Washbasin for cottages - Beautiful options for the landscape! (76 photos). Straw house How to make water tank from tin

People, plants, animals need water. Without it, they cannot develop and exist. And therefore it is important to have its stock on the site. Of course, almost everywhere there are water pipes, wells, wells. But there are circumstances when water disappears. It happens most often in roast, dry summer. And then all your works embedded in flowers, vegetables, fruit trees and shrubs will disappear. It hurts will observe how your plants dry out.

To avoid such sad situations, it is recommended to install a storage tank for water on the site.

According to the manufacturer, they are:

• metal;
• plastic.

By the manufacturer's method to be done on:

• industrial;
• homemade.

Depending on what water will be used, choose which material should be made metal container.

If the water is drinking, for cooking, washing, then the water tank must be made of high-quality, stainless, guest steel. In such a tank there should be a ventilated hole with a tightly closing lid. It is not bad to install a protective grid on this hole. A water tap is cut into the stainless steel tank.

Twice a year it must be washed with disinfectants so that the quality of drinking water does not deteriorate. Therefore, in the side part there is a hatch through which it is possible to wash a stainless steel barrel.

If you use water for technical needs:

• glaze;
• household goal;
• rainwater collection

you can purchase a tank of any metal.

In order not to increase the flow of drinking water, it is best to install a capacity for collecting rainwater in the country. This can be both a simple fifty liter metal barrel and special cumulative tanks with filters for water purification.

And if the barrel is inexpensive, besides, you can use the past, the main thing is that chemicals were not stored there, then special capacity for rainwater collection is quite expensive. True, the water collected in them can be used for washing, and for watering. But in barrels you can leave water for the winter.

Plastic water tank

These containers are the most popular. The advantages of these tanks:

• cheaper than similar stainless steel;
• a large selection of various volumes;
• tightness;
• do not require additional care (painting, primer);
• do not rust;
• long service life;
• not afraid of temperature drops;
• hold thirty-perdus frosts.

Plastic container can be performed both from food plastic and from technical.

Plastic food barrels are made of high-strength, frost-resistant plastic. It does not miss ultraviolet rays, so drinking water does not deteriorate in them for a long time.

Most of these barrels are equipped with threaded holes with a plug, the diameter of these holes allows you to install in the tap containers.

Each plastic container has a quality passport.

Plastic containers can be vertical and horizontal.

Evils are in great demand that willingly acquire in the country. They are made of polymeric materials, for greater stability, the cube is placed in a metal incarnation. From above, he has a neck, and at the bottom of the drain crane.

Cubic tanks were widely used in personal farm. They can be used as a cumulative capacity for:

• glaze;
• soul;
• household needs.

It is worth mentioning that the Eurocups are used to transport various liquids, it is impossible to use them as containers for drinking water.

If you have enough money, you can buy a water-made container in the cottage.

But, spending a little time, you can make a tank for water with your own hands, and it will not be worse than factory.

How to construct the container yourself

It is very simply done with your own hands an unusual accumulative tank for water from old tractor tires. To do this, you just have to purchase a large-diameter tires and set on your site.

Capacity can be easily installed with your own hands, for this:

1. A place where the container will be well aligned.
2. Tire cut the top inner part.
3. Install the tire on the prepared surface.
4. We take three pieces of sand, one part of the cement, weaving with water to the state of thick sour cream. All mix well.
5. The bottom of the tires in the resulting solutions, align the surface.
6. We cover the tire of the cellophan so that the water does not get in case of rain. We are waiting for a week until the solution freezes.
7. Remove the film and fill the tank with water.

Water that will be stored here is of course unsuitable for drinking, washing. But it will be quickly heated, and it will be possible to water the plants in the greenhouse. In addition, the container will serve as an excellent rainwater drive. The advantage of the capacity is reliability and durability.

Such tanks are suitable as a spare option for a small volume of water. If you need a large volume, then you should make accumulative tanks more solid.

For the manufacture of a container, accommodating 7 m3 of water, you will need:

• three bars long three meters;
• sixteen bricks wrapped with polyethylene for waterproofing;

• ten boards with a length of at least 3.5 meters and a thickness of 0.5 centimeters;
• six plates of OSP 2.5x1.25 meters;
• geotextile insulation;
• polyethylene dense film of black.
• saws.

