, which reduces the service life.
Modern cladding of the facade of the house, which material is better - comparison of options
The variety of options for finishing the facades of houses with modern materials complicates the choice, so it is important to first analyze their range and decide on priority criteria.
| Material name | Key Benefits | disadvantages |
|---|---|---|
| Plaster: Mineral; acrylic; silicate; Silicone. | Aesthetic appearance breathable coating | Potential for mechanical damage |
| A rock: Natural; Artificial. | naturalness Environmental Safety High resistance to external influences | High price The need for installation skills |
| Facing brick: Clinker; Ceramic; Hyperpressed; Silicate. | Safe frost-resistant With high decorative qualities | Need a solid foundation Careful docking |
| Porcelain stoneware | Excellent durability Resistant to any weather conditions Durability | Significant weight High price |
| Ceramic facade tiles | Good decorative qualities, durability low price | The need for careful ground preparation Must have styling skills Brittleness of the material |
| Decorative siding: Vinyl; Wooden (larch); Metal. | Easy installation low price Nice decor | Some species have a short lifespan. Poor UV resistance |
| Sandwich panels | Environmental Safety Quick installation Good sound insulation Durability | Joints can freeze |
| Ventilated facade | Long service life High thermal insulation performance Available installation | Condensation may form in gaps |
Even a brief overview analysis allows us to draw certain conclusions. More detailed information can be found in the article in the descriptions on specific types of facing varieties.
Harmonious combined facade decoration
If there are difficulties with what material to finish all parts of the building, you can choose different types of finishes, harmoniously combining them. How such an exclusive facade of private houses will look like, the photos below will demonstrate from various angles.
Additional decor can be inserts from another type of material. This technique is more common in order to ensure reliable protection of the foundation and basement.
You can choose different materials for a combined finish. It is important not to create variegation by performing a harmonious arrangement of individual elements. The result is an exclusive design style that draws attention with originality and demonstrates the artistic ability and taste of the owners.
Overview of prices for facade materials for exterior decoration of the house
When deciding how to sheathe a house outside cheaply and beautifully, you should analyze the prices for the most popular facing materials.
| Material name | Price per m², rub. | The cost of turnkey work, taking into account insulation per m², rub. |
|---|---|---|
| Plaster | ||
| Mineral | 350−750 | ˃850 |
| Acrylic | 1600−1905 | ˃2100 |
| silicate | 2600-2615 | ˃3100 |
| Silicone | 2406−3900 | ˃3500 |
| A rock | ||
| Natural | 1400−2750 | ˃7340 |
| Artificial | 550-2350 | ˃4550 |
| Facing brick | ||
| Clinker | 1250−2650 | ˃2600 |
| Ceramic | 400-800 | ˃1400 |
| hyperpressed | 665-1250 | ˃1700 |
| Silicate | 280-350 | ˃1000 |
| Porcelain stoneware | 630-1850 | ˃3680 |
| Ceramic facade tiles | 958-2350 | ˃1700 |
| decorative siding | ||
| Vinyl | 185 | ˃750 |
| Wooden (larch) | 590-1950 | ˃2000 |
| Metal | 450-600 | ˃1550 |
| Sandwich panels | 600-1800 | ˃3100 |
| Ventilated facade | 1150-1500 | ˃650 |
Among the improved varieties of cladding of the new generation, it should be noted the Russian-made facade thermal panels, the price of which varies from 2050 to 7000 rubles. per m2. Such material is a gas-filled plastic with a decorative surface made of mineral chips or tiles of various colors and textures.
Choosing the right type of finish for your home is a serious job that requires a comprehensive analysis of many factors. We will be interested in your experience, express your opinion, share tips and recommendations, ask questions in the comments.
Article
The question of what is cheaper to finish the facade of the house is relevant for almost all owners of private buildings. After all, on the one hand, I want the cladding of housing to be of high quality and aesthetically attractive, and on the other hand, it is obvious that unjustified expenses in the pursuit of "exclusivity" and stunning appearance are useless. Rare are families who can afford any solution without regard to its cost.
But it is definitely not worth going to extremes, stopping at the most budget option, without an objective assessment of the ability of the selected material to “resist” an aggressive outdoor environment - wind, rain, frost, snow, etc.. Unless, you want to see in practice the effectiveness of the saying "the miser pays twice."
Of course, it will not work to finish the facade of the house cheaply, but it is quite realistic to choose the optimal material, which, all other things being equal, will have a lower price.
Criteria for a competent choice
In order to decide how best to finish the facade of the house and at the same time not lose money financially, it is very important to clearly define the criteria that help identify the advantages and disadvantages of one or another option.
First of all, you should pay attention to the appearance of the finished facade. Of course, the "presentability" of the cladding is a very, very subjective concept, directly dependent on the personal tastes of the owners. However, such parameters of the materials used as:
- number of offered color variations and textures,
- resistance to fading and other visual defects,
- similarity to natural raw materials (if an imitation product is considered)
under no circumstances should it be left unattended. They will help to make an objective impression about the product.
