Modern housing consists of many communications, where the leading place is occupied by electrical wires. They connect not only numerous light sources, but also all appliances, from household to digital. Such an abundance of cable can create a not very attractive picture, and if there are small children in the house, then it can also be dangerous. To prevent any troubles from happening, during the planning of the repair, you must immediately determine where and how to hide the wires in the apartment. Let's consider the most common options that are very popular.
Internal placement
When it comes to major repairs, it is best to hide all communications so that they do not spoil the aesthetic appearance.
Wall
This technology can be applied when the wallpaper is already glued on the wall. To do this, you need to follow a simple algorithm of actions:
- The wallpaper is carefully cut with a sharp knife and folded to the sides, securing with needles.
- With the help of a construction tool, a groove is made where the wire will be hidden.
- Lay the cable in the resulting groove.
- The groove is sealed with plasticine or plastered over with plaster.
- When the solution dries, the wallpaper is coated with glue and glued in place.
Floor
Equally popular is the placement of wires on the floor, or rather under it. In such a simple, but at the same time original way, you can quickly mask the wires. There are several ways you can take advantage of this option.
- Special skirting board. When visiting a hardware store, pay attention to skirting board models with a special niche for cables. In them, the central part will be easily removed; wires can be laid in the recess. This method is convenient and versatile.
- Disguise to the floor. During the repair work, using a perforator, a recess is made in the floor in which communications are laid and then poured with cement.
- Cement strainer. Leveling the floor is a must in almost every apartment. When performing it, it is necessary to stretch the wire in the corrugation, lay it on the floor and pour the usual cement screed on top.
Ceiling
You can even hide the wires on the ceiling, moreover, it will be easier to do than in the version with a wall. There are also several options here:
- Installation of a decorative plasterboard niche that runs along the entire perimeter of the ceiling. The resulting gap can accommodate a huge amount of wires. Experts recommend to fasten all communications into one common highway.
- The stretch ceiling also allows you to hide the wires, but this is the only thing you need to think about before stretching the canvas. The placement method will not make any difference.
Placement behind a stretch ceiling Pay attention! To give the ceiling with a niche an aesthetic and original look, equip it with lighting. Outdoor disguise
If you have no desire to break the created interior and add work to yourself, then you can use equally interesting camouflage methods.
Branch of a tree. Even a small but extra piece of cable can be easily decorated. For this, a tree branch is formed, which is decorated with homemade leaves, flowers and birds. An original idea will update the interior and revitalize the room.
Trees. If the excess wire is too long, then don't rush and cut it. It will be enough to buy special fasteners, look for a suitable silhouette on the Internet and form it on the wall.
Landscape. More complex options can be considered. So on the wall you can "draw" an original panel. The main thing is a clear contrast that will make the idea stand out.
Art object. Since we are talking about electricity, then you can make the original design of the ceiling in the form of a giant light bulb. This structure is fixed to the ceiling.
Power station. In order for the decorative element to perform several functions at the same time, you can depict a simple power plant on the wall, with the help of which parents can teach their children the basics and principle of the power plant.
Highway. The process is more complicated and painstaking, moreover, it will require free time and desire. To create an interesting piece of furniture, it is necessary to cut out all the components from cardboard and, if desired, paint them so that a colorful object comes out. Special blanks can be purchased. Thus, it will be possible to easily mask the wires from the TV.
Fence. Any wires can be attached to the top of the skirting board. But, in order to disguise them, you can cut out small blanks in the form of a fence, which is fixed to the baseboard using double-sided tape. This is an original idea for a children's room, while the fence can be painted in different colors or one specific one.
In addition, communications can be easily hidden behind such items:
- tall indoor plants;
- correctly positioned furniture;
- door platbands;
- carpet covering.
A computer
Most of the cords are located around the computer desk. Here, in addition to the computer itself, there may be other devices that require an electrical connection. All this leads to the presence of not only tangled wires, but also carriers. To decorate them, you just need to turn on your imagination:
- Using clips, self-tapping screws, double-sided tape, all wires are fixed under the table top.
- Any shoe box will hold a large number of wires that will come out of specially made holes.
- The sewn extension sleeve is simply fixed to the desk top so that it will not get tangled underfoot and get in the way of the user.
- A simple cover is also made along the contour of the back of the table, along which the cords will go down to the sockets.
- So that the wires are twisted into one piece, you can tighten them into a hose, which will quickly remove the chaos behind the wall.
- So that the connectors from the devices are not lost, you can use simple stationery paper clips that attach to the side of the tabletop. When it comes to wires from the Internet, experts here recommend switching to modern and innovative technologies, that is, using a wireless network - Wi-Fi. This will allow everyone to connect to the internet no matter what room they are in.
