How to make a street washbasin for giving with your own hands - various options. We make a street washbasin for the cottage: simple (and not very) Options Street washbasin for giving with their own hands

County Plastic Bottles

The thing is necessary in the country - a handicraft or a washbasin, which can be hung on the plot. This practical fixture will allow you to slip hands after gardening, wash the tools, rinse vegetables or fruits without entering the house. Such a country room can be made easily from plastic bottles, and there may be many ways, we will look at only some of them.

The most elementary summer cottage of plastic bottles is made as follows:

A large plastic bottle is taken with a lid, then the knife or scissors cut off the bottom. The bottom can be cut off until the end and bend (it will be a place for soap). After that, piercing the silent holes on the sides, through which we draw the lace or wire, and hang the resulting colors.

Alternatively, you can nail the manner with a nail to the holder. Or, if you have holders, consolidate the collar on them, as shown in the photo.

Pour water in the clotheser. When you need to wash your hands, just unscrew the lid slightly.

An option with an inverted plastic bottle:

You can still adapt the clothes in this way:

we take a plastic bottle, we make a heated hole over a candle or a slab of the hole in the lid (there should be a lot), we also do the holes for the lace in the middle of the bottle so that it is easily turned over, and hang it in such a way that it is cap.

When washing hands, simply turn the bottle.

Our country room of a plastic bottle is ready! Make it, as you can see, very simple.

Option more complex and functional:

We take two plastic bottles of the same size. First we designate with one bottle, which will be the washbasin itself. Part of the bottom cut off, but not exactly, but leaving a small ear on the rest of the part (it will be a fastening for our country room).

The second bottle cut out the widest part (closer to the base), then finish it as in the figure. We need to do (closer to the top) several pairs of horizontal cuts, 2-3 cm long (here we will insert toothbrushes). Below will cut the rectangular window (cut through 3 sides and turn aside, so that a tube with toothpaste can fit into this tube). I fix the rectangle on the edges of the stapler.

We put on the second workpiece on the first and get a colors with additional functions. Top to put the inverted dyshko (for soap).

Both in the country area and on a picnic sooner or later, the time is coming when you need to wash your hands, because the elementary rules of hygiene are the same for everyone. But civilization is far away, and you need to solve the problem. For this, the usual plastic eggplant is suitable. It turns out a washbasin of a plastic bottle with your own hands to make it elementary simply, and the instruction here is not alone, but immediately several, choose themselves.

Simplest ways

After conducting small research, we found that the question of how to make a washbasin of a plastic bottle is given a sufficiently large number of our compatriots. Accordingly, there are several options. For simplicity, we broke all the advice on 2 directions.

The first includes the simplest designs that are made in a couple of minutes with a minimum set of tools. The second direction is more suitable for fans of intricate, the original mechanisms of the collected from the priests with their own hands.

Simply nowhere

We decided to start with the simplest way in our opinion.

Each of us taught physics at school, but not everyone applies the knowledge gained in practice, and in vain, because the home-made school on the cottage, working on the basis of the elementary laws of physics, can be created in the literal sense of the word in two minutes.

Initially, an eggplant of any capacity and a hot nail, a small hole or any other sharp item is made in the bottom, only a hole should be really small in the region of 2 - 3 mm.
After that you need to tie a wire or rope to the neck. For it, our unique design on a tree or where it is convenient to be suspended.
In principle, this is all, our aggregate is ready. After that, we can only close the hole made earlier with your finger, filled with water tank, tightly spin the lid and hang.
Since there is no air access from above, there will be no water through the hole. But it is worth we to loosen a lid a little, the air will start entering the container and as it arrives, the water will flow from the hole in the bottom. If you turn the lid again, the process will stop.

Hourglass

In our opinion, this wording is best describing the principle of operation of the next hand washing device.

Important: For such a washbasin, it is best to use standard eggplants with a capacity of one and a half liters, preferably with thick walls.
In extreme cases, you can take 2 liters.
It makes no sense to less, and if you take more, the container will simply break under their own weight.

As in the first case, you can do with a seboard and wire, only the instruction for the manufacture and principle of action changes slightly.
We begin with the fact that there are several holes of the arbitrary diameter in the dump of the covers, water will flow through them.
Further, in the middle of the flasks we make a pass-through hole immediately in both walls and produce a wire through it.
All this fixture is suspended at a convenient place for you. After that, the cover-shower is unscrewed and water is poured to the level of hanging holes, that is, up to half. The lid is delayed and the device is ready for operation.
Agree that all this resembles an hourglass. Turned in one direction, the water flowed. Turned over in the opposite, stopped flowing. The only inconvenience is that the tank is small.

