A plastered facade is an excellent solution for protecting walls from moisture, giving them an aesthetic appearance. The products of the Russian company Bolars have proven themselves very well. has a number of advantages and is in demand in the finishing works market.
Facade Plaster Bolars what is it
Effective composition for plastering facades. Contains special modifiers to prevent the appearance of microcracks on the surface. Imported polymer additives give the material excellent performance properties.
This coverage:
- Frost-resistant;
- Not afraid of exposure to moisture, natural factors;
- Lays down in an even layer;
- Allows the surface to "breathe";
- Plastering work can be performed manually and mechanically;
- Long-lasting, well-proven throughout the entire service life;
- Not subject to shrinkage;
- High adhesion;
- Dries quickly enough.
Specifications
Application area
Facade plaster BOLARS is used for high quality coating during external and internal finishing works.
The composition performed well in rooms with normal and high humidity. The reason is admissible:
- Brick.
- Stone.
- Aerated concrete.
- Concrete.
Facade mortar preparation
When the BOLARS composition is used, it is poured into a hopper, and then the mixture is prepared in a mechanized way strictly according to the instructions for the plastering machine.
The viscosity of the solution is selected taking into account the characteristics of a particular type of unit.
If the solution is prepared by hand, the steps are as follows:
- A kilogram of dry plaster is diluted with clean water in the amount of 0.4 l - 0.42 l.
- Water consumption per 30 kg bag - 12 liters.
- Little by little, add the mixture to the water and gradually stir.
- Mix the mass thoroughly with a drill with a special attachment or manually.
- After 5-10 minutes, the aged solution is stirred a second time.
- Can be plastered.
The solution is in working order for no more than 3-4 hours.
Preparation of the base
- Check the strength of the base. The flaking parts are removed.
- They carry out works on waterproofing and installation of drainage systems, utilities.
- They clean the surface from dirt, dust, stains that reduce adhesion to the substrate.
- Process the facade with a suitable type of soil.
- Facade surfaces can be plastered after the primer has completely dried.
Application of facade plaster mixture
Video - :
Please note: the company produces various types of primers. The choice depends on the absorption capacity of the substrate:
- BOLARS Firming - for normal water absorption.
- BOLARS Deep Penetration - for highly absorbent surfaces.
- BOLARS facade Anti-mold with fungicidal properties - in case of mold infestation.
Precautionary measures
- Operations are performed with rubber gloves.
- Make sure that dry powder and solution do not get into the eyes.
- If the solution gets on the cornea of the eye, rinse the eyes quickly with plenty of water.
- In case of deterioration of the condition, the appearance of discomfort in the eye, consult a doctor.
- Keep bags and prepared solution out of the reach of children.
Front Bolars Price
A craft bag weighing 25 kg costs 250 rubles. It is enough for 18 sq. m, if the layer thickness is only 1mm. It is not difficult to calculate the cost of material when changing the thickness of the coating.
25 kg. Scope of application Frost-resistant, weather-resistant plaster of increased strength BOLARS Facade is intended for finishing the facades of buildings and premises with any level of humidity. Has a high vapor permeability, which makes it possible to "breathe" the surface. Easily leveled, does not crack, does not form shrinkage cracks. It is made on a cement-sand base using highly effective modifying additives. For work at t up to -10 0C, a winter, frost-resistant version is produced. Recommended substrates Applied manually or with the help of continuously working on all concrete, foam and aerated concrete blocks, gas silicate, brick, masonry, cement-sand plasters. Substrate preparation The subfloor must be sound and have sufficient load-bearing capacity. Peeling, fragile areas must be removed. Before starting work, the surfaces must be dedusted and cleaned of all types of contaminants that reduce the adhesion of finishing materials. Prior to the commencement of facade plastering, external waterproofing and drainage engineering systems must be installed. Facade finishing with faulty storm water systems is not allowed. It is recommended to treat bases with normal water absorption with BOLARS Strengthening primer. Highly absorbent substrates must be treated with BOLARS Deep Penetration primer. The areas affected by mold fungi are treated with the fungicidal composition BOLARS Anti-Mold before applying the primer. Plastering of surfaces is carried out after the soil has completely dried. Mortar preparation In mechanized application, the