Extension cable box Please note! The shoebox idea can also be used to store chargers for phones, tablets and digital cameras. Moreover, they will all be in their places and will no longer be lost. 
- In the process of masking, it is necessary to mark each type of cable on both sides. Even after a few years, you will not get entangled in a large number of wires and will quickly find the one you need.
- Wires that are used for data or signal transmission (computer, antenna, audio, and internet) must be tied separately from AC mains cables. This will reduce the level of interference and noise.
- The power cable should be short, the longer it is necessary, the higher the risk of electric shock and injury. Even a child or animal while playing can damage it.
- The fabric braid should not be folded, as the fabric with a small break can catch fire and quickly lose its attractiveness.
- The specialized store has a large assortment of special decorative boxes in which you can hide wires. The original design will easily fit into any room interior and will not take up much space.
Device for neat placement of wires Pay attention! Buy and cut off the required amount of wire in fact, so that later you do not think about what to do with the excess and how to decorate it. If necessary, you can implement the most unusual and extraordinary ideas for masking wires in an apartment.
stroysvoimirukami.ru
How to hide wires
The technique in the apartment makes life very easy for its owner, but as it becomes more, the problem of wires becomes more complicated. If you are already starting to panic, looking at the wires snaking across the floor and under the table for a computer, charging a phone, laptop, tablet - do not despair, in this article we have collected for you 7 best ways to hide wires beautifully and put an end to it!1 Bind and Immobilize!
Cables and wires, at least most of them, are located in about the same corner and rarely move. Nevertheless, wires for the computer, gathered in thick tangles under the table, the eternal "noodles" behind the TV, constantly fall under your feet, interfere with cleaning, or even completely fall out of the connectors at the most inopportune moment.
How to hide the wires and secure them at the same time? Try to use building screeds for this: they are disposable, they cannot be removed without cutting, and reusable. They cost a penny, but they can be used to collect wires in bundles, and fasten them to the wall for them.
** highlight: Soul strives for beauty even in the prosaic theme of wires? Get decorative ties! Similar to the leaves, "Leaf Tie" can be ordered online. Similar "Wire Blooms Cable Clips" will allow you to fix the cable to the wall.
2 Binder to help you hide the wires!
The name of this large stationery clip is not familiar to everyone, as well as its other side. He can not only hold papers, but also become a good ally in the fight against wires.
Use them to attach wires to a table or wall, and remove the correct one whenever you like in one motion. Fix them on the table, and pass a usb wire or any other that you often use through them, and they will never get lost or crawl away.
3 Velcro will help to hide the wires: the simplest and most creative.
It is convenient to pull the wires together with special Velcro, the same as on clothes. You can buy them or make them yourself; you can find materials for them in a handicraft store.
4 Hide, cannot be left.
There are many options for how to hide wires that move in one way or another, but what to do with those that lie in one place almost all the time?
In this case, you need to buy a cable channel, often in hardware stores they are sold combined with skirting boards. They will perfectly hide several wires, even if they are quite thick.
Although they have a minus - they must be installed first having got rid of the old baseboards, and the wire laid in them cannot be easily removed. Fortunately, there are alternative solutions.
Such a decorative fence is convenient, looks great and is easy to make. All you need is plywood (thick cardboard or plastic will also work), double-sided tape and cutting tools.
5 Incubator… for charging.
Chargers and power supplies from various gadgets are no less troublesome in the house. Their number grows every year, and sometimes the search for the right charge takes as much time as the process of charging the battery.
To forget about it and no longer meditate on a tangle of tangled wires, removing the necessary charger from it, the charger box will help.
The field for creativity here is huge - only your imagination and ... fire safety can limit you. Yes, you should not neglect this parameter and try to fit all 15 power supplies into a small box: they can overheat and cause a fire, so do not save on the spot in the "charging incubator".
Inside the box there is an extension cord for several inputs. To do this for a couple of minutes, but then you can charge several devices at once without cluttering the table. A shoe box is perfect as a base.
There is another option - to sew a holder for chargers. The design and the number of seats, again, are determined only by your imagination.
"Single" purse for charging a smartphone made of fabric and the same with increased rigidity (a lotion bottle that matches the shape, lined with fabric).
6 How to store wires.
Once you've got all the wires in perfect order on your desk and around your home appliances, it's helpful to know how to store wires. It can be a cord from a lawn mower, a favorite New Year's garland, or even headphones that tend to get tangled with phenomenal tenacity.
The cable harness can be inserted into a cardboard tube from paper towels or toilet paper. Each should be labeled and stored in a large box without getting tangled up. Instead of such tubes, you can use pipe insulation (sold in hardware stores).
The headphones can be wrapped around an old bank card, and the garland can be wrapped around a large piece of cardboard.
