It is quite easy to clean the clogged toilet bowl, unless, of course, it is the toilet bowl that is clogged, and not the sewer pipes behind it. It's pretty easy to check. If the water does not leave only the toilet, then it is he who is clogged, then we read this article further. If the water does not leave even from the bathroom, from the sink, then the case is a pipe, there is a blockage of the sewer pipes after the toilet bowl, and possibly the sewer riser - serious intervention is required here.
As a rule, the toilet is stuffed with paper, berries in compote, chicken bones, small rags, bags, etc.
Citizens! The toilet is not a bottomless hole! You shouldn't send anything but kakule and paper there!
So, to clear the toilet blockage, we need an ordinary plastic one and a half or two liter bottle of lemonade or beer. Closed with a lid. The bottom of this bottle must be cut off.
Next, you need to fill the toilet with water. You can just flush the tank, but it is better to take hot (preferably very hot) water into a bucket and fill the toilet with it. Everything happens faster and better with hot water. Then we take our bottle with the bottom cut off, insert it into the hole in the toilet bowl and begin to make up and down movements with force, as if pushing the water further into the toilet bowl. Thus, by making a few movements, we will be able to remove a small blockage in our toilet. If this method does not help, then you have a serious blockage, here you need
If you have nothing at hand, not a plunger, an ordinary plastic bottle with a volume of 1.5-2 liters can come to the rescue. When choosing a bottle, make sure that the lower part of it passes freely into the drain hole and reaches the bottom.
We need a sharp knife as a tool. On the neck, you need to tightly screw the cap of the plastic bottle. Take a marker or felt-tip pen and draw a cutting line on the bottom and cut.
Try to cut the toilet flush bottle straight, without sharp waves or bends. Insert the bottle into the neck of the toilet bowl and make a forward motion with the cut part, pushing the water through, creating pressure.
After the problem is solved, rinse the toilet with hot water.
You do not need to pour boiling water, which can damage the faience coating of the toilet bowl, leading to microcracks due to a sharp temperature drop and even noticeable cracks in the walls. This also applies if the toilet is connected to the sewer through a plastic corrugation.
Working with a bottle resembles cleaning with a conventional plunger. A water hammer effect is created, destroying the blockage and pushing it into the sewer system.
Punching a bottle, the toilet, be prepared for a reverse water hammer that can spray a fountain on you and hit your clothes. It is best to change your clothes in advance and wear rubber gloves and goggles.
It is better to clean with a bottle before pouring hot water into it, this is especially important when the toilet bowl was previously drained of greasy slop from pots and pans, thus achieving softening of fatty deposits by first adding dishwashing detergent there.
A plastic bottle will help to cope with small blockages at home: toilet paper, cotton wool, a rag, pushing them down the drain.
Video: The toilet is clogged how to clean
How to unclog a toilet bowl at home without a cable
Plastic bottle rope
If you need to get some fallen object into the toilet, a homemade cable from a plastic bottle will help.
To make a homemade cable, take a five liter (5 liter) plastic bottle, but if you don't have one, you can use a 2 liter one, only the cable will be shorter. Use large scissors as a tool.
Take a marker (pencil does not draw on the plastic) and draw a spiral line 2-3 centimeters wide along the entire length of the bottle.
The lower part of the bottle (always the material is thicker and stronger) will be like a round handle - a ring. Cut the bottle all the way to form a plastic tape with a ring at the end. Make a hole in the end of the cable for the finger to enter freely. At an angle of 45 degrees, make notches along the spiral of the cable.
Do not make the notches deep so that the cable is strong.
Push the homemade cable, for the toilet, scrolling it along its axis into the neck, holding it by the handle. By rotating the cable, you can pick up debris and foreign objects and pull them out.
As you pull the cable out and clear the blockage in the toilet, you will notice how the water begins to flow, indicating that the blockage has been cleared. As soon as this happens, remove the plastic cable and rinse the toilet with hot water.
How to pierce a toilet with a doll
sandbag Using a doll (as the people call it a bag with sand tied to a rope) for punching the toilet bowl is possible, if the toilet is clogged, you can clean it yourself without a plunger and cable, eliminating small blockages from toilet paper, hair, etc.
Place the doll in the neck of the toilet and, holding it by the string, press the flush button. Then carefully remove the bag of sand, which, under the action of a water hammer and its own weight, pushes the congestion into the sewer pipe, clearing the drain.
Toilet rag without plunger
To do this, we need a large rag, a stick more than a meter long (a mop will do) and a few more small rags. With small rags, you need to plug all the drain holes in the apartment: a bathtub (you can use a cork), a sink, a sink in the kitchen, etc. Don't miss a single one.
A large rag should be wetted and squeezed out. Wrap it on a stick in such a way that it does not, under any circumstances, go into the pipe. It must be either secured with something, or held by the hand by the edge. The main thing is not to let her into the bowels of your white friend! In general, it should look something like the picture:
simple toilet cleaning rag Now we lower our "torch" as shown in the figure under number 2, lower the water and push the "torch" sharply ... there! But abruptly - it's not with all the foolishness to break the toilet. You need to make a short, neat and at the same time quick downward movement.
Pushed there. They lingered for a second. And just as sharply pulled out. Then push the "torch" sharply into the toilet again. So until the water comes off. After that, you need to drain the water again and do it all over again until the result is achieved. Keep in mind this moment, if you have an unclosed drain somewhere or there are loose connections of the fan pipe, then this cleaning method will not work. And at the same time it is not necessary to push the "torch" into the jolt with a flourish and at a run, because poop will be on the walls.
Toilet pump sticker
The Chinese and Korean industries have launched special films. It will help you quickly and effortlessly deal with small blockages in a matter of minutes. This film is very convenient for those who often rents an apartment and are ahead from place to place, there is no need to carry a plunger and a cable.
Add toilet paper to the blockage to increase water rise. Tape the tape around the perimeter of the toilet bowl on a dry surface, carefully smoothing it around the edges, releasing air. There should be no air bubbles and gaps. Drain the water and press the air bubble several times, pushing the air inward.
Video: Sticker-pump on the toilet from a blockage
A clogged drain in an apartment is an unpleasant problem, but when the toilet becomes clogged, it is doubly inconvenient, since the task requires an immediate solution. Salt deposits in the pipes often cause difficulty in draining the toilet. This is due to hard water, urea, or some other kind of sediment deposited on the walls of the pipes and narrowing their inner diameter.
Salt deposits in the pipe. The "aesthetics of the frame" is accompanied by a corresponding smell
Advice! To find out the localization of the blockage, open the taps in the bathroom and kitchen (water sources in the common drain). If here the water goes into the drain freely, then the reason is in the toilet. If its discharge is slowed down everywhere, then the problem is in the common pipe. In this case, call the plumbers - it will be difficult to cope with the trouble on your own.