The next quite obvious criterion is the durability of the material. Agree, it will be very sad if the inexpensive facade of the house turns out to be a real headache with the need for annual re-innovation work. If the type of cladding you like has a good service life - know that you are on the right track.
It is no secret that it is not enough just to choose a facade material. It still needs to be installed. The complexity of the task, the presence of seasonal restrictions, the volume of auxiliary elements and materials - all these factors must be taken into account.
And finally, the final cost of the outer cladding. This should include:
- material cost per kilogram or square meter;
- the price of components, tinting, necessary equipment;
- the cost of installation (and, if necessary, preparatory work).
Ceteris paribus, you can safely focus on the final cost of finishing the facade when choosing.
Popular options for exterior home decoration
Most often, owners of private houses prefer facade cladding:
- siding;
- facade plaster;
- block house;
- facing brick - ceramic or clinker;
- facade tiles.
Siding - a good choice or not?
The main types of siding used for cladding the facades of houses are vinyl and basement. Aluminum is rarely used in residential construction. The key advantages of the material are safety, relative ease of installation, ease of maintenance.
And the most obvious drawback is the artificial appearance. And, we can say that this fact almost crosses out all the advantages. In Europe, for example, siding is used only when it is necessary to clad utility or temporary buildings. And although basement siding, unlike vinyl, imitates natural brick or stone, it still “breathes” with plasticity.
As for the service life, siding manufacturers assure that their “children” are able to serve faithfully for 40-50 years. But in practice, this figure is usually much less, since the material is brittle in severe frosts, unstable to deformation, and prone to fading. Cases when it is sad to look at siding after 5 years of operation, unfortunately, are not rare.
When installing siding in the cold season, it should be borne in mind that the material has a high rate of thermal expansion.
average cost
Vinyl siding will cost you about 200 rubles / sq. m. The total cost of such a cladding, taking into account installation and the necessary auxiliary elements, is about 1500 rubles / sq.m.
Basement siding is a more expensive pleasure. The material itself costs an average of 400-500 rubles / sq.m. The actual cost of finishing the house with him is 3000 rubles / sq.m.
Advantages and disadvantages of plaster
Plaster - a coating that can provide the facade with a decent appearance; waterproof, breathable. Depending on the connecting link, facade plasters are:
- mineral (base - cement);
- acrylic (base - acrylic resins);
- silicate (base - liquid glass);
- silicone (base - silicone resin).
The variety of textures and colors of this material is very limited. In the vast majority of cases, such lining must be additionally painted. And the texture can usually be chosen either rough or rustic.
The service life of a facade finished with plaster is 7-10 years. And although plaster becomes stronger over time, it is not resistant to mechanical damage.
Installation subtleties
It takes 6-8 weeks to decorate a house with an area of 150-200 square meters with facade plaster. Surfaces must first be primed. "Wet" processes make the installation of facade plaster highly dependent on weather conditions and the season.
Note! The low vapor permeability of acrylic plaster makes it impossible to use it in "tandem" with such a heater as mineral wool.
Only mineral plaster is “suitable” for a gas-foam concrete base.
average cost
- Mineral plaster. The cost of the material is about 40 rubles / kg. Consumption of plaster per square meter - 3 kg. The total cost per square meter, including payment for installation and all necessary materials, is 2000-2200 rubles.
- Acrylic plaster. The cost of the material is 50 rubles / kg. Consumption - 1.5 kg/sq.m. The total cost is 2500.
- silicate plaster. The cost of the material is 100 rubles / kg. Consumption - 2.5 kg/sq.m. The total cost is 2800.
- Silicone plaster. The cost of the material is 100 rubles / kg. Consumption - 3 kg/sq.m. The total cost is 3000.
Block house features
Block house - a subspecies of lining, with its front surface imitating a rounded log. This material is natural and environmentally friendly, but rather expensive and short-lived. Not fire resistant. Of the flaws in appearance, knots, cracks, wormholes and other defects characteristic of wood are possible.
When buying a block house, you should make sure that it is not "raw" - otherwise there is a high risk that the material will rot.
Important! A block house, like any outdoor wooden surface, needs periodic updating - coating with special protective compounds, etc.
average cost
The price of a block house largely depends on the type of wood. The cost per square meter can range from 400 to 1000 rubles (including installation work and necessary processing - 3000-4000 thousand)
Facing brick - quality and durability
The front ceramic brick is an environmentally friendly material from natural raw materials (clay), manufactured using a special technology. It is frost-resistant, durable, demonstrates low moisture absorption and good sound insulation. Facing clinker bricks are produced in exactly the same way as ceramic ones, but fired at a higher temperature, so that no voids remain in it. Compared to ceramic, it has even better physical characteristics.
Facing brick has a wide range of textures, shapes and colors. With it, your facade does not risk fading. The only possible external drawback is the appearance of efflorescence.
A house finished with front brick will look luxurious for decades. Clinker brick is an example of durability, it is able to withstand more than 150 freeze-thaw cycles.