7 How to hide wires for a computer and more.
We deliberately placed this method of taming the wires at the end, since it includes all the previous ones. How to connect wires so that you forget about them for a long time? Make them one piece with your furniture! Read on to find out how to get rid of the bad smell yourself.
For example, you can restore order in the wires under the computer table by fixing the extension cord, electrical and signal wires "upside down" or vertically. Special skills are not needed for this, self-tapping screws and a screwdriver are enough. And if you don't want to spoil the furniture, pay attention to the various Velcro clips, of which there are many in hardware stores.
By following these simple tips, you can get your wiring neat and tidy in no time, and get creative with it. Read: How to Make Your Own Decorative Candles - 10 Ideas.
Also read
Comments (1)
style-beauti.com
How to fix a cable duct to a concrete wall
During the construction of a house, the installation of electrical wiring is carried out in a hidden way, under plaster. Complete replacement of electrical wiring, as a rule, is carried out during a major overhaul. In this case, grooves are made in the wall, into which the wire is laid.
But what if there is no opportunity or desire to engage in dusty wall chipping? Or do you need to connect a recently installed powerful electrical appliance, for example, a water heater? In this case, many people choose an open way of laying electrical wiring, and fastening to the wall is carried out using a cable channel.
Types of cable channels
Several criteria are used to classify the channel cable:
- The size. There are small products for laying one wire of a small cross-section or boxes of large sizes, designed to fix up to eight conductors of various cross-sections on the wall;
- Manufacturing material. They produce aluminum, steel and plastic structures. For indoor installation, plastic models are more in demand, and fastening of steel and aluminum boxes is more often used when laying electrical wiring along the facade of a house;
- Location. The fixing of the cable channel can be done in several places. The design of the product is maximally adaptable depending on the installation location. Distinguish between skirting, parapet, trunk and floor models.
Note! In terms of color design, the cable duct most often has a neutral white color, suitable for any finish. Models imitating a wooden structure are also popular.
Installation technology
The main advantage of cable duct for surface wiring is ease of installation. At the same time, the structure can be fixed on any surface: wall, floor or ceiling. The material of the surface is of greater importance: the method of how best to fix it depends on this. Consider the main installation options, as well as the types of surfaces to which the cable channel is attached.
Surface marking
Before starting to fix the cable channel, it is necessary to make markings on the surface: the location of the boxes for electrical wiring is marked on the wall. This can be done with a pencil or chalk and a building level. It is important to maintain horizontal and vertical, because after the installation is completed, the unevenness of the gasket will be conspicuous.
Mounting on self-tapping screws
To fix the box on a wooden wall, use ordinary self-tapping screws. The recommended length is 2-3 cm. This method is suitable for wooden houses, baths and other structures. Also, the self-tapping screw mount is suitable for walls sheathed with wooden clapboard.
When performing installation, holes are pre-drilled in the bottom of the box, into which self-tapping screws are then screwed. In plastic structures, holes can be made directly with a self-tapping screw when fastening. The optimal distance between the mounting points is 30-50 cm, depending on the expected load on the cable channel (the number of wires in the electrical wiring placed in the box).
Fixing with dowels
Installation of cable channels on a concrete surface requires a more serious approach and additional tools. This will require plastic dowels and a hammer drill or hammer drill to make holes in the concrete wall. This method is suitable for installing any profile: both metal and plastic, indoors or outside the building. The order of work is as follows:
- Holes for fastening are drilled in the lower part of the box. The distance between them, as in the previous version, is 30–50 cm;
- Then the cable channel is applied to the wall along the previously marked line;
- With the help of an awl or a nail, the location of the fasteners is marked on the surface of the wall;
- Then, according to the marks in the wall, holes of the required diameter are drilled with a perforator, into which plastic dowels are hammered;
- After that, it remains to fix the profile with self-tapping screws.
You can also use dowel nails, which are hammered in, to secure the electrical wiring box to the concrete surface. But this option has a significant drawback - if it is necessary to transfer the structure, certain problems arise with the dismantling of such dowels.
Glue method
Another option for fixing the cable channel is to use mounting glue for fixing. Most often, the adhesive composition "liquid nails", produced under the Moment trademark, is used for these purposes. Such glue is produced in tubes for a mounting gun or in ordinary tubes for manual application.
The adhesive installation method is used to attach cable channels to drywall, PVC wall cladding (plastic lining or panels), as well as in bathrooms on ceramic tiles. It is worth noting that only plastic wiring boxes are suitable for this method, since their weight is minimal. It is also desirable that the number of wires laid in the cable channel is minimal and does not create significant loads on the structure.