Attention! If you find a blockage in the toilet, do not empty the cistern, as its minimum volume is 3 liters. For reliability, you can turn off the water supply tap so that it does not flow to the floor when the drain is clogged. Use a bucket, pouring no more than 1 liter of liquid into the toilet for testing.
Cleaning risers, especially in old houses, is a job for professionals
Important. Prevention of salt formations allows you not to spend further effort on cleaning the pipes. It is enough to fill all the plums in the apartment with a special cleaning liquid once every 3 months at night.
However, the main reason for blockages in toilets is the residents themselves, who use the plumbing fixture as a garbage chute. And if a meat bone accidentally got into the toilet is easy to remove, then a rag or paper blockage will require some effort.
Tips for clearing the blockage:
- When replacing sewer pipes, install new ones of the same diameter, no less.
- When making repairs in the toilet, close the toilet to prevent debris from getting into it.
- Don't be lazy to throw away trash (pads, newspapers, cat litter, etc.) in the designated areas. So you will save your time, and you will not blush in front of the plumber.
How to unclog a toilet bowl yourself
There are several ways to unclog toilet blockages. Their effectiveness depends on the complexity of the cork: material, volume, time of occurrence.
Advice! Before attempting to unclog the blockage, remove the water from the toilet to the level of the drain. A rag, sponge, or rubber bulb (enema) is suitable for this.
Mechanical methods to remove toilet blockage
Important. The diameter of the plunger tip must be larger than the diameter of the toilet bowl drain. This is the only way to create conditions for the occurrence of a water hammer.
This simple plumbing tool will help remove a small blockage in the toilet.
If the apartment does not have a plunger, then you can use plastic bottle, the bottom of which is cut off, and the lid is tightly twisted:
- the resulting device is gradually introduced into the opening of the toilet until the air in the bottle begins to push it back;
- with a sharp movement, the bottle is pushed all the way into the drain and immediately pulled out.
The generated pressure is powerful enough to break through the debris plug with two or three manipulations.
Plastic bottle + laws of hydraulics = homemade plunger
If the above methods did not help to fix the problem, then you can use household chemicals.
Clogging chemicals
Attention! If the connecting corrugation between the toilet bowl and the pipe is made of thin plastic, it can burst under the influence of boiling water. In this case, use warm water.
Attention! Before you decide to act drastically, pouring a solution of formic, hydrochloric or sulfuric acid into the toilet bowl, think about whether the agent will corrode the old pipes at the same time.
Professional plumbing cable
This is a special plumbing tool, which is a cable with a handle at one end and a nozzle at the other. There are many types of ropes (rope, spring, rigging, tension, etc.) with a diameter of 6 to 16 mm and a length of up to 60 meters.
For residential needs, a 5-meter Ø9 mm cable is enough. The nozzle at its end can be in the form of a weight (for punching) or a spiral (for removing a blockage)
1.
2.
3.
4.
Many property owners have to think about how to clean the toilet on their own. Even when expensive high-quality plumbing is installed, problems with cleaning sewer pipes can hardly be avoided.
The main thing is not to panic, because there are many practical ways to clean the toilet at home.
How to clean the toilet with a blockage
The simplest option, how you can quickly clean the toilet bowl and pipes, is to use ready-made products specifically designed for these purposes. They are liquids, gels, granules or powders, which are chemicals that have a composition that can dissolve contaminants.
In the event that, after using chemicals, the water still does not leave well, the cause of trouble may be a foreign object, and not organic clogging. A cloth or surface cleaning rag may have gotten into the plumbing fixture. In this case, clean the clogged toilet using physical methods.
It should not be forgotten that chemical agents are able to dissolve weak organic clogging, but if foreign objects enter the drain, they are powerless and are not able to eliminate the clog. But if you don't know how to remove plaque from the toilet, chemicals will help you in this matter.
Cleaning with a plunger
You can eliminate the blockage in the toilet with a plunger - this work has its own characteristics. This sanitary ware cleans the sewer system using a vacuum. For this, the tool is installed on the drain hole so that the water covers the rubber part of the tool. If there is more of it in the toilet than is required and you cannot do without a plunger, you will have to scoop up the excess liquid with a bucket.
With this position of the sanitary ware, it is necessary to make at least 10 intensive movements up and down, leaving the rubber seal on the drain. Then the plunger is removed with a sharp jerk and the procedure is repeated until the water level begins to fall. How it looks like removing a blockage with a plunger can be seen in the photo.
After successfully eliminating the blockage, cleaning the toilet continues with the use of a chemical agent and rinsing it with boiling water. Sometimes, instead of a plunger, they use a stick, on one end of which a rag is wound (read also: "").
Cleaning the toilet with a plastic bottle
So, when the toilet is clogged - how to clean it at home if there is no plunger. When there is no plunger at home, you can use the most ordinary plastic bottle with a capacity of 1.5-2 liters. Its bottom should be cut off, and the lid should be screwed on the neck. Then the bottle is inserted with its bottom into the hole and continuously moved up and down with effort several times. After eliminating the obstacle, the cleaning process is completed by flushing with hot water and usually the sanitary ware is fully restored.
Cleaning the toilet bowl with a plumbing cable
If all of the above options, how you can clean the toilet, do not help, you can use a plumbing cable, which is considered a professional tool (in more detail: ""). It is a metal rope with a sharp tip or spiral-shaped drill at one end and a handle at the other. The photo shows a plumbing cable designed for cleaning the sewer.The tool is slowly introduced into the drain hole with rotational movements in accordance with the movement of the clockwise. When an obstacle arises in his path, you should not stop, since he, most likely, rests against the toilet bowl.
The moment, if the drill gets stuck in a blockage, can be determined by the fact that movements are difficult both when moving clockwise and counterclockwise. In this case, they act in short up-down and left-right movements, thereby trying to push the obstacle into the sewer pipe. Working with the cable needs care so as not to damage the sewer system.
If the water level in the bowl of the device begins to drop, the cable is removed by rotating it in the opposite direction. When deciding how to clean the toilet, it must be remembered that plumbers work professionally with this tool. A solvent is poured into the drain hole after completion of the work. When water begins to go down the drain at the same rate, the toilet is flushed with a large volume of hot water.
The process of clearing a blockage with a plumbing cable requires certain practical skills, at the same time, inept movements can lead to new problems. If the sewer system is in poor condition due to prolonged operation, then they use other methods and decide how to clean the toilet, or call specialists.
How to clean the toilet with a bottle: a detailed description of the process
Any home should have sewer cleaning facilities. Clogs in toilets do not appear on schedule, but in those moments when no one expects problems and there is no time to go shopping.
In such cases, you can do with improvised means, and an ordinary plastic bottle will help save the situation. Let's take a look at how to flush the toilet with a bottle and what else you can use to quickly fix plumbing problems.