mixture is prepared in machines for mixing and supplying plaster mortar. Pour the dry mixture into the hopper of the plastering station. Adjust the water supply (the amount of water is determined by the type of plastering machine) to match the required mortar consistency. To prepare the mortar mixture for manual application, it is necessary to take an accurately measured amount of clean tap water at room temperature (for 1 kg of dry 0.20-0.23 liters of water, for 1 bag of 25 kg - 5.0-5.75 liters of water). Mixing is carried out in a mechanized way (with a drill with a nozzle), evenly pouring the dry mixture into water until a homogeneous pasty mass is obtained. Let the solution stand for 3-5 minutes, then stir again and it is ready for use. The finished solution is in working order for at least 3 hours. Execution of work with the prepared solution of BOLARS plaster. Treat the finished facade surface by machine spraying or apply with a trowel, trowel or spatula on the base with a layer of 2 to 20 mm, then level it with a rule or a float. When plastering brick walls and surfaces made of gas silicate blocks, it is recommended to use a facade fiberglass mesh. To obtain an even, smooth layer, after the mixture begins to set on the wall, smooth the surface with a metal spatula. Application in two layers is allowed (total application thickness up to 30 mm). To do this, comb the first layer that has not yet hardened with a plaster comb and dry completely. Before applying the next layer, the surface must be treated with BOLARS Strengthening primer. For final leveling, it is recommended to use materials of the BOLARS filler group, depending on the type of substrate and working conditions. Consumption Average consumption for a layer thickness of 10 mm 13-14 kg / m². Bag 25 kg - 1.7-1.8 m² with a layer thickness of 10 mm. Working conditions The indicated time characteristics are valid at an ambient temperature of + 20 ° С, relative air humidity 60%, at other temperature and humidity conditions they may change. When carrying out work and during the next 3 days, the temperature of the air and the base should be in the range from + 5 ° С to + 30 ° С. The temperature of the mortar mixture during the work must be at least + 5 ° С. It is not allowed to apply plaster in rainy, windy weather, in the presence of surface condensation. In the process of curing, the plaster should be protected from drying out, drafts and direct sunlight. Limitations In order to avoid a decrease in the strength characteristics of the plaster, it is prohibited to overflow water in excess of the standards specified by the manufacturer, and to additionally introduce other components into the ready-made mortar mixture. When the solution thickens in the working container, it is mixed again without adding water (within the pot life of the solution). Ensure adequate ventilation during interior work. Forced drying of the plaster layer with the help of. Precautions In case of contact with eyes, rinse with plenty of water. It is recommended to carry out work in rubber gloves. PROTECT FROM CHILDREN!
Bolars front plaster (gray) - sale in Moscow. You can buy goods "Bolars plaster front (gray)" from us at the price of 253 rubles. In order to buy this product, click on the "Show phone number" button.
What plaster can be applied down to -10 ° C? Of course, this is Bolars frost-resistant facade plaster - a unique dry mix made on a cement-sand base with the addition of polymer modifiers. A well thought-out composition and precise dosage of components endow this building material with many advantages.
What are the advantages of Bolars frost-resistant facade plaster?
- The ability to apply at subzero air temperatures allows you to speed up the time of work.
- Improved strength, endurance and wear resistance values guarantee durability.
- Frost resistance - the ability to withstand multiple freeze-thaw cycles without losing characteristics.
- Suitable for external and internal plastering work.
- The ability to adjust the layer thickness depending on the need.
- High vapor permeability rates contribute to the natural circulation of air masses and allow you to create a favorable microclimate in the house. Ease of use - it is enough to dilute the dry mixture with water according to the instructions and mix it well, and everyone can cope with the application of a plastic composition that is easily leveled.
- Crack resistance - resistance to the appearance of shrinkage cracks during operation.
Important information on the use of Bolars frost-resistant facade plaster
The material is suitable for finishing works on the facades of buildings and indoors - regardless of the level of humidity. It is applied manually with a trowel or trowel on concrete, foam concrete, stone, gas silicate, brick or aerated concrete substrates, as well as on substrates covered with a plaster mixture.