Production Stages:

1. On the perimeter of the leveling platform, we declare bricks at the same distance.
2. We laid three bricks on bricks.
3. Fresh self-stakes to Brusa five boards.
4. On top of self-drawing attach 2 OSP plates.
5. We make a frame from the boards, fasten it to the base.
6. On frame screwing the remaining sheets of OSP.
7. Tighten the capacitance from the inside by geoticstyle, attached from above with brackets.
8. Then we lay the film, freely hanging over the edges of the box.
9. Fill the container with water.
10. For reliability, secure a film with an outdoor side stapler.
11. Top of the tank nail two black boards.

The advantages of such a capacity:

• low cost;
• just do it yourself;
• easy to disassemble, transfer to another place.

True, a pump is needed to use such a container, and water will not be drinking.

On a hot summer day after work in the garden, I want to take a warm shower. But in order for water to be hot, it is necessary to warm it. You can buy an electric heater to the cottage, but it is not economical.

It is easier to establish a cumulative container in which water will be heated at the expense of the sun. Such a container can serve any barrel - galvanized, stainless steel or metal, plastic.

To do this, it is enough to install a container at a height and fill it with water.

The easiest way to install plastic containers.

Stainless steel capacity will not rust, the water in it will not bloom, it will be drinking. But stainless steel products are expensive.

An alternative can be a galvanized barrel, it is, of course, not so durable, but if the galvanized will not be broken, it will not rust either.

The most economical option is a metal tank for water, but it must be painted to protect against corrosion.

Urban residents are so accustomed to the benefits of civilization, which even in their country areas are trying to create comfortable conditions. The street washbasin for the cottage is one of these: the minimum set of amenities on the plot is simply necessary, because the hands have to wash quite often. Equipped near the house and beautifully decorated washbasin will undoubtedly add comfort to accommodation and will add to the design of the site.

What designs of washbasins exist?

There are several varieties of washbasins: with snacks and without them, suspended containers and structures on racks.

The simplest model of a washbasin is a three-four liter container made of plastic or aluminum, with a lid and pressure spout.

The rear wall of the washbasin in the picture above is equipped with a special fastening, for which you can hang the container on a nail, driven into a wooden vertical rack. Water is poured into the tank, covered with a lid and substitute a bucket under it for collecting used water. Water poured into it as it is used. The top wall of the washbasin cover has a slightly concave corrugated surface, so that it can be used as a soap.

Suspended washbasins with a clamping tap equipped with a magnet that fixes it in the raised state, represent a more advanced version of the simplest model.

Some models are equipped with a valve crane, thanks to which it is also convenient to adjust the flow of water. The rectangular fifteenalistic plastic container is installed on a sink tumba, which is substituted by a bucket for collecting water.

Often you can find on sale and washbasins on the rack. Portable washbasins on the legs can be accommodated anywhere on the site

Due to the presence of special roar on the design racks, the washbasin is firmly installed on the ground in the garden or garden, slightly blocking it.

The washbasin "Moidodyr" is convenient because the construct sink can be used as a container for washing fruits, vegetables, dishes. Some models provide hooks for towels, shelves for soap accessories and even small mirrors. Washbasins made of plastic or metal are designed to install on open areas. Wooden washbasins equipped with water heating system are more suitable for indoor arrangement.

Washbasins with a table are stationary structures, the main elements of which are: the bulk tank, sink and stand-stand-rack

The simplest washbasin of plastic bottles

Provide yourself with a minimal set of amenities and make the easiest version of the washbasin from a plastic bottle.

It is best to use a bottle of 2-5 liters as a container. Thanks to the transparency of plastic, it is convenient to control the volume of water in the container

First of all, you need to cut the bottom of the plastic bottle. The bottle itself is fixed on a post, grape arch or any rack with a clamp or wire.

The bottle cover can be simply left in its original form, or to upgrade it by performing several punctures in it or adds the pressure spout made of screw or nail

Washbasin Ready: It remains only to fill the container, slightly open the lid and use it for a direct purpose. You can watch a video with an example of making a similar option:

Another original device:

A comfortable portable washbasin with a crane can be built from a five-liter plastic canister, barrels or a bidon. Plumbing accessories will also be required for the manufacture of functional appliances:

• water faucet;
• clamp nuts;
• sgon;
• two gaskets.

In the selected container, you need to drill or cut the hole of the required diameter.

Signs are installed in the hole of the tank, the gaskets on it are put on it and clamp nuts. It remains only to attach a crane and pour into water tank

Highlighting the washbasin is desirable to provide drainage, taking away the spent water into a cesspool. Behind the absence of the ability to equip the drainage system, you can simply use the container for collecting dirty water.