Facing the building with bricks should be taken into account even at the design stage (the material is laid on the main foundation). Otherwise, additional strengthening of the foundation will be required.
average cost
The spread in material prices is quite large, but, of course, having the status of a leader in terms of durability and quality, facing bricks simply cannot be cheap. Professional brick laying is also quite expensive. Therefore, the average Russian rarely chooses this option for finishing the facade.
A square meter of ceramic brick will cost 1200-3000 rubles, clinker - 3600-4000. A square meter of a finished, beautiful and insulated brick facade will generally require up to 6,000 rubles.
Facade tiles: pros and cons
Facade tiles are a modern and reliable building material. Not afraid of moisture, strong, durable. With high-quality laying - provides an excellent appearance of the house. The service life of a facade finished with ceramic tiles can be tens of years. True, much depends on the quality of the adhesive solution.
Installation of facade tiles is usually not easy. The process becomes more difficult:
- the need for careful preliminary surface preparation;
- the difficulty of achieving straightness of the seam;
- high brittleness of the material before laying.
average cost
Facade tiles, in comparison with bricks, demonstrate the final result that is no worse in terms of quality and aesthetics, but costs much less. The price per square meter of material is 1000-1500 rubles, while the actual cost per square meter of such cladding usually does not exceed 3000.
Really inexpensive decoration of the facade of the house can only become if you do it yourself. As you can see, some materials, at first glance, seem extremely cheap, but in practice, taking into account the cost of all auxiliary elements and the entire scope of work, it turns out that this is not the case. And only if you decide to take on this rather difficult work on your own, you can talk about significant savings.
This video will acquaint you with the rules for installing vinyl siding:
When choosing materials for facade cladding, it is very important to objectively evaluate their "perspective" - how long they will last, how often they will need maintenance and renewal, what investments and how soon they may require.
It will not be superfluous to look on the Internet at photographs of various types of facades, to feel which “performance style” you like best. The appearance of the house should not just be liked - you should be in love with it. It has been proven that this moment directly affects the psychological comfort of staying inside or near housing.
To understand how cheaper it is to finish the facade of a house, photos of various cladding options are unlikely to help, but they will clearly contribute to a clear idea of \u200b\u200bwhat awaits you in the end when referring to a particular material.
Having thoughtfully weighed all the nuances, we are sure that you will be able to make the right decision, which will be optimal for your family, both from a financial and aesthetic point of view.
The question of how to make the facade of the house, and make it unique, beautiful and practical at the same time, is very important. It is almost impossible to overestimate it, because it is the facade that determines the appearance of any house.
The very first impression of the house and its owner will be determined by the successful selection of finishing materials. In addition, high-quality performance of all facing works is important. Facade work refers to work on the implementation of exterior decoration. Therefore, they should be performed after the completion of the main construction work with walls and roofs.
Beautiful facade of the house
It is not difficult to do the cladding of the facade of your house yourself, with your own hands. The main thing in this matter is knowing what to do and how. Well, some building skills must also be present.
Attention: It is worth deciding what is more important for you - time or money. Do it yourself - save money, trust the experts - save time.
How to mount the facade
So, the walls are removed, the roof is mounted, the main concern of the owner of the building is the task - how to make the facade of the house. I want the house to look original, unique and that all the details of the facade are in harmony with each other.
There are many ways to finish the facade, as well as ways to achieve your goals. And one of these ways is to use different options for facade cladding.
There are many cladding options. And the owner of the house is faced with an important question: what to make the facade of the house from. Most often, facade decoration is necessary in cases where the house is built of brick or cellular concrete.
Frame houses are required. If the house is wooden, then the facade is rarely finished. Wood is not the material that needs refining.
So: how to make the facade of the house?
Types of facade decoration
ceramic brick
Cladding with ceramic bricks It is difficult to name such an area of construction, wherever ceramic bricks are used.
In its manufacture, a special technology is used, thanks to which it receives serious advantages:
- Frost resistance which is very important for our climatic conditions.
- durable. The service life is calculated in decades.
- Capable of removing harmful substances. Property of interest: unique ability to remove harmful substances supplied by the environment.
Rainwater contributes to the self-cleaning of facing bricks on the facade of the building. - Facing brick has strength and stability. Atmospheric, short-term mechanical influences do not have any changes in the appearance of the brick.
- Available in a variety of colors and textures.
Clinker tiles
Finishing with clinker tiles Perhaps it will happen that it becomes unaffordable. Among the materials for facade cladding, there is something to replace it, but at the same time, the facade will look like a brick one. Such a substitute is clinker tiles.
She is able to imitate a brick, while repeating its shape, size and color. Everything is exactly the same, except for the thickness. It has all the advantages of a brick, plus it can be considered that the tile is very convenient in transportation and installation. The configuration of the inner side allows you to firmly connect it to any surface.
Stone: natural or artificial
Artificial stone on the facade The facade can also be finished with natural stone. But it belongs to expensive materials and, moreover, is heavy and not very convenient in processing. For this reason, the stone was also replaced in the form of an artificial finishing stone.
