Moving the toilet from the riser to the side. Moving the toilet from the riser to another location: when design is more important than anything else Moving the toilet to another wall

The transfer of the toilet is most often done due to the small area of the bathroom. The owners have to use every centimeter of free space to expand the area. In most cases, this particular household toilet item takes up quite a lot of space.

Now there are too many design ideas that are hindered by its location. Therefore, the toilet is deployed or moved to a more suitable place.

Main reasons:

increase in the usable space of the room;
optimization of the bathroom area;
implementation of design ideas;
installation of plumbing equipment for a child.

The main reason for the transfer is the release of usable space in the plumbing unit premises. The owners want to move the toilet in such a way that they can install a washing machine, sink and other convenience items. And just free space makes the room spacious and comfortable. This is especially true of panel houses, old "Khrushchev" and similar buildings, where the bathroom has a small area or combined with a bathroom.

You will also need a transfer when you install the toilet directly opposite the door. This is inconvenient for use of the entire room and is dangerous for the equipment, as the door hits the body of the toilet bowl. Ultimately, cracks appear on it, which gradually destroy the toilet. In this case, the owners may incur additional losses.

A popular reason to move the toilet to another location is to implement design ideas. Celebrity design ideas involve moving equipment closer to a wall or to the opposite corner. This makes it possible to free up room space for the designer's creative thought.

Particular attention should be paid to the children's toilet - a full-fledged plumbing equipment, which is smaller in size and smaller in the volume of the flush barrel. It is best to move this toilet to the opposite corner.

Moving the toilet - possible risks

This type of work is associated with significant risks that the owners take on:

an increase in the length of water pipes coming to the toilet;
increased likelihood of blockages;
changing the slope of the pipeline;
the appearance of right angles in the plumbing system;
violation of standards.

Even if the toilet is moved close to the wall, it must be taken into account that an increase in the system of pipelines coming to this equipment can lead to problems. For example, when flushing water, a vacuum is formed, which will lead to the breakdown of the water seal in all plumbing located near the equipment. The process is accompanied by loud gurgling and unpleasant odors.

For the same reason, blockages appear. After all, the pipe coming to the toilet has increased in length. This creates conditions for a greater concentration of impurities. To avoid these phenomena, it is necessary to comply with the requirements of SNiP (building codes and regulations). With this approach, you will not only reduce the likelihood of breakdowns to a minimum, but also save your health and money.

When calculating the required slope of the pipeline, the standard should be taken into account, which says that for all elements with a diameter of 100 mm, the presented indicator should be at least 2 cm per meter. If there are parts with a diameter of 50 mm, installation should take place with a minimum slope of 3 cm per meter.

The reduced slope value slows down the movement of waste water and provokes the formation of stagnation of sewage in the pipeline.

A steep slope is also undesirable. In this case, water will pass at an increased speed, which will lead to the appearance of solid contaminants. The gradual accumulation of such formations will increasingly impede the flow of water, leading to blockage of the pipeline.

Compliance with SNiP is a key factor in the success of a toilet transfer. But if the transfer is more than 1.5 m, these recommendations will not be taken into account. If there is such a task, you need to install. This is also true at a shorter distance, if there is no desire or opportunity to work on adjusting the slope and installing additional pipes.

Various options for transferring the toilet from the riser

Moving the toilet from the riser can be done in two ways:

moving equipment over a distance of 10 to 20 cm;
moving equipment over long distances.

Before the immediate start of work, it is necessary to make all the necessary measurements and dismantle the toilet bowl. These are mandatory activities that will allow you to successfully move the plumbing equipment to the desired place and distance.

Moving the toilet at a distance of 10-20 cm

In both cases, it all starts with the dismantling of plumbing equipment. A complication here may be that the toilet is installed on cement or glue and its base is also coated with cement. Movements should be as smooth and accurate as possible. Otherwise, cracks will appear on the device, which will render it completely unusable.

If the device needs to be moved a short distance within 10-20 cm, then you need to shut off the water supply to the unit and perform the following actions:

freeing the space between the sewer bell and the base of the equipment from putty (a strong screwdriver or chisel is suitable for this);
careful loosening of the toilet (a wide chisel is hammered in different places of the base, the operation is repeated until the device begins to wobble);
lifting the toilet bowl is carried out as follows: feeding the device towards itself and removing the outlet from the socket of the sewer pipe (this should be done strictly along its axis), if the equipment is stuck, it is forbidden to pull with great effort, it is recommended to gently swing the device and pull it again.

