The door block is not a supporting element, so it should not be transmitted to the loads from building structures. Leave the gap of at least 5 mm between the box and construction of the building.
Mounting order
- Unpack the door frame.
- On a flat surface that excludes damage to the product, collect box items by selecting the desired side of the opening of the web. Check that the edges of the crossbar and the stroke are in the same plane, and at the place of their fit the clearance does not exceed 1 mm. On the back of the crossbar, captivate four through holes, then connect the elements of the box on the tapping screw. For self-pressing 4.2 x 70, we recommend the drill with a diameter of 3.5 mm.
- Insert the box in the doorway and secure the wedges (at least three points on each side).
- Using the level strictly vertically, the looped rack with a perforator and fastening screws will fasten it using gaskets between the opening and the box in the mounting places.
- Loosen the loop fastening screw and show the door leaf.
- Close the cloth, and install the rack from the lock so that the canvas lightened throughout the perimeter, providing a uniform gap, and secure the rack in this position.
- Open and close the cloth several times, making sure it is installed correctly and nothing interferes when closing. The correctly installed door (when opening it at 45 °) should not spontaneously open or close.
- Finally secure the loop on the screw and install the accessories.
- Fill the mounted gap between the box and the wall of a small-arms of the mounting foam (when using the foam, be guided by the manufacturer's instructions).
- The platband is recommended only after complete drying of the mounting foam. For the period of drying the foam (about 12 hours), the door should be kept in a closed state.
Changing the support of the web
The deaf canvas standard in size height is both right and left. This is achieved due to the symmetry of the vertical cloth.
To change the direction of opening the door, it is necessary:
- unscrew the fastening screws and pull the lock case from the door, turn it 180 ° (so that the lock tongue is on top, over the bolt), set the lock in this position back;
- pull the rigle with the help of the passage from the lock case by 3 mm and turn it 180 °.
Required tools Tools: A screwdriver with a set of bit, a perforator or a shock drill, a level, wood-hacksaw, a roulette measuring.
Before installing the outer doors, carefully examine the installation instructions. Jeld-Wen is not responsible for product defects obtained as a result of improper storage, operation or installation.
Storage
Check the goods immediately after receiving! Improper product or defect product is not suitable for installation!
Doors should be stored in a well-ventilated room inside the building on a horizontal and smooth surface. Avoid the appearance of scratches and other mechanical damage!
You can not store doors in the place where the straight sunlight penetrates, in an unimagnant and wet room, on earth or concrete, and should be laid on a solid, smooth and dry surface.
Installation of outer door
The door must be installed in such a way that it is not directly affected by heavy rains and solar radiation. The door must be installed in a niche located in the wall or placed above the door canopy.
- Doors of dark tones under the influence of intensive solar radiation can be twisted and sweep.
- It is not allowed to change the size of the product, applying cuts and repainting. If necessary, consult with the representative of the plant.
- When installing and repairing the door, the door must be protected by a building cardboard or film to avoid her damage during finishing.
- Protect the door (pen or paper) during finishing work at the facility until their complete completion! When using adhesive tape to fasten the film or paper, make sure that the tape adhesive side is not glued to the door or box.
Required tools: waterproofing, hammer, saw, screwdriver, levels (500 mm and 2000 mm), corner, drill, mounting wedges, pencil, roulette, hex key, insulating wool and sealant.
The entrance doors are supplied in the kit - the box is mounted with the threshold and the door is suspended on the loop.
Before starting the installation, make sure the product and its configuration:
- Door leaf
- Door box
- Loops, lock case, locking plank
- Threshold
- Sealers, plugs for mounting holes
- Installation instructions. Warranty conditions.
Installing outdoor doors FUNCTION and CLASSIC and doors for balconies
|
Put the door kit on the opening side down! Open the packaging from the edge (from the outside plane of the box to avoid the possible appearance of scratches on the external trim)! Separate the box from the canvas! Separate the box from the canvas! |
|
|
Check also to the vertical and horizontal boxes were straight! |
 |
 |
|
 |
|
 |
|
 |
|
 |
|
 |
|
 |
|
|
The entrance doors can be adjusted in height and horizontally. Adjustmentbyheight - adjustmentdoorsup
Height adjustment - door adjustment down
Horizontal adjustment - reducing the distance between the door and the door frame from the loop
|
 |
| Install the plugs on the mounting holes. Install the lock and handle. |  |
| To fill the gap between the box and the discovery, use insulation materials (glass gamble, mineral wool or mounting foam). The gap between the threshold and the floor can be filled with silicone. |  |
|
Install the entrance door to a niche or under the canopy. The minimum canopy should be 70 mm wide, but when you install the inlet door having glazing, we advise you to use the at least 500 mm width. |
 |
 |
Installing the Basic Entrance Door
Before installing the door, check whether it matches the size of the doorway and how smooth and has straight corners. The doorway should be more external box sizes at 15 - 45 mm. If necessary, adjust it. Check also that the base under the threshold is horizontal and rigid.