And the very concept of "artificial" refers only to the fact that human technology is involved in its creation, and not natural phenomena.
All components of this material are absolutely safe for humans, environmentally friendly material.
Cladding with fiberglass panels
Fiberglass panels that imitate natural stone began to be used not very long ago.
Their advantages include the following properties:
- Lightweight and easy to install.
- High aesthetics - natural stone is reproduced in all details.
- Fast finishing work. This greatly reduces labor costs.
- Fiberglass panels are able to imitate almost all types of natural stones.
- Resistant to temperature changes, resist atmospheric influences, are not affected by fungi and mold.
- Do not lose color under the influence of ultraviolet rays.
- High strength characteristics.
- For many years they are able to retain their properties.
siding finish
Benefits of vinyl siding Represents one of the easy, simple and economical ways of facade cladding. With the help of siding, both the alteration of the facade of the house and the creation of the facade during the construction of a new building can be carried out.
Among its advantages:
- Relatively lower price per unit area.
- Fast and convenient installation.
- Serves as a reliable protection against external aggressive manifestations.
- Does not create additional load on the walls and on the foundation.
- It has high aesthetic qualities.
Attention: When purchasing siding, pay attention to the fact that it is from the same batch of production and make a certain reserve. Otherwise, you can not get into the shade.
The siding can have both a polymeric covering, and a paint and varnish. Polymer is more durable.
Siding is mounted very simply, so it is quite possible to do it yourself without involving expensive specialists. Moreover, the installation instructions do not look complicated. One has only to answer the question: what is the best way to make the facade of the house: vinyl siding or metal.
They have common positive qualities, but there are also differences. In both cases, preliminary alignment of the walls is not required. They have many colors and shades.
Metal siding is non-combustible, withstands severe temperature changes, and has a service life of more than 50 years. Among the disadvantages are the relatively high cost, dents after impacts and the rather large weight of the facade.
Reliability of metal siding Vinyl siding is particularly lightweight, and for this reason can be mounted without the need for outside help. It does not fade in the sun and attracts buyers with a lower price.
The choice of material for the facade is not a very simple matter. The presented photo and video materials can help in this choice. Undoubtedly, you will be proud of the facade of your house.
Choosing the material and technology for finishing the facade of the house should be at the design stage. The modern market offers a lot of different materials, so it will not be difficult to equip the facade in accordance with a certain budget or design idea. When choosing a material for finishing the facade of a private house, two most important factors should be taken into account. Firstly, the house must be in harmony with the surrounding area, look aesthetically pleasing and in accordance with the tastes of the owner. Secondly, the facade material should become a protection for the house, playing the role of an additional insulation and sound insulator, as well as protecting the supporting structures from moisture, sunlight and other negative influences. Not every finishing material will cope with the tasks, so let's focus on the best options.
Types of facade structures
Among other things, when choosing a facade material, it is necessary to take into account what the building is built from, the principle of organizing facade decoration may depend on this. For example, for wooden houses, it is advised to equip a ventilated facade.
It is customary to divide facades into the following types:
Depending on whether there is a gap between the outer wall of the house and the finishing material, the facades are divided into:
- ventilated;
- non-ventilated.
Ventilated facade
Ventilated facades assume the presence of a ventilation gap between the facade material and the wall, or if it is used. The gap is necessary for free air circulation and removal of excess moisture that condenses or leaves the house through the walls. At the same time, the ceiling wall material remains completely protected from all atmospheric influences. It is better to equip such a facade when the walls breathe. involves the installation of finishing material directly to the wall. Sometimes facades are classified simply as ventilated and "wet", although this is not entirely correct.
Now we can move on to materials that are widely used in the decoration of the facade of a private house.
No. 1. Facade plaster
No. 3. Facing brick
Among the most popular materials for facade decoration has always been and is. Of course, for these purposes, not an ordinary building one is used, but a special decorative one, which is called.
ceramic brick
Ceramic bricks, made from clay by firing it, are well known to each of us. Its facing variety strikes with a wide variety of colors and textures, but this is not the only advantage of the material.
Advantages:
- durability;
- environmental friendliness;
- good sound and heat insulation characteristics;
- resistance to temperature extremes, sunlight, fire;
- relative cheapness.
disadvantages:
Hyper pressed brick
Such material is obtained by using shell rock and some special additives by semi-dry pressing. Outwardly, it resembles a ceramic brick, but in many respects it is ahead of it.
Advantages:
- durability and strength;
- good geometry;
- frost resistance;
- a large assortment;
- ease of processing.
The water absorption of such a brick is at an average level - about 5-6%, and the obvious disadvantages of the material include high thermal conductivity, the ability to change color over time and a lot of weight, which affects transportation. 
silicate brick
Facing silicate brick is made from a cement-sand mixture by autoclaving, special additives can be used. Due to the ease of production and low cost of raw materials, silicate brick is considered one of the most affordable materials among other types of bricks.