Causes of blockages in the toilet
A clogged toilet is one of the biggest troubles that can happen to a sewer. If the drainage of water stops, then sewage fills the bowl of the plumbing fixture, and a heavy smell spreads through the house.
If a blockage occurs, it should be eliminated as soon as possible, otherwise an unpleasant smell will appear not only in the apartment, but even in the entrance
Although the very first and most important thing is cleaning, it is still advisable to figure out what exactly triggered the stagnation of water in order to know how to properly handle the plumbing fixture in the future.
There are two main reasons why a blockage can appear: improper installation and negligence in using the toilet. The toilet bowl may malfunction if it is connected to the riser with a pipe that is too large. The slope is not enough for the normal drainage of wastewater, and deposits remain on the walls of the pipes.
The gap in the pipes gradually narrows, so sooner or later there comes a moment when it becomes insufficient for the passage of water. The cardinal way to solve problems associated with poor-quality installation of the device is correct installation.
When it comes to operation, it is important to remember that a toilet is a useful plumbing fixture, not a trash heap into which you can dump your garbage. The device is not intended for emptying cat litter boxes, throwing away cotton wool, rags, diapers, thread, food waste, construction waste and cement mortar residues.
Treating the toilet like a trash can inevitably end up clogging. You can't throw anything superfluous into it. Accidentally dropped objects should be immediately removed from the toilet, and not ignored and even less flushed, pushing further into the sewer pipe.
General principles of sewerage operation
The sewerage system consists of a riser and pipelines, which are designed to drain liquid waste from plumbing fixtures. The riser is a large diameter pipe and is usually located in the bathroom.
If in the toilet bowl of an apartment in a multi-storey building, water ceases to drain due to a blockage in the riser, this is a problem for all residents. Only public utilities can solve it. Special revision niches are provided for cleaning the risers
Modern risers are often made of plastic, but cast iron pipes are still installed in many homes. The advantage of cast iron is strength, and plastic risers are less prone to blockages. Most often old cast iron pipes are clogged. There are burrs on their inner walls, due to which deposits form quickly.
To prevent air from the sewage system from entering the room, a siphon is provided in the design of the toilet - a bend where a water plug (water seal) is constantly located. When draining, the water displaces and replaces this plug, pushing the sewage from the toilet bowl into the sewer riser.
When you press the button of the tank, the water is drained into the bowl, washing it, and passes further along the pipe into the riser. The blockage interferes with the proper functioning of the toilet and water remains in the bowl
If there is debris in the pipe and the water has not squeezed it into the riser, a blockage may form. Torn pieces of paper, waste, hair, threads are caught on sharp or large objects. Gradually, all this turns into a large lump of dirt, which narrows or completely blocks the section of the pipe.
Unclogging with a plastic bottle
If there are no sewage cleaning devices in the house, the situation can be saved with a regular 1.5-2 liter plastic bottle. Only a sharp knife is required from the tools.
The sequence of manufacturing a device for cleaning the toilet:
- Screw the cap tightly onto the neck of the bottle.
- With a felt-tip pen or marker, draw a line at the bottom of the bottle above the bottom.
- Use a sharp knife or large scissors to carefully cut off the bottom. Make sure that the cut line turns out to be even, without any special protrusions and depressions.
To clean the toilet, insert the bottle into the drain hole with the cut part and several times sharply, forcefully push the water up and down. Then rinse the toilet with hot water. Watch the temperature of the water: it should be hot, but not scalding. Otherwise, the plumbing may simply burst.
According to the principle of operation, a home-made cleaning device from a bottle resembles a plunger. Water is practically not compressed, its volume remains unchanged. By pushing the water into the toilet with a bottle, you can create a water hammer effect and thereby break up the blockage.
Choose a bottle of such a diameter that its bottom fits freely into the toilet drain. It is desirable that she reach the bottom
When cleaning the toilet with any tools, incl. and homemade, there is always a risk of damaging the plumbing or getting unpleasant "side effects":
- Too strong back and forth movements can ensure that the water does not rush into the pipe, as expected, but out. In this case, the toilet fountain can hit the ceiling.
- If you move it carelessly, you can hit the toilet or drop a hard, heavy object on top of it. This threatens the appearance of cracks and chips on the device, especially if it is made of fragile faience.
Such phenomena are uncommon, but they do happen, so caution should be exercised. The risk of a “reverse water hammer” exists if the toilet is clogged with solid objects: glass shards, debris, cement.
Thanks to the bottle, a pressure difference can be created, and the plug that closes the drain will move further along the pipe. Hot water will dissolve the fat deposits and push the dirt towards the riser
If scraps of paper, cotton wool, rags or other soft objects get into the toilet, then the plastic bottle is quite capable of pushing them into the sewer without any problems. You can also use it to get them out of the toilet. To do this, you will need to build a homemade plastic cable.
Plastic bottle rope
You will need a large 5 liter plastic bottle to make a plumbing cable. If there is only a 2-liter one, it will also work, but the product will be shorter. From the tools you will need large, strong scissors.
Work order:
- First you need to apply the markup. A regular pencil does not draw on plastic, so it is better to take a marker or children's felt-tip pen. Apply a 2 cm wide spiral strip along the entire length of the bottle.
- When making bottles, manufacturers use thicker plastic at the bottom of the products. The material bends worse, but it is much stronger than in the upper part. It is perfect for a handle that looks like a ring. Draw this detail right away.
- Cut the bottle along the lines. You should end up with a long spiral tape with a round element at the end.
- Cut a hole in the middle of the "ring" so that your finger can freely pass through it.
- Make notches along the entire length of the tape: cut it on both sides at an angle of 45 degrees. Make sure that the serifs are not too deep and the cable remains strong.
To remove or move objects stuck in the toilet, insert the homemade cable into the drain hole, holding the handle. Try to push the product as far as possible and gently scroll around its axis. When the cable reaches the blockage, the rotating motion will help pick up the debris on the notches.
To clean the toilet, it is better to choose a larger bottle and make a tape 2.5-3 cm wide, because more severe blockages form in these appliances than in sinks
Try to remove the jammed items. If that doesn't work, just push them into the pipe. A sign that everything worked out correctly will be a decrease in the amount of drains in the toilet. As soon as the impurities begin to go down the drain, rinse the device with hot water.
Cleaning the toilet with a doormat
In the absence of a plunger, even the most ordinary doormat can become a powerful weapon in the fight against toilet blockages. In addition to her, you will need a wooden block as thick as a mop handle. You can also use the mop itself, but this is not always convenient due to its long length.
The rag can be wrapped around the end of the squeegee and secured tightly with a string to prevent it from falling off when the handle is moved
The wet cloth should be folded up and used to plug the toilet drain hole. The result is a tight impromptu cork. In its center, you need to attach a mop or a bar and press hard several times, like a plunger handle. A sudden movement causes a water hammer and destroys the plug.