|
Put the door kit on the opening side down! Open the packaging from the edge (from the outside plane of the box to avoid the possible appearance of scratches on the external trim)! Separate the box from the canvas! |
 |
|
Check that the base under the threshold is horizontal and stable! Attach the threshold to the floor using Silicone! Check also to the vertical and horizontal boxes were straight! |
 |
| To secure the door frame, choose a special fixture accessory! You can use screws together with wedges or sleeves. With the use of the sleeves, the wedges do not need. |  |
|
First fasten the loop side of the box and then lock! The gaps between the box and the doorway can be as 20 mm as possible. Check if the straight box! |
 |
| Fastener accessories Choose in accordance with the material of the wall! |  |
| If you use the sleeve, the mounting wedges will not be needed, as the sleeve allows you to adjust the remoteness of the box from the doorway. |  |
| Check that both the vertical and horizontal boxes were straight! |  |
| Hang the door on the loop! To do this, loosen a bolt slightly, hang the door and tighten the bolt. Then screw the loop, using screws! Make sure the corner of the door does not hit the floor! When hitting the finish may be damaged! |  |
| Close the door and look to the door canvas (especially the corners on the lock side of the box) was on the same level with the box! |  |
|
If necessary, adjust the plane of the doors with the hinge! Adjustment in height
Side adjustment
|
 |
| Close the mounting holes by plastic plugs! |  |
| Fill out the space between the threshold and the floor of Silicone! If necessary, lay the bars! |  |
| Install the entrance door to a niche or under the canopy. The minimum canopy should be 70 mm wide, but when you install the inlet door having glazing, we advise you to use the at least 500 mm width. |  |
|
Using the insulating wool strips, fill the gap between the box and the wall opening so that the wool strip leaves the free space to the outer edge of the box of 10-20 mm. From the inside of the box, use for gluing insulating wool to the glue box! With the outside of the box, do not use the box! Install platbands! |
 |
| Adjust the screws that keep the locking bar so that the door closes tightly! |  |
Outdoor door care instructions
- If the door is not damaged and is not very worn, it is sufficiently light cleaning with the help of conventional detergents (not alkaline). In order for the door to save the glitter, it can be possible once a year after cleaning to process it with wax for cars. It also facilitates the subsequent cleaning. Purification by abrasive substances and solvents is prohibited.
- Veneered exterior doors clean the dry and clean cloth. It is desirable once a year to rebuild the door cloth and the box. For this purpose, use painted oils intended for use in external conditions (when painting, examine the instructions applied to the goods).
Follow the instructions, be accurate with sizes and test results. Carefully examine the instructions before starting to install. The outer door is designed primarily for use as an entrance door in private houses for year-round living, mansions and townhouses, in buildings where thermal insulation qualities are required.
It is strictly forbidden to mount the doors in the house under construction or indoors, where wet works are underway (for example, floor concreting, screed pouring, etc.). Excessive humidity can lead to wood deformation and paint peeling. In addition, accessories, including the castle hull, can be covered with rust.
ATTENTION! When installing the entrance doors during the cold season, it is necessary to use certified mounting foams specifically designed for use at low temperatures - information with specific recommendations for use is usually applied by the manufacturer on the cylinder.
Always install moisture insulation (bitumen strip, etc.) between the horizontal base and the threshold.
Never install the box directly on the concrete floor or screed! Use, for example, a bitumen strip, etc.
Doors should be installed in places with a sufficiently long sink of the roof or a canopy above the door, which will protect the surface of the door from moisture and sun rays.
When determining the sizes of the canopy should be guided by the following formula: the width of the canopy D should be at least half of the height of the canopy (distance from the bottom of the door to the bottom of the canopy, see the scheme).
Stages of installing the entrance door:
Stage 1.
Check that the base under the threshold is horizontal.
Install the reference to the mounting point and place the collected box on it.
Mix the seam sealing mass.
Single can be installed later. In this case, make a tide under the threshold
and stick it by installing the groove intended for it in the verge.
Stage 2.
Secure the box in the installation of the wedges with wedges, inserting them above the mounting holes of the box so that the side of the box with the loops was exactly vertical (both in parallel and in the predetermined direction to the wall plane). Use two wedges on each mounting hole in the box, one wedge Insert the outside, the other - from the inside. Check with Waterpas, that the box is exhibited smoothly.
Make sure the perimeter of the box is enough space for the seal
and fasten the side of the box with the loops of fastening screws to the wall.
Stage 3.
Install the anti-burglar pins in the door. Do not twist them to the end, leave the stock of 10mm. Take the door leaf on the loop.