It is possible an option for placing a washbasin over the ground, the eliminated layer of gravel, which will act as drainage and prevent the mud around the washbasin.

Wooden "Moydodyr" on its own

For the manufacture of a more complex stationary design, which will not only be a functional, but also decorative element of the site, you will need 25x150 mm boards. The dimensions of the design depend on the size of the capacity with water and the preferences of the owners.

In vertical blanks, make eyelets for the arrangement of spikes. To do this, with a milling mill, a groove of 20 mm depth and 8 mm width are cut. At the ends of horizontal blanks with a circular, spikes cut out

All billets of the washbasin are collected in solid designs and are connected using self-samples.

On the inner sides of the lower part of the design prepare the foundation where plywood sheets will be installed. Sheets can be placed on glue, or fix with small carnations

Between the side walls of the top of the design placed the tank. The floor of the washbasin is laying out of the rails 20x45 mm. The walls of the upper part are fixed using self-tapping screws, so that if the tank flows, it can always be removed. The principle of manufacturing the design of the structure is quite simple: to the frame, the planks of which are connected to each other with a spike groove, a sheet of plywood is glued on the inside. On the door frame set the lock with the handle.

Washbasin is ready. It remains only to carefully polish the product, paint, and then install the sink

Additional options - Video Master Classes

Today everything. If you have some questions, please write in the comments.

Solve problems with the water drive for the shower can be in two ways: to buy finished products in the store or make them with your own hands. The second option is much more preferable for several reasons:

• there is an opportunity to choose the volume of capacity for your own needs. Depending on the design of the shower and the number of family members, it is possible to establish a container with different volumes;
• if you wish, you can install additional automation systems. If there are minimal experience in performing plumbing work without big problems, you can make automatic tank filling, water fence only from the upper warmed layer, electric heating, etc.;
• low cost. All structural elements can be used, nothing needs to buy. If you have to go to the store, then only for cheap quantities;
• pleasure from independently done work. This is an important factor, in many cases all the others outweighs.

The article will give a detailed step-by-step instruction of the manufacture of several versions of the tanks for the shower, each has both strengths and weaknesses.

The shower tank can be metallic from galvanized sheet steel, stainless steel or carbon (black) iron and plastic. In order to consciously choose optimal options, you should familiarize yourself with the real comparative table of manufacturing materials.

Experienced practices are advised to make a tank for a soul from b / in plastic or metal containers. Such a container is easy to find, in most cases nothing will have to pay.

For one wash, it is quite enough to 40 liters, depending on the number of family members, you can calculate the optimal dimensions. For information it is worth saying that industrial companies during the manufacture of tanks for the shower proceed at the rate of approximately 20 liters per person, 40 liters allow not only to take a shower, but also fully disappeared without the need to save water.

Plastic barrels

A very common version of the manufacturer of the tank for the shower, differ in good indicators of physical strength. It is allowed to apply both new and use former in use. The volume may be different, from 50 to 1000 liters. For the soul there is no need to use large tanks, it is enough to have a volume within 50-200 liters.

For all plastic containers there are two general requirements:

• material of manufacture - resistant to ultraviolet rays plastic. It is quite difficult to find such containers, and they are not suiced;
• must have a dark color, and preferably black. Plastic should be painted with mineral paints during pressing polyethylene. Most plastic barrels of blue or white. Why is it recommended to have a container made by their painted plastic? Because the paints on the surface of the plastic can not be held for a long time, during one summer they will be twisted. The reason is not only in the low adhesion coefficient, but also in large values \u200b\u200bof temperature extensions. And all dyes negatively react to changing the linear size of the painted surface.

Step-by-step instructions for the manufacture of plastic tank

If you have an old plastic barrel, then it needs to be carefully flushed. Capacity can be considered clean only when different odors completely disappear. For installation in a vertical position, a frame should be made and the base, the emphasis is located across the entire bottom area. To reduce wind loads, it is better to put a barrel of the side of the side, but then problems arise with the sealing of the lid.

How to seal the cover

Step 1. Thoroughly rinse the connection site with a barrel, remove the oily spots, dust and dirt.

Step 2. Scroll through the cover, check whether it fits tightly across the circumference. If necessary, align the lid. For this, deformed spaces heat the construction hairdryer, install the cover in your place on the barrel and hurt much. In this position, the cover is held until complete cooling. Work in mittens, observe security measures.

Step 3. Re-degrease the surface and gently lubricate with special glue. If you have an apparatus for welding plastics - excellent, such a seam has a strength of not lower than 90% of the strength of the base material. If there is no device - use glue.