The technology of the adhesive fixation method is as follows:
- An adhesive is applied to the back of the profile. The adhesive spreads in waves to ensure maximum bond area;
- Then the cable channel is carefully applied to the wall along the marking line and immediately removed;
- After 2-3 minutes, when the glue starts to dry, the strip is reapplied and firmly pressed for several minutes.
After the adhesive has completely set, additional fixation is made in problem areas. For fastening, use small screws or hammer in nails.
To facilitate the connection of the profile, use the additional elements offered by the manufacturer: T-shaped and corner structures, connectors for strips, various elbows and other accessories.
For the installation of sockets and switches, it is best to use overhead versions of these products or use models of boxes with built-in structures.
Separately, we note that the installation of external wiring is carried out last, after all the finishing work has been completed.
voltland.ru
How to fix the wire to the wall?
The wires are laid in different ways. Or they make a groove in the wall, and an electric wire is laid there. Can be used over plaster, but not over paper wallpaper. They fix it with special brackets bought in a store, or by cutting from metal plates, nail them, put a wire on them and pull the ends together. Wiring is often placed in beautiful cable channels so that they do not spoil the appearance of the room.
If the wire is stationary and does not imply periodic movement, then it is better and safer in the cable channel. These are plastic boxes made of low-burning materials, which have both a neutral white color, and many others - like wood, ivory, etc. In such a box, the cable does not break, does not press on and the maintainability of the entire network increases.
They used to hammer in a nail, but those days are gone. In places where wire is sold, special fasteners for wires are available for sale. They are selected based on the thickness of the wire and look approximately as follows
It's very simple - to stick it! You can even use wallpaper glue! And if it is not available - your own saliva, after eating eggs or even oatmeal! Eat a bowl of oatmeal (or pearl barley - it doesn't matter) then abundantly moisten the wire and the wall with your saliva and calmly stick the wire to the wall - if your saliva is not viscous enough, you can drive in a nail or use a puncher, the main thing is to choose the right time to spandor the wire to the wall! The most effective is after midnight and certainly in the Waxing Moon Phase! Calmly, without getting nervous, turn on the perforator (you can not slobber it) and, having estimated the position of the wire, as you like, vpend it into the wall! The main thing is not to be mistaken in the Moon Phase! Otherwise, the wire may stick fragmentarily and fall off the next day! And this is a completely different story! 🙂
In addition to all these methods, you can use regular nails with a length of 20 millimeters. Hammer in half of the nail path along which you want to lay the cable. Use the pliers to bend them 90. Hold the cable and hammer the nails into the top one at a time. You will get a fastening in the form of staples.
Wires and cables can be attached to the wall with special wire fasteners, but it will not look very neat.
More civilized is to lay the wire in cable channels that are attached to the wall and only then the wire is laid in them.
There are several ways to fix the wire to the wall. It all depends on the purpose of this fastener, permanent or temporary, on the purpose of the wiring being laid, on the requirements for its appearance. If the wire is attached to a concrete or brick wall, it is best to use cable ducts, the choice of which in the store is very large, of the most different sizes. There are also special corners, adapters or plugs for them, as for skirting boards. It looks aesthetically pleasing and quick to install. The cable channel is attached to the dowel-nails using a puncher, after about 40-50 centimeters. There are more options for a wooden wall, these are the same cable channels, plastic clamps shown in the early answer, homemade clamps made of tin (they are first cut into thin strips, then nailed to the wall along the cable route, and then the cable is laid and clamped on both sides ), special retro porcelain insulators that used to be found in every home, but now they have become a vintage piece of furniture. Often they try to hide the wire in plastic skirting boards if they run along the wall.
info-4all.ru
How to remove wires in an apartment and hide them creatively.
Every person strives for excellence. He is trying to create something beautiful around himself. He equips his home. Tries to make it warm and cozy. Carries out renovations, creates a beautiful interior, furnishes with furniture and equips the room with equipment. The operation of modern technology is impossible without wires. Television, electrical and Internet wires often run around the perimeter of the entire room, thus causing a lot of hassle. The owners often stumble over them. In addition to making life difficult, they also greatly spoil the design of the room. What to do in this situation and how to remove the wires in the apartment, getting tangled underfoot?
An easy and common way to remove wires in an apartment is to hide them in a baseboard. Its main feature is that it contains a space intended for laying wires. You can buy it on the market or in any construction supermarket. The skirting board is attached to the wall using self-tapping screws and dowels.
The cables along the wall are hidden in the plastic channels of the baseboard. Skirting boards come in a variety of colors and sizes. Therefore, you can easily choose the right plinth, which will allow you to hide all communications in it, and at the same time look nice.
After laying the existing wires, the channel cavity is closed with a special decorative strip. This method is distinguished by its reliability and cable protection is guaranteed from animals that like to scratch and gnaw on everything.
