The "A" series alarm control and security devices are effective and inexpensive equipment for equipping small objects with reliable state-of-the-art security systems.
Unlimited software settings- a distinctive feature of the devices "A6" and "A16-512". Specialists have the opportunity to arbitrarily simulate the nature of work and various modes of control of devices connected to the devices. This provides a number of advantages over similar equipment, especially in those cases when it is necessary to solve complex problems.
Flexibility in programming allows not only to simulate the operating modes of external devices connected to the device. It makes it possible to group loops into zones (groups) in any combination, which provides convenience to the user when arming and disarming the premises.
Different ways to manage security zones. You can choose to arm and disarm the premises: using TouchMemory keys, proximity cards Proximity or digital codes entered from the keyboard.
Multiple alarm mode. The device turns on the siren every time an alarm event occurs at the controlled object. This is essential for those cases when the system operates autonomously at the facility without transmitting signals to the control panel of security structures.
Work as part of centralized monitoring systems. The devices provide the ability to transmit messages to the central console about all events occurring at the facility, as well as about the state and operating modes of the equipment. For this, different communication channels can be involved - a radio channel or / and busy lines of the city telephone network.
Network options for the operation of devices. If one device was installed at the object, the object continues to grow and the resources of this device are no longer enough, the new task is solved simply - by combining several autonomously working devices into a single system with the output of information from all devices in the system to one control panel.
Reliable switching units of uninterruptible power supply. All devices "A6" and "A16-512" are equipped with built-in powerful power sources 220V / 12V and have a place in the case for installing a rechargeable battery. Power supplies provide charging of the battery and its disconnection from the device in case of deep discharge.
Access control and management function. This function, built into the device, allows you to limit the access of unauthorized persons to certain rooms of the facility at minimal cost. Supplements the security alarm in the daytime when the facility is not armed, and also allows you to control the use of working time by employees at the facility.
Profitability. The use of devices "A6" and "A16-512" gives a significant economic effect due to the absence of unjustified redundancy of equipment at the facility and savings on installation and maintenance of the system.
Manufactured by OOO NPK MIKROFOR (Russia)
Thermohygrometers IVA-6A and IVA-6N are self-contained portable devices and are designed to measure relative humidity, temperature and atmospheric pressure (optional) of air in residential, warehouse and industrial premises, as well as in a free atmosphere.Thermohygrometers IVA-6A, IVA-6N consist of an indication unit and a measuring transducer.
In the IVA-6A thermohygrometer, the measuring transducer is connected to the display unit with a flexible cable about 1 meter long, which allows you to control the humidity and air temperature in hard-to-reach places, for example, in ventilation ducts.
In the IVA-6N thermohygrometer, the measuring transducer is installed on the display unit. Thermohygrometer IVA-6N can be mounted on a wall using a bracket.
Thermohygrometers can be used:
- for measuring microclimate parameters in museums, archives, libraries, pharmacies, testing laboratories, in clean rooms of the pharmaceutical and electronic industries
- for certification of workplaces in labor protection centers and TsGSEN
- for air humidity control in the printing industry
- to control the storage of products.
IVA-6 instrument designations when ordering:
- IVA-6A: with a remote probe on a cable without recording measured values and a channel for measuring atmospheric pressure.
- IVA-6A-D: with a remote probe on a cable without recording measured values, with a channel for measuring atmospheric pressure.
- IVA-6A-KP: with a remote probe on a cable with recording of measured values to a memory card (microSD), without a channel for measuring atmospheric pressure.
- IVA-6A-KP-D: with a remote probe on a cable with recording of measured values to a memory card (microSD) and a channel for measuring atmospheric pressure.
- IVA-6N: with a built-in probe without registration of measured values and a channel for measuring atmospheric pressure.
- IVA-6N-D: with a built-in probe without registration of measured values, with a channel for measuring atmospheric pressure.
- IVA-6N-KP: with a built-in probe with registration of measured values to a memory card (microSD), without a channel for measuring atmospheric pressure.
- IVA-6N-KP-D: with a built-in probe with registration of measured values to a memory card (microSD) and a channel for measuring atmospheric pressure.
Additional accessories for thermohygrometers IVA-6A and IVA-6N:
| Bag for storage and transportation of thermohygrometers IVA-6A (N) | |
| Bracket for mounting IVA-6A (N) on the wall | |
| KU-1 cable for using the built-in IVA-6N probe as a remote | |
| Mini USB-A cable for reading data stored on a memory card via a USB port and configuring the thermohygrometer |
|
| Protective cap ZKF-1 made of porous fluoroplastic to protect sensors from dust and aerosols |
The metrological characteristics of the IVA-6A and IVA-6N thermohygrometers are almost the same, except for the temperature measurement range: from -20 to 50 ° C for the IVA-6N thermohygrometer and from -20 to 60 ° C for the IVA-6A thermohygrometer, which is caused by permissible operating conditions display unit.
When the KU-1 extension cable is connected, all the metrological characteristics of the IVA-6N and IVA-6A thermohygrometers become exactly the same.
The liquid crystal display of the IVA-6A and IVA-6N thermohygrometers continuously displays the current measured values of temperature and relative humidity. The update period is 60 seconds. When you press any button, the thermohygrometer switches to the "fast" measurement mode and the period of updating the readings on the indicator is 1 s. After 30 seconds, the period of updating the readings on the indicator returns to the value of 60 seconds.
The time of continuous operation when using alkaline cells with a capacity of 2 A * h and turning on the "fast" measurement mode no more than 1 hour per day is at least 1 year.
The thermo-hygrometer calculates the dew point (frost) temperature from the measured temperature and relative humidity.
At freezing temperatures, the instrument can display the relative humidity value over water or over ice.
Thermohygrometers IVA-6A, IVA-6N are produced in 2 modifications:
- without a channel for measuring atmospheric pressure (IVA-6A, IVA-6N, IVA-6A-KP and IVA-6N-KP)
- with a channel for measuring atmospheric pressure (IVA-6A-D, IVA-6N-D, IVA-6A-KP-D and IVA-6N-KP-D)
Units of measurement of atmospheric pressure "hPa" (hectarePascali, 1 hPa = 100 Pa = 0.1 kPa) or "mm Hg. Art. " (millimeters of mercury column) are selected by the user when configuring the thermo-hygrometer via the USB port.
Thermohygrometers IVA-6A, IVA-6N are produced in 2 versions:
- with the registration of measured values on a microSD memory card and the ability to read the accumulated data through the USB port (IVA-6A-KP and IVA-6N-KP)
- with disabled measurement value registration function (IVA-6A and IVA-6N)
In thermo-hygrometers with disabled registration function (IVA-6A, IVA-6N, IVA-6A-D and IVA-6N-D), the registration function can be activated by the user using a key purchased from the supplier of the device. The activation instructions and the key are supplied on the memory card or sent by e-mail (in this case, the consumer purchases the memory card himself).
A slot for inserting a memory card and a mini USB connector for connection to a personal computer are located on the upper end of the thermohygrometer display unit.
The thermo-hygrometer uses standard removable memory cards to record measured values of relative humidity and temperature in real calendar time. microSD... A memory card for devices with activated data logging is included with the device. The program is supplied on the same card DataLogger.
The number of records of measured values of humidity and temperature is 100,000 per 1 MB of memory card capacity, which provides continuous data recording for the entire service life of the battery set.
The accumulated data reading from the thermohygrometer is carried out in two ways:
- from a memory card via a card reader
- via the USB port of the thermo-hygrometer
Software DataLogger provides information reading from a memory card, forms a data archive for each thermo-hygrometer, creates text and graphical reports.
The memory card can be installed in any thermo-hygrometer, since at the time of installation a file is created on it containing information about the device number.
The data written to the card is encrypted to prevent the possibility of falsification.
Thermohygrometers IVA-6A and IVA-6N memorize the minimum and maximum values of humidity and temperature, the time and date of these events.
For low light use, the user can turn on the indicator backlight by pressing the "" button. The backlight is turned off by pressing the "" button again or automatically after 20 seconds. The brightness of the backlight is adjustable when configuring the thermo-hygrometer via the USB port using the DataLogger software.
Thermohygrometers have audible and visual indication that the measured values of relative humidity and temperature are outside the set (using the DataLogger program) limits.
When operating the thermo-hygrometer in highly dirty conditions, it is recommended to use a protective cap made of porous fluoroplastic to protect the sensors from aerosols, dust and condensation.
The use of a protective cap prevents the deterioration of metrological characteristics when the surface of the moisture sensor is contaminated.
Specifications
| Measurement range of relative humidity,% RH | 0…98 |
| Permission | 0,1 |
| Limits of the basic absolute error of measurements of relative humidity at a temperature of 23 ° С,% RH | ± 2% (in the range 0 ... 90%); ± 3% (in the range 90 ... 98%) 2 |
| Temperature measurement range, ° С | -20…601 |
| Permission | 0,1 |
| Limits of permissible absolute error of temperature measurements, ° С | ± 0.3 |
| Measurement range of atmospheric pressure, hPa | 700…11003 |
| Permission | 0,1 |
| Limits of permissible absolute error of atmospheric pressure measurements, hPa | ± 2.5 |
| Time constant: | by relative humidity, min, no more than 2, by temperature, min, no more than 5 |
| Overall dimensions, (L x W x H), mm: | indication unit (IVA-6N) 25 x 70 x 135 (25 x 70 x 175); measuring transducer Ø 16 x 165 |
| Weight, kg, no more | 0,4 |
| Nutrition | 3V (2 AA batteries) |
2 metrological characteristics at a relative humidity above 90% are provided only with a short-term (no more than 2 hours) storage of the converter under these conditions.
3 only for thermo-hygrometers in corresponding modifications.
No. 46434-11 in the State Register of Measuring Instruments of the Russian Federation
"Minsk 2011 CONTENTS LIST OF ACCEPTED TERMS AND ..."
Receiving and control device
security and firefighter "A6"
Manual. Part II
RUIV 170100.000 RE
Programming the device
Revision 7.03
Part II (programming with VPU-A-06 and PR-1) edition 7.03 April 2011
1. GENERAL PROVISIONS
2 Description of the configuration parameters of the device "A6"
2.7 User Keys
2.7.1 Keys "Master"
2.7.2 Keys "GZ"
2.7.3 Keys "Fitter"
2.7.4 Key "Master"
3 DESCRIPTION OF PROGRAMMING USING THE KEYBOARD VPU-A-06 ................ 18
3.1 General requirements
3.2 Description of the remote control panel VPU-A-06
3.2.1 Purpose of the remote control panel VPU-A-06
3.3 Connecting VPU-A-06 to the device and preparing for programming
3.4 Programming the configuration of the "A6" device using VPU-A-06
3.4.1 Menu of LCD keypad VPU-A-06
3.4.2 Registration of instrument ID numbers in the VPU-A-06 memory
3.4.3 Mode of programming the configuration of the device "A6" using the LCD keypad VPU-A-06
4.1 Programming panel PR-1
4.2 Purpose of the PR-1 remote control keys
Control Panel A6 Operation manual. Part II (programming with VPU-A-06 and PR-1) edition 7.03 April 2011
LIST OF ACCEPTED TERMS AND ABBREVIATIONS
ASOS "Alesya" - automated security alarm system "Alesya".ASPT is an automatic fire extinguishing system.
ATL - subscriber telephone line.
GTS - city telephone network.
Standby mode - the operating mode of the device after removing all received signals, in which the device as a whole and its additional devices are able to receive and transmit the "Alarm", "Fire", "Attention" and "Fault" notifications.
IO - burglar detector.
IP - fire detector.
IPD - smoke detector.
IPR - manual fire detector.
IPT - heat fire detector.
ISB is an integrated security system.
ISB "Network A" is an integrated system of security and fire alarm and access control "Network A".
Key "GZ" - a user key used to warn the monitoring station operators about the actions taken at the security object by the service personnel (detention group), as well as allowing the removal of the "Alarm" and / or "Fire" state with the possibility of resetting the loops (zones) to the state "Protection" (subject to their normalization).
User key - a key confirming the user's right to perform certain actions with the device, as a user key when working with the “A6” device it is possible to use: keys of the contact method of reading DS1990A, DS1991-DS1996; proximity cards Proximity; digital PIN code.
