The cartridge is an important piece of any mixer that is responsible for water supply and its adjustment. But over time the cartridge fails, so you have to repair the cartridge in the kitchen, in the bath or soul yourself. The replacement of the mixer is not a complex thing, but rather responsible, so, first of all, calculate your strength and think - whether you can repair the crane and eliminate the breakdown of this device.
Building:
How to change the cartridge in the mixer? Quite simple. The main thing is to correctly determine the reasons for the breakdown, and then you can replace the cartridge with your own hands and fully fix and change the crane device.
Causes of breakdown
The causes of the mixer design breakdown in our time. First of all, it is possible to attribute firm and small particles into it to the rapid breakdown of the cartridge in the crane and the subsequent replacement. Because of them, in the mixer, there is a violation of the internal elements, that is, erasing the metal parts of the crane and head. As a result of this interaction, chips, scratches and other damage appear on them, which are the main cause of the tap.
When these features appear, it is better without tightening to repair and replacing the cartridge, as well as change the remaining parts of the mixer design.
When is it time to change the mixer?
At the same time as a question - when to change the cartridge in the mixer, you can also ask - when is it better to change the mixer and how to properly carry it out? Expert opinion reads: mixers in the kitchen, in the shower and bath can last long enough. The main timely to replace or repair the cartridge, as well as change the gaskets. But when did the device be out of order? Of course, yes.
Experts say: replace the mixer as in the kitchen, so in the shower and the bath you need at the moment when the design of the crane is completely laughed and the repair will not help her. Most often, such "breakdowns" are happening with the head, cartridge and other components of any crane. Over time, every detail of the mixer will deteriorate, but it makes no sense to constantly replace it, since the tap just "worked out".
Therefore, after the cartridge breakdowns and other crane designs, it must be replaced so that you can not spend money on repair. To find out when it is better to replace the mixer and install a new cartridge in the kitchen, in the bath or soul, we advise you to see the thematic video or photo.
Replacing the cartridge in the mixer do it yourself: video
How to replace the cartridge in the mixer yourself? In fact, it is easy. The main thing is to know the structures of the crane and then you will get a quick repair of the mixer, replacing the cartridge in it.
Before starting replacing the cartridge in the mixer, it is better to get acquainted with the photo and video to have an idea of \u200b\u200bthe upcoming repair.
To replace the cartridge in the ball mixer and completely eliminate the design breakdown, a number of actions must be performed.
- Early water in the mixer.
- Remove the plug (plastic).
- Using a screwdriver, unscrew the screw, and then carefully pull the handle.
- Then unscrew the decorative lid located under the tap lever.
- Under it, you will see the locking washer that also needs to be removed from the design of the crane using a confront key.
- After that, pull out the cartridge. If there are settled cartridge near the pads, pull out the cartridge is quite difficult (see photo).
- The released space under the cartridge wipe from sand, plaque and other garbage.
- Now we replace the cartridge: carefully insert a new cartridge into the device and fix it with a washer, and then decorative lid (if you need to change the gaskets, it is necessary to do it now).
- After that, put the handle in place and fix it with a screw.
Now insert the plug and check the operation of the mixer and the cartridge. You did everything right if the crane does not flow, and the handle turns smoothly. On this, the repair of the crane design device and replacing the cartridge is completed.
It is worth noting that the installation of a similar mixer can be carried out both in the kitchen, so in the bath and soul, therefore, in this case, the repair and replacement of the cartridge will be identical (especially since it is not difficult to change it in any "part of the house" in the same way).
To visually see the upcoming work, view the best photo of the cartridge replacement in the mixer, as well as read its installation process and as best you can deal with its device.
Replacement in the shower mixer
The cartridge in the mixer is capable of breaking not only in the kitchen, but also in the bath. Independently repair and replacing the mixer in the shower is easy. Most often, in the bath install single-art mixers, which differ slightly on the device, designs and replacing parts from the ball. But, nevertheless, it is possible to replace the cartridge in such a mixer quite easily, especially if you contact the best photo and video capable of describing the process in brief and show the replacement of the upcoming crane repair.
- Blind the water in the mixer.
- Just in case, check the correctness of the cartridge.
- Remove the plastic part and unscrew the screw (see photo).