Step 4. Wait until the adhesive composition is completely dry. Time depends on the brand of glue and drying conditions.

Step 5. Re-apply glue in the places of fitting the lid to the barrel and again let it dry. Do not rush, do not allow skips.

Step 6. To increase the strength of the connection, once again lubricate the place of the joint and tightly wrap it with a clean polyethylene film. Top of film torn soft wire.

Instead of wire, it is permissible to use the clamp

If you have little experience of such work, then do not rush to install a barrel on the shower room, first check it on strength and tightness. Everything is fine - cut into the top of a small hole, connect the reinforcement and shower. Loves leakage and eliminate them fail - put a barrel in a vertical position.

How to make a cut in plastic barrels

Not such a simple question as it may seem. The fact is that it is precisely about the inserts that the points of increased tension of the material are formed, and the microcracks appear over the time, which increase until complete destruction. As a result, there are a barrel to change completely, repairing such leaks is very difficult. Yes, and after repair, no one can give a guarantee that in the same place or next to it after a few weeks, the problems are again not detected.

For high-quality sink, you will need a drill with a set of drills of the corresponding diameters, rubber gaskets, bolts and metal plates. The sink is made not only under the watering can, but also for the flow of water and draining surplus.

Practical advice. For all connections, use a silicone hose. It is not afraid of frost, resistant to UV rays and which is very important for plastic barrels, soft and does not create additional loads on the connections node.

Step 1. Buy the inserts for the tank. They consist of washers, rubber seals, fittings and nuts.

The number of pins depends on the number of pipelines connected to the barrel, and the diameter is selected taking into account the size of the conditional passage of the hose. Additionally, you will need a clutch for the crane, a crane, a shower, a float from the old drain tank. If you plan to install additional automation reinforcement, then simultaneously buy elements for fixing it to a plastic barrel. It is desirable to connect / disconnect the hose to use quick-dispersion, they make it much easier to care for the dacha tank.

Step 2. Prepare two metal plates on each insert size of about 5 × 10 cm, a thickness of at least one millimeter. It is at the expense of them that the site that perceives static loads from the connected plumbing fittings and dynamic efforts arising during the inclusion / shutdown of the watering can or the water supply valves can be significantly expanded. Be sure to remove sharp corners on all sides of the plates with a disc closure machine on all sides.

Step 3. In the center of the plate, drill a hole under the insert, for two plates you will need two holes, pass the sharp corners and bursavar after the drill.

Step 4. In barrel, drill the hole, the location must meet the requirements for the placement of the insertion and its specific purpose. In a round plastic barrel, it is quite difficult to drill a hole, the drill constantly "runs away", the greater diameter.

Practical advice. Drill holes will be much easier if you use simple recommendations.

1. Clamp in the passats of a small carnation and heat it with a lighter until a red glow appears.

2. Without giving time to the metal to cool, very quickly in advance marked place to register with a hot carnation in a plastic barrel a small hole, you can also have a non-separation.

3. Take the drill with a diameter of approximately 2 mm, drill through the hole. The label made will hold the drill in the desired position. It will be the center, then you can continue to work with a reduction drill.

Step 5. Entridly remove all burstles around the perimeter of the hole, they should not interfere with hermetically installed metal strips.

Step 6. Bend the metal plates along the radius of the barrel. Use for this by any pricks. There is nothing terrible if it is not possible to be perfectly bend the plate, but it is desirable to strive for such a result. The more accurate the radii, the larger the area of \u200b\u200bcontact, the smaller the load per unit area, the more efficient the device is valid.

Step 6. For a complete guarantee of the exception of leaks, lubricate the surface of the plates by any glue or sealant, you can make the same operations with the inserts.

Step 7. Install all elements in place, metal plates must be from two sides of the tank. For fixing the nut, the assistant will need, one is difficult to do it. But it all depends on the size of the container. Remember that standard rings have nuts with left-thread, screw them counterclockwise.

Constantly control the position of the plates, do not allow them to turn and change the initial proper position.

By the same algorithm strengthened holes for all sings. Do not be lazy to make a strengthen, it increases much of the time of operation of the tank for the country soul. Next to the thread, a crane, hose, fast connector or other equipment for the tank is fixed.

Video - installation of removal on plastic barrel

Metallic shower tank

We will not consider rather "exotic", in our opinion, options for the manufacture of stainless steel tanks. Let us dwell on the two most successful - from the finished barrel or welded steel of ordinary quality.