Tighten the anti-burglar pins before the failure, install and tighten the loop fastening screws.
Stage 4.
Make sure the threshold is set horizontally. Place smoothly side of the box with a locking lock (in both parallel and in the predetermined direction to the wall plane). Secure the box to the wall of fastening screws.
Stage 5.
Use the hex key to adjust the door height. Before adjusting the door to the side, loosen the anti-burglar pins and fastening screws. Adjusting to the side, designed for this, adjusting screw. After adjustment, tighten the anti-broken pins and fastening screws.
Adjusting the jeld-wen entrance doors
The position of the outer door web can be adjusted in height and horizontally using the loop adjustment.
This is especially true, for example, when shrinking at home.
Adjustment in height
Required tool: Hex key 5 mm.
Door adjustment up
- Loosen the upper adjusting screw (1) on all loops by turning it with a hexagon for 2-3 turns.
- Turning the adjusting screws (2) on the bottom of the loops - set the door to the desired position in height.
- Be sure to tighten the screws of all loops to an equal number of revolutions to evenly distribute the weight of the door on the hinges.
- Tighten the locking screws on top of all loops (1).
Adjusting door down
- Loosen the lower adjustment screw (2) on all loops besides one by 2-3 turns.
- Turning the screw (2) of the remaining loop counterclockwise, lower the door to the desired height.
- Tighten the adjusting screws (2) the rest of the loops to the same position to evenly distribute the weight of the CVRI in all loops.
- Finally, tighten the upper adjustment screws (1) without excessive effort.
Horizontal door adjustment
Tools Next: Hexagon 5 mm, Cross screwdriver.
Increasing the distance between the door and the door frame from the loop
- Tighten the adjusting screws (4) on one of the loops in such a way that the door leaf opens in the desired position. .
- Tighten the adjusting screws (4) on the second loop (on the rest of the hinges) to align the door canvate and evenly distribute the weight of the door.
Reducing the distance between the door and the door frame from the loop
- Loosen on all hinges fastening screws (3) and anti-blank pin (5) by 2-3 turns.
- Loosen on one of the loops adjusting screws (4) in such a way that the door canvas occupied in the desired position. .
- Loosen the adjusting screws (4) on the second loop (on the remaining hinges) to align the doorbell and evenly distribute the weight of the door.
- Gently tighten the screws (3) and anti-blank pins (5).
Stage 6.
Is the door close tight?
The closing density can be adjusted by adjustments in the response bar.
Stage 7.
Carefully compact the gap between the wall and the box by filling it with mineral wool. Loose, then, the gap sealing elastic mass for the seam pairproof production. Do not use polyurethane foam, because when expanding it can deform the door frame and complicate the possible subsequent regilies of the door.
Outdoor door maintenance instructions
Painted products
Products are painted with moisture-resistant paints that meet the requirements of scratch-presented to the occurrence of scratches, to wear resistance and appearance of the surface and that are well withstanding the impact of many household chemicals, fat and solvents.
Cleaning
Use conventional detergents (unintelling), for example, dishwashing fluid. For mold cleaning, use special means to remove mold. Do not use detergents that can scratch or dissolve the painted surface. Avoid, for example, the use of solvents, abrasive powders, metallic fiber sponge, etc. Moisten the surface from the bottom up, but wash it from top to bottom. Otherwise, the lanes may appear on the doors. Watch dry.
Service
It usually happens quite normal washing, if the door is not damaged or not worn out. To preserve the shine, it is recommended, however, after washing, grate the surface of the door, for example, by car wax.
Tinting
Small damage is best tinted with a brush and suitable alkyd or acrylate enamel, designed for external work. Check first the compatibility of paint with the material of the original coloring on a small surface, for example, painting a small area on the edge of the door from the loop.
Product quality and warranty conditions on Jed-Wen doors
Jeld Wen manufactures its products in accordance with the requirements of a unified European standard SE.
What is CE?
The CE sign is a guarantee for the consumer that this product complies with the basic requirements of the European Unified Standard and therefore may be legally posted on the market.
CE marking has long been required on such products as toys and electronics, but, recently, this unified standard is installed for certain building materials.
What does this mean for the consumer?
All products with CE marking are product data in the format provided for in the Declaration of Quality Characteristics "Declaration of Performance" (DOP), which allows you to clearly and easily compare between similar products and provides a consumer with the necessary information to make a reasonable solution.
DOP provides key information on the performance characteristics of the construction disfiguration, which was tested by independent experts and was certified by the EU body.
All products that fall under these directives are subject to marking the SE sign either on the product itself or on its packaging - the CE logo and the number that indicates the corresponding DOP.
Product discrepancy with the requirements of the CE standard in terms of the curvature of the web or the box is considered a warranty defect.
