For people who decide to update the interior by re-gluing wallpaper, information on how to glue non-woven meter wallpaper will come in handy more than ever. Using this particular type of wallpaper for a novice builder is an absolutely unknown occupation, because earlier, in most cases, the walls were pasted with canvases that were standard in width. But in parallel, there was also a release of non-standard, meter-wide wallpaper. Using this particular type of canvases, you will have to completely change the sequence of repairs in the room.
The material for making one-meter canvases is practically no different from ordinary wallpaper, but the width of the finished products significantly saves time and your own efforts for pasting the wall. In our article, we will tell you in detail about the features of the choice of canvases, the preparation of the wall surface and how to properly glue wide wallpapers.
Varieties of meter wallpaper
Most of the wallpaper products produced are manufactured strictly according to a certain standard - 53 cm wide. Products manufactured abroad have a wider range of products, but in most cases, wallpapers have non-standard sizes.
Here are some examples:
- Wallpaper of German and Italian factories has a working width of 70 cm or 106 cm.
- Belgian factories offer wallpapers in rolls of 90 cm, 100 cm or 140 cm.
- French manufacturers sell their products in the following established sizes - 90 or 70 centimeters.
Advantages and disadvantages of meter wallpaper
Before you buy your favorite custom wallpaper rolls, you should familiarize yourself with the advantages and disadvantages of this finishing material.
Advantages of wide wallpapers:
- In most cases, wide canvases are produced on a non-woven base, which greatly simplifies the pasting process. To do this, simply apply the adhesive mixture to the wall surface and attach the prepared strip.
Important! Before gluing wallpaper on a non-woven basis, one meter in width, you must first level the surface of the wall with a starting and finishing putty.
- A huge assortment of wallpapers is presented not only with a non-woven base, on the shelves you can choose wallpaper on a paper base of various colors with a pattern that suits your interior.
- When pasting walls in wide stripes, the number of seams is reduced.
Important! Walls decorated with this type of wallpaper are called seamless.
- When using meter-long canvases on large areas, the joints between the stripes are almost invisible.
- The process of pasting a wall is greatly simplified due to fewer stripes.
Important! Agree that it will take less time to cut 5 strips and apply them to the wall than doing the same process with only 9 pieces.
- The cost of purchasing the required material is reduced.
Important! The cost of one wide roll is cheaper than two standard rolls.
Disadvantages of wide wallpapers
As such, these products do not have any disadvantages, but when working with them there are slight difficulties:
- Before gluing wide non-woven wallpaper to the surface, it must first be prepared, visible irregularities, cracks and other defects must be removed.
Important! If you start pasting without preparation, you will not be able to achieve perfect joining of the strips with each other, which will ultimately affect the quality of the wall repair.
- Due to the large width of one roll, you may have a situation when a couple of centimeters of wallpaper is not enough to paste over the entire room. As a result, you have to buy a whole wide roll, which leads to additional costs and a large amount of leftovers.
- Having some experience in carrying out repairs, wallpaper that is standard in width can be glued to the wall yourself. In the case of meter wallpaper, it is better to find an assistant.
If, after going to the mall, you have opted for canvases of non-standard width, then you just need to know how you stick wide wallpaper on the wall with your own hands.
Surface preparation for pasting
If you are interested in the question of how to properly glue meter-long wallpaper, then, first of all, you should familiarize yourself with the principles of preparing the surface on which you plan to apply wallpaper.
Important! The preparatory process and the pasting of the walls should be started when the finishing of the ceiling has not yet been completed.
So, what actions are simply necessary to successfully perform pasting with meter-long wallpaper?
- Remove all installed switches and outlets. Seal the holes after dismantling with special adhesive tape.
Important! The use of a special tape will save time after the completion of the repair - it is more easily and quickly removed.
- Remove from the wall all screws, screws, dowels, with which shelves, paintings and other hanging objects were attached.
- Remove the old wall covering without the slightest residue.