Hole in the lid.

This design is closer to the standard, habitual for all, the Russian Federation. It uses a minimum tool for its manufacture. Also as in the "hourglass", you will need a knife, sewer and pendant wire. The eggplant is taken with a capacity of 1.5 - 2l.

We start with the fact that you cut off the bottom from the bottle, it can later be used as a soap. Water will flow through the holes in the traffic jam, only this time the holes need to be pierced not in the snap plug, but from the side right next to the bottom.

The eggplant is suspended down with a plug and filled. While the tube is tightly pressed, there will be no water to flow. But it is worth it to let it go through the holes will begin to pour water. The inconvenience of this device is that if you check the cap slightly more, it can disrupt it and for a fraction of a second all the water is found.

For those who love to tinker

Important: Unlike the above methods, one shill, knife and wire here can no longer do.
These recipes are more suitable for giving, as in the country to make the Waterman easier than on a picnic, because there is more tools and opportunities.
Similar structures are better made from bottles with a capacity of 5 or more liters.

Before making a washbasin of a 5 liter bottle, spend an audit in the storage room and find out what you have in stock, because the designs can be different. The first device that the folk crafts is offered is the same principle as from plastic or metal.

For a moving rod, you can use a regular nail, but it is better to take some stainless rod. The central hole is made in the lid, which will move rod. There are several small holes around it, through which water will flow.

The valve that will be inside the tank and overlap the water current is made from a conventional rubber or plastic suction cup, such suckers hold soaps on the wall.

This valve, concave part down, is attached to the rod, after which the rod is inserted into the lid and all this screws into an inverted eggmarket with a cut bottom. Next, you can pour water and use.

We all understand that it is necessary to wash your hands, but used to do it in a comfortable environment. On the picnic, and sometimes there are no sink and sewage in the country. Watering the water to each other in hand uncomfortable. Hygienic napkins are also not attacked. So, all the eyes are facing a plastic bottle.

The idea of \u200b\u200bmaking a washbasin with their own hands came to many. We decided to check different options for manufacturing a washbasin of plastic containers in operation. For convenience, various methods broke on those that can be implemented in nature in the absence of tools and more complex, which is convenient to apply in the country.

We leave for nature - you need to put your hands into the water

The easiest colorhouse is obtained if a 5-liter eggmarket with water to flip upside down and consolidate in the tree fork. It is worth a little unscrewed the lid - and watering water. However, the container has to be periodically removed to let air portion or supplement the air.

The situation is improving if there is a hole in the bottom of the bottle, as in the photo below. Now we turn the lid and adjust the flow of water. After using the lid closed.

However, such a wage is difficult to fill with water, and we turned the container. The flow of water can be adjusted by opening and closing the lid. The next photo shows how the water is running out of two holes.

It is better not to repeat this error and make one hole, since when turning off the cover to replenish water, you have to hold two holes on the bottom of the tank.

This method is not working very well with a 5-liter core, as the soft walls of the bottle begged, and water runs away for some time and with a closed lid. We found a bottle with a lid from which you can drink, and decided to use it.

Such a lid opens quickly, but does not regulate the flow of water. The water flows too quickly, and the question is solved only by the selection of the diameter of the hole on the bottom of the tank. Located below, the drinking cover is bad.

We again turned the bottle with a lid up. The result is the same: you need to do very small holes so that the water does not run away quickly.

It is very good if you find a nail or a piece of wire, and it is also possible to split them on fire. In this case, you need to do several holes at the bottom of the bottle cap. The bottom of the container should be cut, but not completely.

Now we collect the wage and tie a twine to the tree with a plug down. Water poured through the "cover" on the bottom of the bottle. The latter closes the tank from the garbage. Cork can be rotated and adjusting the flow of water.

At the cottage for the Hoodyman, we find a syringe and self-tapping screws with a drill

In the country, you can make a washbasin of plastic containers with your own hands according to the standard scheme. As a valve, I used galvanized self-tapping screw. Under the hat planted the suction cup from the old soap mix, which overlaps the water well. On the tip of the self-press screwed another lid so as not to damage the hands.

Water poured into an inverted bottle through a partially sliced \u200b\u200bbottom. Water seeps a bit through the valve, so it is better to pull it down slightly after use.