We apologize if you encountered Jeld Wen Product Defect! When a defect is detected, please contact us and inform the order number. Together the attention is that the defective product is not subject to installation and operation!
How to measure whether the door canvas twist?
Put the door leaf on a flat horizontal surface
Measure the distance between the central part of the door leaf and the surface on which it is located (mm)
Permitted curvature up to 5 mm per door canvas
How to measure, is the door box be curved?
Wall curvature
Put the box (plafhone) on a horizontal smooth surface so that the ends of the box touches the Earth.
The permitted curvature of the box in the direction of the wall is 3 mm / per meter (that is, the box with a height of 20m and 21m 6 mm per vertical box.
Curvature of the edge of the box
Put the box on the side on the smooth horizontal surface so that the ends of the box touches the surface.
Measure the gap between the central part of the box and the surface (mm).
Permitted curvature of the box in the direction of the edge of 1.5 mm / per 1 meter (i.e., a box with a height of 20m and 21 m to 3 mm for one vertical)
We are not responsible for the defects of the product resulting from its natural wear, improper storage, installation and operation.
Follow the instructions, be accurate with sizes and test results. Carefully examine the instructions before starting to install. The outer door is designed primarily for use as an entrance door in private houses for year-round living, mansions and townhouses, in buildings where thermal insulation qualities are required.
It is strictly forbidden to mount the doors in the house under construction or indoors, where wet works are underway (for example, floor concreting, screed pouring, etc.). Excessive humidity can lead to wood deformation and paint peeling. In addition, accessories, including the castle hull, can be covered with rust.
ATTENTION! When installing the entrance doors during the cold season, it is necessary to use certified mounting foams specifically designed for use at low temperatures - information with specific recommendations for use is usually applied by the manufacturer on the cylinder.
Always install moisture insulation (bitumen strip, etc.) between the horizontal base and the threshold.
Never install the box directly on the concrete floor or screed! Use, for example, a bitumen strip, etc.
Doors should be installed in places with a sufficiently long sink of the roof or a canopy above the door, which will protect the surface of the door from moisture and sun rays.
When determining the sizes of the canopy should be guided by the following formula: the width of the canopy D should be at least half of the height of the canopy (distance from the bottom of the door to the bottom of the canopy, see the scheme).
Stages of installing the entrance door:
Stage 1.
Check that the base under the threshold is horizontal.
Install the reference to the mounting point and place the collected box on it.
Mix the seam sealing mass.
Single can be installed later. In this case, make a tide under the threshold
and stick it by installing the groove intended for it in the verge.
Stage 2.
Secure the box in the installation of the wedges with wedges, inserting them above the mounting holes of the box so that the side of the box with the loops was exactly vertical (both in parallel and in the predetermined direction to the wall plane). Use two wedges on each mounting hole in the box, one wedge Insert the outside, the other - from the inside. Check with Waterpas, that the box is exhibited smoothly.
Make sure the perimeter of the box is enough space for the seal
and fasten the side of the box with the loops of fastening screws to the wall.
Stage 3.
Install the anti-burglar pins in the door. Do not twist them to the end, leave the stock of 10mm. Take the door leaf on the loop.
Tighten the anti-burglar pins before the failure, install and tighten the loop fastening screws.
Stage 4.
Make sure the threshold is set horizontally. Place smoothly side of the box with a locking lock (in both parallel and in the predetermined direction to the wall plane). Secure the box to the wall of fastening screws.
Stage 5.
Use the hex key to adjust the door height. Before adjusting the door to the side, loosen the anti-burglar pins and fastening screws. Adjusting to the side, designed for this, adjusting screw. After adjustment, tighten the anti-broken pins and fastening screws.
Adjusting the jeld-wen entrance doors
The position of the outer door web can be adjusted in height and horizontally using the loop adjustment.
This is especially true, for example, when shrinking at home.
Adjustment in height
Required tool: Hex key 5 mm.
Door adjustment up
- Loosen the upper adjusting screw (1) on all loops by turning it with a hexagon for 2-3 turns.
- Turning the adjusting screws (2) on the bottom of the loops - set the door to the desired position in height.
- Be sure to tighten the screws of all loops to an equal number of revolutions to evenly distribute the weight of the door on the hinges.
- Tighten the locking screws on top of all loops (1).
Adjusting door down
- Loosen the lower adjustment screw (2) on all loops besides one by 2-3 turns.
- Turning the screw (2) of the remaining loop counterclockwise, lower the door to the desired height.
- Tighten the adjusting screws (2) the rest of the loops to the same position to evenly distribute the weight of the CVRI in all loops.
- Finally, tighten the upper adjustment screws (1) without excessive effort.
Horizontal door adjustment
Tools Next: Hexagon 5 mm, Cross screwdriver.