Key "Fitter" - a user key used to warn the monitoring station operators about the actions taken at the security facility by the service personnel (electrician).
"Master" key - a user key that gives the right to perform arming and disarming of zones. Also, the "Master" key allows you to remove the "Alarm" state
round-the-clock loops and / or the "Fire" state of fire loops with the possibility of resetting the loops to the "Guard" state, provided that these loops are assigned to the security zone for this key and the detectors in the loop are normalized.
"MASTER" -code - user key, which gives the right to carry out operations to change the configuration of the device (programming the device).
Object communication line - a communication line used to connect devices into an integrated system.
User - a person who has the right to perform certain actions limited by the access level ("MASTER", "Master", "GZ", "Installer").
PPKOP is a fire alarm control panel.
Software - software.
CMS is a centralized surveillance console.
PC - personal electronic computer (personal computer).
RSPI - radio channel notification transmission system.
SZU - light and sound device.
SKD - access control system.
SPI - notification transmission system.
SCN is a centralized surveillance system.
Tamper - tamper switch.
TSO is a technical means of notification.
UD - access device.
AL - alarm loop.
PIN-code - personal identification number (digital code) can serve as a user key when performing operations with the device (provided that the PIN-code is programmed in the memory of this device).
Control Panel A6 Operation manual. Part II (programming with VPU-A-06 and PR-1) edition 7.03 April 2011 ATTENTION! Before starting to work with the device, determine its modification according to the label and passport.
This operation manual, part II, is intended to study the programming methodology for the control and monitoring fireman device "A6" TU RB 101162917.006-2000 (device "A6") using the remote control panel VPU-A-06 (VPU-A-16) and PR programming panel during commissioning at the facility. This document contains information necessary to ensure the fullest possible use of the technical capabilities of the device and its correct operation.
The installation and maintenance of the device must be allowed by persons with the necessary qualifications and permission to work with electrical installations.
This operating manual applies to the following versions of the "A6" device:
PPKOP A6-02 - control of two alarm loops;
PPKOP A6-04 - control of four alarm loops;
Control Panel A6-06 - control of six alarm loops.
Programming of A6 devices of different versions is identical, except for the sections in which the parameters of loops and zones are programmed. These sections for devices of various designs differ only in the number of programmable loops and zones.
In connection with the constant work to improve the device, which increases reliability and improves performance, minor changes may be made to the device design, which are not reflected in this edition of the "Operation Manual" and do not worsen the device's parameters.
1. GENERAL PROVISIONS
Devices "A6" for a given use case can be programmed in one of four ways to choose from:using a PC using the IS-232 module, or the PROG-1 module and the specialized software "Programmer AXX";
using the PR-1 programming panel and the corresponding programming tables;
by means of the VPU-A-06 LCD keypad using the IS-485 module and the corresponding programming tables;
by means of the VPU-A-16 LCD keypad using the IS-485, KSO-A module and the corresponding programming tables.
To program the devices, it is necessary to edit a number of groups of parameters highlighted in certain program pages. After editing, the changed configuration is written into the non-volatile memory of the device.
The A6 device contains the following program pages:
"GENERAL" ("PARAMETERS"): set the general properties of the device, select the automated security system and the type of radio channel;
"LOCKS": the parameters of each of the signaling loops are determined;
"ZONES": the properties of the arming / disarming zones and the correspondence of the loops to the zones are set;
"ACCESS": defines the properties of access control systems;
"ACTIVATORS": parameters of operation of external devices (buzzer, SZU, relay) are selected;
"KEYS": enter user keys ("OWNER", "GZ", "MONTER" and "MASTER").
Programming the parameters of the device using a PC is one of the most convenient and intuitive ways.
This programming option makes it possible to create an archive and store the program settings of each device in the form of files on a PC, which allows you to restore at any time the full configuration of the device on any of the objects. Also, in addition to programming devices, specialized software makes it possible to monitor devices connected to the network and view all events occurring in them.
It is recommended to use the PR-1 programming panel and ZhKI keyboard VPU-A-06 when programming the device or making changes to its program settings directly at the facility.
In the case of programming using PR-1, the parameter values are entered in a hexadecimal code into the corresponding memory cells of the console, according to the programming table, with the subsequent transfer of the entire program from the PR-1 console to the nonvolatile memory of the device. Also, the convenience of using the PR-1 programming panel lies in the possibility of storing in the PR-1 non-volatile memory of the electronic keys of the services: "GZ" and "MONTER" (keys of the contact method of reading DS1990A, DS1991-DS1996). And, if necessary, prompt transfer of the key data codes to the device memory.
When programming with VPU-A-06, the program settings of the panel are first read into the keyboard memory and after editing, in accordance with the programming tables, by writing are entered into the non-volatile memory of the device.
When combining A6 devices into the “Network A” ISB based on KSO-A, programming of the device configuration is possible using the VPU-A-16 LCD keypad. When using this programming method, the program settings of the panel using VPU-A-16 are read into the KSO-A memory and, after programming the device configuration for a given use case, they are entered into the nonvolatile memory of the device by writing.
Control Panel A6 Operation manual. Part II (programming with VPU-A-06 and PR-1) revision 7.03 April 2011 2 Description of the configuration parameters of the device "A6"
2.1 GENERAL program page
In the "GENERAL" program page, the general settings of the programmable device are set, the automated security alarm system is selected and the communication channel is determined when the device is used as part of notification transmission systems.
2.1.1 Programming the "General device settings" parameter:
"Restoring the state of the device after a power failure";
"Prohibition of exclusion of common loops during capture";
2.1.1.1 "Restoring the state of the control panel after a power failure" - when this parameter is set, the control panel saves in the non-volatile memory the current state of the armed zones (state "Armed", "Disarmed") at the moment of complete power-off (restart after programming, etc.) ) and restores the state of the armed zones (the state "Armed", "Disarmed") after the control panel power supply is restored.
EXAMPLE: If the control panel is de-energized, the zones of which were in the “Armed” state, these zones will return to the “Armed” state when the control panel power is restored.
2.1.1.2 "Prohibit exclusion of common loops when arming" - when this parameter is set, the loops that are common to several zones are switched to the "Guard" state when any of the zones including these common loops is first armed.
EXAMPLE: 2 security zones have been programmed, including common zones 03 and 04:
zone # 1 includes security loops: 01, 02, 03, 04 and is controlled by the "Master" key # 1;
zone # 2 includes security loops: 03, 04, 05 and is controlled by the "Master" key # 2;
during programming, the "Prohibit bypassing common loops when arming" mode is selected.
Upon presentation of the user key “Master” No. 2, loops 03, 04, 05 will go into the “Guard” state, while the loops 01, 02 entering zone No. 1 will remain in the disarmed state.
2.1.2 Programming the "Automated security system" parameter
"ASOS type" - this parameter determines the operating mode of the device as part of automated notification transmission systems, or in stand-alone mode.
When programming the parameter "Type ASOC" the following modes are available for selection:
"Autonomous" (ASOS "Alesya" -fon);
2.1.2.1 "Autonomous" (ASOS "Alesya" -phone) - this mode is set when the device is used in the autonomous mode of protection when displaying notifications on the control panel, sirens and / or another control panel, it is also possible to use the device as part of the ISB "Network A "And monitoring station of the" Neva "type.
ISB "Network A" is built on the basis of a processor module KSO-A with the ability to combine up to 32 devices (devices "A6", "A16-512" and up to 4 remote control panels of the VPU-A-16 series) and monitoring on a PC with installed specialized software.
The monitoring station of the "Neva" type is an automated system for transmitting notifications and is designed to provide centralized protection of telephoned objects using existing telephone lines as information channels with switching them over to the period of protection.
NOTE: In the "Standalone" operating mode, the control panel loops are programmatically divided into independent arming / disarming zones. Each of the "Master" keys is assigned the right to operate with zones. Upon presentation of the "Master" key, the device will automatically arm or disarm the corresponding zone.
2.1.2.2 "Atlas" - this mode is set when using the device as part of the monitoring station "Atlas".
The monitoring station "Atlas" is an automated system for the transmission of notifications and is intended for the implementation of centralized protection of telephonized objects using existing telephone lines as information transmission channels. In the standby mode of operation, the device generates a continuous signal with a frequency of 18 kHz to the subscriber telephone line (the device is connected to the ATL to the TEL terminals of the ISA-8 matching module via a relay), if the device registers the states "Alarm", "Fire" - the signal is sent to the subscriber line stops (the device relay breaks the ATL connection circuit).
NOTE: In the "Atlas" operating mode, the telephone line is connected through the relay contacts to the board of the ISA-8 matching module to the TELL terminals. The relay output must be assigned the "Output to Atlas" parameter.
2.1.2.3 "Alesya" - this mode is set when using the device as part of ASOS "Alesya".
Selecting the "Alesya" mode involves programming a number of parameters:
"Line code" - this parameter is required to be entered when the device operates as part of a direction switch of the KLT type, the value of the "Line code" parameter depends on the cross-connect of the ATC line, the input range is 0 ... 200.
If the line is not a code, the "Line Code" must be programmed: 0.
Control Panel A6 Operation manual. Part II (programming with VPU-A-06 and PR-1) revision 7.03 April 2011 "Start card address" - this parameter is programmed when two devices are operating on one telephone line as part of ASOS "Alesya" (1 - the first device on the line ( one device on the line); 2 - the second device on the line). By default "Start card address": 1.
"Number of cards" - this parameter determines the number of cards by which notifications will be transmitted to the monitoring station of ASOS "Alesya". When working as a part of ASOS "Alesya", the device allows transmitting to the monitoring station the state of a part of the loops used in it.
EXAMPLE: 1 - transmission of the state of 8 loops; 2 - transmission of the status of 16 loops, etc., the maximum programmable "Number of cards" is 6, according to the maximum number of loops 48).
NOTE: In the "Alesya" operating mode, all control panel loops are programmatically divided into independent arming / disarming zones. Each of the "Master" keys is assigned the right to operate with zones (arming, disarming). The zone will be set to the “Guard” state after presenting the “Master” key, it will be carried out only after confirmation of the arming operation has been received from the monitoring station ASOS “Alesya” (while waiting for the confirmation of the arming operation, the sv / diode of the reader will pulsate).
2.1.3 Programming the "Communication" parameter
"Communication channel No. 1", "Parameters of communication channel No. 1" - the operating mode of the device as a part of notification transmission systems, where additional transmission devices are connected to the device to communication channel No. 1 (slot XP1 of the A6-02 device board, slot XP4 of the boards device versions A6-04, A6-06).
When programming the properties of communication channel # 1, the following operating modes are available to select the "Type of communication channel" parameter:
"Absent";
"LIGHTHOUSE" ("STARS");
2.1.3.1 "Absent" - this mode is set when the control panel is used in the stand-alone mode of arming when displaying notifications on the control panel, sirens and / or another control panel, i.e. the communication channel is disabled.
2.1.3.2 "LIGHTHOUSE" ("STARS") - this mode is set when using the device as part of the RSPI "Mayak" ("STARS"), "RRT Laboratorija" where information is transmitted to the monitoring station using a radio channel. The choice of the "LIGHTHOUSE" ("STARS") mode presupposes the programming of the parameter:
"The number of controlled areas";
"Autotest (x 4.25 min)" - not used.
2.1.3.3 "CORTEX" - this mode is set when the device is used as part of the RSPI "IRBIS" (CORTEX). Selecting the "CORTEX" mode
"The number of controlled areas";
"Autotest (х 4.25 min.)";
"Device number".
3.1.3.4 "PIMA" - this mode is set when using the device as part of the RSPI "Andromeda". Selecting the "PIMA" mode involves programming a number of parameters:
"The number of controlled areas";
"Autotest (х 4.25 min.)";
"Device number" - restriction on parameter entry up to 8191;
"Station number" - restriction on entering the parameter from 1792 to 2047;
"Number of frames in a parcel" - restriction on the choice of the parameter: 5; 7; ten; 15;
"Number of messages for one notification" - restriction on the choice of the parameter: 3; 5; 7; nine;
"Use an extended set of notifications."
2.1.3.5 "Contact ID" - this mode is set when the device is used as part of an SPI that supports the standard Ademco Contact ID data transfer protocol. Selecting the "Contact ID" mode
involves programming a number of parameters:
"The number of controlled areas";
"Autotest (х 4.25 min.)";
"Device number";
"Phone number 1";
"Phone number 2".