- We take out the handle and unscrew the remaining parts that do not allow the cartridge to pull out.
- After that, we clean the crane device from scale and sand (as it is done, look at the photo). It is important to do as the cartridge setting so that the device is not clogged.
- Then check the sealing rings on the cartridge, because if you have an incorrect installation, the mixer after repair will flow.
- We put a new cartridge in the mixer and check whether it is suitable in size. When installing it is important to check the holes in the cartridge, the device of which should match the mixer (what the device looks like, look at the photo).
- After that, we return the crane to the original condition and check the quality of your repair.
As you can see, change the item is not difficult - see the replacement process in the photo.
Such a replacement of the cartridge in the mixer is not much different from the previous repair. And if you still familiarize yourself with thematic videos and photo lessons, you can quickly replace the cartridge and check the device of the mixer for a breakdown.
The design of a single-art mixer on the device is much clearent by the ball, so you can easily replace the mixer in the soul without the help of specialists, especially since in the bath it is much easier than in the kitchen.
How to make a replacement in the kitchen mixer
Create a replacement of the cartridge in the kitchen mixer or carry out its repair using several tools and certain knowledge. The technology of this work is not particularly different from the previous methods of replacing the mixer.
The main difference of such repairs is a ball mixer, which differs significantly from other cranes by its device. In addition, the installation of the cartridge in the ball mixer, located in the kitchen, is a little more difficult, therefore it is better to first get acquainted with the technology of the upcoming repair.
In order to correctly understand the technology of work, you can familiarize yourself with thematic videos and photo lessons, which clearly shows a picture of the mixer replacement, as well as a crane device located in the kitchen.
- Blind the water in the mixer.
- Remove the plastic design.
- Then, with a screwdriver, we remove the bolt (see photos).
- I pull out the handle and start unscrew the remaining details of the device that interfere with getting to the cartridge.
- After that, pull out the cartridge and evaluate its breakdown. If the mixer began to flow or tightly open water, then the breakage is most likely in the cartridge.
- We carry out the installation of a new cartridge in the mixer and collect a tap back.
- If the device inside contains a lot of scale, you can delete it with any cleaning agent. It is important to make it before installing the cartridge so as not to damage the gaskets and the other components (how to do it, look at the photo).
As you can see, replacing the cartridge in the kitchen mixer is not difficult. True, it is better to do this after familiarizing with the thematic photo, since in this case it will change this item much easier.
Differences of cartridges of different manufacturers
The difference between this part for replacement in the mixer of different companies is usually insignificant. However, some try to understand the main differences as much as possible to buy a high-quality and reliable cartridge to replace it in the mixer.
- GROHE produces carbon-crystalline coating cartridges located on the plates, which makes the cartridge more durable and reliable, and the installation is easy.
- ORAS Cartridge is standard, so after the cartridge breakdowns you can quickly and easily find it.
- The manufacturer Vidima offers buyers cheap design cartridge designs for mixers, but they, unlike previous, quickly break, and it is impossible to carry out their repair.
- The boltic trademark sells the best cartridges, which, with a special way of fastening, will serve you for many years.
Choosing a cartridge for a mixer located in the kitchen, in the bath or soul, it is worth considering not only the price, but also the quality of the goods on which the duration of the mixer, installation and reliability of the design depends.
Price
To change the cartridge in the mixer, it must be bought. But how to choose the correct cartridge, if in our time there are quite a lot of models? First you need to decide that you are more important - the best price or quality. After all, change the cartridge in the kitchen, in the bath or soul is easy, the main thing to buy a proper cartridge.
Today, the price category for cartridges for mixers is quite diverse (see photo). If your mixer breakdown comes from its device, check out the table to have an idea of \u200b\u200bthe value of this part for the mixer.
To change the mixer cartridge, you will need not only a new cartridge, but also gaskets that play an important role in the work of the crane.
Following the advice of an experienced expert, you can quickly and easily change the cartridge on the mixer, without resorting to the services of a professional.
- To independently change the cartridge, you need to get acquainted with the video of this installation, which will help you to properly recognize its device.
- Replacing the design of the cartridge when breakdown in the kitchen, in the bath or soul is a similar process that requires certain knowledge and the same tool.