Advantages:
- high strength;
- exact geometry;
- environmental friendliness;
- good soundproofing qualities;
- low price.
disadvantages:
No. 4. Porcelain tile for facade
Advantages:
- durability;
- the widest range. You can find tiles of any size, color and texture, as well as imitating stone, brick and other materials;
- resistance to negative environmental factors;
- fire resistance;
- relatively small weight.
Tiles can be installed both in a “wet” way and by equipping a ventilated facade. 
No. 6. Concrete facade tiles
The material is produced on the basis of cement, quartz sand, filler and additives.
Advantages:
- durability and moisture resistance;
- strength and rigidity;
- big choice;
- relatively low price.
disadvantages:
No. 7. decorative siding
Siding is one of the most inexpensive, easy to handle and modern materials for the facade of the house. It has excellent decorative qualities, is sold in a wide range, boasts decent durability (up to 50 years), excellent sound and heat insulation qualities. With siding, you can revet any surface and even ennoble a long-built house.
The main types of decorative siding:
- vinyl;
- wooden;
- metal;
- cement.
Vinyl siding
It is made of polyvinyl chloride, can imitate stone, brick, wood and other natural materials. - one of the most popular materials for facade cladding, it is most often used in domestic private construction.
Advantages:
Often the advantages include resistance to mechanical damage, but a strong blow can violate the integrity of the material. Among shortcomings a large coefficient of linear expansion, which must be taken into account during installation, low thermal insulation qualities and the difficulty of replacing a damaged element in case of repair.
Separately, it is worth highlighting basement siding. It is completely identical to vinyl, but has an increased thickness: 3.5 mm versus 0.7-1.2 for conventional PVC siding. Due to this, resistance to mechanical damage is increased, which makes the material one of the best in terms of price and quality for. 
wood siding
metal siding
It is made of aluminum or steel, which are covered with a layer of primer and polymer coating. in private construction is used infrequently due to the high price. Best suited for home cladding steel sheets with a zinc protective layer and a polymer or powder coating.
Advantages:
- strength;
- durability (up to 50 years);
- resistance to temperature extremes;
- incombustibility;
- resistance to any weather vagaries;
- high aesthetics;
- relative ease of installation.
In addition, metal siding is resistant to corrosion due to protective coatings, but if such a coating is damaged, rust should appear. Naturally, it is not necessary to talk about heat and sound insulation qualities. 
cement siding
The material is obtained by mixing and pressing cellulose fibers and cement. Cement siding can replace stone in terms of its decorative and operational qualities.
Advantages:
- high strength;
- resistance to precipitation, sunlight, high and low temperatures;
- fire resistance.
Among cons heavy weight, installation complexity, high cost and insufficiently wide selection of colors and textures. 
No. 8. Sandwich panels
They are a multilayer material consisting of two layers of rigid material (usually metal) and a layer of insulation between them. All this "sandwich" is connected by hot pressing, the surface of the panels can be smooth, embossed or decorative.
Advantages:
Of the minuses, only a high price.
No. 9. Facade cassettes
Metal facade cassettes are widely used today for facing the facades of administrative buildings, but more recently they have also been used in private construction. The material is easy to recognize by its characteristic appearance: these are square or rectangular elements made of metal (steel, aluminum, less often copper) with a polymer coating.
Advantages:
- high reliability and durability;
- aesthetics;
- a large selection of sizes and colors;
- resistance to negative environmental factors and fire.
Metal cassettes can be used for cladding old and newly erected buildings, they are mounted on a frame. The only negative is the high price.
No. 10. New and Undistributed Materials
In addition to those materials that have already become traditional in the field of facade cladding, there are more innovative and in some ways even more progressive. The most interesting of them:
- concrete siding. It is made from cement, sand and dyes. The material has a beautiful appearance and a pleasant rough surface, it is durable, but heavy enough, so it will require reinforcement;
- clinker thermal panels consist of ordinary clinker tiles and a welded layer of expanded polystyrene, and this is an excellent insulation. With external attractiveness, such a finish becomes an additional heat insulator. The disadvantage is the high price;
- glass panels- a popular option for shopping centers and office buildings. For arranging a private house, it is suitable only if you like bold decisions.
The choice of finishing material for the facade should be preceded by a multivariate analysis, including the climatic features of the region, the type of house, the particular style of the site, your own preferences, the material of the walls, your own requirements and preferences. Fortunately, there are plenty to choose from.
How to make a house facade: finishing options
The question of how to make the facade of the house, and make it unique, beautiful and practical at the same time, is very important. It is almost impossible to overestimate it, because it is the facade that determines the appearance of any house.
The very first impression of the house and its owner will be determined by the successful selection of finishing materials. In addition, high-quality performance of all facing works is important. Facade work refers to work on the implementation of exterior decoration. Therefore, they should be performed after the completion of the main construction work with walls and roofs.
Beautiful facade of the house
It is not difficult to do the cladding of the facade of your house yourself, with your own hands. The main thing in this matter is knowing what to do and how. Well, some building skills must also be present.
Attention: It is worth deciding what is more important for you - time or money. Do it yourself - save money, trust the experts - save time.