Increasing the distance between the door and the door frame from the loop
- Tighten the adjusting screws (4) on one of the loops in such a way that the door leaf opens in the desired position. .
- Tighten the adjusting screws (4) on the second loop (on the rest of the hinges) to align the door canvate and evenly distribute the weight of the door.
Reducing the distance between the door and the door frame from the loop
- Loosen on all hinges fastening screws (3) and anti-blank pin (5) by 2-3 turns.
- Loosen on one of the loops adjusting screws (4) in such a way that the door canvas occupied in the desired position. .
- Loosen the adjusting screws (4) on the second loop (on the remaining hinges) to align the doorbell and evenly distribute the weight of the door.
- Gently tighten the screws (3) and anti-blank pins (5).
Stage 6.
Is the door close tight?
The closing density can be adjusted by adjustments in the response bar.
Stage 7.
Carefully compact the gap between the wall and the box by filling it with mineral wool. Loose, then, the gap sealing elastic mass for the seam pairproof production. Do not use polyurethane foam, because when expanding it can deform the door frame and complicate the possible subsequent regilies of the door.
Outdoor door maintenance instructions
Painted products
Products are painted with moisture-resistant paints that meet the requirements of scratch-presented to the occurrence of scratches, to wear resistance and appearance of the surface and that are well withstanding the impact of many household chemicals, fat and solvents.
Cleaning
Use conventional detergents (unintelling), for example, dishwashing fluid. For mold cleaning, use special means to remove mold. Do not use detergents that can scratch or dissolve the painted surface. Avoid, for example, the use of solvents, abrasive powders, metallic fiber sponge, etc. Moisten the surface from the bottom up, but wash it from top to bottom. Otherwise, the lanes may appear on the doors. Watch dry.
Service
It usually happens quite normal washing, if the door is not damaged or not worn out. To preserve the shine, it is recommended, however, after washing, grate the surface of the door, for example, by car wax.
Tinting
Small damage is best tinted with a brush and suitable alkyd or acrylate enamel, designed for external work. Check first the compatibility of paint with the material of the original coloring on a small surface, for example, painting a small area on the edge of the door from the loop.
Product quality and warranty conditions on Jed-Wen doors
Jeld Wen manufactures its products in accordance with the requirements of a unified European standard SE.
What is CE?
The CE sign is a guarantee for the consumer that this product complies with the basic requirements of the European Unified Standard and therefore may be legally posted on the market.
CE marking has long been required on such products as toys and electronics, but, recently, this unified standard is installed for certain building materials.
What does this mean for the consumer?
All products with CE marking are product data in the format provided for in the Declaration of Quality Characteristics "Declaration of Performance" (DOP), which allows you to clearly and easily compare between similar products and provides a consumer with the necessary information to make a reasonable solution.
DOP provides key information on the performance characteristics of the construction disfiguration, which was tested by independent experts and was certified by the EU body.
All products that fall under these directives are subject to marking the SE sign either on the product itself or on its packaging - the CE logo and the number that indicates the corresponding DOP.
Product discrepancy with the requirements of the CE standard in terms of the curvature of the web or the box is considered a warranty defect.
We apologize if you encountered Jeld Wen Product Defect! When a defect is detected, please contact us and inform the order number. Together the attention is that the defective product is not subject to installation and operation!
How to measure whether the door canvas twist?
Put the door leaf on a flat horizontal surface
Measure the distance between the central part of the door leaf and the surface on which it is located (mm)
Permitted curvature up to 5 mm per door canvas
How to measure, is the door box be curved?
Wall curvature
Put the box (plafhone) on a horizontal smooth surface so that the ends of the box touches the Earth.
The permitted curvature of the box in the direction of the wall is 3 mm / per meter (that is, the box with a height of 20m and 21m 6 mm per vertical box.
Curvature of the edge of the box
Put the box on the side on the smooth horizontal surface so that the ends of the box touches the surface.
Measure the gap between the central part of the box and the surface (mm).
Permitted curvature of the box in the direction of the edge of 1.5 mm / per 1 meter (i.e., a box with a height of 20m and 21 m to 3 mm for one vertical)
We are not responsible for the defects of the product resulting from its natural wear, improper storage, installation and operation.
Finnish doors began their victorious procession on the expanses of the post-Soviet space countries at the end of the last century. People began to trust the fact that high quality can stand at a low price. White fillety doors of Finnish manufacturers who still not only hold, but also expand the niche of their goods, familiar to everyone. Most people wish to have durable, reliable, comfortable and durable doors.
Finnish doors began their victorious procession in our country more than 10 years ago. The use of environmentally friendly materials and the most modern technologies allows producing good and high-quality products, designed for a long service life without losing their consumer qualities.
The range and color gamut currently supplied Finnish doors is so wide that they can satisfy the most sophisticated taste of the buyer. These are interroom doors, doors for saunas, bathroom doors, fire-fighting, entrance and others.