Application area:
Solution preparation:
Consumption:
Precautionary measures:
Packaging and storage:
TU 5745-031-56852407-09
Specifications:
BOLARS Facade (gray)
|
Name |
Meaning |
|
Drying time |
|
|
The density of the mortar mixture |
1.7-1.8 g / cc cm |
|
0.21-0.23 l / kg |
|
|
Average density |
1550-1650 kg / cubic meter m |
|
Applied layer thickness |
|
|
not less than 4 kg / sq. cm |
|
|
Compressive strength |
100 kg / sq. Cm |
|
Work temperature |
|
|
Operating temperature |
|
|
Frost resistance |
not less than 50 cycles |
|
Name |
Meaning |
|
Drying time |
|
|
The density of the mortar mixture |
1.7-1.8 g / cc cm |
|
Amount of water per 1 kg of dry mix |
0.21-0.23 l / kg |
|
Average density |
1550-1650 kg / cubic meter m |
|
Applied layer thickness |
|
|
not less than 4 kg / sq. cm |
|
|
Compressive strength |
100 kg / sq. Cm |
|
Work temperature |
|
|
Operating temperature |
|
|
Frost resistance |
not less than 50 cycles |
|
Time of solution availability for work |
not less than 3 hours (30 min at - 10 ° С) |
|
13-14 kg / sq.m (with a layer thickness of 10 mm) |
BOLARS Facade (gray) - weather-resistant, frost-resistant, waterproof plaster on a cement-sand base with the use of highly effective imported polymer additives. Does not shrink and forms a flat surface. Contains modifiers that prevent the formation of microcracks, as well as waterproof additives that determine the durability of the coating during operation. Layer thickness 2-20 mm. It is used for both indoor and outdoor work.
Application area:
BOLARS Facade (gray) is used for high-quality plastering of facades of buildings and interiors with normal and high humidity. It is applied on concrete, aerated concrete, brick, stone surfaces.
Solution preparation:
Dilute 1 kg of dry mixture in 0.21-0.23 liters of clean tap water (for 1 bag of 25 kg - 4.5 - 5.0 liters of water). Mixing is carried out manually or mechanically (with a drill with a nozzle), evenly pouring the dry mixture into water until a homogeneous pasty mass is obtained. Let the solution stand for 5 minutes, after which it is necessary to stir it again and the solution is ready for use. The consistency is in working order for at least 3 hours.
Substrate preparation, application:
Before starting work, the surface must be hard, free of old paint, dust, grease, oil contamination. It is recommended to treat the surface with BOLARS Deep Penetration Primer.
The plaster is applied to the base with a layer of 2 to 20 mm and leveled with a rule or a trowel. If necessary, the surface can be sanded after drying. Work should be carried out at an air temperature of + 5 ° C to + 30 ° C. Drying time 24 hours. The initial strength is reached after 3 days.
Consumption:
13-14 kg / m2 with a layer thickness of 10 mm. Bag 25 kg per 18 m2 (with a layer thickness of 1 mm).
Precautionary measures:
Avoid contact with eyes. If the solution gets into the eyes, it is necessary to urgently rinse them with copious amounts of water. It is recommended to wear rubber gloves.
Packaging and storage:
The plaster is supplied in 25 kg kraft bags. The guaranteed shelf life in a dry place and undamaged original packaging is 12 months from the date of manufacture.
Specifications:
| Name |
Meaning |
| Color |
Grey |
| Drying time |
24 hours |
| The density of the mortar mixture |
1.7-1.8 g / cubic meter |
| Amount of water per 1 kg of dry mix |
0.21-0.23 l / kg |
| Bulk density of dry mix |
1550-1650 kg / cubic meter |
| Applied layer thickness |
2-20 mm |
| Adhesion |
not less than 4 kg / sq. cm |
| Compressive strength |
100 kg / sq. Cm |
| Work temperature |
+ 5 ° C + 30 ° C |
| Operating temperature |
-40 ° C + 60 ° C |
| Frost resistance |
not less than 50 cycles |
| Time of solution availability for work |
not less than 3 hours (30 min at - 10 ° С) |
| Consumption kg / sq.m |
13-14 kg / sq.m (with a layer thickness of 10 mm) |