So, the walls are removed, the roof is mounted, the main concern of the owner of the building is the task - how to make the facade of the house. I want the house to look original, unique and that all the details of the facade are in harmony with each other.
There are many ways to finish the facade, as well as ways to achieve your goals. And one of these ways is to use different options for facade cladding.
There are many cladding options. And the owner of the house is faced with an important question: what to make the facade of the house from. Most often, facade decoration is necessary in cases where the house is built of brick or cellular concrete.
Frame houses require facade finishing. If the house is wooden, then the facade is rarely finished. Wood is not the material that needs refining.
So: how to make the facade of the house?
Types of facade decoration
ceramic brick
Cladding with ceramic bricks
It is difficult to name such an area of construction, wherever ceramic bricks are used.
In its manufacture, a special technology is used, thanks to which it receives serious advantages:
- Frost resistance. which is very important for our climatic conditions.
- Durable. The service life is calculated in decades.
- Capable of removing harmful substances. Property of interest: unique ability to remove harmful substances supplied by the environment.
Rainwater contributes to the self-cleaning of facing bricks on the facade of the building. - The facing brick possesses durability and stability. Atmospheric, short-term mechanical influences do not have any changes in the appearance of the brick.
- The presence of a variety of colors and different textures.
Clinker tiles
Finishing with clinker tiles
It may happen that facing ceramic brick for the facade of the house becomes too expensive. Among the materials for facade cladding, there is something to replace it, but at the same time, the facade will look like a brick one. Such a substitute is clinker tiles.
She is able to imitate a brick, while repeating its shape, size and color. Everything is exactly the same, except for the thickness. It has all the advantages of a brick, plus it can be considered that the tile is very convenient in transportation and installation. The configuration of the inner side allows you to firmly connect it to any surface.
Stone: natural or artificial
Artificial stone on the facade
The facade can also be finished with natural stone. But it belongs to expensive materials and, moreover, is heavy and not very convenient in processing. For this reason, the stone was also replaced in the form of an artificial finishing stone.
And the very concept of "artificial" refers only to the fact that human technology is involved in its creation, and not natural phenomena.
All components of this material are absolutely safe for humans, environmentally friendly material.
Cladding with fiberglass panels
Fiberglass panels that imitate natural stone began to be used not very long ago.
Their advantages include the following properties:
- Lightweight and easy to install.
- High aesthetics - natural stone is reproduced in all details.
- Fast finishing work. This greatly reduces labor costs.
- Fiberglass panels are able to imitate almost all types of natural stones.
- Resistant to temperature changes, resist atmospheric influences, are not affected by fungi and mold.
- Do not lose color under the influence of ultraviolet rays.
- High strength characteristics.
- For many years they are able to retain their properties.
siding finish
Benefits of vinyl siding
Finishing the facade of the house with siding is one of the easy, simple and economical ways of facing the facade. With the help of siding, both the alteration of the facade of the house and the creation of the facade during the construction of a new building can be carried out.
Among its advantages:
- Relatively lower price per unit area.
- Fast and convenient installation.
- Serves as a reliable protection against external aggressive manifestations.
- Does not create additional load on the walls and on the foundation.
- It has high aesthetic qualities.
Attention: When purchasing siding, pay attention to the fact that it is from the same batch of production and make a certain reserve. Otherwise, you can not get into the shade.
The siding can have both a polymeric covering, and a paint and varnish. Polymer - more durable.
Siding is mounted very simply, so it is quite possible to do it yourself without involving expensive specialists. Moreover, the installation instructions do not look complicated. One has only to answer the question: what is the best way to make the facade of the house: vinyl siding or metal.
They have common positive qualities, but there are also differences. In both cases, preliminary alignment of the walls is not required. They have many colors and shades.
Metal siding is non-combustible, withstands severe temperature changes, and has a service life of more than 50 years. Among the disadvantages are the relatively high cost, dents after impacts and the rather large weight of the facade.
Reliability of metal siding
Vinyl siding is particularly lightweight, and for this reason can be mounted without the need for outside help. It does not fade in the sun and attracts buyers with a lower price.
The choice of material for the facade is not a very simple matter. The presented photos and materials can help in this choice. Undoubtedly, you will be proud of the facade of your house.
On demand " photo of interior decoration of houses» found 12216 a photo
Photo Interior Finishing Houses
House design inside. 200+ photos.
Home interior design needs to be taken seriously.
It is important that the chosen style makes it cozy and harmonious. How to choose the style of the interior of the house? In order not to make a mistake when choosing an interior style, you need to decide on the answer to some questions. What interior style do you like and think is the closest? What should be the color scheme of the premises? How many people will live in the house, their age and hobbies?
What functional areas would you like to see in the house? The answers to these questions will help the interior designer to most accurately choose the style and create the interior of the house, in which all family members will feel comfortable. recipe with photo French meat with potatoes in the oven
The cost of a home interior design project. The area of the object. Up to 100 m2. 101 - 200 m2. 201 - 400 m2.
401 - 600 m 2. 601 - 800 m 2. 801 - 1000 m 2. From 1001 m 2. Working drawings. 2000 rub. / m 2.