Despite this diversity, interior doors are still the largest and most sustainable demand. Previously, the overwhelming part of the Finnish interior doors supplied to our country was smooth frame with cellular filling or pulley doors from the pine massif. Typically, such doors were white or gray. Now they were added fanwood and melamine doors. Fanroom doors are fronted with veneer of valuable wood - oak, beech, grab, mahagon. Melamine doors are coated with melamine, imitating veneer of some types of wood - walnut, cherries, pears, etc.
All varieties of Finnish doors have one distinctive design feature, which is advantageous from the main mass of other doors. This is the presence of a preliminary strip or special protrusion on the doorway, which close the gap between the web and the door frame. This design allows you to improve heat and sound insulation of the Finnish doors. In addition, the ledge of the door canvase makes imperceptible possible when installing flaws.
The interroom kit includes a door frame with embedded loops and a door leaf with a fixed lock, which allows you to minimize damage arising during the installation of doors.
Finnish interior doors adapted to Russian conditions. Thanks to the thickness of the door frame in 92 mm, they are suitable for installation in any intra-ordinary partitions. The height of the door box of the Finnish doors is 210 mm, which exceeds the Russian standard for several centimeters. Therefore, sometimes there is a need to cut a little door.
Before acquiring Finnish interior doors, determine which doors you need - left or right. If the door hinges are located on the left of you - this is the left door. Left locks are installed in such doors. And if the door loops on the right is the right doors with the right lock. You must be located in the room where the door opens.
Installation Finnish doors.
The door block consists of a strapping box and one-or two-door cavot. By design and functional purpose, the doors are divided into shield and frame, exterior, internal, balcony, etc., with and without a threshold, with fraumuga and without fraamuga, glazed and deaf ...
Shield doors consist of a frame, filling and oven.Frame executedfrom Bruska (RESEK), Casing - from gluedplywood, veneer, solid wood fiber plates, filling from small lumber, plywood waste and solid fibreboard, paper cells. Foams and others. On the perimeter of the door canvas is framed by wooden plates.
The doors of the framework (fillety, strapping) consist of inside (bars) and aggregate (fillets). As a panel, you can use glass, boards, phaneur, fiber and chipboard.
In the drawing, the doors are divided into one-board, double-fledged with cloths of the same and different widths, and according to the opening method - on the right-hander with the opening of the door leaf counterclockwise and the left opening with the opening of the door canvase.
Parade and interior doors can be deaf or glazed. Often the door blocks have the upper part (fraamuga) glazed and fasten the glass in a box or on the door instead of the panels insert the glass.
The door can be constructed independently, order a wizard or purchase in the store. More durable doors from oak or beech, more beautiful - made of mahogany or ash.
Installation of door boxes and doors. When installing the door frame of the input door, the block is lifted and installed in the opening on the lining from the roofing on the mastic. Recently, the door frame is most often installed on the mounting foam. It is necessary to ensure that the lower bar occupy a strictly horizontal position. Vertical and horizontal elements are installed on the coal, plumbing and level. The plumb should accurately pass through the middle of the upper side and the crossing of the diagonal of the box. The absence of distillation during installation is evidenced by the equality of diagonals. This can be achieved with the help of wedges, lifting one or another side of the box. After leveling vertically and horizontally, the box is attached to the wall at three points from each side: at a distance of 1 m from the floor and 30 cm from the top and bottom of the box. In the wall (against the side of the box), drilled or pierced with a hole with a hole, clog the wooden plugs to a depth of 40-50mm. Install the box and ripped into the tubes of nails, the caps are interinted into wood at least 2 mm. Instead of nails, it is possible to use steel pins with a diameter of 8-10mm, the diameter of the holes below them must be 2-3 mm less than the diameter of the pins.
Clamps during the installation between the wall and the box canopate dry or wet. With a dry method, the gaps are filled with dry palauls, slag glass glass and compact. When wet, materials are wetted in plaster test (it is prepared in small portions - from 0.2 to 0.5 liters). Frozening, wet gypsum expands and grudges tightly to the wall and bar, preventing the clearance from purging.
When installing the strapping of the panel outer door is performed from simple and figured bars. Caleaves are selected on the strapping or on separate bars. They form a groove with a depth of 15-20mm. Where stick to a thickness of up to 50 mm insert.
Internal doors, depending on the destination, can be solid or lattice. Boxes for interior doors are less massive and consist of three vertical bars vertical and top. When installing doors in the interior walls, the openings are performed without quarters. The door frame in partitions put forward in one side of the doorway on the thickness of the plaster so that when installing the platband lay down to the box and wall. When the thickness of the partition is smaller than the width of the door frame, nourishes the thickness of the thickness, equal to the difference of the thickness of the partition and the box. If the thickness of the partition is greater than the width of the door frame, the barn of the corresponding thickness is naked on the inside of the box.