Most of all I liked the Racket with the use of a 2-5ml medical syringe. The sequence of actions is as follows:

Especially for readers of this article we have developed and manufactured with our own hands the hygienic headset. In addition to the haunted man, it includes soapbox and pockets for toothbrushes and pasta. For its manufacture, another plastic bottle will be required, which should be slightly larger than the diameter of the tank for the collar. In our example, a 2-hike container from the beer is well made on a bottle of Coca-Cola. Master class action sequence Next:

See how the headsets look practical in nature. In such a situation, for sure, you do not have to ask for children to wash your hands many times or brush your teeth.

Particularly lucky can be caught on the eye factory valve for a washbasin of plastic bottles. Buy, Put in the car, useful. Pleasant rest!

For convenience and comfort in country possessions, you can create a washbasin for giving with your own hands. Inexpensive and does not require significant efforts, the device can make life much more pleasant. Even if there is a full-fledged water supply system in a country house, the street colorhouse on the plot allows you to quickly slip hands after work with the ground, fertilizers, weeds.

Types of washbasins

It may seem that the wage for the cottage with his own hands can be made only the simplest design. In fact, even a novice master is capable of creating a comfortable and very beautiful washbasin with the easiest tools. The degree of comfort is determined by the structure of the structure.

On your own choice, you can prefer one of the most common models:

mounted (with clamping nose or crane)
on the rack that can be easily transferred and install anywhere in the plot, even where there is no suitable support,
"Moydodyr" - a design with a table, which contains a container for the collection of wastewater,
heated products.

If you need to choose or without it, then our review will help you with this.

And the characteristics that are popular and inexpensive are presented in another material site.

We also have instructions how to do. Selection of materials and sequence of work.

Plastic Bottle Watercraft

If you think how to make a washbasin in the country with your own hands easily, quickly and simple, the design of a plastic bottle will become the best solution. You can create such a design in a few minutes almost without any expenses. Such a clothesman will be perfectly served by the moment until you build a more advanced structure, and maybe it will be in demand in the future.

The general principle of creating such services the same - plastic bottle suspended and fixed vertically neck down. Fill such a bottle can be through the neck, but for this bottle will have to be removed from the support. If rigid fixation is provided, the capacity can be cut off the bottom. In this case, it is better to provide a washbasin of the top cover (for example, made of cut bottom parts) to prevent dust and garbage from entering water.

Variations usually concern the water supply device.

The simplest washbasin street for giving is a plastic bottle, in the lid of which a hole is made, and a regular nail is placed in it with a blunt edge. The nail cover is inside the bottle, and the diameter of the opening larger the diameter of the nail, but less than the diameter of its cap. Thus, in the free position of the nail hat presses the hole, overlapping the output of the water. If necessary, wash your hands, it is enough to lift it, pressing on the free end of the nail to bottom up. The advantage of the design is its simplicity, however, there are significant disadvantages. For example, the nail constantly rust is constantly in the water. In addition, it is not always convenient to use such a push. The model can perfectly work as a street hauncher for the cottage, but it is difficult to wash the dishes with it because of the inconvenience of the drain part and due to the low capacity.

The collaborator for giving the street mounted from a plastic bottle can have as a drain device the usual "native" cover with a hole in the side. When such a cover is fully screwed, the hole is overlapped with a neck of the bottle. Partially opening the lid, you free up the hole, the water begins to pour out of the washbasin. The inconvenience of using such a design is the complexity of regulating the intensity of water supply. The advantage of the previous option is the simplicity of the device.
A more comfortable street colorhouse for giving with his own hands from a plastic bottle can be done sinking the tank with a small crane. It can be purchased or removed from a faulty technique (washing machine, etc.). Fix the tap on the neck is not difficult with the help of the tape.

Mounted models from canisters

If a constructed summer hauncher at the dacha with his own hands from bottles does not provide family needs even with temporary use, you can install a larger model of plastic or metal canisters, or even a bucket. To do this, cut or knock the hole in which the crane is installed.

If necessary, for better tightness, first in the knocked hole in the canister, the hole is installed, supplying it on both sides by rubber gaskets. The position of the coction is fixed with nuts from the outer and inside of the canister. A crane is installed on a sagon.

For installation is important to ensure the tightness of the joints. If you choose a model from the canister, it should be borne in mind that the volume of the drain will be greater, and therefore, it should be thought to think about the drain.

The following options are possible:

capacity for collecting fluid mounted under the washbasin,
drainage
drainage channel K and PR.