1900 rub. / m 2. 1800 rub. / m 2. 1700 rub. / m 2. 1600 rub. / m 2. 1500 rub.
/ m 2. 1400 rub. /m 2. Three-dimensional visualization.
Present. Present. Present. Present. Present. Present. Selection of materials. +300 rub beautiful make-up photo step by step.
/ m 2. +300 rubles. / m 2. +300 rubles. / m 2. +300 rubles. / m 2. +300 rubles. / m 2.
300 rub. / m 2.
Finishing the facade of the house with your own hands - from what and how
300 rub. / m 2. Complete interior design project. 2300 1600 rub. / m 2. 2200 1500 rub. / m 2. 2100 1400 rub. / m 2.
2000 1300 rub. / m 2. 1900 1200 rub.
/ m 2. 1800 1100 rub. / m 2. 1700 1000 rub. / m 2. The minimum cost of the contract: happy birthday greetings to a man beautiful pictures 150,000 rubles. Advance payment: 5000 rub. The discount for the full design project is valid until July 1st. How to get an additional 10% discount?
The complete design project includes all working drawings, three-dimensional visualization of all rooms and selection of all materials.
Order a design project. View the contract for the development of an interior design project. House design inside.
Photo from portfolio. Nothing was found matching your criteria. Design of the house inside the house at the address mo, p. Korenevo, kp pearl korenevo, 207 sq. M. 64 photos. 64 photos 64 photos 64 photos 64 photos 64 photos.
Design of the house inside the house at vil. Filino, dnp woodland, pos. Nikolsky lakes, 160 sq. M. 50 photos. 50 photos 50 photos 50 photos 50 photos 50 photos. House design inside the house at mo, Istra district, kp park avenue, 335 sq. M. 90 photos. 90 photos 90 photos 90 photos 90 photos 90 photos.
House design inside the house at mo, pos.
Meshcherino, southern valley, 250 sq. M. 52 photos. 52 photos 52 photos 52 photos 52 photos 52 photos. Show more show all photos. Renovation of a private house inside. The specialists of the foundation group of companies will not only develop a competent design project for the interior of the house with detailed 3d visualization, but also implement it on a turnkey basis in the shortest possible time at the highest level with three-stage quality control.
There are many options for interior decoration of the house. Conventionally, they are divided into three large classes: Redecoration, which involves a slight renovation of the interior, painting or wallpapering, renovation of walls, floors and ceilings, without rough and major work; overhaul, with the demolition and erection of walls, electrical alteration, new flooring, full roughing and finishing work, laying the necessary communications; business-class repair, which involves a major overhaul using complex modern materials, the latest technologies and engineering innovations.
Interior decoration of the house.
Interior design ideas. Wall decoration inside the house can be either complete or partial, which implies some design styles. For wall decoration, they now use mainly decorative plaster, modern wallpaper, all kinds of panels and cladding. Frescoes, pilasters, stucco, friezes and moldings are used to decorate the interior of a house in a classical style.
In modern creative interiors of houses, wall painting, wood trim, clinker bricks and stone decoration are used.
An equally important element of decor in the house is the floor. It can be laid out with plain, combined or mosaic tiles, as well as various types of parquet. In addition, today there are many modern solutions, such as self-leveling floors or microcement floors, which are perfect for designing houses and cottages in trendy styles such as loft, techno, avant-garde, Mediterranean and others.
If the emphasis in the interior is on the walls, then the floor should be decorated in neutral or light colors. If a solid light color scheme was chosen for the walls, contrasting options may be suitable for decorating the floor, for example, black and white floors or floors with metlakh tiles, as well as artistic parquet.
Country house interior styles.
The interior design style of a house is determined not only by its design features, but by the general preferences of all family members living in it, reflecting their character and hobbies. The design of the house inside is better to create, adhering to any chosen style. The design of the house in a classic style will create a feeling of harmony and comfort. Such an interior will always be relevant, because a classic like a “black dress” never goes out of fashion. The interior design option in ethnic style is suitable for lovers of travel and a free lifestyle.
In such an interior, much attention is paid to small objects, elaboration of details and color scheme. Modern styles such as loft, minimalism, avant-garde, contemporary will appeal to young couples and creative families.
For older couples with children, cozy and thoughtful styles, such as Provence, Scandinavian, Art Deco and Neoclassic, are suitable. The interior in eco, country or bungalow style is suitable for decorating the home of nature lovers and natural materials.
The designers of the foundation group of companies can offer many more options for the interior design of suburban private houses - the choice is always up to the client.
Contact the professionals of our studio for a design solution for your home!
Construction »Finishing» Articles »Where to start the interior decoration of the house
Why start home decorating?
Before you start decorating your home, you should at least think about how much work you expect.
Of course, if you don't finish the first time, then the work will be much less than if you finished in a new house.