Control Panel A6 Operation manual. Part II (programming with VPU-A-06 and PR-1) edition 7.03 April 2011 2.1.3.6 "4 + 2" - this mode is set when using the device as part of the SPI that supports the standard 4 + 2 data transfer protocol.
Selecting the "4 + 2" mode involves programming a number of parameters:
"The number of controlled areas";
"Autotest (х 4.25 min.)";
"Device number";
"Phone number 1";
"Phone number 2".
2.1.3.7 "LARS" - this mode is set when using the device as part of the RSPI "LARS".
Selecting the "LARS" mode involves programming a number of parameters:
"The number of controlled areas";
"Autotest (х 4.25 min.)".
2.1.3.8 "IP / GSM" - this mode is set when the device is used as a part of an SPI that supports data transmission using GSM / GPRS channels. Selecting the "IP / GSM" mode
involves programming a number of parameters:
"The number of controlled areas";
"Autotest (х 4.25 min.)".
2.1.4 When defining the type of communication channel, a number of parameters characteristic of the selected communication channel become available for editing.
2.1.4.1 "Number of monitored zones" - this parameter defines the number of zones (starting with the first) through which information will be transmitted to the monitoring station. Entering this parameter is mandatory for the selected type of communication channel.
2.1.4.2 "Autotest (x 4.25 min)", this parameter defines the interval of the periodic test, with which the device will automatically send a test message to the monitoring station of the SPI, table. The input of this parameter is carried out when it is necessary to organize the monitoring of the device operability at the facility.
NOTE: The interval of test messages is set in dimensionless units at the rate of 1 = 4.25 min. (4 min 15s), table 1.
Table 1 - Interval of test messages Programmable Time Programmable Time value of atotest value of atotest 1 4min.15s. 8 34min.
2 8min 30s 9 38min 15s
3 12min 45s 10 42min. 30s.
4 17min. 11 46min 45s
5 21min 15s 12 51min.
6 25min 30s. 13 55min 15s
7 29min 45s etc. if necessary 2.1.4.2 "Device number" - this parameter defines the unique number of the device, when working as part of a SPI. Entering this parameter is mandatory for the selected type of communication channel.
2.1.4.3 "Station number" - this parameter defines the unique number of the monitoring station (monitoring station number) when a programmable device operates as part of the Andromeda RSPI ("PIMA").
2.1.4.4 "Number of frames in a message" - this parameter determines the number of frames in one message when sending a notification to the monitoring station of the RSPI "Andromeda". Entering this parameter is mandatory for the selected type of communication channel of work ("PIMA").
2.1.4.5 "Number of messages for one message" - this parameter defines the number of messages for sending one message to the monitoring station. Entering this parameter is mandatory for the selected type of communication channel of work ("PIMA").
2.1.4.6 "Use an extended set of notifications" - this parameter determines the operating mode of the device (A6, A16-512), provided that the zones are programmed in the device, notifications by the zones of the device pass through different cards to the monitoring station of the SPI “Andromeda”, if this is not indicated mode, in this case notifications are sent only on the base card ("PIMA").
2.1.4.7 "Telephone No. 1", "Telephone No. 2" - this parameter defines the number of the first telephone and the second telephone for dialing, respectively ("Contact ID", "4 + 2").
2.2 Program page "LOOP"
In the program page "LOOP", the properties of the signaling loops of the programmable device are set.
2.2.1 When programming the parameters of a loop, the following "Types of loops" are available for selection:
"Security";
Control Panel A6 Operation manual. Part II (programming with VPU-A-06 and PR-1) edition 7.03 April 2011 "Round the clock";
"Anxious";
"Firefighter for 4 states";
"Firefighter closed";
"Open firefighter";
"Fireman smoke 2-wire";
"Control of fire extinguishing".
2.2.1.1 "Intruder" - this type of loop is intruder and is designed to monitor the state of intruder detectors.
It is allowed to include security devices with normally closed contacts and / or normally open contacts in the security loop (detector relays, instrument relays, etc.).
ATTENTION! During programming, the security loop (group of security loops) must be allocated to an independent zone in accordance with the required configuration of the device, the zone is assigned the “Master” keys, which will be used to perform operations over the security zone (arming and disarming).
Any impact on the loop (open circuit, short circuit, detector triggering) in the "Guard" state
is perceived by the device as "Alarm". Resetting the "Alarm" state of the security loop and resetting it to the "Guard" state is carried out with the "GZ" key, provided that the devices in this loop are normalized, or with the "Master" key.
NOTE: If it is necessary to separate two alarms "Alarm break" and "Alarm sensor" in the security loop, normally closed contacts in one case are switched on without a shunt resistor, and in the second case they must be shunted with a load resistor of 1.5 kOhm, the connection diagram is given in "Instruction manual. Part I "on the device A6.
The choice of the "Security" zone type assumes the possibility of programming a number of parameters:
"Loop response time";
"Entry Delay";
Exit Delay;
"Linking with the previous";
"Linking with the follow-up."
2.2.1.2 "Round the clock" - this type of loop is a security loop and is intended for round-the-clock monitoring of the status of devices connected to the loop.
It is allowed to include security devices with normally closed contacts and / or normally open contacts (detector tamper, instrument relays, etc.) in the round-the-clock loop.
The arming of a 24-hour loop is carried out automatically after turning on the power supply of the device; disarming of a 24-hour loop is impossible.
Any impact on the round-the-clock loop (open circuit, short circuit, detector triggering) is perceived by the device as "Alarm". Resetting the "Alarm" state of a 24-hour loop and resetting it to the "Guard" state is carried out with the "GZ" key if the detectors in this loop are normalized, or with the "Master" key, if the loop is assigned to the zone and the detectors in the loop are normalized.
NOTE: If it is necessary to separate two alarms "Break alarm" and "Sensor alarm" in a round-the-clock loop, normally closed contacts in one case are switched on without a shunt resistor, and in the second case they must be shunted with a load resistor of 1.5 kOhm, the connection diagram is given in "Instruction manual. Part I "on the device A6.
The choice of the loop type "Round the clock" implies the possibility of programming a number of parameters:
"Loop response time";
"Linking with the previous";
"Linking with the follow-up."
2.2.1.3 "Alarming" - this type of loop is alarming and is designed to control the state of alarm detectors.
It is allowed to include alarm detectors with normally closed contacts and normally open contacts in the "Alarm" loop (alarm buttons, manual call points, etc.).
ATTENTION! During programming, the alarm loop must be allocated into a separate independent zone in accordance with the required configuration of the control panel, the zone is assigned the “Master” keys, which will be used to perform operations on the alarm zone (arming and disarming).
Any impact on the alarm loop (open circuit, short circuit) is perceived by the device as "Silent alarm", when the device is used as part of the SPI, the message "Emergency call: Panic button" is generated.
Resetting the "Silent alarm" state of the alarm loop and resetting it to the "Guard" state
it is carried out with the "GZ" key, or with the "Master" key, provided that the detectors in this loop are normalized.
The choice of the "Alarm" loop type implies the possibility of programming a number of parameters:
"Loop response time";
Control Panel A6 Operation manual. Part II (programming with VPU-A-06 and PR-1) edition 7.03 April 2011 "Linking with the previous one";
"Linking with the follow-up."
2.2.1.4 "Firefighter for 4 states" - this type of loop is a fire one and is intended for round-the-clock monitoring of the state of fire detectors.
It is allowed to include fire detectors in the “Firefighter for 4 states” loop only with normally closed contacts (heat, manual, smoke detectors, etc.).
NOTE: Normally closed contacts of a fire detector included in the "Fire for 4 states" loop must be bridged with a load resistor of 1.5 kOhm.
Arming of the “Firefighter for 4 states” loop is carried out automatically after the control panel is powered on, disarming the “Firefighter for 4 states” loop is impossible.
For the “Firefighter for 4 states” loop type, the device distinguishes the following 4 states: “Normal”, “Fire”, “Open”, “Short circuit”.
In case of breakage and short circuit of the “Firefighter for 4 states” loop, the device generates a “Fault” notification, the “Fire” notification is generated only in the event of a detector triggering.
Resetting the “Fault” state of the loop and resetting it to the “Guard” state occurs automatically, provided that the loop is normalized. Resetting the “Fire” state of the loop and resetting it to the “Guard” state is carried out with the “GZ” key if the detectors in this loop are normalized, or with the “Master” key, if the loop is assigned to the zone and the detectors in the loop are normalized.
If necessary, for the type of loop "Firefighter for 4 states" it is possible to organize a difference of 5 states: "Norm", "Attention" (triggering of one detector), "Fire", "Open", "Short circuit". This is achieved by programming the "Verification time" parameter.
The choice of the type of loop "Firefighter for 4 states" implies the possibility of programming a number of parameters:
"Loop response time";
"Verification time";
"ADC level correction";
"Linking with the previous";
"Linking with the follow-up."
2.2.1.5 "Closed fire (response to break)" - this type of loop is a fire one and is intended for round-the-clock monitoring of the state of fire detectors.
It is allowed to include fire detectors only with normally closed contacts (thermal, manual, smoke detectors, etc.) in the “Fire closed” loop.
Arming of the “Firefighter closed” loop is carried out automatically after the device is powered on, disarming the “Firefighter closed” loop is impossible.
For the type of loop "Fire closed", the device distinguishes the following 3 states: "Norm", "Fire", "Short circuit".
In the event of a short circuit in the loop, the control panel generates a “Fault” notification, and a “Fire” notification is generated in the event of a detector triggering and / or a loop break. Resetting the “Fault” state of the “Fire closed” loop and resetting it to the “Guard” state occurs automatically, provided the loop is normalized. Resetting the “Fire” state of the loop and resetting it to the “Guard” state is carried out with the “GZ” key if the detectors in this loop are normalized, or with the “Master” key, if the loop is assigned to the zone and the detectors in the loop are normalized.
If necessary, for the type of loop "Fire closed", you can organize a difference of 4 states: "Normal", "Attention" (triggering of one detector), "Fire", "Short circuit". This is achieved by programming the "Verification time" parameter.
Resetting the "Attention" state in the loop and resetting it to the "Guard" state occurs automatically after the programmed verification time has expired.
Choosing the type of loop "Fire open", if necessary, involves programming a number of parameters:
"Loop response time";
"Verification time";
"ADC level correction";
"Linking with the previous";
"Linking with the follow-up."
2.2.1.6 "Open fire (tripping on short circuit)" - this type of loop is a fire one and is intended for round-the-clock monitoring of the state of fire detectors.
It is allowed to include fire detectors only with normally open contacts (thermal, manual, etc.) in the "Firefighter open" loop.
Arming of the "Firefighter open" loop is carried out automatically after the control panel is powered on, disarming the "Firefighter open" loop is impossible.
Control Panel A6 Operation manual. Part II (programming with VPU-A-06 and PR-1) revision 7.03 April 2011 For the type of loop "Fire open" the device distinguishes the following 3 states: "Norm", "Fire", "Break".
If the loop is broken, the device generates a "Fault" message, a "Fire" message
generated in the event of a detector actuation and / or short circuit of the loop. Resetting the “Fault” state of the “Firefighter open” loop and resetting it to the “Guard” state occurs automatically, provided the loop is normalized. Resetting the “Fire” state of the loop and resetting it to the “Guard” state is carried out with the “GZ” key if the detectors in this loop are normalized, or with the “Master” key, if the loop is assigned to the zone and the detectors in the loop are normalized.
If necessary, for the type of loop "Open fire", it is possible to organize a difference of 4 states: "Normal", "Attention" (triggering of one detector), "Fire", "Break". This is achieved by programming the "Verification time" parameter.
Resetting the "Attention" state of the loop and resetting it to the "Guard" state occurs automatically after the programmed verification time has expired.
The choice of the type of loop "Fire open" involves the programming of a number of parameters:
"Loop response time";
"Verification time";
"ADC level correction";
"Linking with the previous";
"Linking with the follow-up."
2.2.1.7 "Firefighter smoke 2-wire" - this type of loop is a fire one and is intended for round-the-clock monitoring of the state of fire detectors.
It is allowed to include fire detectors (smoke two-wire current-consuming detectors, heat detectors with normally open contacts, manual detectors with normally open contacts, etc.) in the "Firefighter smoke" loop.