If the water permeable soil in which water easily leaves, you can provide liquids the ability to get absorbed into the ground. In this case, the space under the washbasin is recommended to fall asleep with gravel, rubble or claw for better drainage.

Models on stands

Washbasins on racks are tanks with cranes attached to the frame. The frame has in the lower part of the "legs" entering into the ground. Thus, the handicraft on the rack is fluently moved and installed in any part of the household site. For the simplicity of installation over legs-supports, transverse crossbar is performed - this is a peculiar "pedal". You can quickly and reliably install the design by pressing the foot on the crossbar.

The frame design of the washbasin on the rack should be reliably protected from the impact of humidity, especially its support parts that are immersed in the ground.

The tank with a crane can be purchased or made independently. Please note: the depth of immersion of the legs for reliable stability increases in proportion to the mass of the structure. This is an important factor when choosing a tank material and its volume.

Washbasin with Tumbay

A more solid and convenient country washbasin can be done with a table and own support for bulk tank. Such a model can be installed on the street, on the covered veranda and in the house. For its creation, materials will be required, however, for considerations of savings, you can not purchase them specifically, but to use workflow or residues from construction and installation work in another direction.

The main elements of such a hauncher, called "Moidodir", are a sink (in this capacity, even an old dismantled washing during the repair) and a bulk tank, which can be purchased ready or do it yourself. In the second case, certain skills will be required. If the collaborator is provided for the cottage without heating, the tank can be plastic. If you want to provide maximum comfort and provide "Moidody" with a heating element, it is desirable to choose a metal tank.

The washbasin with a table is a frame design, covered with leaf or panel material. It can use:

plywood,
plastic,
polycarbonate
polymeric material panels,
sheet steel, etc.

In the photo one more version of the cabinet, in the manufacture of which wooden boards were used

For a washbasin frame with a table, wooden bars with a square in cross section are used (square side 50-80 mm) or a corner of steel 25x25 or 40x40 mm.

Works are performed in the following order:

Measurement of the sink and calculation of the dimbs of the cabinet.
Cutting frame material (bar or corner) for specified sizes (8 identical segments for the formation of upper and lower horizontal squares).
Cutting vertical racks (4 bars).
Build (knocking, welding, etc.) frame.

IMPORTANT: Materials unstable to the impact of humidity when installing a washbasin on the street is recommended to be painted or covered with varnish.

Drain of water is organized in the most convenient way.

The easiest way to substitute the bucket for waste collection.
For stationary structures, you can make drain into the sewer or ditch.
With a good penetability of the soil, water can be drained into the soil, pre-falling asleep with drainage material (crushed stone, gravel, etc.) to a height of 25-35 cm.

When the framework of the frame on all walls of the couch, except the frontal, sheets or panels are rigidly fastened. Two or one are arranged in the front (depending on the product dimensions) doors. In the cabinet under the sink, the tank or bucket is placed, where water will be drained.

Above the sink should be installed a frame vertical superstructure on which it will be fixed.

Such a washbasin can be equipped with an additionally tabletop and dryer for dishes made of rails.

Do you want to know, ? Then read our separate article with step-by-step instructions for work.

Watering man heated

Washbasin, in which not only cold, but also hot water is a real luxury for giving. Such constructions are usually installed inpatient because they require electrical connection. According to the design, such a metallic manner for giving can be "Moidody" or model on the rack.

To heal fluid in the tank, you can use a conventional boiler, but experienced masters recommend purchase a special TEN with a thermostat. Please note that the power of the Tan should get out according to the tank. With insufficient power, it will have to wait a long time until the water is warming up, and when it is too large, the likelihood that the water will overheat. In addition, you should select the optimal design and heating mode. If the tank is one and not divided into the chambers, water will be warm to a temperature of about 40 ° C, with a separated tank (one section - for the cold, and the other, with a nonsense, for hot water), the heating temperature should be higher. The tank in this case is not equipped with an ordinary crane, but a mixer.

In the manufacture of the electric collaborator, with its own hands, it is important to take care of the insulation of the currentwater wire, as well as to supply the design of a float level or its more complex analog, as well as, in the absence of a thermostat, a thermometer to control water heating.

Another option how to make a wicker in the country is demonstrated on the video.

In this article we will tell you how to make a washbasin for giving with your own hands, consider various options, as well as show photos and video instructions for creating a street washbasin.

The washbasin must be:

simple;
multifunctional (so that you can not only wash your hands);
convenient.

If there is no washbasin yet on your cottage then, please read this article carefully. In fact, the ways of making a homemade hauncher more than enough.