Unique Chinese method
The Chinese and Korean industry produces special toilet cleaning films. If you can find it on sale, be sure to buy and store it. In case of blockages, the film can be a real salvation, because eliminates them in a few moments.
The Chinese film is disposable. It is very convenient to store it. This is ideal for rented housing if tenants do not want to buy a cable or plunger, and then move it to a new place of residence.
The principle of cleaning a toilet bowl with a film is simple to the point of genius, but it looks rather strange, since you first have to increase (rather than reduce) the blockage. This is done by throwing crumpled toilet paper into the standing water of the bowl and draining the cistern so that the toilet is almost full to the brim.
The rim of the toilet bowl is wiped dry and a special high-strength film is glued. It should adhere snugly to the rim over the entire adhesive surface so that not the slightest gaps or air bubbles remain anywhere.
The places where the film fits to the toilet are carefully smoothed out. After that, water is drained from the tank several times to inflate the film, and the bubble is pushed down with smooth wave-like movements.
Two or three presses on the swollen film are enough for the mass of water and paper to break through the blockage and instantly merge into the sewer. After use, the film is carefully torn off the rim and discarded.
Some especially courageous "craftsmen" advise to use food instead of a special film. They offer to hermetically close the toilet with it, draw water and press from above in the same way.
This method raises great doubts, because the tightness of the cling film is questionable. In addition, it is not strong enough, so it may not withstand pressure and burst. In this case, the entire bathroom will be flooded with the contents of the toilet bowl, and the blockage will still not go anywhere. Better not to risk it.
Other ways to clear blockages
The modern market for plumbing fixtures is diverse: you can find any tools for mechanical cleaning of sewers. Some of them are very compact and easy to use. The classics of the genre are the rope and the plunger.
A metal wire rope may not always be usable because there is a risk of damage to the plastic elements of the sewer system. But a rubber or silicone plunger is an irreplaceable thing in the household.
An alternative to mechanical methods is household chemicals. Packing a good, specialized sewer cleaner is cheaper than any plumbing fixture and takes up very little space.
When buying household chemicals for cleaning the sewage system, carefully read the information on the packaging, which indicates for which pipes the products can be used.
Household chemicals not only corrode corks. It removes the plaque from the inner surfaces of the pipes, due to which the lumen narrows and blockages are formed. An additional plus is disinfection, which is never superfluous in the toilet.
Useful video on the topic
You can choose any of your favorite ways to clear the blockage in the toilet. We offer videos that will help you understand the operation of a plumbing fixture and fix problems.
A video through which you can understand how the toilet flush system works:
Detailed instructions for using a plastic bottle to clean the toilet:
The Chinese method of dealing with a blockage in the toilet using a special adhesive film:
There are many ways to clear toilet blockages, incl. very original. However, it is better not to reinvent the wheel, but to buy a regular plunger. If washed, dried after use and stored in a secluded corner of the bathroom, it will last for many years. If you did not take care of buying a plunger in time, and the toilet needs to be cleaned urgently, the bottle will help you.
sovet-ingenera.com
How to unclog a toilet bowl yourself at home
The toilet, paradoxically, is the most irreplaceable place in any apartment, so a clogged toilet can disturb the peace of the household. The article contains 9 of the most common methods in the fight against blockages: from budget to expensive, from light to cardinal.
Improvised means
First of all, you can try folk ways to remove blockages, which will not only help solve the problem, but also save the family budget.
Testing boiling water
A simple and free method of dealing with blockages, when an enamel or iron bucket of water is boiled and dramatically poured into the toilet.
However, the method is fraught with danger:
- Boiling water can scald household members. To break through the cork, it is required to turn the bucket sharply and vertically, which will lead to the formation of many splashes.
- Hot water can ruin the toilet itself. The temperature drop, at best, will lead to the appearance of small cracks on the surface, and at worst, the earthenware product may burst.
In addition, according to reviews who nevertheless ventured to test the method, boiling water helps only from light blockages with food waste or wood cat litter.
Soda with vinegar
Another budget-friendly toilet cleaning method is a mixture of baking soda and vinegar:
- Half a packet of soda is poured into the flush hole.
- 2 glasses of ordinary vinegar are poured there.
- Above the hole is laid with a large thick rag, for example, an old terry towel.
As a result of the chemical reaction of soda and vinegar, light blockages break through in toilets and bathrooms. A side effect of the method is the ability to ruin sewer pipes if you overdo it with baking soda. It is recommended not to try to increase the dosage.
Citric acid and laundry detergent
Lovers of soft multi-layered toilet paper often encounter blockages because of it.
An effective way to get rid of adversity, which at the same time will cleanse a faience friend of yellow stains or rust:
- 1 glass of any washing powder dissolves in warm water.
- 2 sachets of citric acid are poured into the solution.
- The mixture is poured into the toilet for 4-5 hours or overnight.
- In the morning, several buckets of warm water are poured into the toilet to rinse out the softened residues of the blockage and cleaning solution.
One of the most popular and effective remedies for stone deposits, old rust and other toilet contamination, which, among other things, will cope with a slight blockage.
The recipe for use is simple:
- First, the toilet is emptied of water. For example, the hand is wrapped with a rag, and then water is pushed out with piston-like movements.
- A bottle of "Whiteness" is poured into the drain hole. It is advisable to leave the product overnight.
In the morning, the pollution from the faience will go away for sure, and light blockages from paper or pet hair may disappear.
We use chemistry
In case of ineffectiveness of improvised folk methods, the next step is to apply industrial production means.
On store shelves, there is a large assortment of household chemicals for cleaning toilets and pipes, although they all consist of alkali or acid:
- Domestic brands. Inexpensive "Mole". "Blockage".
- Foreign brands. High price range media such as Tired, Domestos.
According to the instructions on the package, the required dosage of the product is poured into the toilet. After a few hours, all that remains is to wash off the remnants of the blockage. From the first try, household chemicals may not cope with the problem.
If the water begins to go away even a little, you should refill the product. If there is no effect at all, then you need to try more serious methods.
The main thing is to follow the safety rules:
- Do not mix chemicals of different types or manufacturers. It will be very lucky if the mixture that has changed its properties does not work, it will be worse if it spoils the plumbing or even the health of the household.
- Do not try to create a chemical mixture yourself or buy it from your hands, only use industrial designs. The result of chemical reactions can lead to anything, to say nothing of an unknown composition offered for a penny on street ruins.
- When using aggressive products, use protective goggles and rubber gloves.
Important: after cleaning the toilet with "chemistry", you should rinse it several times with water before using it for the first time.
Mechanical methods
Sand, debris or glass will not take any chemical agent, therefore in such cases experts advise to immediately use "heavy artillery": a plunger, a plastic bottle or a rope.
Ventuz
A dark rubber suction cup with a handle is familiar to many from Soviet life. With such a tool, you can try to push the blockage further into the sewer. In a common system, the pipe diameter is larger, so the debris will float away freely.