- In the case of too uneven walls, it is necessary to process it with a dry mixture to level the surfaces or plasterboard cladding for additional insulation of the room from the inside.
Important! If the walls are affected by fungus or mold, then gluing wallpaper on such a surface is strictly prohibited. In this case, first of all, you should remove the affected areas with a special tool.
- After treating the walls with a primer, set a special temperature regime in the room, make sure that there are no drafts or overheating of the air.
- Before gluing wide wallpapers, a primer is applied to even walls, with its help microcracks and microscopic pores on the surface are eliminated.
Important! Treated walls will prevent the adhesive from absorbing too much into the surface, which will reduce the consumption of building materials and ensure strong adhesion of the wallpaper to the wall.
- If the installation of foam or other type of curbs is envisaged, their installation is carried out before pasting the walls with wallpaper.
Required tools and materials
In order to carry out high-quality pasting of walls, prepare all the necessary equipment in advance. To do this, you will need:
- Special wide brush for applying adhesive to the surface of the wallpaper;
- Rubber roller to smooth out creases and eliminate air bubbles;
- A simple marking pencil;
- Scissors or utility knife;
- Cotton rags to remove excess glue;
- Plumb line.
Important! When buying a product at a specialized point of sale, be sure to check the compatibility of the adhesive with the base from which your wallpaper is made.
How to glue meter wallpaper?
Non-standard type wallpapers are divided into the following classes:
Although in most cases glue is applied to the surface of the walls, check the instructions to be sure, because some canvases also need to be treated with glue. Next, we will consider in detail how to glue wide wallpapers on a non-woven base so that the joints are not visible on the surface.
Important! The work, as in the case of standard canvases, starts from the window and moves in the direction of the incident light. When joining the canvas, it is imperative that the drawing or pattern is accurately combined.
The sequence of pasting walls with wide wallpaper:
- Before starting all work, measure the length of the wall in order to calculate the required number of whole strips.
- Make a layout for the location of the first strip of wallpaper - the layout is drawn from the window into the interior of the room.
- At a distance of 105 cm, draw a line from the ceiling to the floor with a pencil and a plumb line, in case of a blockage of the corner, leave 1-2 centimeters.
- Pay special attention to wallpapering in the corners of the room. If you do not have a certain experience, it is better to leave a small gap, it can be blocked with a canvas on the opposite wall, so that an unaesthetic gap does not form.
- Next, cut the required number of whole strips, taking into account a small allowance along the length.
- Thoroughly coat the wall with adhesive, going beyond the pencil line.
- Call your partner for repairs:
- One person should hold the wallpaper by the top edge while standing on a ladder or high table and apply the canvas to the ceiling cut line, which is marked with a pencil or foam border.
- The second participant in the process must adjust the coincidence of the canvas with the vertical marking line.
- With a rubber roller, moving from the center to the edges, squeeze out the formed air bubbles, remove excess glue with a cotton rag.
Important! You should not smooth the wallpaper horizontally, then an ugly gap will form during the drying process, since the wallpaper shrinks to its original state.
- Place all subsequent canvases close to the previous one, without gaps and overlaps.
Important! It is not always possible to stick an even number of whole strips on one wall, the latter often has to be cut vertically. Glue the canvas on the other wall exactly from the corner, slightly overlapping it. Trim the excess wallpaper with a sharp office knife only after the walls are completely dry.
Pasting inconvenient places
In the process of pasting walls with non-standard wallpaper, it becomes much more difficult to apply paintings in difficult places - corners, behind the radiator, above door and window openings.
Important! When finishing the ceiling, on the contrary, pasting will take less time. Firstly, you will need several times fewer stripes, and secondly, you will have an assistant, since it is quite difficult for one person to glue wide wallpapers.
Here's how to make it easier for yourself:
- To glue the surface behind the battery, cut the strip lengthwise into several pieces.