- The best cartridges for the mixer is worth buying in specialized stores.
- The design of this device is quite simple, therefore, repair the cartridge, and anyone can change it in the mixer.
- To assess the degree of breakage of the mixer, to begin with, it is better to figure it out in its device. To do this, you can familiarize yourself with photos and videos, which will explain in detail what the mixer design device.
- All of them, however, have their own deadlines, after which some of their elements fail and require urgent replacement. It should be noted that at present, mixing devices of various types are used to control water flows in waterways in plumbing highways. In recent years, so-called single-art mixers are increasingly used for these purposes, in which switching and adjusting the water flow is carried out using one control handle.
It is also known that the most vulnerable place of such devices are the cartridges that are included in the process of operation intensive wear.
Types of faults
The repair of a single-art-type mixer is represented by the simplest operation that does not require any special skills from the rank. To implement it, you will need to purchase a new cartridge, freely sold in the plumbing department of any economic store.
Below you will be able to familiarize yourself with the list of characteristic faults, indicating the need to replace the intact cartridge:
- violation of the normal flow control of water flows (regardless of the position of the control lever through the crane proceeds only hot or only cold water);
- the impossibility of full overlap of water flows (both hot and cold);
- inconstancy of the temperature of the incoming fluid at the same position of the mixer lever;
- the impossibility of obtaining the required water pressure;
- difficult to move the lever.
Required tools and materials
To conduct the cartridge replacement operations, you will need the following tool:
- ordinary flat screwdriver;
- the hex key (used for certain types of mixers);
- rozhkin or adjustable wrench;
- passatia or pliers;
- calipers.
In addition, you will need to prepare a piece of clean flannel tissue and a special cleansing fluid WD-40, after which it will be possible to disassemble the faulty crane (bumping the water supply channels to the apartment highway).
Removing the cartridge from the mixer
- To replace the element of a single-art mixer, first of all, you should find a hole with a decorative plug on its housing, on which there is a pointer of water supply direction. Then, using a thin scolder, it is necessary to carefully pick up the plug recessed into the housing and completely remove it from the crane. To perform this operation, a well-pointed kitchen knife can also be used.
- After you delete the cap - an oval cavity with the lever fastening is located in it. Having unscrewed this screw, you can remove the lever from the cartridge, for which you need to slightly pull it from yourself and up. Depending on the specific type of dismantled mixer for turning the screw, you will need a typical screwdriver with a stinging of a width of about 3-4 mm or a hex key ".
- After several revolutions produced using the prepared tool counterclockwise, you can easily remove the lever from the pin of the cartridge.
Note! Frequently noted when the accurate screw cannot be unscrewed by any of the known methods. In this case, it is necessary to process it with a special means of the WD-40 brand, used to attenu the accurate contacts. After a small excerpt (about 3 minutes) it will be possible to make another attempt and try again to unscrew the mount.
It should not be made too much effort, since you can simply break the disassembled mixer. In the event that this technique did not help - you will have to resort to the power method of exposure, when using the lever, the removable lever is simply laid out with a part of the cartridge that has come into disrepair.
After the fastening nut is removed (or the lever is broken and removed) - you can easily remove the cartridge from the mixer housing. Before replacing the cartridge in the mixer, you should use the calibration of the seat of its landing into the case. Such measurements are needed so that when buying in the store you can unmistakably choose the item suitable on the landing size (sometimes it is enough to bring a removal cartridge as a control sample).
Video
More The process of replacing the cartridge is presented in the following video instructions:
The cartridge is the main functional mechanism of a single-art mixer, since it is he who is responsible for the process of supplying water, regulates its intensity, and also mixes hot and cold streams that come from the water supply system. In the event of a device breakdown, it is necessary to replace it as quickly as possible to exclude the likelihood of the leakage of moisture at the bottom of the mixer.
It is possible to carry out this procedure independently without the help of specialists, and it is necessary to comply with the sequence of the technological process.
Types of cartridges
The ratio of cold and hot water flows in the mixer depends on which position is the control device - a crane or lever. Modern lever faucets are currently equipped with different types of devices.
Consider them in more detail.