NOTE: The "Smoke fire" loop must be connected to the control board through the contacts of the relay programmed as "Reset relay".
Arming of the "Firefighter smoke" loop is carried out automatically after turning on the power supply of the device, disarming the "Firefighter smoke" loop is impossible.
For the type of loop "Fire smoke 2-wire", the device distinguishes the following 4 states:
"Norm", "Fire", "Break", "Short circuit".
In the event of a break or short circuit in the loop, the device generates a “Fault” notification, a “Fire” notification is generated only if the detector is triggered. Resetting the “Fault” state of the loop and resetting it to the “Guard” state occurs automatically, provided that the loop is normalized. Resetting the "Fire" state of the loop and resetting it to the "Guard" state
it is carried out with the "GZ" key if the detectors in this loop are normalized, or with the "Master" key, if the loop is assigned to the zone and the detectors in the loop are normalized.
ATTENTION! Normalization of detectors (transition to standby mode) in the "Smoke fire" loop
carried out by means of a reset relay (the maximum waiting time for the normalization of the detectors is not more than 4 min. 15 s. - non-programmable loop reset period).
If necessary, for the type of loop "Firefighter smoke 2-wire" it is possible to organize a difference of 5 states: "Norm", "Attention" (triggering of one detector), "Fire", "Break", "Short circuit". This is achieved by programming the "Verification time" parameter.
Resetting the "Attention" state in the loop and resetting it to the "Guard" state occurs automatically after the programmed verification time has expired.
The choice of the type of zone "Smoke fire" involves programming a number of parameters:
"Loop response time";
"Verification time";
"ADC level correction";
"Linking with the previous";
"Linking with the follow-up."
2.2.1.8 "Control of fire extinguishing" - this type of loop is a technological one and is intended for round-the-clock monitoring of the state of technical means of warning in accordance with the classification of warning systems SO-1 and CO-2.
It is allowed to include the following TCO in the “Fire control” loop: light, light and sound, light-speech devices, etc.
NOTE: The “Fire extinguishing control” loop must be connected to the control board through the relay contacts (the relay is programmed according to the “Alarm” event level in accordance with the required configuration).
The state of the “Fire extinguishing control” loop is monitored automatically after the device is powered on, disarming the “Fire extinguishing control” loop is impossible.
For the type of loop "Control of fire extinguishing", the device distinguishes the following 3 states: "Norm", "Open", "Short circuit".
Control Panel A6 Operation manual. Part II (programming with VPU-A-06 and PR-1) revision 7.03 April 2011 In case of open circuit and short circuit of the loop, the control panel generates a "Fault" notification. Resetting the “Fault” state of the loop and resetting it to the “Guard” state occurs automatically, provided that the loop is normalized.
The choice of the type of loop "Control of fire extinguishing" involves the programming of a number of parameters:
"Loop response time";
"No. of the executive relay";
"Linking with the previous";
"Linking with the follow-up."
2.2.2 When you select a certain "Type of loop", a number of parameters that are specific to the selected type of loop become available:
2.2.2.1 "Loop response time (s)" This parameter defines the time period during which the effect (open circuit, short circuit, load) must remain in the loop so that the device can record it.
The longer the response time is, the more immune the loop is to interference.
The parameter "Loop response time (s)" is selected from the proposed range of values:
2.2.2.2 "Entry delay (s)", this parameter defines the time period after which the zone will be disarmed, the countdown starts after the "Master" key is presented
(set in seconds).
The "Entry delay (s)" parameter is set when the electronic key reader is located inside the protected area.
3.2.2.3 "Exit delay (s)", this parameter defines the time period after which the loop will switch to the "Guard" state, the countdown starts after the "Master" key is presented
(set in seconds).
NOTE: When arming, the loop with the Exit Delay parameter must be normalized.
2.2.2.4 "Linking with the previous", "Linking with the next" These parameters determine the dependence of the activation of actuators on the state of the associated loops.
It is recommended to use loops with preset connection parameters in systems with automatic fire control systems. The device allows organizing the triggering of output devices in case of alarm in two adjacent connected loops. If at least one of the group of connected loops is not in the "Alarm" state, the "Activator" will not start external devices. The indication of the "Alarm" state in the loop does not differ from the indication of ordinary loops.
ATTENTION! A prerequisite for organizing linked loops is the obligatory programming of the "Activator" with the "Linkage alarm" alarm level.
EXAMPLE: Setting the “Link with previous” parameter for loop # 5 means that loop # 5 is connected to loop # 4. Setting the “Link with subsequent” parameter for the loop # 4 means that the loop # 4 is connected with the loop # 5.
2.2.2.5 "Verification time (s)", this parameter defines the time period during which the control panel expects confirmation of the "Fire" state in this loop (repeated triggering of the detector in the loop).
When a fire detector in a loop is triggered, the device, using the "Reset Relay", makes a 4-second power reset in this loop, thereby normalizing the triggered detector to standby mode. After normalization of the detector, the countdown of the programmed verification time begins, if before the verification time expires, any detector in this loop is triggered, the control panel will register the "Fire" state.
ATTENTION! When programming the "Verification time" parameter, a prerequisite is programming the "Reset relay" parameter for the relay and the corresponding connection of the loop through the relay contacts.
2.2.2.6 "ADC level correction" - changing this parameter allows you to adjust the "Fire" signal output threshold when using some types of two-wire smoke detectors.
The need to correct this parameter may arise at the stage of commissioning, when the device incorrectly generates the "Attention" and "Fire" signals. In this situation, it is necessary to programmatically change the ADC level.
The ADC levels corresponding to the loop states are shown in Table 8.
The entered number is selected experimentally from the range from 1 to 255. If it is necessary to increase the "Fire" notification threshold, a number from 1 to 127 is entered (as a rule, the number is selected from the range of 10, 20, 30, etc.), and when the notification threshold is decreased Fire is a number from 128 to 255 (selected from 250, 240, etc.).
Control Panel A6 Operation manual. Part II (programming with VPU-A-06 and PR-1) edition 7.03 April 2011
EXAMPLE: The following parameters are programmed:
two-wire smoke loop;
loop verification time 255;
reset relay.
When the first detector is triggered, the power supply of the loop must be reset using the reset relay and the device must register the "Attention" state for this loop (ie the ADC level when one detector is triggered must be within the range from 60 to 119).
The control panel will register the "Fire" state for a given loop when two detectors in the loop are triggered during the verification time (ie the ADC level when two detectors are triggered should be within the range from 83 to 236).
If, when one detector is triggered, the device immediately registers the "Fire" state, then it is necessary to reduce the "Fire" notification threshold by experimentally choosing a value from 128 to 255 (recommended 220).
Table 2 - ADC levels of loop states Loop state ADC level Break 001 - 024 Norm 025 - 059 Attention (activation of the 1st detector) 060 - 119 Fire (activation of 2 detectors) 083 - 236 Short circuit 237 - 255 During commissioning work on object for the device "A6", the ADC level of each loop can be monitored using specialized software, which is provided on condition of contacting the company's service center.
2.2.2.7 "No. of the executive relay" - this parameter defines the number of the executive relay for the type of loop "Control of fire extinguishing" with enabled TCO. Through the programmed executive relay, power is supplied to the TCO when an alarm condition is registered.
The number of the executive relay to be entered is selected from a range from 1 to 25 in accordance with the connection of the “Fire extinguishing control” loop.
2.3 Program page "ZONE"
In the program page "ZONE", alarm loops are combined into independent security zones.
When programming security zones
"Loops entering the zone";
"Delay of confirmation of withdrawal";
"Indication on the access device No. 2".
2.3.1 "Loops included in the zone" - select the loops for this security zone. Combining loops into the security zone makes it possible by presenting the appropriate "Master" key
carry out the following operations:
arming a zone;
disarming a zone;
reinstallation of fire loops entering the security zone from the "Fire" state to the "Guard" state;
resetting round-the-clock loops entering the armed zone from the "Alarm" state to the "Guard" state.
ATTENTION! Combining alarm loops into zones is mandatory for the types of loops "Guard" and "Alarm", and recommended for the types of loops "Round-the-clock", "Firefighter for 4 states", "Firefighter closed", "Firefighter open", "Firefighter smoke 2 wired "and" Fire control ".
There are several options for assigning loops to zones:
one alarm loop refers to one zone;
an arbitrary number of alarm loops refer to one zone;
the alarm loop can be assigned simultaneously to several zones (the loop is common to the armed zones).
If the loop is common for the armed zones, then arming and disarming the common loop will be carried out depending on the state of these armed zones:
the common loop will not be armed if any one of the zones to which it is assigned is not armed;
the common loop will only be armed when the last of the zones to which it is assigned is armed;
the common loop is disarmed only when any of the zones to which it is assigned is disarmed.
Control Panel A6 Operation manual. Part II (programming with VPU-A-06 and PR-1) revision 7.03 April 2011 2.3.2 "Disarming confirmation delay (s)" - the parameter is assigned to zones if it is necessary to control the authorized disarming of these zones using the "Master" keys. This parameter, in most cases, is programmed when using the device as part of the monitoring station.
Programming the “Disarming confirmation delay” time for a certain zone obliges the user who presented the “Master” key to confirm the disarming within the programmed time by pressing the “Disarming confirmation button”, otherwise the monitoring station will receive the “Emergency call” alarm. Removal under duress. "
ATTENTION! Contacts of the "Removal confirmation buttons" should be normally closed and bridged with a resistance of 1.5 kOhm. When installed, the "Removal confirmation button" is located in a hidden place in the room, the location of the button should be known only to the owner.
2.3.3 "Indication on access device No. 2" - the parameter is assigned when it is necessary to indicate the status of zones on the LED / LED of the reader connected to the TP2 reading channel. (for A6 device, versions A6-04, A6-06)
2.4 "ACCESS CONTROL" program page
In the program page "ACCESS CONTROL" the parameters of the "Access Subsystems" of the device are set, for the A6 device, versions A6-04, A6-06.
The maximum number of "Access Subsystems" created in the "A6" device:
versions А6-02 - 1;
executions А6-04, А6-06 - 2.
When creating access subsystems, the following parameters are available for editing:
"Zones included in the access subsystem";
"Loops with an installed SKD button";
"Arming delay (s)";
"Exit button";
"Passage by any key, if the zone is not armed."
2.4.1 "Zones included in the access subsystem" - indicate the zones related to this access subsystem. Programming of this parameter is mandatory if it is necessary to organize control of the armed zone (arming and disarming).
2.4.2 "Loop with an installed SKD button" - indicates the loop of the device, which includes the "Exit button" (if available) and "Arming button".
2.4.3 "Arming delay (s)" - this parameter defines the period of time during which it is necessary to present the "Master" user key to arm the zone. The countdown of the “Arming delay” time starts after pressing the “Arming button”.
ATTENTION! The “button for arming” must be with normally closed contacts shunted by a 3kOhm resistor, the terminal resistor of the pushbutton loop is 1.5kOhm.
2.4.4 "Exit button" - this parameter indicates that there is a button in the "Access subsystem" of the device, pressing of which leads to the opening of the door lock for exiting. The “Exit button” is installed indoors and is included in the loop specified in the “Loop with the ACS button installed” parameter.
ATTENTION! The “exit button” should be with normally closed contacts, shunted by a 1.5 kOhm resistor, the end-of-line resistor of the push-button loop is 1.5 kOhm.
2.4.5 "Access by any key, if the zone is not armed" - this parameter indicates that any presented electronic key will trigger the opening of the lock, regardless of whether this key is registered in the control panel's memory or not.
2.5 "ACTIVATORS" program page
In the program page "Activators", programs (scenarios) for the operation of executive devices (buzzer, TCO outputs, relay outputs) are created in accordance with the logic of work at the facility.
The maximum number of independent programs "Activator", with different logic of work - 8.
When creating the Activator program, the following general parameters are available for editing:
"Event level" ("Alarm level");
"Type of reaction";
"Delay of operation";
"Duration of response";
"Track the security mode";
"Sources of activation";
"Disabling the activator";
"Loops";
"Subsystems of access".
2.5.1 The “Event level” parameter specifies the event level at which the “Activator” must launch the executive devices.
2.5.1.1 "Alarm" - the activation of executive devices by the "Activator" will be carried out when the device registers alarm events, provided that they are programmed for this "Activator".