Plastic bottle
In some cases, a regular 1.5 liter plastic bottle with a stopper can be much more effective at clearing up the blockage than harsh chemicals or traditional methods.
Let's describe in detail the algorithm of actions:
- The bottom of the bottle is cut off, while the cork is not twisted.
- We put on long rubber gloves and lower our hand with the bottle into the hole of the toilet bowl, deep into the cut edge.
- Then, several times, with strong sharp movements, we drive the bottle further and further.
The method with a bottle is similar in effect to the actions with a plunger, but the power of the water hammer is many times greater. Due to the increased pressure, the blockage can fly out further into the riser and float into a wide drain.
Cable
The wire rope is considered a professional plumber's tool. It is profitable to buy such a tool than to pay several times more for calling a specialist with it.
A standard steel cable reaches a length of 7-10 meters, has a handle and a pointed tip.
In order to destroy stagnant garbage with it, you must:
- Holding the handle, immerse the tip of the tool to the maximum in the toilet bowl drain.
- Further, with rotational movements, it is necessary to advance the cable until it becomes clogged and try to push it through with gentle jerks.
Important: all movements must be carried out slowly and unhurriedly, since sharp and strong blows from the cable can damage the old sewer pipes.
Drastic measures
If it was not possible to remove the blockage using the available methods, it remains only to disassemble the toilet.
- In Soviet times, the toilet was fixed with cement, so a specialized tool is needed to dismantle it.
- The pipe leading to the toilet can also be embedded in the wall.
- If you disassemble it yourself, you can additionally clog the sewer pipe with construction waste.
If, nevertheless, a decision is made to remove the toilet with your own hands, then it is important to adhere to the following algorithm:
- Blocking the water supply to the tank.
- Dismantling the barrel and unscrewing the nuts fixing the base of the product.
- Next, you need to slightly move the toilet by opening the drain.
- Using a plumbing cable, carefully clean the elbow and part of the sewer pipe.
Cleaning the toilet is a rather unpleasant task that can take a lot of energy, nerves, time and money.
Tips from professional plumbers to help prevent blockages:
- Do not dispose of food waste, however small, into the toilet.
- You should not rinse off toilet paper and even more so other hygiene products. There were cases when even a baby diaper was pulled out of the riser.
- Clean the toilet monthly with baking soda or a commercially available product as a preventive measure.
Blitz Tips:
- If there is a blockage, first try to remember what could be the reason:
- Folk recipes with soda or citric acid will cope with food waste.
- Special chemicals will dissolve the laminated paper or the contents of the vacuum cleaner's container.
- Dense solid waste, such as clay, sand, can only be overcome by a cable.
- For such situations, at home it is better to have a mandatory set of baking soda, plunger, rope, as well as several pairs of long rubber gloves.
housetronic.ru
How to unclog a toilet bowl: looking for the most effective method
Digging in the toilet is not very pleasant, so the decision of the question of how to clear the blockage in the toilet is left on the shoulders of local plumbers. Despite the fact that they do an excellent job with this task, nevertheless, the masters breed such incredible dirt and stench in the house that one involuntarily thinks about the fact that next time you need to try to take the situation into your own hands and do everything yourself. But how? I don't understand anything about this matter, do I? Yes, there is nothing to understand here. There are only three ways to remove a blockage from the toilet - two "official" and one popular. We will talk about them in this article, in which, together with the site vannaja.net, we will learn what each of these methods is and which one is better.
What to do if the toilet is clogged
How to clear a blockage in the toilet: determine the location of the blockage
First of all, you need to remember that water from the toilet may not leave, not only because of a blockage in it. In most cases, all the troubles lie in the mud plug formed in the riser itself. Before you take any measures, you need to visit the neighbors in the riser - if this situation is not only with you, then this is definitely not a matter of your sewage system. In such a situation, you need to decide where this traffic jam is and unambiguously call the plumbers from the housing office.
Determining the place of the blockage is not so difficult - going down from the uppermost floor to the lower one, we are looking for an apartment in which everything is fine with this matter. As soon as one comes across, we can conclude that the blockage is between this and the upper floor. If the inhabitants of the first floor suffer from this misfortune, then the blockage is in the basement on the lounger. And this is also the diocese of plumbers from the housing office.
If only you have problems with draining water, then we can safely say that the blockage is in the toilet or on the lounger of your apartment wiring. Only now you can ask yourself a specific solution to the question, what to do if the toilet is clogged?
How to find a blockage and unclog a toilet
Clearing blockages with traditional tools: two ways
In most cases, the question of how to clean the toilet bowl is solved by plumbers using a cable or plunger. These technologies are quite simple, but they have their drawbacks.
In my opinion, the most correct solution to the question of what to do if the toilet is clogged is to use one proven folk method that helps to remove any blockages. We will talk about it further.
How to clear a toilet blockage with a plastic bottle
The solution to the question of how to clean the toilet, if it is clogged, probably lies quietly or stands with a supply of water somewhere next to the trash can. Yes, you heard right, we are talking about a 2 liter plastic bottle of beer or soda - it is she who is able to quickly and efficiently solve the issue of cleaning the toilet bowl. The principle of operation of such a home-made device is based on the laws of hydrodynamics. To be more precise, there is such a thing as a water hammer, which will have to be artificially created in the liquid stagnant in your toilet. How to do it? It's very simple - you just have to get a little dirty, so it's best to stock up on a pair of rubber gloves.
We take a two-liter plastic bottle and cut off its bottom with a sharp knife - we do not throw out the cap from the neck, but, on the contrary, we twist it tighter. Now we insert the bottle with the cut-off bottom into the toilet and slowly push it into the water until we feel the air resistance inside the bottle. Did you feel it? Now we sharply press the bottle into the toilet, which we have strength and immediately pull it out of there. The pressure resulting from such an action turns out to be very large - it pushes the blockage into the sewer.
As a rule, more than two or three such water hammers are not required to break through the blockage. Here you need to understand the principle of this method and not be afraid to apply it. In most cases, a person who is aware of this method of eliminating blockages succeeds the first time. So if the toilet is clogged and there is no water, you should not immediately run to the housing office - it is better to go to the nearest store for soda.
Before resorting to using one of all of the above methods, the excess water from the toilet must be bled out - it should remain as in a normal situation. Otherwise, you will not be able to use a plunger, a rope, or a plastic bottle.
The video shows another way to clean the toilet with your own hands.
Cleaning the toilet using household chemicals
Recently, the so-called household chemicals, which are a weak solution of acids, have become widespread. It is actively used to eliminate sewer blockages for the reason that it allows you to cope with most types of blockages without getting your hands dirty. It should be understood that it all depends on what your toilet is clogged with - if by some miracle socks found themselves there, then even strong acid is unlikely to help you, especially if other dirt has already adhered to the top of the rags.