- The ball cartridge, its design is represented as a steel bowl, three holes in which they communicate with each other. With the help of the lever, the product is connected to the transfer mechanism. As a result, the processes of opening and closing passage channels occur, as well as the control of the intensity and temperature of the total flow.
The principle of operation of the lever consists in the displacement of the upper ceramic plate with holes, relative to the remaining planes located in the same plane.
- The cartridge presented in the form of a plastic cylinder, at the top of which is located the control lever. The principle of operation and functions of this device are similar to the previous type of design.
To replace or repair the ball cartridge is almost impossible, since the details of such a design manufacturer configures with great accuracy, while any intervention can disrupt the correct functioning of the device and deduce the crane.
In the case of replacing the cartridge, much less difficulties arise, to perform this manipulation, it is enough to know the sequence of performance of work and take into account the specifics of a product of a trademark.
Signs and reasons Cartridge breakdowns
In the process of exploitation of the mixer, unforeseen problems and breakdowns are often arising and it is not surprising, since this device man uses no one-tenth time during the day.
The main features of a faulty cartridge state.
- The design of the structure from the side of the lever. The problem occurs in the process of turning on the device and is accompanied by the occurrence of water droplets on its surface.
If you do not take timely measures to eliminate the cause of the accident, in the process of the subsequent discovery of the crane, the leakage intensity will increase.
- Violation of work modes. For example, instead of feeding hot water flows cold, or as a result of mixing two streams of water, its temperature does not correspond to the position of the lever.
- The inability to open or closes the mixer, regardless of the position of the control crane.
The above features indicate the likely failure of the cartridge. However, it is necessary to replace or repair the installation, it is necessary to find out the cause of the construction breakage to eliminate the likelihood of a quick failure of a new product.
Consider the causes of the rapid wear of the cartridge.
- Low quality purchased product. The most vulnerable place in the design is the head of the lever, which is subject to the constant effects of mechanical load. If in the process of its manufacture the unfinished manufacturer initially used not high-quality material, unfortunately, quick wear and breakdown cartridge avoid.
- Poor quality of running water. As a result of solid particles, mechanical damage to the structure occurs in the installation. This problem results in disrepair only those mixers in which there is no filter of tap water.
In order to minimize the installation of the installation, it is necessary to install a filter that will regularly clean the water from impurities of dirt, salts, large particles that are capable of irreparable damage to the product.
- Excessively applied force, which is also able to bring the mixer.
When using the design, the opening processes, the closing of the crane, as well as the adjustment of the flow of water to produce smooth movements that do not require considerable efforts.
Thus, the above measures will help increase the life of the device, but if the breakdown has already arisen, do not hurry to call a specialist, since the cartridge replacement can be replaced independently.
Cartridge replacement technology
Replacing the cartridge in the mixer will not require special knowledge and special efforts, even a schoolboy may carry out this procedure. However, it is necessary to first familiarize themselves with the rules and recommendations of the technological process.
Consider the sequence of work on the replacement of the cartridge.
- First of all, it is necessary to overlap the water supply from the riser. After that, it is necessary to raise the design lever upwards, at the bottom of it, find a cap, which is unscrewed using a screwdriver. The screw located under it, you need to weaken a little to remove the lever of the mixer. Next, you should unscrew the chrome decorative cap, which is under the removed lever.
- After removing the cap, it is necessary to remove the nut that holds the broken cartridge.
Before installing a new product, a small cleaning should be done. It is as follows: Clear the seat of the cartridge from the dirt and solid ceramic particles accumulated during operation, which arise as a result of the destruction of the mixer discs.
- The new cartridge is placed in the mixer in such a way that the protrusions on it coincide with the holes that are located on the landing location.
- Next, you should fasten back the nut, install a decorative cap, joystick, as well as a screw cap.
- Open a faucet and check the mixer for performance, make sure that there is no leaks.
Remember, even in case of problems, it is not necessary to despair, it is enough to overlap water and proceed to the elimination of admitted flaws.
As you can see the replacement of the cartridge easily, this process will take no more than an hour. At the same time, the correctly installed product will delight long service life.
Look also at the roller about replacing the cartridge in a single-grazing mixer
Owners of unclear cranes from time to time face a problem in its work, which requires a replacement of the cartridge in the mixer.