The following events can be assigned to the "Alarm" event level:
"Alarm" in the loop;
Control Panel A6 Operation manual. Part II (programming with VPU-A-06 and PR-1) edition 7.03 April 2011 "Fire" in the loop;
"Device tamper";
"Key selection";
"Compulsion".
2.5.1.2 "Linkage alarm" - the triggering of executive devices by the "Activator" will be carried out when the control panel registers alarm events simultaneously in two linked loops, provided they are programmed for this "Activator".
2.5.1.3 "Fault" - the activation of executive devices by the "Activator" will be carried out when the device registers faults, provided that they are programmed for this "Activator".
The following events can be assigned to the "Fault" event level:
"Fault" in the loop;
"Alarm" in the loop;
"Fire" in the loop;
"Device tamper";
"Lack of 220 V network";
"Lack of battery";
"Communication channel failure";
Siren malfunction.
2.5.1.4 "Warning" - the activation of executive devices by the "Activator" will be carried out when an event is being checked for the fact that the event has been assigned the "Alarm" state, provided that it is programmed for this "Activator".
The following events can be assigned to the "Warning" event level:
"Attention" for the fire loop;
countdown of the "Entry delay" time for the security loop;
countdown of the "Exit delay" time for the security loop.
2.5.1.5 "Multiple alarm" - the activation of executive devices by the "Activator" will be carried out every time the device registers an alarm state, regardless of the fact that this alarm state has already been registered, provided that it is programmed for this "Activator".
The following events can be assigned to the "Multiple alarm" event level:
"Alarm" in the loop;
"Fire" in the loop;
"Device tamper".
2.5.1.6 "Fault at the monitoring station" - the activation of executive devices by the "Activator" will be carried out when the device registers faults, provided that they are programmed for this "Activator".
The following events can be assigned to the event level "Fault at monitoring station":
"Fault" in the loop;
"Device tamper";
"Lack of 220 V network";
"Lack of battery";
"Communication channel failure";
Siren malfunction.
2.5.2 The "Reaction type" parameter determines the reaction of the executive devices when events are registered by the control panel.
2.5.2.1 "Continuous" - "Activator" with this type of reaction after starting will work in continuous mode for the programmed time.
2.5.2.2 "Pulsating" - "Activator" with this type of reaction after starting will operate in a pulsating mode: it will be switched on for 1 second with a period of 2 seconds during the programmed time.
EXAMPLE: The "Pulsating" reaction type can be used to output a sound signal to the buzzer and / or TCO outputs when using the device in fire alarm systems.
2.5.2.3 "Fault" - "Activator" with this type of reaction after starting will work according to the following algorithm: issue a series of short impulses for 10 seconds with a period of 4 minutes for the programmed time.
EXAMPLE: The type of reaction "Fault" can be used to output a sound signal to the buzzer about system faults "Lack of battery", "Lack of 220 V", etc.
ATTENTION! When choosing the reaction type "Fault", the parameter "Response duration"
must be programmed in minutes, at least 5 minutes.
2.5.2.4 "Warning" - "Activator" with this type of reaction after starting will work according to the following algorithm: turn on for 1 second with a period of 4 seconds during the programmed time.
EXAMPLE: The reaction type "Warning" can be used to output a sound signal to the buzzer about faults in loops, etc.
Control Panel A6 Operation manual. Part II (programming with VPU-A-06 and PR-1) revision 7.03 April 2011 2.5.3 “Actuation delay” - this parameter determines the time period after which the “Activator” will start the actuators (set in seconds from 0 to 255).
EXAMPLE: The parameter “Response delay” can be used to provide the required delay when the fire automatic devices, etc. are triggered.
2.5.4 "Activation duration" - this parameter defines the time period of the "Activator" operation (set from 0 to 255).
By default, the time period is specified in seconds, if necessary, the “Response duration” parameter can be set in minutes, for which the “Response duration is specified in minutes” property must be specified.
ATTENTION! When the value of the parameter "Response duration" is set to 0, "Activator"
will work indefinitely or until reset, provided that the "Activator deactivation" parameters are programmed (reset with the L key or reset with the button).
2.5.5 "Monitor arming mode" - this parameter is used to start the "Activator" when arming the activating zones and disabling the "Activator" when disarming the activating zones.
ATTENTION! When programming the "Monitor arming mode" parameter for this "Activator"
loops must be programmed, which must be monitored.
2.5.6 "Sources of activation" defines the parameters by which the "Activator" must turn on the executive devices.
2.5.6.1 “Duress” - when this parameter is selected, the “Activator” turns on the executive devices, if the control panel registers the disarming of duress zones (the “Disarming confirmation button” is not pressed during the programmed “Disarming confirmation delay” time).
2.5.6.2 "Communication channel failure" - when this parameter is selected, the "Activator" turns on executive devices, if the device registers a loss of communication with additional modules and devices:
remote control panel VPU-A-16;
display module VPU-A-16S;
expansion module AR-16;
AMC-8 access device module;
lack of communication with ASOS "Alesya";
IS-RF matching module (loss of communication with a radio transmitter);
IS-CMS coordination module (loss of communication with the transmitter-communicator);
IS-AD matching module (loss of communication with the transmitter-communicator);
IS-GSM matching module (loss of communication with the GSM adapter, GSM / GPRS communication channel).
2.5.6.3 "Siren malfunction" - when this parameter is selected, the "Activator" turns on the executive devices, if the control panel registers a malfunction of the communication line of the BELL warning equipment.
ATTENTION! The TCO communication lines (BELL1 and BELL2) are monitored for open and short circuits using a 1.5 kΩ end-of-line resistor.
2.5.6.4 "Control panel tamper" - when this parameter is selected, the "Activator" turns on the executive devices, if the control panel registers the opening of the case and / or violation of the tamper loop, as well as when registering the opening of the enclosures and / or violation of the tamper lines of additional modules ( VPU-A-16, VPU-A-16S, AR-16, AMS-8).
ATTENTION! The tamper lines of the control panel and additional modules are monitored for open circuit and short circuit using a 1.5 kOhm end-of-line resistor.
2.5.6.5 "Key selection" - when this parameter is selected, the "Activator" turns on the executive devices, if the device registers the presentation of a key not written in the device memory 5 times in a row.
2.5.6.6 "Lack of 220V network" - when this parameter is selected, the "Activator" turns on the executive devices, if the device registers the absence of mains power (220V).
2.5.6.7 "Battery discharge" - when this parameter is selected, the "Activator" turns on the executive devices, if the device registers a discharge of the backup power source (storage battery).
2.5.7 "Disabling the activator" defines the parameters, when exposed to which the "Activator" turns off the executive devices.
2.5.7.1 "Reset with a key" - when this parameter is selected, the "Activator" will disable the impact on the actuators upon presentation of the "GZ" key (reset of the TCO sound and / or buzzer, etc.).
2.5.7.2 "Reset by button" - when this parameter is selected, the "Activator" will disable the effects on the actuators when the "Reset button" connected to the control board to the KEY and "common" terminals is pressed (reset the sound of the TCO and / or buzzer, cancel the operation fire automation systems, etc.).
ATTENTION! The button for performing the "Reset by button" function must be with normally closed contacts, shunted by a 3kOhm resistor, the terminal resistor of the pushbutton loop is 1.5kOhm.
2.5.7.3 "No reset" - when this parameter is selected, the "Activator" will run the programmed "Response duration" time regardless of external influences on the device ("Reset with a key", "Reset with a button").
Control Panel A6 Operation manual. Part II (programming with VPU-A-06 and PR-1) edition 7.03 April 2011 ATTENTION! The parameter "No reset" must be programmed when using the "Activator"
responsible for managing the "Access Subsystems".
2.5.8 "Loops" - activating loops are introduced, according to the state change of which by the "Activator"
launch is in progress.
2.5.9 "Access Subsystems" - enter a mask of activating access subsystems, when used, the "Activator" is launched.
2.6 Program page "Actuators"
For the device to perform notification functions, turn on / off fire extinguishing systems, etc., the following executive devices can be used constructively:
2.6.1 "Buzzer". The buzzer executive device on the control boards of the “A6” device is intended for sound notification of personnel about an event.
The following parameters are available for editing:
"Effective activators";
2.6.1.1 "Acting activators" - are assigned activators, when triggered, the executive device "Buzzer" should turn on.
2.6.1.2 “Indication of the last second of exit” - this parameter is assigned to the “Buzzer” when it is necessary to notify the personnel about the last second of the exit, in cases when the “Exit Delay” parameter is programmed for the security zones. The "Buzzer" is activated at the end of the "Exit Delay" time for 1 second;
2.6.1.3 "Output to the keypad service LED" - this parameter is assigned to the "Buzzer"
if it is necessary to duplicate the notification signal by the service LED of the device (programmable LED).
2.6.2 "Siren". The output of the BELL actuator on the control board of the “A6” device is designed to connect the TCO and provide sound, light and light and sound notification of personnel about the event.
The following parameters are available for editing:
"Effective activators";
"Indication of the last second of the exit";
"Normally powered";
"Output to service LED".
2.6.2.1 "Acting activators" - activators are assigned, when triggered, a 12V potential is applied to the "Siren" output.
2.6.2.2 "Indication of the last second of the output" - this parameter is assigned to the "Siren" output
if it is necessary to notify the personnel about the last second of the exit, in cases when the “Exit Delay” parameter is programmed for the security zones. The “Siren” output turns on when the “Exit Delay” time expires for 1 second;
2.6.3.3 "Normally powered" - this parameter is assigned to the "Siren" output in cases when it is necessary to provide + 12V potential at the BELL output when the device is powered.
2.6.2.4 "Output to service LED" - this parameter is assigned to the "Siren" output if it is necessary to duplicate the notification signal to the service one.
2.6.3 "Relay". The outputs of the relay actuators on the control board of the “A6” device (versions A6-04, A6-06) and the relay outputs on the PM-64 module are designed to connect alarm loops, fire automation devices, TCO, etc.
The following parameters are available for editing:
"Effective activators";
"Indication of the last second of the exit";
"Normally powered";
"Reset relay";
"Output to service LED".
"Conclusion to the Atlas".
2.6.3.1 "Acting activators" - activators are assigned, when triggered, the output "Relay"
should turn on.
2.6.3.2 "Indication of the last second of the output" - this parameter is assigned to the "Relay" outputs
if it is necessary to notify the personnel about the last second of the exit, in cases when the “Exit Delay” parameter is programmed for the security zones. The “Relay” output turns on after the “Exit Delay” time expires for 1 second;
2.6.3.3 "Normally energized" - this parameter is assigned to the "Relay" outputs in cases when it is necessary to provide normally closed relay contacts when the device is powered.
Control Panel A6 Operation manual. Part II (programming with VPU-A-06 and PR-1) revision 7.03 April 2011 2.6.3.4 "Reset relay" - this parameter is assigned to the "Relay" outputs in cases where the outputs are intended to be used for verification and power supply reset of current-consuming detectors;
ATTENTION! If the “Relay” output is assigned the “Reset relay” parameter, then the “Affecting activators” relay cannot be programmed for this output. Programming the parameter "Reset relay"
mandatory, if there are two-wire smoke loops in the system.
2.6.3.5 "Output to service LED" - this parameter is assigned to the "Relay" outputs if it is necessary to duplicate the signal by the service LED of the device.
2.6.3.6 "Output to Atlas" - this parameter is assigned to the "Relay" outputs in cases when it is necessary to transfer information to the "Atlas" monitoring station. The relay output is used in conjunction with the telephone line connection output (when using the ISA-8 matching module). The relay with the parameter "Output to" Atlas "switches 18 kHz to the telephone line monitored by the monitoring station" Atlas "
(when the control panel zone is armed, 18 kHz is fed into the telephone line and disconnected when disarmed or when there is an alarm).
ATTENTION! It is impossible to program “Affecting activators” for the “Relay” outputs if the “Output to“ Atlas ”parameter is assigned to this output.
2.7 User keys User keys are keys that confirm the user's right to perform certain actions with the device.
In software, by levels of differentiation of user access rights, the device supports work with the following types of keys:
Keys "Master";
keys "ГЗ";
Keys "Mounter";
key "Master".