From plastic bottle

The easiest, budget option. It can be a 1.5-liter bottle or a 5-liter eggplant. First you need to cut down the bottom. Then, with a clamp or aluminum wire, secure on some vertical plane. The role of the dispenser in this case will play the lid itself. We recruit the water into the container, and it will flip with a thin flowing when we cut a lid slightly. It turned out the easiest - and it's easier to nowhere - mounted washbasin. That's all the wisdom of this haunted man.

With crane

This stationary design is more complicated, therefore, it will take at least basic knowledge in the plumbing. It will be fine, if there will be a small 6-liter plastic (made of soft plastic) a bidon with a wide neck or any other suitable capacity in your household. You will have to spend this time to sell accessories for the future washbasin. Read:

sgon;
water faucet;
two rubber gaskets;
two nuts;
two washers.

Performance will not require professional skills. Everything is simple: the hole in the lower part of the bidon is drilled under the camp diameter (the lower, the better). Insert the Sgon myself into the hole to the side where the threads are larger, planted from two sides of the washer, and then pads and clamp nuts from both sides. After that, screw the crane, pre-wound on a slice clockwise linen winding, a wicked special impregnation and everything, washbasin is ready.

It will only be for it to choose a suitable tube or pre-bonded from four wooden bars a rack. Securing the bidon to such a design, pour water. And now you have a more civilized option for a larger volume of liquid in the summer washbasin and moreover with a crane for water supply.

In this simple version of the Hoodyman, you can do without cutting. For example, we take a 10-liter galvanized bucket. We will need:

two rubber gaskets;
nut;
crane brass watershed adhesive;
nozzle on a drill.

The work is simple: at the bottom of the bucket with the help of the nozzle we drill the diameter for a brass crane. Place the laying on it and insert into the finished hole. On the other hand, also insert the gasket and clamp the nut. The upper part of the washbasin is ready.

We will not know that the street washbasin must be equipped with a drain. This may be the usual container where the water or ready-made shell is assembled, with a corrugated tube inserted into the drain (from three meters). With the help of such a tube, water can be rejected simply into the garden and soaked into the ground. Some people plums do not equip at all, and water flows directly to the ground. And so that under his feet was not formed dirty alien, (two buckets are enough). As they say, cheap and angry.

For premises

If we are talking about homemade schools on the street, then it is necessary to mention the washbasins in the room. The inner collaborator is much more complicated in design than its street fellow. It is clear that here you need to take care not only about its functionality, but also about beauty. In other words, he must harmoniously fit into the overall entourage of dacha hard life. Most likely, it will be the most common type of internal washbasins - Moidodyr. How to make this haulage of a tree? We will need 25 × 150 mm boards.

In vertical billets, it is necessary to cut the recesses in advance (depth of 20 mm, width 8 mm). This can be done using a manual millingrer. In horizontal blanks using a conventional wooden hacksaw, spikes are cut according to the wood.

The hacksaw should be sharp and with small teeth. Length of the canvas: 25 -30 cm.

The size of the future washbasin is largely determined by the dimensions of the water tank, which we plan to use for it. It is also important for us to know for sure and the size of the shell, which we will be attached to the Tumba. After everything is cut in size and cut the technological recesses together with spikes, the washbasin is going, like a constructor. However, the connection places will be better consolidated by wood screws.

The top (or side) part of the design has a niche where we should insert the finished water container.

For such a washbasin, a 20-liter galvanized tank is suitable (width: 490 mm, height: 360 mm, thickness: 140 mm)

The bottom of the handicraft stands strengthen the rails (20 × 45 mm) at the same distance from each other. The rear wall of the upper part of Moydodyra is closed with plywood - from 3 mm and fasten with self-drawing. Of course, it is better for such a case to use moisture-resistant fane in the case if the water container will give to flow, but if there is no such - not scary.

As for the door of the cabinet, everything is simple: to frame from four connected small wooden planks from the back of it, we glue the square of 3-millimeter plywood. It remains to embed the lock with a curly handle. All, wooden frame "Moidodyra" is assembled. Now the last touch is grinding, painting the product, and then installing the sink. It turns out very nice.

Washbasin options are quite a lot and all of them are good by themselves. The question is exactly what kind of design you will prefer. Much, of course, depends on the functions that you lay on it. Anyway, the Hoodian / Washbasin is convenient in all respects. And if it is in the country, so more. Therefore, we hope that this article was useful for you.