These types of mixers are designed both for the shower cabin and for installation on the sink, including in the kitchen.
It should be noted that the procedure for replacing the cartridge is the same for the mixer from the shower cabin and for the crane in the kitchen.
In most cases, such single-art faucets have a standard cartridge made of ceramic material that can be completely quietly acquired in absolutely in any specialized store.
The process of working on the replacement of the cartridge in the mixer (including for the shower cabin) is so simple that it will be able to master it without any problems with his own hands.
Despite the relative simplicity of the replacement process of this element of the crane, it is necessary to approach it responsibly, remembering that it is the cartridge that is the heart of the mixer, and its subsequent trouble-free operation will depend on the quality of work.
In more detail about the cartridge device and the process of its replacement, you can see the video located below.
Principle of operation and main fault of the cartridge
For a single-grazing mixer, which in our time is very popular, it is the cartridge that is the main functional element.
It makes it possible to control the flow of water literally in one movement (including for the shower cabin).
Due to the adjustment of a single handle located on the mixer, it is possible to completely easily serve both hot and cold water not only in the tap in the kitchen, but also in the shower.
In addition, due to the possibility of fixing the position of the handle disappears the need to constantly adjust the ratio of the incoming hot and cold water from the mixer.
This function of a single-art mixer is very convenient for the shower. The cartridge itself consists of two separate plates that are most closely adjacent to each other.
By changing their position relative to each other and the necessary adjustment of the flow of water is performed.
Like any other device, the mixer cartridge can eventually fail, which means it will be necessary to replace it.
The fact that it is necessary to urgently change the cartridge in the mixer, may indicate the problem with the adjustment of the flow of water.
For example, regardless of the position of the mixer handle, only cold or hot water flows from the crane.
In addition, the adjustment can be broken when it does not turn on only hot or only cold water.
It is also quite often when the water cartridge fails at the same position of the handle at each new opening has a completely different temperature.
In addition, the handle itself can walk enough tight, as well as when it is brought into the position of overlapping water flow, the liquid continues to flow from the crane.
Any of these faults suggests that the faucet cartridge has been worked out, and therefore it is necessary to urgently replace it.
With this task, everyone who has at least a minimal view of the plumbing will be able to cope with their own hands and watch the video posted below.
Operating procedure
Replacing the cartridge in the mixer, regardless of where it is installed, on the sink in the kitchen or on the shower panel, starts with the preparation of the appropriate tool.
To work, it will be necessary, first of all, the screwdriver and the hex key, as well as the adjustable key, pliers and the special composition of WD-40, which will help promote oxidized and rusted compounds.
Before starting work, it is mandatory to overlap the arrival of both hot and cold water on a riser of an apartment or at home.
After that, it is necessary to carefully look at the crane lever and find a decorative plug on it, which you want to remove to access the fastening.
The screw under this plug should be unscrewed, after which the lever itself is removed that regulates the water supply.
This stage of work does not represent a special complexity and completely simply performed its hands.
In some cases, remove the water adjustment lever is quite difficult. If the reason lies in the rusty fastening screw, then the WD-40 means should be used.
It is injected into the connection itself and after a couple of minutes the screw must unscrew. In the case when it did not help, you will have to apply physical strength to remove the lever.
To do this, it should be as much as much as possible, but carefully several times to pull it up, and it must move together with the top of the old cartridge.
After the lever is dismantled from the mixer, begged to unscrew the decorative lid located under it, in the direction counterclockwise.
As a rule, it is removed by hand, however, if difficulties arose, then you can resort to the help of pliers. This operation is done carefully so as not to deform the edges of the decorative cover.
After dismantling the decorative lid on the mixer, access to a large nut, which also needs to be accurately removed.
It is unscrewed using a filter key, it should not be made of sharp jerks and make an excessive force.
If the nut is not amenable to use the composition of WD-40, which quickly softens the flare and rust.
After the nut is completely rejected, you can remove an old faulty cartridge.
Before installing a new cartridge in the mixer in the mixer, it is necessary to thoroughly clean the internal space of the crane.
This can be done with a dense tissue, which is convenient to remove the entire flask and salt sediments.