It is possible to use as user keys in the device:
contact reading keys (DS1990A, DS1991-DS1996);
proximity cards Proximity (HID, EM-MARIN, Angstrem);
digital PIN code.
There are several ways to program the key ID number:
entering the electronic code when programming the device using the "Programmer AXX" software, in this case, the programmable key is presented to the reader connected to the control board of the device.
manual input when programming the device using the VPU-A-06 keyboard, this method is used to enter PIN codes;
entering the electronic code when programming the device using the VPU-A-06 keyboard, in this case, the programmed key is presented to the reader connected to the VPU-A-06 keyboard.
ATTENTION! When programming the PIN code, the first digit of the key must be different from 0 (zero), the number of characters for entering the PIN code is from 1 to 7.
2.7.1 Keys "Master"
This program page contains the user keys that give the right to carry out operations on the security zones of the device, provided that the security zones are assigned to this key "Master"
(arming, disarming).
The "Master" key also allows you to:
The maximum number of independent Master keys is 79.
When programming the "Master" keys, the following parameters are available for editing:
Key ID-number;
"Protection zone for UD-1";
"Protection zone for UD-2";
"Permitted passage through the access subsystem No. 1";
"The passage through the access subsystem No. 2 is allowed."
"Key ID-number" - an alphanumeric code of an electronic key or a digital PIN-code.
"Guard zones for UD-1", "Guard zones for UD-2" - enter security zones that can be controlled by presenting the "Master" key to the corresponding access device.
“Passage through access subsystem No. 2 is allowed”, “Passage through access subsystem No. 2 is allowed” - the access subsystems to which the entered “Master” key belongs are determined. The key can be assigned to two access subsystems at the same time and, accordingly, control both one access subsystem and two.
NOTE: If the “Security zones” and “Access Subsystems” are specified for the “Master” key, the key controls arming / disarming of the corresponding zone and allows passage through the Control Panel A6 Operation Manual subsystem. Part II (programming with VPU-A-06 and PR-1) edition 7.03 April 2011 accessed. If only the access subsystem is assigned to the key, it will be able to allow passage if the zone is not armed. Thus, it is possible to differentiate the powers of users.
2.7.2 Keys "GZ"
Keys "GZ" (Detention Groups, Rapid Response Groups, etc.). In this program page, user keys are registered, which give the right to remove the "Alarm" and / or "Fire" state with the possibility of resetting the loops to the "Guard" state, subject to their normalization.
The key "GZ" also allows you to:
viewing the events of the "Event log";
viewing the time and date of the built-in clock.
The maximum number of GZ keys is 15.
Provided that the parameter "Reset by key" is programmed for the "Activators", upon presentation of the "GZ" key, the "Activator" will disable the effects on the actuators.
If the device is used as part of the monitoring station, the presentation of the "GZ" key warns the monitoring station operators on duty about the actions being taken at the security object (arrival of the arrest group, etc.).
2.7.3 Keys "Fitter"
In this program page, user keys are registered that do not have any rights in relation to the device, but allow you to:
viewing the events of the "Event log";
viewing the time and date of the built-in clock.
The maximum number of "Mounter" keys is 15.
The user key "Installer" is used to warn the monitoring station operators about the actions taken at the security object by the service personnel (electrician).
2.7.4 Key "Master"
In this program page, a single user key is registered with access rights that allow you to:
viewing the events of the "Event log";
viewing and setting the time and date of the built-in clock;
device programming;
viewing the ADC level;
changing the contrast of the LCD keypad;
viewing the device ID-number;
viewing the firmware version of the central processor of the device and the date of creation of the firmware file.
ATTENTION! If the changed “Master” code is lost, the device will require a complete reset of the device configuration memory, which will allow restoring the factory “Master” code (factory “MASTER” code: 1).
3 DESCRIPTION OF PROGRAMMING USING THE KEYBOARD VPU-A-06
3.1 General requirements To be able to carry out work on programming (editing) configurations of devices "A6" using the remote control panel VPU-A-06, you must have:
Programmable device "A6";
Remote control panel VPU-A-06 (LCD keypad VPU-A-06).
IS-485 interface module, for connecting LCD keypad to the “A6” device.
Programming tables for VPU-A-06.
3.2 Description of the remote control panel VPU-A-06 3.2.1 Purpose of the remote control panel VPU-A-06 The remote control panel VPU-A-06 (LCD keyboard VPU-A-06) is designed to work as part of the "A6" instrument system and serves to monitor the state of security, fire and alarm loops of the alarm system (AL). With the help of the VPU-A-06 LCD keypad, the loops (zones) are armed / disarmed by selecting the panel number in the A6 instrument system and dialing an individual PIN-code for arming / disarming, clearing alarms, programming the instrument configuration; sound notification in the presence of system alarms and malfunctions.
Connecting the LCD keypad VPU-A-06 allows you to control up to 8 devices connected through the IS-485 interface modules into a single network via the RS485 communication line.
The external view of the LCD keypad VPU-A-06 is shown in Figure 1.
3.2.1.1 Functional purpose of the keys on the LCD keypad VPU-A-06.
The numeric keys "0" ... "9" are used to enter data.
"FORWARD" - move forward through the pages of the program, move forward within the page, move forward through the "Menu" modes.
"BACK" - moving backward through the pages of the program, moving backward within the page, moving backward through the "Menu" modes.
Control Panel A6 Operation manual. Part II (programming with VPU-A-06 and PR-1) revision 7.03 April 2011 "ENTER" - entry into the current "Menu" mode, entry into the address page (cell) of the program, confirmation of entering the user's PIN-code.
"CANCEL" - exit to the upper level in program points (for example, from cell to page).
"#" - selection of a zone to be displayed on the screen.
In addition, in the "Program" section for entering data in a hexadecimal code, some keys correspond to the letter values printed on the keyboard case:
"FORWARD" - "B";
"BACK" - "S";
"ENTER" - "D";
"CANCEL" - "A";
"#" - "E";
"*" - "F".
Pressing any key on the keyboard is accompanied by the backlighting of the LCD display and keys, as well as a short buzzer signal.
Figure 1 - External view of the remote control panel VPU-A-06 (VPU-A-16) 3.2.1.2 Display modes of the status LEDs of the device "A6" on VPU-A-06 are shown in Table 3.
- & nbsp– & nbsp–
NOTE: if there is a fault in the device, the keypad buzzer will sound 10 short beeps every 4 minutes.
3.2.1.3 Operation of the buzzer and siren of the LCD keypad VPU-A-06.
The keypad buzzer cannot be programmed for different operating modes, but has a rigid algorithm:
short signals (once every 4 seconds) - an event has occurred in the device (devices);
constant buzzer signal - an alarm event has occurred in the device (s).
Control Panel A6 Operation manual. Part II (programming with VPU-A-06 and PR-1) edition 7.03 April 2011 The siren output of the LCD keypad is also not programmable, and will be activated only by alarm events in the control panel (s).
3.2.1.4 Purpose of jumpers of the LCD keypad VPU-A-06:
JP1 - connection of terminal, terminating resistors to the RS485 bus;
JP3 - enable / disable the buzzer;
JP4 (1) - clearing the keyboard memory;
JP4 (2,3) - not used;
JP4 (4) - enable / disable keypad tamper;
JP5 - enable / disable permanent keyboard backlighting.
The external view of the VPU-A-06 LCD keypad with the rear cover removed is shown in Figure 2.
Figure 2 - External view of the VPU-A-06 keyboard with the rear cover removed
3.3 Connecting VPU-A-06 to the device and preparing for programming 3.3.1 Connect the IS-485 interface module to the VPU-A-06 LCD keypad in accordance with their wiring diagrams by connecting wires (wire A of the IS-485 module is connected to terminal A LCD keypad VPU-A-06, and, accordingly, wire B of the IS-485 module to terminal B of the LCD keypad VPU-A-06), Figure 21.
If several A6 devices need to be connected to the VPU-A-06 LCD keypad, then wires A and B wires of each IS-485 module are combined accordingly and connected to terminals A and B of the VPU-A-06 keypad.
3.3.2 Connect the XS1 connector of the IS-485 module to the XP1 connector of the “A6” control board.
3.3.3 Supply power to the LCD keypad VPU-A-06 and the “A6” device. The LCD keypad VPU-A-06 can be powered directly from the “A6” device or a separate 12 V UPS.
3.3.4 In case of editing the configuration of a previously programmed device, you can start working on making changes (additions) to the configuration memory microcircuit.
3.3.5 In case of programming the configuration of a new device, it is recommended to reset the memory microcircuit; for this, set the JP4 jumper on the control board of the device, and press the “Device restart” button. Wait until the device passes the test and remove the jumper.
3.3.6 After zeroing the configuration memory chip, the new device is ready for programming.
3.4 Programming the configuration of the VPU-A-06 device using VPU-A-06 3.4.1 Menu of the VPU-A-06 LCD keypad , the display will show the inscription "SYSTEM A6", Figure 3.
Figure 3 Control Panel A6 Operation manual. Part II (programming with VPU-A-06 and PR-1) edition 7.03 April 2011 3.4.1.1 Zone allocation in the system when combining A6 devices using VPU-A-06.
To carry out arming / disarming operations, viewing the event log, current time, programming using the VPU-A-06 LCD keypad, the user must perform a number of actions, including the selection of system zones.
LCD keypad VPU-A-06 allows to combine up to 8 “A6” devices into a system. In the maximum configuration, it is possible to organize up to 48 independent zones in the system (8 A6-06 devices with 6 loops in each zone, respectively), the numbers of zones and loops in the system are consecutively numbered, the numbering of zones in the system depends on the specific configuration of each device in the system.
EXAMPLE: The system consists of 4 devices united by means of the VPU-A-06 LCD keypad, independent zones in the devices and the system are distributed as follows, Figure 4.
NOTE: * In brackets are the zone numbers for each specific device.
- & nbsp– & nbsp–
As can be seen from Figure 4, zone No. 6 in the system refers to A6-06 device No. 2, however, for this device it is zone No. 3, similarly, zone No. 11 in the system refers to A6-06 No. 3 device, however, for this the appliance is zone 4, and so on.
ATTENTION! When selecting zones in the system for arming / disarming, programming, viewing the event log, it is necessary to clearly understand their distribution by devices in the system.
3.4.1.2 The keyboard menu includes a number of modes:
The "Overview" mode allows you to view the current state of loops, zones, alarms and faults in the system by pressing the "FORWARD", "BACK" keys and includes the items:
- "Zone status" - displays the status of the system zones, Figure 5;
- & nbsp– & nbsp–
Control Panel A6 Operation manual.
Part II (programming with VPU-A-06 and PR-1) revision 7.03 April 2011 The "System" mode allows you to enter the ID-numbers of devices, change the "MASTER" -code is available after performing a number of actions:
enter the “MASTER” -code of the LCD keypad: 1234 (factory “MASTER” -code of the LCD keypad);
enter the service menu by pressing key 3 - Service, Figure 8.
Figure 8
The "System" mode includes the following items:
“Device” - is intended for registration of ID-numbers of “A6” devices in the memory of the LCD keypad VPU-A-06;
"Password" - contains the "MASTER" -code of the LCD keypad VPU-A-06 (if necessary, it can be changed);
"Contrast" - displays the LCD contrast level and indication of the keypad ID-number.
The block diagram of the operation of the VPU-A-06 LCD keypad in the "System" mode is shown in Figure 9.
Figure 9 - Block diagram of the operation of the VPU-A-06 LCD keypad in the "System" mode
The Arming / Disarming mode for A6 devices is available after performing a number of actions:
using the keys "0", "1" ... "9" select a zone in the system (for example, 1, ie, selection of the 1st zone in the system), the selection of the zone for the device "A6" is carried out according to the principle described in p. .p.3.4.1.1;
confirm the zone selection with the "#" key, Figure 10;
present the key "OWNER" related to this zone.
Then you need to select, Figure 8:
1 - Arming - pressing the 1 key selects the arming operation;
2 - Disarm - pressing key 2 selects the disarming operation.
The "Event log" mode allows you to view the event log for all devices in the system, and is available after performing a number of actions:
Using the keys "0", "1" ... "9" select a zone in the system (for example, 12, ie selection of the 12th zone in the system), the selection of a zone for the "A6" device is carried out according to the principle described in p. .p.3.4.1.1;
Present the key "OWNER" related to the given zone;
enter the "Event log" mode by pressing the "ENTER" key, Figure 11.