How to clean the toilet bowl with household chemicals photo
If you have already decided to test the products of modern chemistry in practice, then it is better to use an acid in its pure form, for example, hydrochloric acid. It can be purchased in modern construction markets. You need to be extremely careful with it and use all kinds of protective equipment - you need to protect not only your hands and exposed skin, but also your eyes, and especially the respiratory tract. The water from the toilet should be drained to the maximum - only after that it will be possible to pour about a liter of hydrochloric acid into the toilet and immediately leave the room. The reaction will take place within 30-60 minutes. After this time, the acid will corrode everything there, and the toilet should be rinsed abundantly with water and cleaned with modern disinfectants. You need to be prepared for the fact that all connections in the sewer pipes, into which acid penetrates, will have to be additionally sealed. I believe that this method should be used only in extreme cases, when no other methods help.
That's all there is to say about how to unclog a toilet bowl. In my opinion, we need to act in more traditional, and most importantly, safe ways. I completely forgot to mention another old grandfather's method, which has been used since the times of the USSR. After scooping up the water, a pack or even two soda is poured into the toilet bowl. After its dissolution, an active alkaline environment is created, which quite easily copes with some types of blockages.
← Bath drain: types of siphons and their features, the principle of self-installation Which toilet to choose: varieties and their design features →
vannaja.net
How to unclog a toilet bowl?
In houses and apartments, problems with the sewer system periodically arise. It gets clogged. There are enough reasons for this phenomenon. But in order to eliminate possible consequences, you need to know how to quickly clear the blockage. There are recommendations and advice from the masters, without which it is impossible to cope with stagnation.
Signs
How do I clean the toilet? If you do not do the manipulations to eliminate the problem in time, a breakdown may occur. Everyone has the right to call a master, but he does not always arrive promptly, and it is quite possible to cope with his own hands. There are elementary tips to help you understand that a blockage has formed in the plumbing:
Any sign indicates that there is stagnation and it should be urgently removed.
Why is this happening?
It is believed that over time, any toilet can become clogged. And in order to avoid serious problems, it is worth paying attention to this periodically. How to clean the toilet at home? Actions will be effective only if you know why the traffic jam occurred. The reasons may be as follows:
- Violations during installation work. Not everyone may know how to create a drainage system, so at the installation level this must be remembered. If the angle of inclination is small, then flushing is poor. Waste begins to fix in some place, creating a tight plug.
- Unsuitable waste. Often, residents in the toilet wash away the remnants of food. This includes a lot - potatoes, cereals, peelings of fruits and vegetables, etc. As a result, stagnation forms, which accumulates in the system.
- Rubbish. This is not uncommon. They wash away a lot - glass, paper, bags, etc. The toilet is not a trash can, and you shouldn't do that.
- When there are animals in the house, the owners do not complicate their life and flush the used litter for the litter box down the toilet. And in the composition - a special clay capable of retaining moisture inside. When the lumps are in a humid space, they swell and stick together. The result is a tight plug.
These are common causes of blockages. But how do you clean the toilet at home? After finding out the reason, the cleaning process itself begins.
Cork elimination technique
There are plenty of ways to clean the toilet. The method is selected based on the problem. For an apartment or house, you can choose any option - mechanical or chemical. When the plug is too big, the chemistry will be powerless. Small congestions are removed without the use of mechanical action. After assessing the current situation, having studied the scale of the traffic jam and the reason that created it, they choose a method of work. Anyone can cope with this on their own, if you follow the basic rules.
Mechanical method
This option is common because it is the most effective. You don't have to call a plumber to do this. With a margin of time and tools, you will remove the blockage in a short time. You just need to have a device in the apartment. There are several of them:
These are two simple ways that do not require large investments and do not have the complexity of implementation. Even a person without experience will be able to clean a drainage structure. Sometimes it happens that even such methods do not help to achieve the desired effect. In this case, you will have to call the masters, although they can apply the same. What else will help clear up the blockage?
Chemical substances
Here's how you can still clean the toilet. There are many different products available on the market. After hitting the pipe, they fight the problem. They are available in different states - liquid and free-flowing. No need to worry - the drain system does not deteriorate even with prolonged contact. Below we will consider which tools are effective.
Vinegar and soda
These components are available in the kitchen of any apartment and house. They will be great help to solve the problem. If there are no such funds, then you can buy them in any store. You need to buy one pack of baking soda and a bottle of vinegar (70%). How to unclog a toilet bowl at home using these tools? It is necessary to remove the water if there is too much of it. After that, soda is poured in and pushed with a stick as deep as possible. Then 200 grams of vinegar essence is poured. To make the reaction go faster, hot water is used. According to people, this remedy helps in 20 minutes. But be careful not to burn your skin.
Pipe cleaning chemistry
The basis is chemical elements that can break down fat, salts and other constituents. There are both domestic and foreign manufacturers on the store shelves. But first, you must first read the instructions and understand for which pipes this or that product can be used. In addition to the blockage, an unpleasant odor is also removed. How does this method work? According to the instructions, the agent is selected and the required amount is poured into the pipe. Next is hot water in the right proportion. After such manipulations, you cannot use the toilet for at least one hour. When time has passed, the toilet is flushed with hot water or from a flush barrel.
The very process of fixing the problem will not be difficult. Everyone knows that it is easier to prevent a blockage than to clean it up. In a house or apartment, it is worth monitoring the drainage system, otherwise a serious emergency may occur one day.
Preventive actions
How to unclog a toilet block? In order not to look for an answer to this question, it is worth following the elementary rules for using the drainage system. This will not be difficult:
- The toilet should not become a trash can. After all, any waste - food or household - will sooner or later create a solid plug.
- Sometimes (once a week) it is worth using chemicals to avoid serious blockages.
- To avoid such problems, you need to periodically flush the system with a bucket of hot water.
- It happens that there is a fan riser in the room. Its work will be effective with constant serviceability. If the riser does not work, a blockage may form.
Elementary manipulations help to remove the blockage in the sewer pipe quickly, without involving a master. But there is no need to make mistakes - you should completely control the work.
fb.ru
How to clean the toilet at home
If you come to visit, then always in passing assess the cleanliness of the room, the design of the apartment. However, if the hallway and living room can leave a good impression, then after visiting the bathroom, your attitude can radically change.
Each person has ever faced a situation where it was urgently necessary to bring the plumbing into proper form for the arrival of guests or to remove a blockage in the pipe. Usually, for such small work, they do not call a plumber, but try to solve the problems on their own. So that after removing blockages and cleaning the toilet, you do not have to change the plumbing itself, pay attention to these recommendations.
Prevention and cleaning of the toilet bowl surface
Causes of blockages in sewer pipes:
- When installing the toilet, the installation rules were not followed. The master installed the wrong slope of the pipe, as a result of which it is difficult to drain;
- Ingress of a foreign body into the sewer pipes;
- Pipe wear and build-up due to long-term operation.