At the final stage, water supply is restored and the operation of the mixer itself is checked. You can cope with this work with your own hands without assistance.
This is primarily due to the fact that the mixers have different models, respectively, and regulating the water flow of the device may have dimensional dimensions.
As practice shows, the mixers installed on the shower panels are slightly different from the mixers installed on the sink, respectively cannot replace each other.
It is best to remove the Cartridge to be replaced and go to the store for a new one with it.
On any cartridge there are two protrusions that, when replacing, must completely coincide with the holes on the mixer housing. Only then can be said with confidence that the cartridge approached and will not flow.
When replacing the old cartridge on a new one, it should be especially accustomed to remove the decorative ring, since if it is strongly damaged or deformed, then it will be very difficult to find a similar.
Despite the seeming simplicity of the process of replacing the old cartridge in the mixer to the new, all work should be accurately done.
Excessive effort should not be made when unscrewing any mounts, as you can not only thread the thread, but also damage the mixer itself.
With the right approach to the case and availability of the entire necessary tool, the work on replacing the mixer is performed without assistance to your own hands as soon as possible.
If the mixer fails occurs, many people think that it must be changed. Do not be upset ahead of time, because most often the cause of the problem is the cartridge is the detail of the mixer, which is inexpensive and easily changes even non-professional.
Features
At the moment, two types of mixers are used: two-dimensional and single-art. The first option is more outdated, it is a classic tap with two valves that are responsible for the supply of hot and cold water. The single-dimensional mixer, respectively, has one lever, and the water temperature in it is adjustable using its turn to the left and right. The pressure is adjustable to the height of the lever lifting. This type of mixer is considered more convenient, as it allows you to quickly achieve the desired water temperature due to the device itself, because it does not have rubber gaskets with low wear resistance. It allows you to save the desired position in the closed state, respectively, there is no need to configure it every time. And the obvious advantage is that one lever is still easier than two valves.
The cartridge is the main functional part of the mixer, which is responsible for mixing hot and cold water coming from different pipes. They also have two species. Two-dense mixers imply the use of exclusively disk cartridges, while in one-lugenous there are both ball and disk. In fact, there is no fundamental difference in these types of cartridges.
The ball cartridge works on the following principle: cold and hot water is fed to the ball and stirred inside it, then it comes out, already possessing the desired temperature. It is necessary to have a special resolution on the production of the ball cartridge, so the manufacturer chooses the disk.
This type of cartridge is characterized by its more complex device:most often it consists of two metal-ceramic plates that are completely non-transmitting water enclosed in a plastic case. Plates are tight pressed to each other. The lower plate always remains fixed, and the upper displacement leads to changes in water supply. It connects with the lever of the mixer with the help of a special rod, and as a result of the displacement of this lever vertically, the water pressure changes, and the rotation to the side affects its temperature. If there is a breakdown, many think that it is worth replacing only a faulty cartridge item, however, it is irrational. Since there is no guarantee that you can accurately establish what exactly the problem is, as well as no one produces individual details, as it is believed that it is easier to replace the entire item immediately, respectively, the cartridge is an indisidated part.
Disk cartridges are diameter from 35 to 47 mm, but most often occurs either 35 mm or 40 mm. There is no fundamental difference in them, but when replacing it is worth considering the diameter to buy such a cartridge that is suitable for a particular mixer. The manufacturer of the cartridge declares that its service life is about 10 years, although in practice it turns out that this period is heard strongly. Problems often arise after 4-6 years after purchase. So that the breakdown did not find surprise, it is worth buying a mixer, take a spare cartridge for it. Then, in case of problems in its work, it will not be necessary to spend time searching for a suitable part in the store. Especially since this item is inexpensive - an average of 150 to 300 rubles.
When you need a replacement?
The cartridge is a detail located in the inside of the mixer.
It is impossible to see his work directly, but there are the following signs, allowing to identify malfunctions:
- the lever of the mixer is tightly rotated, hoored;
- it is impossible to completely overlap the faucet or water leaks, even in its closed position;
- the maximum water pressure is not included;
- the water temperature changes even in a fixed position of the adjustment lever;
- the position occupied by the lever does not correspond to the water temperature;
- water accumulates around the mixer, which indicates its flow.