Please note that all dismantling measures must be carried out as carefully as possible with serviceable tools. The toilet must remain in working order for correct subsequent installation in another place. Facilitates the work of standard fasteners and connection of the device to the sewer. The device is usually fixed with several screws.

For dismantling, it is enough to unscrew them and carefully remove the equipment from the mount strictly towards yourself along the axis of the pipeline. Next, it remains to remove the trigger.

Next, you should do the preparatory work for installing the equipment at a new location. It all starts with a thorough examination of the old flexible wiring. If it leaks or is not long enough, it must be replaced with a suitable equivalent. If no defects are found on the part, we leave it for further use.

To connect the outlet of the device to the sewer flare, use a corrugation with two seals installed at its ends. It is recommended to fill the connection with sealant for greater reliability. Next, you need to prepare the mounts. If they are made of steel, care should be taken that they are not pressed against the sanitary ware. For this reason, plastic washers should be fitted.

On the floor where the fastening will be carried out, accurate marking is carried out. Next, the necessary holes are drilled. If you are working with tiles, this material is drilled first (the diameter of the drill for the tile must exceed the same parameter of the drill for concrete).
Cleaning the socket of the sewer and the outlet of the toilet. These items must be completely clean and dry.
Applying silicone sealant to the inner part of the corrugation and fixing it to the outlet of the device.
Installing the toilet in its proper place, fixing the fasteners in the pre-drilled holes, and then tightening.
Gaps may occur between the floor and the equipment. They should be carefully covered with a solution. This also creates additional support that will prevent the base from collapsing under the influence of lateral forces.
Lubrication of the other part of the corrugation with silicone sealant and connecting it to the sewer socket.

How to move the toilet a long distance

To move the toilet at a distance exceeding the specified parameter, you should prepare for the alteration of the sewer. To do this, you need to build up the sewage system. In most cases, a plastic pipe with a diameter of 110 mm is used for this. The length, number and configuration of auxiliary elements depend on the installation site.

Plastic piping can be fixed to the floor or to the wall with clamps. To lower the sewer to floor level, remove the tap to the plumbing equipment from the tee or cross.

If the owners are dealing with plastic, it will not be difficult to do such procedures. It is better to heat elements made of cast iron with a blowtorch or gas torch. This is done so that the cement putty spreads and the sealant burns out thoroughly.

If the connections are filled with sulfur, they also need to be warmed up with a lamp. This produces very unpleasant odors. For safety, you should perform the procedure in a gas mask, in a well-ventilated area. In the event that everything is done correctly, it will be easy to remove the pipe from the socket. Next, you have to perform a number of standard actions for dismantling and installing the toilet.

If the task is simply to turn the toilet at any angle, you must use a tee, angle pipes or corrugation. In the latter case, the work is simple, but the connection system will be short-lived. In addition, contamination may periodically appear in the corrugation cavity, which must be disposed of.

Creating a comfortable environment is impossible without redevelopment of the premises, which also affects the toilet in the apartment.

Possible problems when moving the toilet

The increase in the free space of the toilet room prompts the thought and reinstallation of the bathroom. Is it realistic to move the toilet to the side?

Yes, but in order for the plumbing to function correctly, you need to know some subtleties.

Experts voice the following nuances of such a transfer:

The likelihood of blockage increases with distance from the riser, because sewage travels a long way.
Water flushing is accompanied by an unpleasant odor (sewer stench) and gurgling sounds. In a long pipeline, a high vacuum is formed, which leads to the suction of water from the devices (nearby plumbing) and the disruption of their hydraulic seals.

With the right approach to solving the issue, such problems can be avoided. Moving the toilet bowl from the riser - a process that is regulated current standards (SNiP).

Sewer pipeline requirements:

Use of pipes, the diameter of which is in the range of 50 ... 100 mm. The optimal section is considered to be 100mm, supplied to the toilet (minimal risk of rarefaction or "plugs" from sewage).
The maximum distance from the toilet bowl to the riser is 1.5m. If the pipe is longer, the capacity of the cistern is not enough to push the fecal matter through. They settle on the walls of the pipeline and a blockage is formed.
Observance of the correct slope. For each meter of the pipeline, it is 2cm (section 100mm) or 3cm (for 50mm section).

If the angle of inclination of the drain is too low, 100% clogging of the sewage system is guaranteed, since the fluid flow rate decreases. If the slope is too high, the flow develops an excessive speed, which causes solid particles to accumulate in the pipe. As a result, the movement of water is blocked.

The easiest way to get the required slope is to provide a podium for installing the toilet, raising it above the surface (sometimes by a significant amount). Plumbing communications can also be hidden here.