There is another method to hide the wires in the floor. When carrying out construction work to level the floor with a screed. The wires are packed in a special sleeve and filled with cement mortar. When hardened, the cords are successfully hidden under it.
How to remove wires in an apartment on the wall
When carrying out repair work, the wires are deepened inside the wall. This is done with a grinder. Two grooves are cut in the wall, after which a part of the plaster between them is knocked out with a puncher. Thus, a strobe is obtained. All communications fit into it and are covered with alabaster. It dries quickly and fixes them. They do the same with the places where the sockets will be located.
How to remove the wires on the wall after the repair is completed? The box will solve the problem. It is necessary to attach them to the wall with glue or screw them with screws, and then put the cable in them and close them with the lid.
If the socket is located close to the door or you do not know how to remove the wires lying in the doorway, then door trims are used to mask the cable. It is necessary to remove them and place the wires there, put them back.
It is easy to remove wires in an apartment using suspended or stretch ceilings. A metal, wooden or plastic frame is specially made and fixed to the ceiling.
The cables are bundled and laid inside the frame or on top of it.
In order for the wires to gather together, you can use insulating tape or plastic clips. If there are few wires, use a plastic sleeve. Then the stretch or false ceiling will hide everything. But if you cannot remove the wires yourself, you can contact trusted craftsmen and they will help you.
How to remove wires in an apartment using furniture
You can cover the wires in other simple ways. With furniture. If there is a lot of furniture in the room, you can arrange it so as to hide the wires as much as possible. At the same time, nothing radically changes, and the room after such a rearrangement will look different.
The presence in the house of a personal computer and org. technology, implies a large accumulation of wires at the table.
The correct solution would be to purchase a special plastic cable box. It perfectly accommodates wires and an extension cord. When buying a simple box, you can hide it under the table, but if it is bright, colored, you can use it as a decorative addition.
How to remove wires in an apartment - creative ways
If you wish, you can not hide the wires at all. One has only to include a little imagination and ingenuity. And the interior design of the room will change beyond recognition.
Do not rush to cut the length of the wire. Its size can be used for creative ideas. Creation of an ornament, pattern, bird, dragonfly. The cords can be hidden by using climbing plants. Run a twig along the cable and the wire will turn into a decorative element. It will look beautiful, and the presence of fresh flowers will refresh and add coziness to the room.
Decorative staples are also sold. They differ somewhat from simple ones in their appearance. Decorated with birds, flowers and all kinds of figurines. With their help, you can make a tree from an ordinary wire, with a bird sitting on it or a flower, with a beautiful butterfly.
If you can't find these staples on the market, you can use vinyl decals instead. With their help, create a composition and the cable will become part of it.
Using the advice of the site's article, everyone will be able to choose an acceptable way for themselves, thanks to which they can achieve a result. And the problem - how to remove the wires in the apartment will disappear forever.
Unfortunately, wireless technology has not yet become widespread in offices and homes. This means that in the near future a bunch of annoying wires on the table will not go anywhere. Here are some tips to help you clear the clutter and keep your cables out of sight.
In contact with
Classmates
1. Hide the extension cord with chargers in the box- An extension cord with chargers constantly gets in the way on the table or underfoot, collects a lot of dust, and looks unaesthetic. Dealing with this problem is very simple: take a nice box, poke a few holes in it and hide all the wires and cables there.
- There are also ready-made solutions, for example Plug Hub from Quirky. This is a box made of hard plastic with a rubberized bottom. There are three cable holes on the top, and on the inside there are three fasteners that can be used to wrap cords that are too long. Plug Hub can be placed on the floor or mounted on the wall.
2. Fasten the wires under the countertop
- To secure the wires and extension cord under the table, you will need binders and screws (they should be at least a quarter less than the thickness of the tabletop in length, otherwise they will go right through and the table will be damaged). First of all, attach an extension cord under the tabletop, preferably in the middle of the table or closer to the wall.
- Then fix the binders in the right places with screws. Connect everything you need to the extension cord and collect the wires with clamps. Visually, the table has become much cleaner and more accurate.
- There is an easier option if you don't need to hide a lot of wires. This will require a construction stapler. To prevent the long wire from the lamp from dangling under your feet, carefully secure it with paper clips at the table leg.
The small extension can also be secured with staples. For thicker wires, it is better to use special clamps (for example, such).
- Don't you like staple clips? Regular screeds will do. Use cable ties to secure the wire to the table leg. The wires that run along the floor can be covered with plastic or a plank to match the floor.
- The extension can be fixed under the worktop with a wide Velcro: fix it to the back of the worktop with screws, and then attach the extension. To keep the wires from dangling under the table, run them through cable ducts - you can buy them at any hardware store. The canals themselves can be fixed with electrical tape or ordinary plaster.