If you need to additionally connect the door bars with brazings (wooden pins), then the door becomes stronger. The diameter of the holes under the brazing is 10-15mm. Begroes are made of solid rocks. The mounting of the bellows is carried out on glue.
Doors are installed on the loop selected in size. Most often, two loops are installed on the door leaf, but in some cases, when the door is made of heavy wood, three loops are installed. In no case cannot be installed loops on horizontal bars door strapping.
Reps and doors are hung on a loop of different designs, more often - half-and-headed and hinged. Half-coat loops consist of two half-hauling; In the same rod, or the axis, in the other - a hinge in the form of a cap. Such loops are always removable, their cards are easily separated. To reduce friction between them, the ring is put on the rod, more often bronze (copper or brass). Each map has three or four screws for screws (on a hinge six or eight holes), and sometimes more. The height of such loops is 75-50 mm, the width of the card is 30-45 mm.
Hinged loops are made by deaf and removable, in the last one on one end of the rod screw the tip. Loop height - 75-25 mm, card width - 30-35 mm. Place such hinges and doors. Hinged smaller hinges are used for the vessels. The sizes of the loops are determined based on the massiveness of products, the size of bars of boxes and strapping.
The rod of the screw must be tightly into the hole of the loop, and its head is in the splashing hole. When the screw is screwed over the splashing hole, the doors will spring and not cover tightly.
When installing, screws with a flat or secret, semicircular or semi-nailed head are used: the first type of screws - for all types of work, the second and third - for fastening the handles, dormit-made locks and other devices, that is, where the protruding heads will not interfere with the dense arrival of the sash Outbinding doors.
When installing or replacing collapsible loops, it is necessary to remember that the loops can be left and right - interconnected. New loops must have the same direction as old.
When installing, to determine the direction of the door, it is necessary to open it on yourself - the door will be left-sided or rightful depending on which hand lies on the door handle. There is a rule that facilitates memorization: the right door opens counterclockwise.
The installation of the loop is performed in such a sequence: the loop attaches to the sash or door at a distance from the edge equal to the loop length. Weat places for loops. The chisel cut out the wood on the thickness of the loop card and attach it with screws so that its axis is parallel to the edge of the bar. Stripping the loop on the sash or door, they are revealed, attach them to the box, tightly pressing to the top bar, and outline on the opened cards, leaving the risks under the loop at a quarter. On risks, they choose wood under the cards of the loops, the places for screws are planned, installed each loop with one screw and check, how the sash or the door is covered. If necessary, make corrections and strengthen loops with screws.
When installing doors in the box, it is especially important to fit the door to a quarter. A hung door should not spring when opening and closing, and freely rotate on the loops.
Handles are also fixed with screws. The slots between the door frames and the wall are closed with boards.
After installing the door block, the canvas are removed from the loops so as not to damage it during the finishing work. At the end of the decoration of the room, the door blocks in the openings of plastered walls and partitions are facing with platbands in terms of the wall plane.
Installing the finished set. The door set usually consists of three elements: the door canvases with a built-in lock and a latch, a doorway with a stopper for doors and loops and platbands, fitted on the joint door to the mustache, the Finnish doors have a serious competition in our market, which is french products, which Different with special grace.
The modern interior door can be made of chip or wood-fiber plates, from aluminum and plastic (PVC), etc. Door boxes are also made from different materials.
In the ready-made door kit, the hardest work is performed at the factory. Jocks and perts are profiled and drilled for assembly. Loops are installed on the doors, the lock is inserted into place. It remains to collect components and install the kit to a new doorway or in the old door, from which the door and fastening of the box were removed. The principles of assembly are the same for all door sets. The difference is to complete the assembly of the package supplied. The box can be in a set of individual elements, separately platbands, and maybe it is all already assembly.
Before, measure the height and width of the opening, as well as the thickness of the wall. Door boxes in sets supply depending on the wall thickness. Before installation, it is necessary to decide which way the door will open the door and whether it will be left to left or right. It is very important when installing the door block - and it depends on your qualifications - correctly put the box in the doorway. If the box is slightly twisted or dear in the opening, the door will not open correctly and close. And you can hardly be able to install the door without damaging its appearance. So, you need to start with the loop side of the box. If this jamb you are correctly installed and dried it tightly, then install the upper crossbar and the opposite cant is absolutely difficult.
In the canvas, platbands and parts of the box facing the room, are already decorated (paint, varnishing, veneer, etc.), the tree facing the inner face of the opening is usually not processed.
The door frame is collected as follows: First, they will connect three sections of the door frame and the door platband, skipping plastic spikes on the shoals in plastic grooves on the pertolock. Then add the components to each other until their corners are connected correctly. Box fasten, inserting the bolts into the drilled holes and tightening them with nuts.