Lack of right angles when laying a new sewage system. If this condition is not fulfilled, installation at an angle of 45 ° is allowed (two such angles instead of one right).

If you put a toilet bowl in an apartment, taking into account these simple rules, then the likelihood of a blockage will be minimized (drains are discharged by gravity).

In practice, in order to move the toilet, you will need to perform a certain sequence of actions:

Mark the distance that you can move the bathroom. You will need to fix one end of a one and a half meter twine on a riser and draw an arc with chalk (tied to the other end of the rope).
Select the most suitable location for the toilet and install it. It is advisable not to leave the maximum distance marked on the floor.
Measure the difference in height between the center of the drain pipe and the floor. Compare the received data with the height of the inset point. If it turns out to be higher, you will have to build a podium, with the help of which the drain pipe rises 30 mm above the tee of the riser (tie-in point).
Fix the plumbing fixture on the podium (floor) and connect it to the drain system, ensuring the piping is as straight as possible (avoid right angles).

It is not at all necessary to carry out a rigid supply of cold water to the toilet, it is much easier to use a long flexible hose.

Toilet in the apartment: how to carry out the transfer of the toilet from the riser

Creating a comfortable environment is impossible without redevelopment of the premises, which also affects the toilet in the apartment. Increase the free space of the toilet

Ways to transfer the toilet from the riser to another place

Due to the small area of the bathroom, often, when carrying out a major overhaul of the toilet, it becomes necessary to move the sanitary equipment. In order to effectively use free space, as a rule, many people prefer to redevelop the premises.

The result of these works is the transfer of the toilet bowl from the riser. Since this process is associated with issues of water supply, drainage of the device, its solution must be taken as responsibly as possible.

Reasons for moving the toilet

Before proceeding with the processes of dismantling the old toilet and installing a new one, we will consider the main reasons for its transfer.

Changing the layout of the bathroom. In this case, all operations are coordinated, at least, with the Housing Inspection, the State Sanitary and Epidemiological Supervision, the State Fire Inspection, the Architectural and Planning Department. Only after obtaining permission, the toilet room is redeveloped. When moving a wall, the old arrangement of the device can cause discomfort, which is why it becomes necessary to transfer it.
Replacing an old device with a new one, which is much larger. If, due to the dimensions of the updated design, it cannot be installed in its previous place, the product should be moved.
Purchase of new furniture for the washroom.

Remember, regardless of motivation, the old toilet should be removed intact, rework the sewage system, and only then proceed to install the device at another point in the restroom. For this purpose, a long flexible eyeliner is often used.

Moving the toilet (easy way)

This method involves the movement of sanitary equipment at a distance that does not exceed 30 cm.

Before proceeding with the installation of the structure in a new place, it is necessary to dismantle the old device.

The sequence of work depends on the method of installing plumbing.

If the device is fixed with standard fasteners, and its outlet is connected to the sewer with a rubber cuff, it is necessary:

unscrew the screws that fix the toilet to the floor;
pull out the outlet of the device from the socket of the sewer line

Consider the sequence of work in the case of placing the toilet on an adhesive or cement base.

Before dismantling the device, close the water supply valve to the tank, and also drain the liquid from the tank.

Remove the putty between the outlet of the structure and the sewer socket.

Remember, work must be done as carefully as possible in order to exclude the possibility of a split in the outlet, otherwise the device is not subject to further use.

Loose the toilet. For this purpose, a wide chisel is driven in from different sides of the base of the structure.
Pull out the outlet, strictly along the axis, from the sewer socket.

After successful dismantling of the structure, they begin the process of installing the product. Since the distance from the new location of the toilet to the water supply and sewerage system is small, there is no need to build up pipelines.

Let's take a closer look at the process of installing the toilet in a new place.

Clean the outlet of the device and the sewer bell.
Mark the new holes in the floor covering for the toilet seat and then drill them out.
Put on the corrugation on the outlet of the device, while it is important to first apply the sealant to the surface.
Cover the gaps between the base and the flooring with cement mortar, this will create additional support for the structure.
Insert the corrugation into the socket.

After performing the above operations, you should check the operability of the device..

Moving the toilet (hard way)

If you need to move the device to a distance that exceeds the length of the corrugation, it is necessary to rework the sewage system.

The assembly and disassembly of the device will be similar to the simple method. At the same time, in order to build up the drainage pipeline, a plastic pipe with a diameter of 110 mm is used.

Remember, the length of the structure and the choice of corners depend on the location of the toilet.