Figure 11
In the "Event log" mode, the following actions are available:
The transition to viewing the previous event is carried out by pressing the FORWARD key;
The transition to viewing the next event is carried out by pressing the "BACK" key;
The transition to viewing the time and date of the event is carried out with the "*" key, the exit from the viewing of the time and date of the event - the key "*";
Exit from the event log by pressing the "CANCEL" key, or automatically after 30 s.
The "Clock" mode allows you to view and, if necessary, edit the time and date of the system devices.
This mode is available after performing a number of actions:
Use the keys "0", "1" ... "9" to select a zone in the system (for example, 10, ie selection of the 10th zone in the system), the selection of a zone for the device "A6" is carried out according to the principle described in p. .p.3.4.1.1;
Confirm the zone selection with the "#" key;
Confirm the input of the "MASTER" -code of the device with the "ENTER" key;
enter the service menu by pressing key 3 - Service, Figure 8;
by pressing the "FORWARD" key to move to the item "Clock", enter the "Clock" mode by pressing the "ENTER" key, Figure 12;
Figure 12
to edit the time / date, press the "ENTER" key and sequentially enter the current time and date;
after the end of the sequential input of time / date, use the "CANCEL" key to exit the "Clock" mode;
editing the time / date of the current device in the system can be considered complete.
ATTENTION! The time / date editing operation must be performed for each device in the system.
Control Panel A6 Operation manual.
Part II (programming with VPU-A-06 and PR-1) revision 7.03 April 2011 The "Program" mode allows reading, editing and writing of the configuration program for each device in the system and is available after performing a number of actions:
Using the keys "0", "1" ... "9", select a zone in the system (for example, 5, ie selection of the 5th zone in the system), the selection of a zone for the device "A6" is carried out according to the principle described in p. .p.3.4.1.1;
Confirm the zone selection with the "#" key;
Enter the "MASTER" - device code: 1 (factory "MASTER" - device code);
enter the service menu by pressing key 3 - Service, Figure 8;
enter the "Program" mode by pressing the "ENTER" key, Figure 13.
Figure 13
The "Program" mode includes the items:
"Change" - intended for editing the configuration of the "A6" device;
"Write" - intended for recording the edited program into the memory of the "A6" device.
3.4.2 Registration of ID-numbers of devices in the memory of VPU-A-06 Before starting programming the configuration of devices "A6" using the LCD keypad VPU-A, it is necessary to register the ID numbers of these devices in the memory of VPU-A-06.
NOTE: The instrument ID is an alphanumeric string of 8 hexadecimal characters. The ID number is indicated on a sticker on the processor of the device and is unique for each device.
The registration of the ID numbers of the “A6” devices in the LCD memory of the VPU-A-06 keypad is carried out in the “SYSTEM” operating mode, the registration sequence is as follows:
enter the "MASTER" -code of the LCD keypad VPU-A-06: 1234 (factory "MASTER" -code);
confirm the input of the "MASTER" -code by pressing the "ENTER" key;
select the "Service" menu item by pressing the "3" key, Figure 8;
the first item of the "Device" menu will appear on the LCD keypad display, registration of ID numbers is carried out in this menu item, Figure 14;
- & nbsp– & nbsp–
to enter the “Device” menu item, press the “ENTER” key, the serial number of the device and the data (by default 00000000) will appear on the LCD keypad display, Figure 15;
- & nbsp– & nbsp–
to enter the device ID-number, press the "ENTER" key, a cursor should appear under the first character of the 8-digit ID-number in the "Data" line, Figure 16;
- & nbsp– & nbsp–
Control Panel A6 Operation manual. Part II (programming with VPU-A-06 and PR-1) revision 7.03 April 2011 then it is necessary to sequentially enter the ID-number of the device in accordance with the sticker on the processor, after entering each character of the ID-number of the device, the cursor will move to the right, Figure 17;
Figure 17
upon completion of entering the 8-digit ID-number of the first device in the system and for further entering the ID-numbers of other devices by pressing the "FORWARD" key, you must go to the entry of the next ID numbers of the devices "A6";
after entering all the ID-numbers of the system devices, by pressing the "CANCEL" key twice, it is possible to exit the "SYSTEM" mode;
the registration of the system device ID numbers can be considered complete.
The block diagram of the operation algorithm of the VPU-A-06 LCD keypad in the Arming / Disarming, Event Log, Clock and Program modes is shown in Figure 18.
NOTE: XX * Number describing the zone number or key number Figure 18 Control Panel A6 Operation manual. Part II (programming with VPU-A-06 and PR-1) revision 7.03 April 2011 3.4.3 Mode of programming the configuration of the device "A6" using the LCD keypad VPU-A-06 The algorithm of the device (hereinafter - the configuration program) is stored directly in the device itself in nonvolatile memory. To edit the configuration program, it must be read from the device into VPU-A-06.
This requires:
Being in the programming mode (see p. 3.4.1.2), using the "FORWARD" or "BACK" keys, select the "Read" item, Figure 19.
- & nbsp– & nbsp–
press the "Enter" key. A creeping line will appear in the lower part of the display, which shows the percentage of completion of the process of reading the program from the device to the memory of the LCD keypad VPUA-06, Figure 20;
- & nbsp– & nbsp–
Upon completion of the reading process, the program can be viewed or edited:
Press the FORWARD key, select the Change item, Figure 21;
- & nbsp– & nbsp–
The instrument configuration program menu consists of the following sections: "GENERAL"; "PLUME";
"ZONE"; "ACTIVATOR"; "BUZZER"; "SIREN"; "RELAY"; "MASTER"; "GZ KEY"; "MONTER";
"MASTER".
- & nbsp– & nbsp–
using the "FORWARD" or "BACK" keys select the edited section (for example General) and press the "ENTER" key, Figure 23.
- & nbsp– & nbsp–
Control Panel A6 Operation manual. Part II (programming with VPU-A-06 and PR-1) revision 7.03 April 2011 using the "FORWARD" or "BACK" keys select the desired item / address and press the "ENTER" key. A cursor will appear in the "Data" field, offering to enter the required data in accordance with the programming tables, table 2;
to exit the submenu, press the "CANCEL" key;
after editing all the necessary parameters of the program, it must be written into the device configuration memory, for which it is necessary to select the “Save” item, Figure 24.
- & nbsp– & nbsp–
press the "Enter" key. A creeping line will appear in the lower part of the display, which displays the percentage of completion of the process of writing the program from the memory of the LCD keypad VPU-A-06 to the configuration memory of the device.
ATTENTION! The “Write” item of the “Program” mode is mandatory, otherwise, the edited configuration program of the “A6” device will remain only in the memory of the LCD keypad VPU-A-06.
The block diagram of the VPU-A-06 operation algorithm in the programming mode is shown in Figure 25.
- & nbsp– & nbsp–
ATTENTION! If in the programming tables there is a “+” sign in front of a digit when programming several properties at the same time, it is necessary to enter the sum of the digits in the hexadecimal system, see Table 4.
Programming tables for the “A6” device are shown in Table 5.
- & nbsp– & nbsp–
ATTENTION! For correct operation of the "A6" device as part of the "Alesya" ASOS, the "OWNER" keys from # 16 to # 79 CANNOT be programmed.
ATTENTION! The digital PIN-code must not start with 0 (zero), the first digit must be from the row 1 ... 9.
After the program has been changed and checked, it must be written to the device:
Press the "CANCEL" key to exit to the main programming menu.
Being in the main programming menu, select the "Record" property and press the "ENTER" key. The program will be written from VPU-A-06 to the device.
Control Panel A6 Operation manual. Part II (programming with VPU-A-06 and PR-1) edition 7.03 April 2011
4 DESCRIPTION OF DEVICE PROGRAMMING WITH REMOTE CONTROL
PROGRAMMING PR-1
- & nbsp– & nbsp–
4.2 Purpose of keys of the control panel PR-1 READS - reads from the memory of the device to the memory of the control panel the program (ul 01). If the read operation is successful, the indicator displays the sequential movement of the highlighted segment on the rightmost matrix.
REC - writes the edited program from the remote control to the device (dl 01), sets the time (dl 03) and panel code (dl 00). If the write operation is successful, the indicator displays the sequential movement of the highlighted segment on the rightmost matrix.
EDIT - selection of the program page. When this key is pressed, two letters Ed will light up in the left side of the remote control indicator and the remote control waits for the number of the program page to be entered, in which it is necessary to change the parameters. If the program page is open, then when the "EDIT" key is pressed, the display will show the number of this page (for example: Ed 04). The page number is dialed with numeric keys and displayed on the right side of the indicator. When the page number is dialed, the remote control enters the mode of editing the parameters of this page without a confirmation command, and the two leftmost symbols of the remote control indicator display the address of the first cell in this page (00). The two symbols on the right represent the data located in this cell at the current address.
ADR - jump to an arbitrary address within the selected page. When you are inside the page and press this key, there are two digits of the indicator located on the left and displaying the number of Control Panel A6 Operation Manual. Part II (programming with VPU-A-06 and PR-1) revision 7.03 April 2011 addresses, symbols "_ _" are shown, and the keypad is waiting for the address to be entered. After entering, the remote control automatically switches to the dialed address.
DANN - data editing mode for the current address. When you find the required address inside the page and press this key, the two digits of the indicator located on the right and displaying data show the symbols "_ _", and the console is waiting for data input. When viewing the event log, pressing the DATA key leads to a transition to the event viewing mode: the reason for which it caused, the time of its occurrence.
FUNC - selection of additional function. These service functions make it possible to perform set / erase operations as separate loops, relays, etc. in a page, as well as entire pages; copying the properties of loops, relays, sirens, etc. inside the program page.
The console has the following service functions:
erasing the properties of the edited object (FUNC 00);
copying service keys from the remote control memory to the device memory (FUNK 50).
0 - F - hexadecimal digits used in programming mode.
1 - in addition to purely digital, it can also be used as a functional one. So, when inside a page, clicking it will jump one address back inside the page.
2 - similar to key 1, only the transition is carried out one address forward within the page.
EXIT - exit from the mode of the current page, restart the panel when the remote control is in its initial state
- 3rd press.
ENTER - not used.
For A6 panels, the entire address space is divided into program pages that regulate the parameters and properties of individual groups of functional devices: loops, keys, etc.
(see programming tables). To set the system properties, you must select program page 01, within this block the system configuration is determined. For example: the device will operate in the ASOS "Alesya" mode, in this case it is necessary to dial the following (RED 01 - the cell with the address 00 in the program page 01 opens. dial 02 on the right two segments). To set the parameters of the loops, you must select program page 02, inside this block you define the type of loop and its properties.
For example: the 1st loop is a security loop with 4 states, the response time to a change in the loop state is 500ms. To do this, press the keys in sequence: EDIT, 0, 2; ADR, 0, 0; DANN, 0, 1; ADR, 0, 1;
DATA, 2, 0. Lines are divided into zones in the same way (program page 03), programming of activator properties (program page 04), properties of buzzer, siren and relay (program page 05), etc.
To program the keys "OWNER", "MONTER", "GZ" it is necessary to select the required program page. Select the address in the aisles of the program page and attach the key, which is being programmed, to the reader on the remote control. The keypad will confirm successful key recording with a sound signal. If there is a recorded key in the aisles of the program page at the selected address, then there will be two dashes (- -) in the data bit, otherwise two zeros (00). If you attach a key when two dashes are displayed, then the previously recorded key will be deleted, and the attached one will take its place.
Example:
record of the key "OWNER" No. 1 (RED 06; ADR 01; attach the key). Key entry "ГЗ" No. 3 (RED 07; ADR 04;
attach key). If you write the keys "ГЗ" to program page 12, and "MONTER" to program page 13, then the keys are stored in the memory of the remote control. Using FUNK 50, the service keys can be transferred to the device memory.
Connect the PR-1 control panel to the ХP1 connector of the control board. After switching on, the display shows the version number - "Pt-3" for several seconds. Then an invitation appears to dial the 4-digit Master Code of the remote control (in the form of the string "__ __"). After dialing the correct Master-code, the remote control automatically detects and indicates the type of the connected device, for devices "A6" the line is displayed: A6.
Then it is necessary to enter 4 digits of the Master-code of the device.