Causes of breakdown
Faults usually arise due to the following factors:
- improper operation of the mixer, exposure to mechanical effects;
- low quality water is the presence of metal impurities, salt sediments;
- the quality of the materials from which the cartridge is completed or the mixer itself does not meet the requirements;
Part of the problems will help prevent the additional filter on the plumbing. In this case, you can avoid damage to the inner parts of the device caused by poor-quality water.
Required tools
In the process of replacing the cartridge there is nothing complicated.
First of all, it is necessary to prepare all the required tools, such as:
- hexagon or flat screwdriver;
- key for removal (violation or gas);
- a rag for cleaning the inside of the mixer;
- wD-40 liquid;
- new replacement cartridge.
How to change with your own hands?
The most common type of cartridge mixers is one-dimensional, so further describes the algorithm for replacing the cartridge with a diameter of 35 or 40 mm in the mixer of precisely this type.
It is suitable for both the shower cabin and for a regular washing, because there is usually no difference in their device.
- To independently repair the faucet for water in the bathroom, you first need to block the plumbing racks in the house and merge the water from it that remains in it.
- Then the crane disassembled. It is necessary to remove the decorative plug on the crane to open access to the locking screw. It is not fixed extra, so you should not be afraid that it can be damaged. This can be done with a knife or a flat screwdriver.
- The screw must be loosen a flat screwdriver or hexagon. It depends on the type of screw used in the mixer.
- After that, from the mixer it is necessary to remove the handle. It happens that it is not removed due to the fact that it is bought to the housing of the mixer. In such cases, it can be sprinkled with a WD-40 liquid or just to pour hot water.
- Under the lever there is a decorative spherical nut, which is easily removed by his hands.
- Under it there is another nut, designed to join the cartridge to the mixer body. It is already necessary to unscrew or wrench.
- Then you need to pull the old ceramic cartridge and clean the inside of the mixer where the new one will be installed. For this, a rag is removed dirt, rust, sand and lime deposits.
- The next step is to install a new cartridge. It is important that in the excavation on the mixer housing, the protrusions are performed on the cartridge. To simplify this task, there are special labels on the interchangeable detail. It is necessary to make sure that the removable item is installed tightly to prevent leaks in the future.
- To assemble the crane, you need to repeat all of the above actions in the reverse order: spin first fixing, then decorative nut, install the handle on the mixer, screw the screw and install the decorative plug on it.
- At the end of the work, water is started. The crane is checked for leaks.
The main steps when replacing the ball cartridge are mainly coincided with those described above. However, there is still a difference: after the crane is disassembled, you need to get the ball valve. It is removed for the rod with the help of pliers. Then they inspect the rubber seat of the cartridge for damage to damage and are replaced if necessary. Then the ball itself is checked. If there are defects on it, it is also replaced. Next, you need to clean the cavity in the bowl and install it in place. Rubber gaskets are also replaced, the whole design is assembled in reverse order.
To disassemble a two-mentile shower faucet or bathroom, you will need to unscrew the screw, hidden under the decorative plug on the valve. Next, the crane tap is turned with the key. This is required to determine the layout state. Perhaps enough will only tighten the mount, and the problem will be solved. Otherwise, it is necessary to replace the gaskets and the cartridge. After that, the crane is screwed into place.
Subtleties of repair
It should be borne in mind that in some mixers an additional temperature controller is installed, a mechanical water purification filter or, for example, a motion sensor. In this case, it is better to contact a specialist in the plumbing, because such devices will be much more complicated to disassemble and assemble, without damaging anything. Regardless of the type of device, when it is repaired, it is necessary to act very carefully and carefully, because all its details are very easy to damage. They do not accept coarse mechanical effects.
Cartridges of different manufacturers may differ only in diameter, length of the rod and some details of the appearance. There are no fundamental difference in them, therefore, the algorithm for their replacement will be in all cases the same. The main thing, buying a new cartridge, have an old old hand to make sure that it is suitable for a certain mixer.
There is another option: knowing his model of the mixer, you can find information about what the cartridge is suitable for it, or it will help to determine the consultant in the store. But it should be remembered that it will work only in that situation if we are talking about a mixer of a popular and modern model.