1. Metal tank of finished barrel

Initially, it is necessary to talk about the types of barrels, their advantages and disadvantages.

Metal barrel manufacturer

In the bottom of the barrel is made a hole for the soul watering. If the barrel is thinned, then it is recommended to install metal plates to enhance the connection location. How this is done - described above on the example of a plastic barrel. For water supply, the hole should be made in the upper part of the tank. During the manufacture of a frame for a tank, be sure to take into account the weight of the filled container, the fixation must be reliable and safe.

2. Production of leaf steel tank

The optimal option for many cases has a number of advantages.

1. Ability to manufacture a tank of any capacity. This allows you to maximize the needs of users.
2. The shower tank at the same time can serve its roof. For this, the size in length and width must respond to the shower parameters, the framework of the structure simultaneously serves as a frame for the tank. In step-by-step instructions, we will consider this option.
3. The tank is allowed to install all systems for automation of pouring and additional artificial water heating.

Step-by-step instructions for the manufacture of metal tank

For the manufacture, it is necessary to prepare sheet iron with a thickness of about 1 mm, the size of the sheets depend on the length and width of the shower cabin. For most cases, 1.2 m × 1.2 m is enough.

Step 1. Draw a sketch of blanks and calculate the volume of the tank. For example, we will take a volume of 100 liters. With a length of 1.2 m and width of 1.2 m, the height should be: H \u003d 100000 cm3 (100 liters): (120 cm × 120 cm) \u003d 6.9 cm. Round up to 7 cm. For the tank you need to prepare two plates size 120 cm × 120 cm for top and bottom. And four plates of 120 cm × 7 cm for sidewalls.

Step 2. Transfer sketches of metal blanks. Clean its surface from rust and dirt, accurately draw the contour of the workpiece. Dimensions need to be transferred only for one sidewall and tops, these items will continue to be used as templates for the rest.

Step 3. With a circular fluffy machine with a disk for metal cutting, cut the blanks. Check that the dimensions are fully the same.

Important. While working with the Bulgarian, follow the safety regulations. By trauma, this tool takes the first positions. The disk should rotate the operator, it is extremely important. Newbies are trying to change the direction of rotation, they do not like that sparks fly towards the worker. It is very dangerous, in this position, the Bulgarian can snatch, injuries from her complex and heavy.

Step 4.. Conduct sections of cuts, try to achieve the most flat line. The gaps of no more than two millimeters are allowed. Try to pre-fold all the items and check their quality.

Step 5.. Start welding individual items. Adjust the current strength of the welding machine and the diameter of the electrode. Metal should not be abrupt, this condition significantly reduces the strength of the seam. In addition, the strong current burns thin sheets through, close the holes are then difficult and long. Keep in mind that the weld during the cooling "pulls", the value of the corners changes. To avoid mistakes first grab two elements in several places and let them cool. After that, check the corners and, when detecting deviations, correct them. Only after such preparation can be applied to solid seams.

Step 6.. Take off the flux along the entire length of the seam, check its integrity. There are skipping - impose a re-seam. If the experience of the production of welding works is not enough, then professionals are recommended at the bottom of the shower tank to apply seams from the inner and outer side. The lid is welded only on the outside.

Step 7. Seat the location of the water input and canoe watering sites. Taking into account the diameters, drill holes, to the grinder to subduct burstages. We do not recommend you to boost the fitting with a carvings, much easier to purchase special cuts in stores. They have a set of washers and rubber pads, quickly installed in place, do not require special knowledge. Pretty adapters are quite difficult, newcomers will definitely be leaks.

Step 8. Repeat all the weld seams from the flux, pour water into the tank and check the tightness of the container. There is no leakage - pour water, clean the surface and paint the outer walls. Paint, of course, should be black and for external work.

The finished shower tank can be mounted above the shower. If you have a desire to make it from a stainless steel, then the technology is almost no different. Except for changing the welding and brands of electrodes.

You can find options for manufacturing a tank for a shower of galvanized sheet steel. Do not consider this option successful for several reasons:

• very thin walls require additional special measures to strengthen them;
• zinc has low adhesion with most coatings, paint will quickly suck. And use special expensive paints is economically inexpedient;
• for the manufacture of the tank, the elements used in the connection places are bend, and then searched. It is very long, you need to have or specially do bending devices;
• without a solid experience, the soldering of galvanized sheet gland is not necessary to hope for a positive result of its work.