- Correct organization of the wires will help to get rid of confusion in the wires.
To get started, collect cords from phones, players, game consoles, tablets around the house.
Then take the boxes (preferably prettier), place cardboard dividers inside them, sign the place for each cable (so that you do not get confused later) and arrange everything neatly.
To avoid tangling the wires themselves, use regular cable ties.
4. Keep all necessary wires close at handWe can not hide all cables in the box: we need some of them almost constantly.
The solution is simple: attach them to the edge of your desktop so that you can reach out and connect the device to the desired wire if needed. Sugru will help us with this - plasticine-rubber and one of the most irreplaceable things in the household.
Roll small balls out of Sugru, fasten to the table support. Then use a clerical knife to remove some of the plasticine (carefully, try not to deform the balls too much).
Life hack: so that the plasticine does not stick to the blade, rinse it with soapy water first.
Then tweak the shape a little with a sushi stick or toothpick to create neat depressions (they should be slightly wider than your wires).
Everything is ready, you can fix the cables.
- There is an option for those who know how to work with wood. A small block of holes will help you organize all the wires on your desk.
- The simplest solution is to run the wires through the binders attached to the tabletop.
5. Don't hide the wires
Seriously, if you get down to it creatively, cables can be an interesting decor element. For example, you can fix the wire to the wall using special clamps. Why hide a wire when you can attach a bird to it?
You are here now - home - All about repair:
When you are going to hang something on the wall, it is not a question at all!
You will need a hammer drill or hammer drill. A couple of dowels. Level, hammer, tape measure.
If this is a shelf or cabinet, then we put it in that place and roughly mark the level of the hole. Well, then it's quite simple, we measure the distance between the holes on the shelf or cabinet.
We mark under the first hole, take a level - draw, take a tape measure, set the distance. The intersection of a straight line in level and distance on a tape measure will be your second hole!
If there are several shelves or cabinets, then we do this:
We start, either from the extreme right point, or the extreme left point, drill, hammer in the dowel, tie the thread, level it. In the place where the person holds the thread, it is required to somehow fix it. Drilling and fixing to the dowel is possible only if the hole from the rough dowel is either hidden by a shelf or cabinet.
An ordinary dowel 6 x 40 will withstand at least 50 kg per cut, in a concrete wall. I think that you will not have more than 100 kg in one cabinet!
Why is all this, how to hang a shelf, or how to hang a cabinet is such a simple operation that it’s even somehow boring!
But here's what I wanted to tell you.
How to accurately hang the first time?
How to hang something with no direct access to its holes !?
Imagine a situation that you measured, hammered a nail, and missed the size, for various reasons, and it is already impossible to drill nearby !?
There was such a situation !?
Since I worked a lot both in construction and as a carpenter and joiner, I had to see a lot!
And often this very situation turned out to be practically insoluble the first time!
But there is a way that is ingenious, like the simplest things! And I remembered this method when it became necessary to hang an extension cord!
Hang the extension cable for your computer on the back of your desk the first time and exactly where you need it! The top table top extends slightly beyond the back panel, so we have a limiter!
We need to make a template.
1.Select self-tapping screws so that they fit freely into the hole of the hanger.
2. In this case, I had a thin cardboard lying around.
ATTACHING THE EXTENSION
It is more convenient than a simple sheet, because the screws will hold better there.
3.Insert self-tapping screws and move them to the extreme point of the hanger,
4. We take the cardboard, and aligning on one of the sides, press on the cardboard so that the screws appear on our side.
5. We take out the cardboard with self-tapping screws, put it in the place where our object should be located, in this case the extension cord.
6. We wrap the screws, tear out the cardboard, adjust the screws in height.
7. We put on the extension cord.
Here's what we got, fast, simple, accurate and the first time! The story turned out to be 10 times longer than the process itself !!!
How to hang up a router.
Using absolutely the same technology, we will attach the router in the place where it is needed on the back panel, or on the wall, but the first time.
In this case, plain paper was used as a template!
Here is our router hanging on the back of the table! Very simply cheap and cheerful!
Before installing electrical wiring in a new apartment or before replacing the wiring during a major overhaul, any owner is faced with a choice of how many and what outlets he needs to install in each room. In modern apartments, sockets are rarely installed one at a time, usually two, three, and in some cases even four electrical outlets are placed side by side. For example, at a workplace with a computer, it is better to install 3-4 sockets, otherwise you will not be able to do without an extension cord.
Practice shows that there are never too many sockets. If we need to install two sockets side by side, then we have a choice - to install two single electrical outlets in a two-post frame or one double electrical outlet. The Florence series features double sockets and multi-post frames, so both options can be implemented. What should you choose?