- It is quite difficult to combine a drawing in these places; this will require some experience. However, non-woven wallpaper has one positive feature: it can be moved within 10 minutes, thus, it will not be difficult to trim the pattern.
Important! This option is possible in the case of using an adhesive that does not include components that contribute to the speedy hardening of the glue.
- A peculiarity of wide wallpapers should be noted such a nuance: in a rolled roll, they look a little different than they look after being applied to the surface. Consider this fact when choosing a picture.
- To create an original room design, select decorative elements from the same collection as your chosen wallpaper.
- Pay attention to the quality certificate. Make sure of the quality of the selected product.
- If the first time it was not possible to evenly apply the wallpaper to the surface, you can remove the strip, treat the wall with glue and repeat the procedure again.
- It is recommended to open a window or doors in a room being repaired only a day after the work has been carried out.
- To create an original design indoors, you can use several types of canvases at the same time in shade and texture. Thus, you can hide flaws or emphasize the features of your room.
- Consider when choosing canvases that the horizontal arrangement of the pattern visually reduces the height in the room, and vertical lines and patterns expand the space.
Video
Now you know how to glue 1 meter wallpaper in room. Applying the tips from the article in practice, you can easily decorate the walls of the apartment with non-standard wallpaper. Such canvases will help to decorate your room, emphasize the peculiarity of the interior and create a unique effect of a seamless surface. A wide range of finished products allows you to choose one meter long wallpaper of any color, shade, texture. However, be sure to pay attention to the characteristics regarding their pasting on the wall, and the quality of the product.
Recently, in stores of building materials, more and more often you can find wallpaper of a meter wide, that is, a non-standard size familiar to our people. Why are these wallpapers so good that in a very short period of time they were able to win the hearts of the general public, how to glue them and should they give their preferences?
Instruction.
1. wide wallpapers, undoubtedly, have enough advantages over the usual thin types. So, meter-long wallpaper simplifies pasting work, reduces the number of seams, which often spoil the overall appearance of the room, and also reduce the cost of purchasing such material for wall decoration, since one roll of meter-long wallpaper costs a little lower than two similar small ones.
2.Prepare wallpaper, special non-woven wallpaper glue, building water level, pencil, tape measure, glue roller and bucket, plastic spatula, soft bristle brush, knife, plastic wrap and edging roller.
3. prepare the room. To do this, you must completely remove the previous coating, level the walls if necessary, remove all sockets and switches, insulate the wires. Mark the room. The markup should be started from the corner of the room, as the wallpaper will be overlapped there. Set aside one meter to either side of the corner and make a vertical mark with a pencil and a level, approximately at the height of your height. Make these marks every 1.06 m (tube width), marking the exact distance with a tape measure.
4. Spread the film on the floor of the room so that the wallpaper does not get dirty and glue does not get on the floor. Determine the height of the wall by measuring it with a tape measure. Roll the tubing face down on the film. Mark your length (wall height) 10 cm.
5.Fold the roll and return to the starting point with it so that, by cutting off the length, you end up with two strips of wallpaper. Slide your finger along the fold to make it smoother and more precise.
6. Cut the folds with a prepared, well-sharpened knife. In this way, prepare strips of wallpaper for the entire room.
7. Dilute wallpaper glue according to the instructions and let it stand in a bucket until it swells completely. Dip the roller in the glue and spread on the wall the area for the first panel (first strip. Take the first strip of wallpaper and attach it to the wall. It is important to know that pasting the strip starts from the top (from the ceiling) and stretches downward).
8. Take a brush and smooth the entire length of the fabric from the middle to the edges. Do the same with a plastic spatula. The canvas should fit snugly against the wall and be free of bubbles. Cut off the floor stock, if any. In this case, take into account the width of the skirting board, which will subsequently be fixed.
9.Glue the second strip in the same way. When pasting the corner, the wall should be abundantly coated with glue. Here, two strips of wallpaper are located on top of each other, that is, there is an overlap pasting. In this case, the wallpaper is tightly pressed with a spatula and the corner is cut, after which the seams are exactly joined. Take a roller and gently roll the seams with it. Carry out the same actions with other canvases, joining them with each other along the outlined lines.