How can you improve tanks for the country soul

Each owner of the country area, taking into account his needs and opportunities, can independently improve the tank, establish the simplest mechanisms that allow not only to increase the comfort of water procedures, but also reduce the cost of its service and preparation. We will not concern complex automation, consider only the most "budget" options. Although they are low-cost, but in terms of efficiency, safety and durability of use, there is no expensive analogues of industrial production.

Water temperature

For those who already use the simplest shower in the country area, it is no secret that the water temperature changes during washing. Sometimes the temperature difference can cause significant discomfort. It is impossible to completely eliminate such a phenomenon, but there are several ways to minimize the difference and increase the water temperature in the tank? We will not consider factors depending on the location and color of the surface, we will focus on purely technical solutions.

1. Make water fence on top of a tank. The easiest way, but very effective. To do this, you need to attach a flexible hose Ø 15-20 mm to the inlet opening. The main thing is not the size, namely flexibility, the hose can be made from various materials, the wall thickness does not have. The shower water moves by gravity, there is no increased pressure, on the contrary, it is somewhat lower than in the container due to physical phenomena arising during fluid movement. The length of the hose connected must be about 20-25 cm more than the maximum height of the barrel. Specific values \u200b\u200bare determined taking into account the features of the hose. The main requirement - it should not be completely blocked while working and not disturbing the flow rate of water. The upper end of the hose is fixed to any float (it is better to take a piece of foam) from the bottom. As they fill or empty the barrel, the float will move up / down, and the intake end of the hose always takes water from the warm top of the top layer.
2. Install the simplest electric heater. Now in the implementation there is a huge number of devices that differ in power, price and method of fixation. Choose for yourself the most optimal taking into account the maximum number of different factors. You can not focus on the power. In addition to the additional heating of water, the heater will perform another task - to constantly mix it in the tank. Mount it at the bottom, warm water will climb up, and cold go down. Due to the continuous mixing, the temperature of the water in the entire volume will become the same. If you wish, you can additionally install a temperature sensor or time, but it is already quite complex work. Yes, and the presence in the tank with water conductive elements has a negative impact on the safety of using the shower.

Filling a tank

There are two most frequently used tank filling methods: manually bucket or using a valve valve. Both methods are often used and have the right to life, but we advise you to make the third option, in our opinion very successful. In addition, almost no additional costs will be required, and all works will take no more than an hour of time.

Step 1. Prepare details. You will need a hose and an ordinary float mechanism from the drain tank toilet bowl. As a rule, they very rarely fail, such elements can be found and used for a tank during the replacement of plumbing equipment. If there are no old - buy in a specialized store, the price of devices is available to all consumers.

Step 2. Drive the hole in the container, do not forget to install additional plates to strengthen the scene.

Step 3. Install the float, use the sealants to exclude leaks.

Important. If for all cases described above, small leaks are considered an unpleasant phenomenon, but not critical, then with a float compounds should be hermetic. Otherwise, a large amount of water flowing can cause very unpleasant consequences.

Step 4. Adjust the position of the float with such a calculation so that the barrel is always filled with the desired volume. If there is a desire, you can make a drainage insured hole, insert the tube into it and bring out to a safe place. The tube will give the opportunity to notice the malfunction of the work of the float and minimize the consequences of the "Flood". But you can not do this, the shower at the cottage is not that room, to especially take care of the leaks, the main thing is that not all the water leaves. Of course, at the time of a long lack you need to not forget to completely turn off the water supply.

Heated heated, heat insulated shower, sensors and pump

Country souls

The version of the tank for the shower should always be thought out before the start of construction, and not the opposite. If you have temporary shower, then you should not lose a lot of effort and tank makers. You can meet options for use for these goals of fuel tanks from passenger and trucks, large canisters, dairy bids, etc. Professionals recommend paying attention to efficiency and, of course, the designer view of the soul. The tank should not be brought into the eyes, and fulfill its tasks "imperceptibly."

And last. In everything you need to observe the optimal ratio of value and quality. You have a landline shower that is planned to be used in cool autumn days - think not only about the electric water water in the tank, but also about thermal insulation. It should be removable and installed only in cases where the sun's rays are already not enough to heat the water to the desired temperature. It is best to use foam plates, they are quickly installed and removed, several seasons can be used. For the price arrange all consumers.

Video - shower tank with your own hands

Each owner of the country area tries to create comfortable conditions on its estate. This is especially true of the inhabitants of large cities, which are familiar with the benefits of civilization at hand. In addition, in the country you need not only to relax, but also work, and if you do not have a water supply, then you will face certain difficulties. We will tell you how to make a washbasin at the dacha with your own hands.