- Double sockets are designed to instead of one old socket, one double socket could be installed into the existing socket.
Home Ideas: How to Hide Wires
This allows you to double the number of outlets for a cosmetic renovation of the apartment. For this, double sockets have been developed.
- The price of a double socket is less than the price of two single sockets in a two-post frame, let us make sure of this using the example of white or beige sockets of the Florence series.
1. Price calculation for two single sockets in a two-post frame
2. Calculation of the price for the alternative - for a double socket
You can mount the wiring so that powerful electrical appliances are connected to each single outlet, i.e. so that a current of up to 16 A flows through each. But for this, it is necessary that the sockets are either powered through two separate lines with cables of the usual cross-section for connecting sockets (2.5 mm2), or powered in series through a cable with an increased cross-section. As a result, it is possible to achieve that the total maximum current, which can flow through two single electrical outlets, would be 32A. This cannot be done by installing a double electrical outlet.
Summing up, we can say that double sockets are irreplaceable if we are faced with the task of increasing the number of outlets in the pre-installed socket boxes. Basically, this is relevant when replacing outlets in the process of cosmetic repairs, if the wiring is not being replaced with the installation of new socket outlets. Single sockets under the multi-post frame look more aesthetically pleasing than double sockets and give you more freedom of choice. This option is suitable for a major overhaul of an apartment with replacement of wiring or for furnishing an apartment without finishing in a new building.
|
Click on the picture to enlarge. A great solution to get rid of the "charger" cables scattered all over the floor came from a Japanese company: they created a SocketDeer socket with antlers attached to it! On these horns, you can put, for example, a mobile phone and plug its "charger" into an outlet. The cable can be wrapped around the horns so it does not hang down to the floor.
A great travel solution, the Belkin Mini Surge tee allows you to take one USB charger with you on the go instead of several. In addition, this device provides you with additional power outlets and surge protection wherever you are: in a hotel room or at the airport. Mini Surge is equipped with three regular outlets and two USB ports through which you can recharge various devices. The Mini Surge can be rotated 360 degrees around its axis, which will make it convenient to place it in any working environment and not block other outlets. Woofy
The price of this plastic dog just doesn't fit in your head! However, if you are looking for some sophisticated way to store cables, then perhaps Woofy will interest you. The cables hide in the "belly" of this almost half-meter dog, and are pulled out of its hind legs.
On October 9, 2008, a video appeared on DL.TV site in which an anonymous viewer from Seattle brags about his incredible invention: a wireless office. You can watch the video. All cables are routed inside PVC boxes that form the contour of the table and go to a wall outlet. There are no wires above or below the table. Serious DIY project.
The 40cm plastic box serves the same function as the Woofy but only costs $ 29.50. Of course, it's not as original as the $ 250 plastic dog, but inside this box you can hide a whole extension cord with all the dangling cables.
Can't stick two power supplies side by side? The situation can be corrected with a rotating wall socket. It will take you 10 minutes to set this position, but then you can plug two bulky "chargers" into the outlet, which did not fit anywhere else, since you can fix them at an angle, and not directly above each other. Sometimes extra centimeters can play a big role.
Such sockets have not yet been produced, but the idea is worthy of attention. How many times do you pull the plug out of the outlet (to save energy, free up space, or temporarily plug in another device) and drop it on the floor, where the cords get tangled and everyone stumbles about them? After all, it’s not safe. The way out is obvious: you just need to hang unused plugs on the holders of the sockets themselves. As soon as possible, such sockets would appear on sale!
Some of the products presented in this review are a little strange, but SocketSense is a really practical thing. How convenient it is to use a model instead of a regular extension cord that can be pulled out (from 33 to 41 cm) to suit any fork configuration. For some users, the most important thing will be how this surge protector looks - completely ordinary, with six slots.
If SocketSense looks like a completely normal upgrade to a standard surge protector, designed to allow you to connect more "chargers" of a non-standard size, then PowerSquid looks strange. But this makes a lot of sense. PowerSquid is highlighted in blue in the dark so that you can see where to plug the plugs under the table. Thanks to its flat shape, it can be hidden behind furniture. PowerSquid also protects the telephone line. And the most important thing: all the sockets are located on separate flexible wires, so they do not interfere with each other.
The author of this idea has not yet found a manufacturer who would undertake to bring this project to life. The bottom line is to stretch the wires along the baseboard, but instead of attaching them to the wall, you can hide them behind a decorative fence: the cables are not visible, and at the same time they are easily accessible.