After that, the collected box is put in the doorway. The gaps between the jambs and the wall should be the same on both sides. The platband is tightly pressed against the wall. Using a plumb or level, make sure that the looping jamb stands and does not deviate aside.
Working on the other side of the doorway, insert the seal between the looped jamb and the wall at the level of all three looped pins. In the untreated surface of the looper at the level of each loop, holes are drilled. If the wall is concrete or brick, then drill the wall and insert into the plug holes. The jamb should be installed on the wall of screws No. 10. Screws must be long enough to seize the jamb, seal and go into the wall at least 25 mm
The door sample is made as follows: the door at a right angle to the plane of the opening is lowered by three looped nests, screwed to the door, on the appropriate looping pins of the jamb. Pens and lining for the handles to both sides of the door are installed, closed the door, adjust the position of the loose jamb, and then insert the seal between the jacket and the wall. The second joint to the wall is fixed in the same way.
In order to trim the platband, but the inner edge of one of its sections is inserted into the appropriate groove of the box of the box. If the slot is formed between the platband and the wall, the surface of the platband is adjusted by the plane.
With other sections come in the same way.
Strengthen the platbands during installation as follows: connect three sections of the platbands are similar to the box sections; It is smeared with the necessary glue (PVA, Liquid, Nails, Dap, The Nail, etc.), the unprocessed surface of the box along the jambs and perts, then push the collected platband to the door frame. The inner sidewalls of the platband when installing are tightly pressed to the groove of the collected box. Three struts cut off the bar (or boards) in the width of the doorway. Under the ends of the bars, it is necessary to put a soft cloth so as not to damage the lacquered surface of the platband. Then plunify the struts between the lubricated glue by the sections of the platband. It reliably keep the platband in place until the glue dry.
Doors entrance and interroom. Finnish doors
Pretty popular for many years have been Finnish doors. Previously, they are available only to some people. But now they can be found absolutely everywhere: in cafes, restaurants, in apartments. These doors have already managed to take a certain niche of this market and explore the Russian consumer.
Finnish doors managed to show that they are very reliable and high-quality. Over the manufacturing technology of these doors worked for a long time. And it brought the production of Finnish doors to a new one - the European level. They became sold in all countries.
One of the differences in the Finnish doors is a strict design in a palette with sufficiently cold shades. The abundance of a variety of models allows each buyer, to find what he needs. But some do not want to buy Finnish doors because they consider their design a little "miser."
The most important advantage over other doors is the ease of installation. All the necessary holes are made by the manufacturer himself. The width of the door box is 9cm, the height is 210 cm. These parameters are suitable for Russian apartments, although sometimes it is necessary to cut the door or increase the door himself.
If you decide to give preference in acquiring exactly the Finnish doors, then when you need to take a look at the certificate of conformity issued by the company - the manufacturer and for the presence of appropriate printing and stamp on it itself.
- price and quality are relevant
Did you decide to buy interroom doors? Then think about several points: the price suitable for you, the desired option to open the door, design, size and availability of additional doors similar to design with the doors.
It will not be superfluous to think about the design of the doors. It is necessary to take into account the fact that the wooden doors of Saama expensive, but at the same time, they can become a real interior decoration. Elegance, a variety of forms and service life of such doors (massive doors can be repaired) - speaks for itself. If your goal is to buy interior durable doors and impeccable during operation, you need to know the clear observance of manufacturers of all cycles of the technological process in their manufacture. The quality of the materials used by the masters also plays an unimportant role. To mention high quality, some firms put their product logo. 
Interior doors made of combined materials such as MDF will be cheaper. They look great, durable and in quality are actually not inferior to a wooden door. But plus the fact that their reaction to moisture changes in the room is much smaller. The MDF door depends on the veneer wood breed, which is used for finishing. At the same time, the type of material itself does not affect the quality of the door itself, it gives the door leaf with a shade and texture.
Also there are hollow, so-called cellular filling, doors. The outer panel is specifically formed. Such as mazonite interior doors are less durable and need more neat operation. They exist both already covered with veneer, and simply in the primed form. The second is suitable for people with a more creative approach, because they allow you to paint the interior how to think.
The box for the door can be made of both the array so from the chipboard or MDF. It is a tree, despite its popularity among buyers, less practical. An array can be damaged over time, as well as there is a risk of changing linear dimensions. Modern materials made under the tree not only exceed the physical properties of the array, but also in appearance, sometimes exceed natural wood. At the same time, the technology of installation of boxes of different materials will be completely different.
On interior doors, certification is not provided. And determine the quality of the material on the eye, from which the door canvas is made - quite difficult. Experts recommend buying the door in proven serious firms, or already established and proven brand.
Processed