Correctly choose a seat under the washbasin

If you assume not only to come to the cottage in the evenings, but also live on it for several days in a row, then the permanent availability of water you need. Waking up in the morning, it's so nice to wash the cold water, getting a dream and cheer up to start working with new forces.

Most often we are faced with the lack of water supply and sewage in the country areas. Of course, you can independently drill well and provide the estate with an almost full-fledged water supply system, but this is a time-consuming and expensive occupation, besides, far from payback, especially against the background of what you will use only in warm season. In winter, without control, the pipes can be altered, burst, or even just divide the hands of unreliable social elements.

Therefore, we will choose our choice on a simple, lightweight and habitual design of the washbasin - Mojdodyra. The first thing to be solved is: where will this washbasin be installed - in the yard or inside the house?

Find a comfortable place in the yard for a washbasin

It will most correctly make or acquire such a construction that in summer, in the hot time, you can leave in the yard or in the garden, and with the onset of cold weather - to put in the room. So you do not have to adjust the sewage and water supply. The only thing you will have to decide - where exactly put Moidodyr.

The washbasin must be in an affordable place so that you can use them at any time. If you like warm water, install the construction on the sunny side so that the water-containing capacity is well warmed. However, many believe that it is better to place a washbasin in the shade, especially if the plastic container.

Well, another important question, what is the washbasin to choose? It all depends on your personal preferences and opportunities. Washbasins are:

• bulk;
• suspended;
• washbasins-racks with a table;
• washbasins with heated.

Each of these washbasins can be used as portable, and can be firmly fixed in a specific location. If you do not want to bother, then any view can be purchased in the store. But make it yourself, especially from the remedies, not only much cheaper, but also more exciting.

Using sweater means

Even if you still have only plans to create Moidodyra in the country, wash your hands and wash it all the same. In this case, we will come to the rescue, the simplest, marching option is a plastic bottle with a volume of 1.5 liters. Cut the bottom, turn over and secure on the wire to the tree branch, fence, etc. The water is poured on top and is well heated. You can make a full-fledged washbasin, having attached the holders for soap, toothpaste and brushes.

Plastic bottle washbasin scheme

So that the water from such a bottle flows is not constantly, and then, when it is necessary, you can use several devices.

1. The easiest way is a nail into a plug. In the center of the cover of the bottle, do the hole and insert a nail into it so that the hat remains inside. Tightly screw the plug. The cons in the fact that water is leaking, and from this nail rust, besides, it is not entirely comfortable to wash your hands with such a non-permanent supply of water.
2. The second way is easier to use. A hole is made on the side of the lid. When the lid is unscrewed, the water begins to pour as much as you need. Screw the lid - water will stop. The minus of the method is that it is not very easy to control the sufficient level of unscrewing so that the cover does not break thoroughly.
3. The third method is also simple: you can attach a crane, for example, from a washing machine, to the neck bottle with a tape. Water will go the way you need, and you can be sure that the crane does not break if it was well fixed.
4. The same crane (or purchased, from the economic store) can be attached to the plastic container with a volume of 5 liters. To do this, it is enough to drill the hole of the desired diameter and fix the crane in it. The tin or enameled bucket as a container is also perfect.

Such homemade manuals from the subwoofers can be disappeared by various drawings. Children will be very happy with the possibility of attaching fantasy and efforts for a common cause.

What can I make a washbasin in the country?

More complex washbasin design

Such a washbasin will be more severe, and therefore it needs to be installed at a permanent place. This implies the same place to plum, which, however, can be replaced with a bucket or basin. Copy used water can be accommodated for irrigation of small flower beds or beds.

So you will need:

• large capacity (bucket, canister, bidon volume from 10 liters);
• sgon;
• strips for crane;
• clamp nuts;
• water crane.

Make a hole on the container. It should not exceed the diameter of the camp. Depending on the material of the tank, select, drill or cut the hole, and place a Sgon into it.

Put on both sides of the brass rubber gaskets and fix the nuts on both sides. Now install the crane, and your garden washbasin is completely ready. Having it on the plot, pay attention to the soil at the installation site. If you do not plan to make a drainage to the cesspool or in the garden, then you definitely pour several gravel vestors under the washbasin. It will keep you from dirty puddles.

Use a larger plastic barrel for a washbasin

If you are not constrained in time and means, you can make a more practical and solid cottage washbasin along the same scheme. For him you will need:

• tank and plumbing fittings;
• sink of the desired size from a suitable material;
• materials for frame or tank connections with sink in one design;
• materials for supplying and removing water.