- Implementation of improper care of plumbing.
There are two ways out to solve problems arising with the work of the toilet:
- External cleaning of the toilet bowl surface for the purpose of disinfection and giving an aesthetic appearance;
- Removal of blockages in the drain pipe. This problem, mainly, becomes relevant when the water is poorly drained from the tank.
The market is overflowing with plumbing care products. However, they often contain hazardous acids and alkalis, which, in contact with the skin, can cause severe burns. And the vapors formed after use are harmful and have a strong specific odor. In addition, cleaning with these products should be done regularly. Folk remedies are not inferior in the quality of cleaning, moreover, they are absolutely safe for humans and are cheaper in price terms.
Plain vinegar is good for getting rid of urinary stones and rust. It will be more effective to use a 70 percent acetic acid solution. The vinegar should be warmed up in a saucepan and gently poured into the toilet. Then add baking soda and a little iodine. We leave the resulting mixture overnight or for several hours. Then we clean the surface with a non-metallic brush and rinse off.
Also, citric acid is an excellent folk remedy in the fight against plaque on the toilet. You need to empty a few bags of acid into the toilet and close the lid. After a few hours, as well as after using vinegar, wipe the surface and rinse with running water.
A more radical way to achieve aesthetic appearance is technical oxalic acid. You can get it at the pharmacy. Use very carefully, wearing gloves, as this substance is very toxic. Just dab a rag with water and sprinkle some powder on it. Then wipe the toilet with the resulting mixture. Then wait one hour and rinse with water.
Toilet cleaning methods
Cleaning with folk remedies
Use regular baking soda to clear a small blockage in your pipe. You need to take half a packet of baking soda and dissolve in warm water. After the resulting solution is poured into the toilet. Stir the water inside the knee with a brush. Wait a few hours or leave the solution overnight. Then drain the water from the tank. This procedure will help in removing a small blockage in the sewer pipe, however, to solve larger problems, attention should be paid to chemicals.
Chemical cleaning
The available drain pipe cleaners contain hazardous chemicals and should be used with extreme caution. Be sure to wear rubber gloves, try to protect the respiratory tract with a mask, as the fumes from the acids can harm the respiratory tract. Avoid contact with eyes and mucous membranes. Do not use two or more products at the same time, mixing of substances can give unpredictable results. To prevent the occurrence of large blockages, it is recommended to use these funds at least 2-3 times a month.
Cleaning with a plunger
The process of cleaning sewer blockages is carried out by creating pressure drops in the system, as a result of which the blockage is eliminated.
The scheme for cleaning with a plunger is as follows:
- Fill the toilet with water to such a level that it completely covers the plunger;
- Close the drain hole tightly with the plunger socket and press it down;
- Carry out several sharp movements up and down and remove the plunger from the hole;
- Repeat these steps several times until the blockage is cleared.
Cleaning the drain pipe with a rope
The cleaning cable is a hollow tube equipped with a handle, with a coiled wire at the end. The end of the cable is inserted into the knee of the toilet bowl until it stops, after which the handle rotates. To remove the blockage, you need to carry out these actions several times.
Removing the blockage with a "doll"
The device called a "doll" is a cloth bag filled with sand. To remove the blockage using this device, you need to firmly attach the "doll" to a strong cable or rope, place it in the knee of the toilet bowl and flush the water from the cistern. A "doll" guided by a stream of water will push through the blockage. Then remove the bag from the pipe and drain the water again.
After clearing the blockage using any of these methods, drain a few liters of hot water into the toilet. Perform preventive pipe cleaning on a quarterly basis to keep the sewer system in good condition.
We hope that the measures to eliminate blockages and clean the plumbing using the above proposed methods will help you to carry out repairs yourself at no extra cost.
Video
positroika-doma.ru
How to clean the toilet from the stone with your own hands
In good conscientious owners, the plumbing always shines with cleanliness. However, sometimes, after prolonged use and rare preventive cleaning, limescale and urinary stones begin to form under the rim and on the walls of the toilet. This problem is not the most pleasant, but solvable. Consider how to deal with pollution and what to do if you inherited a toilet bowl with a stone from the old homeowners.
We are looking for the reason for the appearance
To skillfully solve a problem, it is worth familiarizing yourself with its root causes. What is limescale? These are deposits of minerals in the water you use to flush down the toilet. These minerals are present in both river water and well water. Thus, the more often water is flushed out, the more the existing problem is exacerbated.
You can not only remove old plaque with your own hands, but also prevent its appearance. In especially advanced cases, plaque can clog the hole (or holes) from which water is supplied to clean the inside of the toilet bowl.
A urinary stone is a phenomenon that testifies to the laziness of the owners, who forget to flush the water behind them in the toilet after relieving themselves. Drops of urine dry out on the walls and lead to very ugly stains, and subsequently - the appearance of urinary stones. It is possible to clean them, but it is much better to prevent them by timely sanitary cleaning and cleaning of plumbing fixtures.
On a rough surface of plumbing, plaque forms much faster. Therefore, it sometimes makes sense to purchase new porcelain plumbing fixtures.
How to clean the toilet from stone using folk methods
If your toilet is so "overgrown" that the brush no longer rescues, and you and your guests are simply unpleasant to use the toilet because of disgust, you should arm yourself with the knowledge accumulated by many previous generations.
Folk methods can be applied in private houses with a local sewerage system (septic tank) and plastic pipelines.
Attention! As part of safety measures, the respiratory organs and skin of the hands should be protected from the ingress of cleaning agents and their vapors. Use rubber gloves and a respirator. Protect your eyes from accidental splashes.
Strong chemistry to combat mineral deposits
Attention! Before using this or that remedy, it is necessary to familiarize yourself with the factory instructions for use, where the amount of the drug for a single use and the duration of action are prescribed. It is necessary to protect the eyes, breathing and skin of the hands from accidental contact with acids and alkalis. Most of the products are not suitable for cleaning toilets in houses with plastic pipes and local treatment plants (septic tanks).
Liquid acids and alkalis
- Orthophosphoric acid (solution 5-7%). With this acid, you can clean not only the toilet from the stone, but also the internal parts of the cistern from the corrosion that has appeared. For use, pour about 100 g of acid solution into the tank and the toilet, after 10-15 minutes rinse with water and clean the surfaces with a brush (brush). The acid is not expensive, it does not affect enamel, rubber and plastic. Use with rubber gloves to protect hands.
- A solution of hydrochloric acid 33% is a very powerful toilet bowl cleaner, but requires extreme care when using it (protect your hands and do not inhale vapors). It is enough to wipe the walls and pour about one glass of acid into the toilet to quickly get rid of the dirt. Action time - 15 minutes. Close the toilet lid after application. Not suitable for use in toilets connected to plastic pipes.