Nuances to consider when assembling a plastic sewer

Ensure that there is a slope towards the riser: 2 cm per linear meter.
When removing from the tee, the cross of the cast-iron branch to the device, you should first warm up the socket with a blowtorch. The result of this procedure is the burnout of the cable seal and the cracking of the cement putty. After that, it is necessary to remove the pipe from the socket.

The installation of the sewage system should be carried out directly from the riser.

To insert a plastic pipe into a cast iron socket, use a gasket seal.
The gray-filled cast iron pipe joints are annealed with a blowtorch.

Remember, in order to minimize labor costs, instead of precisely fitting the plastic pipes of the drainage system to the toilet outlet, you can use a corrugation.

For the effective functioning of the sewer system, it is important to take into account the following rules in the process of connecting plumbing equipment.

The greater the distance from the toilet bowl to the sewer pipe, the higher it should be placed. This will create the necessary slope of the pipe for the smooth drainage of waste water.

If the structure is far away from the riser, it is necessary to provide for the construction of a podium.

It is forbidden to fasten the toilet bowl, pipelines to the inter-apartment walls, as well as displace the sewer risers.
Connect plumbing fixtures to the main line at an angle of 45 or 135 degrees.

Remember, you cannot connect the toilet to the sewer system at a right angle, as this will inevitably lead to the formation of a blockage in the pipe.

For the possibility of carrying out preventive work, in the places where the pipeline turns, it is important to provide for the presence of special hatches.

Thus, if it is necessary to transfer the toilet bowl from the riser to a new place, it is important to initially consult with the architect, familiarize yourself with the rules for installing the structure, measure the distance from the sewer system to the device, and only then choose the necessary method and start the process of performing the work.

Ways to transfer the toilet from the riser to another place

Methods of transferring the toilet bowl from the riser to another place Due to the small area of the bathroom, it is often necessary to move during the overhaul of the toilet room

How to properly move the toilet from the riser when combining a bath with a toilet?

Good day! Conceived a bathroom renovation. We want to combine it with a toilet. For the convenience of redevelopment, you need to move the toilet. I doubt it is possible ... Is it real? And how to make sure that you do not run into problems in the further operation of the equipment?

Hello! You can move the toilet a little distance from the riser. However, this, seemingly simple, event has many nuances, on which the further use of the equipment depends. Plumbers warn that the greater the distance of the sewer riser has to be overcome by sewage, the higher the risk of blockage. Some "masters" argue that this is not so, because theoretically pollution will "get" to the target anyway. This is true, but there are much more opportunities to "gain a foothold" in place on a long journey.

Another problem is the appearance of an unpleasant sewer odor in the room. It is associated with excessive vacuum, which is inevitable in too long sewer pipes. In this case, each flush will be accompanied by the suction of water from all nearby plumbing fixtures and the breakdown of their hydraulic seals. In addition to smells from the sewer, unpleasant gurgling sounds will also appear. To do without the above problems, you should follow the recommendations of the current SNIP.

In some cases, when moving the toilet from the riser, it is required to raise the equipment to a small podium in order to provide the necessary slope for the sewer pipes

The document prescribes to move the toilet bowl no more than 1.5 m from the sewer riser. In addition to the "correct" removal, you must also observe the desired slope under which the pipeline should be laid. For parts with a diameter of 100 mm, the slope should be 2 cm per meter. For elements with a diameter of 50 mm, the slope cannot be less than 3 cm per meter. These recommendations should be strictly followed, otherwise problems with blockages cannot be avoided. Decreasing the recommended parameters will lead to a decrease in the speed of fluid movement, which will lead to blockages. Increasing the slope, on the other hand, will cause the water to move too fast. It will not have time to capture solid dirt, which will begin to accumulate in the pipe and, over time, will completely block it.

It turns out that most often the toilet has to be lifted when it is moved to another place, in order to thereby provide the necessary slope for the pipes. In this case, depending on the transfer distance, a fairly decent amount of lift can be obtained. In addition, the pipe connecting the riser and the toilet will also have to be masked somehow. Given that its diameter is large enough, it may be necessary to raise the floor or equip a small podium, especially for plumbing equipment.

Another important detail: when laying a new pipeline, right angles must be avoided. If you cannot do without them, proceed as follows: mount two corners of 45 ° instead of one at 90 °. Otherwise, the likelihood of blockages in the pipe increases dramatically. All of the above requirements are mandatory when moving the toilet. However, even they do not work if it is required to move the equipment to a greater distance than indicated in the SNIP, or if its recommendations turn out to be difficult to implement. There is a solution in this case too.