Build a frame of metal and wood, taking into account the size of the tank, sinks and hoses. Install all the elements to the finished frame, connect them to the water supply system and drainage. If you planned a bulk washbasin, then the connection to the water supply may not be required.

Choose a reliable water capacity

If in your plans, the manufacture of a washbasin with a table, then you should not independently do the water capacity from the girlfriend - you will only spend time, and it looks like this design will be non-source. The finished tank with the built-in crane is inexpensive, and it looks much more beautiful.

The optimal volume of tanks for the washbasin is 10-20 liters. Little takes no sense, but a larger suitable for the summer soul. As a tank to Moidody, it will be too bulky, and water in it can be stated.

Pay attention to the material from which the container is made. Prefer the stainless steel washbasin, it is durable and resistant to damage. Plastic is more easy and cheap, but it can crack from the blow, especially if filled.

The shape of a washbasin is also very important. From it directly depends on the water pouring from the crane. If the container is low and is in a horizontal position, the water will flow with a thin jet. As we remember from the school course of physics, the opposition is the greater, the higher the capacitance column. Therefore, it is better to choose a tank with an elongated up shape. The optimal version is a washbasin with a non-planning bottom, leaning towards the kolyan.

Carefully choose the tanks for the tank

You should not remind you that the crane must be located as close as possible to the bottom of the tank. Now washbasins are becoming increasingly popular, in which the valve crane is on the front wall. The pressure from it will be lower than from a washbasin of up to 5 liters with a clamping crane. In such a tank, water pressure is lost due to the location of the crane. Due to the loss of pressure, water in the container will have to simplify frequently. Therefore, choose a model with the lowest possible crane.

We make a tumba for Moydodyra on your own

Perhaps with old times you have a sink sink. It will great like a standard tank and sink. In this case, you will only need to clean it, paint, and maybe add a couple more elements to the design. Well, if there is no such washing, you can easily make a frame for yourself. For him, you will need wooden bars with a cross section of 50x50 - 80x80 mm or steel corners 25x25-40x40 mm.

The optimal height of the couch on which the sink is located is not more than 1 m. Take the corner or bar and cut 4 parts of 85 cm each. The size of the chanda frame must be such that the sink easily lay on its edges, so carefully measure the design elements.

Modern models Moydodyrov

Cut 8 pieces of timber (corner) under the sink size. As a rule, it is 50 cm. Collect the framework and fix: Fly, if the bar used, and boil - if the metal corner.

Please note: Focus on the inner edges of the frame, since the sink will be laid. Steel frame after making need to be projected and painted to avoid rust.

The skeleton of the cabinet can be seen with such materials:

• plywood shield;
• wooden plank;
• polycarbonate;
• steel sheets;
• plastic panels.

So that plywood and tree did not get into disrepair, sprinkling on the street, cover the design of varnish. The back wall and sides of the cabinets completely cut, firmly fixing the material on the frame. Front jumper on the loop door from the same material as the frame.

Make the floor in the cabinet from the board, leaving the gaps between them about 1 cm so that the spilled water goes into the ground and the air circulation was ensured.

Additional elements of the washbasin

It is possible not to be limited to the frame of the sink cabinet. To make it convenient to use the washbasin, make a tabletop that can serve as a dryer for dishes.

1. The dryer can be attached with both one and two sides. To do this, take wooden boards with a cross-section of 25 x 15 mm and run them so that the dryer is in the form of a lattice. The distance between the table should be 1.5-2 cm.
2. You can make a two-level dryer. To do this, at an altitude of 35 cm above the ground, make another framework and score on it.
3. Be sure to cover the dryer with varnish so that it does not smell over time and not spoiled from moisture.
4. For the tabletop, take a plastic or wood slab and place it on the frame made by the size of this slab.

Frame for a washbasin can be made independently

On how to organize a drain of water from the sink, we talked above. You can use the usual bucket in this capacity. This is especially good if you wash not only your hands, but also vegetables with fruit, as well as dishes with food residues. Thus, in water there will be organic remnants of products, and such a fall can be sent to a compost bunch for humus.

If product cleaning and food remnants are not discharged into the sink, then you can connect a corrugated pipe to the drain hole and take it to the wastewater.

Video on the installation of a washbasin on the country area

Now your garden plot is equipped with a comfortable and functional washbasin. We hope that our tips will help you make it quickly and easily. Tell us about your experience in the manufacture of dacha washbasins. Warm summer and easy work!