NOTE: If the master code of the device has less than 4 digits, then the missing digits are replaced, when entered, with zeros at the end of the password. For example, if the device password is "35", you must dial: "3" + "5" + "0" + "0".
All “A6” units have a “1” password after sale. The same password is set after "zeroing" the device memory.
ATTENTION! If the device password contains more than 4 digits (for example, set from a PC), it is impossible to access such a device using the remote control. For further notes on the password, see the "Instrument Password" chapter.
If the device password is entered correctly, the device enters the programming mode, and the display of the remote control shows the current value of the device clock in the format: HH.MM.
Reading the program from the device to the remote control is carried out by successively pressing three keys: "READ", "0", "1".
Recording of the program from the remote control to the device is carried out by successively pressing three keys:
"REC", "0", "1".
Writing a new password to the device is done by successively pressing three keys: "REC", "0", "0".
The instrument properties program is divided into 8 pages.
The entrance to the program page is made by successively pressing three keys:
Control Panel A6 Operation manual. Part II (programming with VPU-A-06 and PR-1) revision 7.03 April 2011 "EDIT", "X", "X", where X is the number of the page containing the parameters that need to be changed.
After selecting a page, the 2 left digits of the indicator show the address of the program cell, and the 2 right digits
- the value of the data contained in this cell. In contrast to the display for other devices, for A6 devices, the cell address and its value are always represented by two numbers in hexadecimal form. Those. to set time parameters, it is necessary to convert numbers from decimal system to hexadecimal. The left tetrad has a time factor of 16, the right one - a factor of 1. To select a time up to 15 seconds, 15 minutes, program the corresponding element only in the right tetrad, and in the left tetrad "0".
- & nbsp– & nbsp–
To select times that are not included in the above tables, program both notebooks:
1. For the selected function, select the appropriate time in the units that are shown (all - in seconds or minutes) - but not in minutes and seconds at the same time.
2. Divide the selected time by 16. Enter the quotient in the left notebook, and the remainder, translated from the table
To the right.
3. Check the items by adding the contents of the left notebook multiplied by 16 and the right notebook.
EXAMPLE: Program an Entry Delay of 1.5 minutes.
1. The Entry Delay (Address 02) is measured in seconds, so the delay time is 90 seconds.
2. Divide the time by 16: 90/16 = 5 (quotient) + 10 (remainder). Enter the quotient in the left tetrad, and the remainder, translated according to table 2. - into the right one:
address 02 data 5 A Private Balance
3. Check the elements (remember - element "A" = "10"):
5 x (16) + 10 = 90.
Table of correspondence:
Time \ Sum 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Data 1 2 3 4 5 6 7 8 9 A B C D E F ATTENTION! If in the programming tables there is a "+" sign in front of a digit when programming several properties at the same time, it is necessary to enter the sum of the digits in the hexadecimal number system, see the table.
Complete the tables below before starting programming.
When programming, it is convenient to use the following service functions of the remote control:
FUNC 00 - cell erasure;
FUNC 01 - erasing the program page;
FUNC 50 - copying of service key pages from the remote control memory to the device memory.
- & nbsp– & nbsp–
Control Panel A6 Operation manual. Part II (programming with VPU-A-06 and PR-1) edition 7.03 April 2011
Setting the instrument clock:
It is necessary to press the "Count" button on the remote control and, after the inscription "ul - -" appears on the display of the remote control, enter the numbers "01"
To view and enter the current time, press the "Edit" button on the remote control and, after the "Ed - -" inscription appears, enter "14". Two digits of the ordinal address and two digits of the time will appear on the display of the remote control.
You can scroll by using the number buttons of the remote control "1" and "2", or by going to the addresses explicitly by pressing "Addr" and, after appearing on the left notebook of the remote control indicator "- -", enter the desired address.
"Dunn" - the mode of data editing at the current address. When you find the required address inside the page and press this key, the two digits of the indicator located on the right and displaying data show the symbols "_ _", and the console is waiting for data input.
Viewing the event log using the PR-1 programming panel The presence of a timer chip in the device allows viewing the event log using the PR-1 programming panel with reference to the time of the event.
To do this, press the "Count" button on the remote control and, after the message "ul
- - ", enter the digits" 02 "(if the log is read successfully from the device memory, sequential running of the highlighted segment on the last matrix of the programming panel indicator will be observed).
To view the event log, press the "Edit" button on the remote control and, after the "Ed - -" message appears, enter "21". The indicator of the remote control will show two digits of the ordinal address and two digits of the code of the event that occurred. You can scroll through the magazine either using the numeric buttons of the remote control "1" and "2", or by navigating to the addresses explicitly by pressing "Addr" and, after appearing on the left notebook of the remote control indicator "- -", enter the desired address.
Attention! Please note that the order of events in the log is stored in reverse order, i.e.
the event at the ordinal address "00" occurred later than the event at the ordinal address "01", and so on.
By pressing the "Dann" button on the remote control and using the "1" and "2" buttons to change the address (the address "-0", "-1", "-2", etc. appears on the remote control), each event: the reason that caused it;
key marks; the time when the event occurred. The volume of the log is determined by the size of the memory installed on the card and can be for 128 events, expandable up to 512 events.
Geoinformatics. This is a set of algorithms (functions) that provide the analysis of location (placement), connections and other spatial relationships of spatial objects ... ”I.N. Blinov, V.S. Java romance. INDUSTRIAL PROGRAMMING Practical guide Minsk "UniversalPress" UDC 004.434 BBK 32.973.26-018.2 B69 Authors: Associate Professor of the Department of Numerical Methods and Programming of BSU, Candidate of Physical and Mathematical Sciences I.N. Blinov, associate professor, head. Department of Numerical Methods and Programming, BSU, Ph.D. Phi ... "
"Methodological instructions (explanatory note) The work program of the discipline" Programming "Designed for daytime students of the 1st year, 2nd semester in the specialty: _Physics _ 010701.65 in the specialization:
"Topic 9. Logical foundations of computers. 1. Logics. Information processed in a computer is represented using physical quantities that can only take two stable states and are called "..."
Shcherbinina Libraries of Ural universities: problems and work experience Issue 9 Scientific electronic publication Prepare ... "preparation: 010400" Applied Mathematics and Informatics "faculties: FIVT, FRTK Department of GENERAL PHYSICS course III semester 6 Labor intensity: those ..." ELECTROMAGNETIC BRAKING SYSTEM I.I. ZABENKOV1, V.V. KIKINEV2, D.A. ENKOV1 Belarusian State University and ... "distributed C ++ programs using Win API Abstract: this article provides a verification method ..."
Materials on this site are posted for review, all rights belong to their authors.
If you do not agree that your material is posted on this site, please write to us, we will delete it within 1-2 business days.
Fire alarm control panel for 6 loops (2 relays, expansion up to 6).
Indication of the state of the system and alarm loops is carried out on the front panel of the device; if necessary, it is possible to organize monitoring of the status at remote observation posts using remote control panels with LCD display VPU-A-06 and LED display panel VPU-A.
The A6 devices support the data transfer protocols of the Alesya, Molniya, STARS, Mayak, CORTEX, LARS, Ademco systems, as well as the ability to transfer over Ethernet when connecting the appropriate matching module: ISA -8, adapter GSM, IS-RF, IS-Monitoring station, IS-AD, IS-ETHERNET.
Functionality:
- Discernment 4 states(normal, alarm, sensor alarm, malfunction) for security and 5 states for fire loops (norm, attention, fire break, short circuit).
- Division of loops into independent zones, depending on the version of the device, from 1 to 6.
- Flexible programming of functions and properties of loops In 3 ways to choose from: using a PC, a PR-1 programming panel and a VPU-A-06 keyboard.
- Formation of the "ALARM ALARM" notification when replacing the Control Panel as part of ASOS "Alesya".
- Generation of the "OPENING ALARM" notification in the event of a break in the connecting wires of the access device.
- Controlled on "Break" and "KZ" output for connecting technical means of notification.
- Built-in 80 dB buzzer.
- Zone disarming confirmation button.
- Organization of 2 to 6 relay outputs when connecting a relay module.
- Universal external digital bus RS-485 for connecting devices into a network and monitoring their status using the VPU-A-06 or VPU-A-16 keyboard when connected to the KSO-A module.
- Built-in power output for external devices.
- System shutdown when the battery is deeply discharged.
- Arming using PIN codes from keypads VPU-A-06 and VPU-A and / or electronic keys DS1990A, etc.
Communication channels with the monitoring station:
- radio channel 135 ... 175 MHz;
- radio channel 433.92 MHz;
- busy subscriber lines of the city telephone network;
- local area network (Ethernet);
- GSM (GPRS, DATA, SMS).
In the case of use in fire alarm systems, the device allows you to generate a trigger signal for fire control devices ASPT using built-in relay outputs and outputs of additional relay modules RM-64, RM-64-2, RM-64-6.
User manual
A6 devices for a given use case can be programmed in one of four ways to choose from:
- using a PC using the IS-232 module, or the PROG-1 module and
specialized software "Programmer Ah";
- using the PR-1 programming panel and the tables corresponding to it
programming;
- using the VPU-A-06 keyboard using the IS-485 module and the corresponding
programming tables;
- using the VPU-A-16 keyboard using the IS-485, KSO-A and
the corresponding programming tables.
To program the devices, it is necessary to edit a number of groups of parameters highlighted in certain program pages. After editing, the changed configuration is written into the non-volatile memory of the device.
The A6 contains the following program pages:
- "GENERAL" ("PARAMETERS"): the general properties of the A6 device are set, the selection is made
automated security system and type of radio channel;
- "LOCKS": the parameters of each of the signaling loops are determined;
- "ZONES": set the properties of the arming / disarming zones and the correspondence of the loops to the zones;
- "ACCESS": defines the properties of access control systems;
- "ACTIVATORS": the parameters of the operation of external devices (buzzer, SDU, relay) are selected;
- "KEYS": enter user keys ("OWNER", "GZ", "MONTER" and "MASTER").
Programming the parameters of the A6 device using a PC is one of the most convenient and intuitive ways. This programming option makes it possible to create an archive and store the program settings of each device in the form of files on a PC, which allows you to restore at any time the full configuration of the device on any of the objects. Also, in addition to programming devices, specialized software makes it possible to monitor devices connected to the network and view all events occurring in them.
It is recommended to use the PR-1 programming panel and VPU-A-06 keyboard when
programming the device or promptly making changes to its program settings directly at the facility.
In the case of programming using PR-1, the parameter values are entered in a hexadecimal code into the corresponding memory cells of the console, according to the programming table, with the subsequent transfer of the entire program from the PR-1 console to the nonvolatile memory of the device. Also, the convenience of using the PR-1 programming panel lies in the possibility of storing in the PR-1 non-volatile memory of the electronic keys of the services: "GZ" and "MONTER" (keys of the contact method of reading DS1990A, DS1991-DS1996). And, if necessary, the prompt transfer of the key data codes to
memory of the device A6.
When programming with VPU-A-06, the program settings of the panel are first read into the keyboard memory and after editing, in accordance with the programming tables, by writing are entered into the non-volatile memory of the A6 device.
When combining A6 devices into the “Network A” ISB based on KSO-A, programming the configuration of devices is possible using the VPU-A-16 keyboard. When using this programming method, the program settings of the panel using VPU-A-16 are read into the KSO-A memory and, after programming the device configuration for a given use case, they are entered into the nonvolatile memory of the device by writing.
2 DESCRIPTION OF PROGRAMMING OF DEVICES "A6" ON A PC
2.1 Description of versions of the "Programmer Ah" software
Ax (4.5.2.ХХХ *) Light.exe is a freeware program. Allows to carry out
programming of configurations of devices "A6" and "A16-512".
Ax (4.5.2.ХХХ *) Full.exe - commercial version of the program. Allows to carry out:
- programming of configurations of devices "A6", "A16-512" and KSO-A (controller KSO-
A);
- monitoring up to 32 devices of the "A6" series in the network connected to one COM-port of the PC with
displaying service and alarm messages on the monitor screen from devices with
description of loops, zones, ACS and keys;
- monitoring up to 32 KSO-A in the network connected to one COM-port of the PC. To the controller
KSO-A can be connected to up to 32 devices.
* NOTE: XXX software version.