Advice 2: how to glue non-woven wallpaper.
Non-woven wallpaper is sold either with a ready-made pattern applied, or is intended for further painting. When choosing rolls with a thick texture, you can mask minor flaws left during the repair of the walls. Thus, if you are a fan of frequently changing the color scheme of the surrounding interior, choose wallpaper that can be repainted 7-10 times. The non-woven base easily glides on the wall and allows you to conveniently carry out wall pasting alone.
You will need.
- Non-woven wallpaper;
- Adhesive for non-woven wallpaper;
- Building level;.
- Pencil;.
- Roulette;
- A roller for glue;
- Bucket for glue;
- Polyethylene film;.
- Plastic spatula for wallpaper;
- Soft brush.
- Knife;.
- Metal spatula;
- Plastic mesh in a bucket for glue;
- Roller for rolling the edge.
Instruction.
1.Count how many wallpapers you need. Measure the height and width of the room separately on each wall. Draw the plan on a piece of paper. This leaflet will come in handy when choosing wallpaper.
2. When buying wallpaper, pay attention that the batch number on the label in rolls is the same. Look at the other pictograms, it may or may not need to be adjusted. Do not forget to add another 10-15 cm to each panel in reserve. Get out a piece of paper with a plan of the room and count how many selected rolls you need. 3. Prepare the room for wallpapering. The walls must be pre-leveled. Switches unscrewed and sockets. Insulate the wires to prevent liquid from seeping into electrical boxes. Treat the walls with soil and dry.
4. mark the walls. Non-woven wallpaper has a good edge and is glued end-to-end. It is most convenient to start marking from a corner. There, the panels will overlap, so that they can then be processed correctly. Roll width 1, 06 m. Set aside 1 m on both sides of the corner. Using a level and a pencil, draw a vertical line at the height of your height.
5. Measure with a tape measure from the drawn line in both directions by 1, 06 m, the size of the next canvas. Thus, outline all the walls in the room. Write the width of the panels on the wall with a pencil. You will immediately see where to glue the prepared wallpaper.
6. Spread plastic wrap on the floor. Roll the wallpaper roll over it, face down. At this point, you must remember whether the wallpaper needs a pattern fit. Consider this when cutting panels. In the event that a fit is not needed, then measure the height of the room with a tape measure and add 10 cm. Fold the roll onto the rolled part so that the edges coincide, then the fold will be even.
7. Run your hand over the fold and cut with a paint knife. Prepare wallpaper for the whole room. Roll the sheets into loose rolls so that the design is inside.
8. Dilute the wallpaper glue in a bucket according to the instructions. Pour water into the bucket and add glue in a thin stream. Stir constantly to avoid clumping. Let the glue stand, it should swell.
9. Insert a plastic mesh into the bucket to remove excess glue. Dip the roller into a bucket, run it along the net and smear the wall for one piece of cloth. 10.Glue the wallpaper on top. Grasp the edge of the canvas with your hands and attach it to the wall. Run the roll down, smoothing the wallpaper with a brush from the middle to the edges. You can smooth it right away with a plastic spatula, just do it with care so as not to tear off the drawing. The canvas should fit snugly against the wall without folds or bubbles.
11. Roll a seam roller on all seams of the wallpaper. 12. When gluing the corner, the wall should be generously coated with glue. Two panels are overlapped. Press down on both blades with a trowel and cut through them in the corner along their entire length. Then the joints of the wallpaper will match. 13. Cut off the floor stock. Consider the width of the future skirting board, which should hide the edge of the wallpaper. 14.Glue the top of the wallpaper with a fillet or border of the desired thickness.
More informative articles on good apartment renovation
Non-woven wallpaper is one of the most popular and versatile wall decoration materials. This is due to their wide range and excellent quality.