- Liquid battery electrolyte. Usually used by car owners, but such a super powerful mixture of sulfuric acid and distilled water can rid your toilet of even strong limescale. The method of application and safety precautions are the same as for hydrochloric acid. Not suitable for frequent use.
- Chlorine. Many cleaning products are produced on the basis of chlorine, including the domestic "Whiteness" and the imported "Domestos". However, chlorine-containing preparations are extremely detrimental to health, therefore, despite their effectiveness, they are not recommended to be used. Method of application: apply to the surface, after 30-60 minutes, clean the toilet bowl with a brush and rinse everything off with water. Some "experts" pour "Whiteness" into the toilet bowl.
It is also effective, but quite dangerous (including for the health of the female reproductive system).
- Popular cleaning products. In stores, you can find a variety of liquid (creams, gels, solutions) products created specifically to combat chronic lime deposits and urinary stones. Such preparations are applied for 30-60 minutes under the rim of the toilet, after which the surface is cleaned with a brush. If necessary, the procedure is repeated several times. Products of popular brands: Cillit and Toilet Duck (preparations based on hydrochloric acid).
Abrasive powders
All commercially available abrasive cleaners are good at solving the problem of cleaning the toilet. However, tiny granules often leave micro scratches on the surface of the sanitary ware, as a result of which the limescale will reappear after a short period of time.
If there is no alternative to using abrasives, then they are used as follows: water is pumped out of the toilet bowl, after which a layer of powder is poured. Then you can leave the agent for action or immediately start cleaning with a brush / brush / hard washcloth. It is necessary to rub until the plaque completely disappears. The procedure is rather unpleasant and tedious.
Cistern tablets are not only a plaque remover, they are also excellent for the prevention of urinary stones. In addition, the means for the cistern have a pleasant aroma, disinfect and disinfect the surface of plumbing fixtures, and extend its service life. It is enough to purchase a package of the product you like and put 1 tablet inside the tank. As soon as the tablet begins to dissolve, the water will be colored in some shade. The disappearance of the coloring pigment in the water will indicate the need to add a new tablet to the tank.
In addition to preventive cleaning and emergency stone control in the toilet, it is recommended to adjust the water supply to the cistern. After all, excess water for flushing is not only financially disadvantageous, but is also one of the root causes of the appearance of lime deposits. The easiest way to reduce the volume of the tank is to put 1-2 plastic bottles of water in it. This will reduce consumption by 2-3 liters per use. And in the case of purchasing new plumbing, choose a tank with a double button and a mode of economical use of water.
Video - How to clean the toilet from the stone
kanalizaciyaseptik.ru
How to clean the toilet and remove the blockage yourself
The sewerage system may fail sooner or later! And it doesn't matter if we are talking about a private home ownership or an apartment in a high-rise building. Especially unpleasant emotions are caused by a situation when a blockage appears in the bathroom and the owner has to urgently resolve the issue and look for a way to clean the toilet. It is very important to understand that a blockage of this plumbing element can provoke clogging and other parts of the sewer pipeline in the house. But, as you know, there are no hopeless situations, and, despite the fact that the maintenance of the plumbing and sewerage system is a whole science, there are many methods of cleaning the toilet bowl.
Note! The most efficient and effective way to clear a toilet blockage is to call a plumber. Perhaps it is not cheap, but a professional will do all the work, and the question of how to remove a blockage in the toilet will not bother you at all.
First you need to try to find out the cause of the blockage. It is absolutely clear here that in the process of proper operation of the toilet, problems with it, in principle, cannot be. Therefore, most likely a blockage indicates the presence of a third-party bulk object in the toilet (usually rags, paper, bags). It is the extraction of them from the sewer system that will solve all the problems. This situation is especially typical for housing in apartment buildings, and residents of the lower floors are especially familiar with it.
Cleaning with a plunger
Almost everyone is “friendly” with this subject: they know it by sight and are familiar with its functional purpose. The plunger will quite effectively cope with loosening a slight blockage. Ideally, a plunger with a cone-shaped nozzle should be stored in the closet specifically for the toilet.
Cleaning the toilet with a plunger - a classic of the genre
Before you start bleeding the drain hole, the toilet is filled with water. Then the plunger is installed on the hole and several successive presses are made on its wooden handle. Then the device is abruptly retracted. It is these simple movements that contribute to loosening and clogging, and perhaps very soon the water will begin to flow unhindered where it should.
"Doll" and rope
If the use of a plunger did not bring the expected result, then it means that you will have to take measures to clean the hydraulic seal itself. And more specifically, the following will have to be done:
Option number 1. Make a "doll". That is, fill a rag bag with sand and tie a rope to it. Lower the "doll" into the toilet and press the flush lever. At the same time, lower the rope of the "doll" so that the stream of water carries it into the funnel of the toilet bowl. Such a "doll", heavy enough to break through the blockage in the water seal.
Option number 2. Use a special flexible cable, which is actually a rigid hollow shaft with a rotating handle. The end of the axle is equipped with a long, spiral-shaped arm of thick wire, connected to a cable with a flexible tube. It is thanks to this tube that the cable becomes more mobile and protects the inner surface of the plumbing element from mechanical damage. The spiral end of the cable is lowered all the way into the neck of the toilet bowl. The handle rotates clockwise and the cable is slowly pushed further into the water seal. Such actions should destroy the blockage. And to complete this method of cleaning the toilet, you need to flush the system with hot water.
Cleaning the toilet with a cable is very effective
Or maybe a plastic bottle?
Sometimes a non-standard situation can be solved with a simple plastic bottle. In it, you need to cut off the bottom and the homemade plunger is ready for use. When working with a bottle, all movements must be performed sharply. Just as in the case with a conventional plunger, the toilet is filled with water, the bottle is lowered with the cut end inward and pressed sharply on it. Then the bottle is also abruptly removed. Now you know how to clean the toilet with a bottle.
By the way: at first glance, such a primitive device is actually quite effective and is in the spare arsenal of almost every plumber.
Chemicals
Special household cleaning products are also very popular among consumers, aimed at high-quality elimination of blockages in the toilet:
- powders;
- liquids;
- granules;
- sprays.
In order to determine in a specific situation what kind of toilet blockage remedy will be most appropriate, it is necessary to understand the nature of the blockage. Therefore, when you find trouble, you should not panic, but you need to assess the situation and make the right balanced decision.
Attention! If a way out of the situation is not immediately found, then you should seek advice from the global network. By asking a query like: toilet blockage - what to do, you can quickly find expert advice.
Modern toilet cleaning tools are extremely effective
Folk recipe
Since the "Soviet" times, it has been popular as a means for removing blockages in the sewage system, including ordinary soda in the toilet. Half a pack of soda is poured into the toilet and dissolved in water. Thus, an active alkali is created, which in some situations can correct the situation. However, with difficult blockages with only one soda, the situation cannot be solved.
DIY ceramic heater