Here is a short list of templates that will help answer the question - where to start the interior decoration of the house:
- it is advisable to start the interior decoration of the house from the furthest from the entrance to the rooms, not to take it immediately for all rooms;
- In the process of painting or masking a surface, remember that it is best to do it from top to bottom;
- Areas that don't need embellishments are best covered so they don't need to be cleaned.
It is best to carry out internal processing only if all work is completed when installing load-bearing partitions and accessories.
All doors, windows and windows must also be installed. Pay special attention to the choice of tools that will help in the work.
How to make a house front: installation guide, price, photo
You will need the following kit: screwdrivers, drops, spatula, hammer, level, tape measure, electric drill press, reamer and wood, and some other tools, it all depends on the type of finish.
Leave ahead of time to think about where your home will be the outlet, all the water, and the switches.
Interior finishing work must be done on flat surfaces, so it is sometimes convenient to use gypsum boards to make any surface a right plane. This will make the end much easier. For the correct installation of such plasterboard structures, you will also purchase a special mounting profile.
A recorded drywall plate can be repaired with special adhesives, but this is a difficult process. Drywall will help you store finished materials.
When drywall sheets are installed, it is important to seal the seams between them tightly, which is done with ordinary putty. After that, you only need the wall colors in the color you want, or paste in the wallpaper.
There is another common way to finish walls - the use of PVC panels.
Thanks to these panels, you do not need to deal with additional procedures on the walls, you can forget the background and color. The joints of these plates are sealed with special plates that always come with the plates themselves.
Soil preparation is carried out using various screeds and mixtures that are self-levelling. When the mixture is drained, only the laminate remains on the floor, but of course you can use any other flooring.
Installation of laminate flooring does not take much time, and the material is reliable and worthy of the aesthetic appearance.
wall decoration
Wall alignment
wall decoration
Internal and external finishing is made with spacers and house interiors.
Wooden cladding is extremely popular in suburban housing construction. What will be discussed:
- about finishing technology;
- how to cover the walls and ceiling with the pedestal itself;
- from the cost of completing the work.
Working with wooden substrates as a finishing material is not such a difficult process, so any more or less qualified carpenter can solve it.
To be able to cover.
Wall rooms. When decorating the walls inside the room, the position of the panel can be vertical or horizontal, which greatly affects the visual effect of the room. Panels installed horizontally will visually make the room look longer and more vertical - shrink the space but make it "higher".
Ceilings. Underlayment is a widely used material for embedding ceilings in wood, not just houses.
The front of the building is often often trimmed with this material.
Wood lining - what building material is it?
Designed - Planned trip is about two inches thick (usually less than 1.2-1.5 cm) which is used mainly for interior interior walls and ceilings, and is often found in exterior trim houses (mostly) of houses. For the outside end, and the so-called "street" is often used, so it's only two inches thicker, and the outside fits perfectly.
Phases and technologies.
Before using the finishing panel, it must lie indoors for at least one day, the packaging must be removed.
This is done to equalize the humidity of the room and wood. After that, you can continue working. The first phase requires the preparation of the wall.
Some ideas about transforming the facade of a house
If the wall is smooth, the lining can be fixed directly on it, if it is not installed - install the so-called. Beacons, their roles will have wooden rods of the desired section, located at the level, but perpendicular to the chosen direction.
If necessary, the resulting precipitate is insulated and sealed by water vapor resistance.
The padding must then be cut into the boards that are needed and attached to the finished box. After completion of work, the panels can be covered with tonic compositions or varnishes.
As you can see, this is a simple process, it can be easily managed without the participation of experts.
In the same case, if you do not have the desire or ability to complete yourself, our services can be used.
It will be difficult for you to stop, but everything will be done efficiently and professionally.
If this page of our site was useful to you, share it with your friends and acquaintances:
Kitchen. wall decoration
Wall closure due to the specifics of this room should be scheduled for regular wet cleaning. The most common wall decoration in private houses and apartments is the white washing of the upper part of the walls with chalk while painting the lower part of the walls (oil paint) with oil paint.
The upper part of the walls can be painted with water-based paint. If you choose kitchen glue, it is recommended to use a damp and film-resistant background. But during this time, you get a regular background of very good quality, which can act as a wash - you can wipe them off with a towel without any damage. Recently, many have started using extruded polystyrene tiles to complete kitchen walls.
As with other materials used to fill the walls of a room, this method has both pros and cons. We will talk about them in the corresponding chapter. Good view of the kitchen and wooden walls.
And the walls, clad in wood, are completely washed away and seem to heat up in a room where the walls are covered with wooden strips. However, with this version of the kitchen part is somewhat reduced. And finally, tiles. There is no better finishing material than a kitchen worktop tile that contains all the kitchen utensils.
You can, of course, if you want, and the ability to cover all the walls of the kitchen. Usually the owners use combined options for finishing the kitchen walls, each of which chooses their own. Almost everything on the kitchen wall is tiled; if there is a corner version of the location of the kitchen equipment, 2 walls are tiled. The remaining walls - depending on the aesthetic needs and financial capabilities of the owner: chalk, paint, wallpaper, extruded tiles, wood.
The range, as you can see, is quite wide.