It should be remembered that non-woven wallpaper masks the imperfections of the walls.
In addition, meter-long wallpaper is much faster to glue than wallpaper of standard width. Non-woven wallpaper is available on a non-woven basis or completely made of non-woven fabric.
Characteristics of non-woven wallpaper
The composition of this material is fabric and paper fibers, impregnated with special binders.
Non-woven fabric is durable and easy to use. It has long been used in the textile industry: it is added to fabric to give strength and volume.
These meter wallpapers are presented in a wide range of colors, textures and densities. quick and easy. They do not tear, stretch, or shrink after glue is applied. This finishing material perfectly masks small defects and cracks on the walls.
Non-woven wallpaper does not wear out and retain its original beautiful appearance for a very long time. They lend themselves well to coloring without losing their relief structure and quality.
The upper part of the wallpaper is a vinyl covering. This gives the material strength and lightness, which cannot be said about paper wallpaper.
The variety of textures of this finishing material allows you to imitate any kind of surface: plaster, wood, marble, stone.
Multilayer interlining allows you to create the illusion of a three-dimensional image. Thanks to such special effects, the room can be visually enlarged.
How to glue non-woven wallpaper? This material is so versatile that it can be applied to any surface: concrete panels, drywall, chipboard sheets, plaster, wood, paper.
But if the meter-long wallpaper is thin enough, then it is preferable to glue them on a flat and smooth surface. If it is a concrete base, then it is necessary to putty all cracks and irregularities. If the wallpaper is planned in light colors, then the base must be of a single color.
For example, if the wallpaper will be glued to drywall, then you must first putty the joints of the sheets, and then apply one layer of putty to the entire surface so that it becomes homogeneous.
Maintenance of the non-woven coating is very simple: any dirt can be wiped off with a damp cloth using a cleaning solution. In the case of paper wallpaper, this cannot be done: the dirty paper covering can only be replaced.
Back to the table of contents
Surface preparation for pasting with meter wallpaper
To work you will need the following tools:
- laser level;
- tape measure and pencil;
- long pile roller;
- plastic and metal spatulas;
- assembly knife;
- two containers: for glue and water;
- soft sponge.
The preparation of the walls begins with the dismantling of the old coating. It is good to remove old paper wallpaper with a spatula, after wetting the walls and leaving them for a few minutes.
If the walls are painted, then you have to work hard: old paint is difficult to peel off with a spatula and sandpaper. The best option for this would be to use a drill with an attachment. A metal brush is suitable as a nozzle.
When the base under the wallpaper is cleaned, it must be primed. This is done for good adhesion of the finishing material to the walls.
Using a level on the walls, mark vertical lines in increments of one meter. But the width of these wallpapers is slightly larger, 1.06 m. This margin is needed for possible deformation, shrinkage or correction of the edges.
Before pasting, the wallpaper must be cut onto all walls at once. If the wallpaper is with a displaced pattern, then the material must obviously be bought with a margin. If the colors are uniform, then there will be no difficulties in matching the pattern.
If the preliminary repair was carried out according to all the rules: the walls and the floor, the ceiling are aligned, then all strips of wallpaper will be the same length.
If cosmetic repairs were made without leveling the surfaces, then, most likely, the height of the walls in different areas will be different. This means that the lengths of the stripes will also be different.
Cut the roll on a clean floor with the wallpaper facing down. Measure the required length of the strip, make a mark and cut it off with a mounting knife.
When combining drawings, the first strip should be applied to the rolled roll in the place where the image joint will be. The seam of the pattern will be the beginning of the length of the second strip. In this case, some of the wallpaper goes to waste. However, large pieces of material can be useful for gluing in irrelevant places: behind the battery, cornice, curtain.
The glue should be for non-woven wallpaper. Its preparation technology is simple. According to the instructions, the dry composition is poured into the water in a thin stream until the required consistency is obtained. Having removed the lumps from the composition, you can start pasting.