A charging base for the whole family. Kangaroom will make sure that you always know where your phone, camera and other devices are: the Kangaroom splitter hides in a special box that is mounted on the wall in a prominent place. If your phone is in this charging base, then you will never lose either your phone or its charger. |
Even some eight or ten years ago, a surge protector, in the eyes of most of our fellow citizens, was exclusively a computer attribute. In those days, when purchasing such a device, the buyer carefully and for a long time studied its technical characteristics in order to choose the really best one offered by the sellers. At the same time, not much attention was paid to the appearance of the product, in part due to the fact that in those days most surge protectors looked almost the same. But times are changing. And today, surge protectors are not at all an exclusively computer attribute, but have become an ordinary and familiar household device. The modern buyer is no longer as attentive and picky about purely technical characteristics as it was before. In addition, surge protectors in everyday life are mostly viewed as extension cords with a bunch of output connectors and a switch, rather than as a serious device for filtering the supply voltage. Accordingly, the main attention of the buyer is focused on such parameters of the purchased product as ease of use, appearance, and functional equipment. It is from this point of view, in this material, that six surge protectors will be considered. I hope that this will help some to broaden their horizons and see that not all filters are the same and are only "a piece of wire with a box with connectors hanging at the end."
According to the manufacturer, Pilot-S is a cost-effective solution for protecting office electronics. In fact, the only thing that this filter will do well is to protect the user's network from possible short circuits in the power circuits of the equipment connected to it.
The filter in question is primitive both outside and inside. The network cable, the length of which is 1.78m, ends in a simple, no frills, housing (size 373x47x46 mm). In turn, the case carries a backlit power switch, a fuse reset button, and six connectors for connecting consumers. Five of them are quite modern, that is, with grounding. The sixth connector is not grounded and is made for compatibility with old-style plugs. All connectors are located almost close to each other, which may cause some problems for the user. I mean the case when the equipment is powered by an external power supply unit whose dimensions, most often, exceed the dimensions of a conventional mains plug.
Accordingly, when connecting such a power supply, the user will not be able to use the adjacent connector. In addition to this, Pilot-S connectors do not have so-called "childproof". By the way, the child can also disassemble the housing of the filter in question without any problems. To do this, he does not even need a Phillips screwdriver, because the case covers are tightened with ordinary furniture screws, the heads of which almost protrude beyond the boundaries of the case. Only one of them is recessed so that a plasticine seal can be placed on top of it, made in the best traditions of Soviet electrical appliances.
I hope that you can still convince your child that there is absolutely nothing inside the filter that deserves even a drop of attention. Actually, this is actually the case, because in addition to the switch and fuses, the filter consists of one single container. We are not now comparing the characteristics of the filters, but I think it is not difficult to imagine how "serious" such a filter is.
Hopefully you've already appreciated the Pilot-S in question. And, in my opinion, the last thing left to consider is the possibility of attaching this filter anywhere. For this, its design provides two lugs with holes. Unfortunately, the shape of these holes does not allow hanging the filter housing on an existing screw, for example, in the wall. That is, to fix the Pilot-S on any surface, you must first install it in the place of attachment and only then fix it with a screw, screw, or whatever you will fix it there. The design of the case does not provide for any other options, which cannot but grieve.
This model is no longer as economical as the Pilot-S discussed above. The electrical circuit has become more serious and has grown to the LC filter that has already become traditional in such devices. True, the manufacturer managed to save money. Instead of six output connectors, as was the case with the Pilot-S filter, in this case we have only five. Four of them are grounded and one without it. But, compared to the younger model, the location of the Pilot-GL connectors is more convenient for the user, since the universal connector (the one that has no ground) is 11mm apart from the rest. Of course, not a lot, but if not very large external power supplies of the equipment are included in it, then the neighboring outlet will still remain accessible to the user.
In comparison with the previous model, the Pilot-GL has improved not only the filter circuitry, but also the indication. Thus, in addition to the illuminated power switch, the Pilot-GL has an additional green LED. It glows if everything is in order with the device. If, as a result of an overload or short circuit in the filter, the protection is triggered, the LED will go out. In this case, the mains switch will continue to light, indicating the presence of voltage at the Pilot-GL input. I must say that this feature is sometimes very useful.
That, in general, is where all the positive differences between the Pilot-GL and its younger brother end. Everything else, unfortunately, migrated from the younger model to the older one without any changes for the better. The network cable remains the same length (1.78m). The output connectors are not "childproof". The housing covers of the device are tightened with exactly the same screws as in the Pilot-S. True, there are two more lugs for attaching the filter. But, the holes in them, like in the Pilot-S, do not allow hanging the filter housing on a screw or screw already screwed into the wall, for example. In general, in my opinion, the Pilot-GL is definitely better than the simpler model described earlier. But, until the final conclusions are still far away, and therefore let's move on to the consideration of the next filter.