The first is the transfer of the riser itself, which is extremely troublesome. The second is the use of special equipment that is intended for forced sewage. It makes the system work in conditions where ordinary gravity sewage cannot cope with its functions. For the arrangement of such a structure, a sololift or fecal pump is usually used. This is a compact device that can be placed behind the toilet cistern or even inside it. The device, which is a powerful pump equipped with grinder blades, pumps out sewage, grinds solid waste, and pushes the resulting mass into the sewer.

One of the main advantages of the equipment is the ability to use small-diameter sewer pipes: from 18 to 40 mm, which are very easy to hide even behind a plasterboard wall. The pump power is high enough. With its help, you can easily remove sewage at a distance of about 5-7 m vertically and about 100 m horizontally. No additional construction work is required to install the device. When choosing a sololift for forced sewage drainage, you need to take into account that if you plan to connect a washing machine or a shower cabin to it, you need to choose models with relatively high temperature limits for drains. Otherwise, the device will fail very quickly.

Versions are available with short-term protection, which allows the pump to pump hot wastewater. However, it is only designed for half an hour operation. Constant work with heated liquid is also contraindicated for such devices. In the technical part, the recommendations for moving the toilet bowl from the riser are not much different from the standard instructions for connecting the device. The only difference is the installation of a longer, sloped pipeline. Installation of the grinder pump is carried out in strict accordance with the requirements of the instructions.

How to properly move the toilet from the riser - advice from an expert

When redeveloping a bathroom, it is often required to move the toilet a certain distance from the riser. Let's consider the problems that may arise and the ways to solve them.

Is it possible to move the toilet in the apartment to another place?

everything is possible, you just need to take it seriously and find out everything. Of course, you can put the toilet in the middle of the room and enjoy life, only if you make the wrong sewage and drain, then soon the whole room will be in.

Very important! For each meter of the outlet, there should be a rise of about 3-4 cm, otherwise the contents of the toilet will simply not go away, etc. Thus, if you are going to move the toilet 2 meters, then at the base of the toilet the height of the connection should be 7 cm, if by 3 meters, then about 10 cm. Can you afford such a rise? After all, to do this, you need to either put the toilet on a pedestal, or raise the floor.

Not everything is so simple, from a technical point of view, you can move the toilet anywhere, even to the living room, bring water without problems, but the slope of the pipes cannot be sustained over a length of more than 5 meters, the toilet will simply be “under the ceiling”, there is a way out forced sewerage.

Technically, everything is solved, the problem is different.

Bathrooms should not be installed above kitchens and living quarters of neighbors below.

This is the first point that sharply limits the concept of “elsewhere”.

From other places, there remains the bathroom itself, inside which you can move the toilet anywhere and the corridor.

The toilet in the hallway is fun, but not very convenient.

There are exceptions, if you live on the ground floor and there are no residential or utility rooms under you (workshops in the basement, gyms, etc.), then you can move wherever you want.

Or if you are the owner of a duplex apartment.

In this case, your toilet bowl, above your own kitchen, may well be installed.

You can move the toilet and nothing, and no one will bother you to do this, only, in addition to putting it in a convenient desired place, you need to connect it to the water supply (this is not such a big problem) and the sewage system is already more complicated here!

The water supply problem can be easily solved, it is not difficult to re-solder the plastic or put a longer supply hose, but you cannot accelerate much with the sewage system, there should be a central riser nearby, since laying a 100 mm pipe or corrugation is too far not aesthetically pleasing, and it is fraught with blockages.

Therefore, a riser is needed, in apartments they are often found in bathrooms and in closets and even happens in corridors and kitchens, respectively, all adjoining rooms will be in the access zone to them.

You need to decide, connect and equip a suitable room - that's all, if you are afraid of problems with the housing, do not be afraid, but do not tell everyone at every corner, otherwise you will have to register the redevelopment!

Is it possible to move the toilet in the apartment to another place?

In some cases, when moving the toilet from the riser, it is required to raise the equipment to a small podium in order to provide the necessary slope for the sewer pipes

Choosing a sewer installation, video

Good day! Your problem is completely solvable. SNiP allows the transfer of the toilet, but warns that the distance from the plumbing fixture to the sewer pipe should not exceed 1.5 m.There are two reasons for this:

A large distance provokes an excessive vacuum in the pipes. How does this threaten the owner of the apartment? At least a constant unpleasant smell of sewage in the apartment and loud gurgling sounds emanating from the plumbing. The fact is that an excessive vacuum in the pipes with each flush will "suck" water from all nearby plumbing fixtures and tear off their hydraulic locks, the main function of which is to prevent the penetration of unpleasant odors into the room.
The longer the sewer pipes, the higher the risk of encountering blockages. Theoretically, sewage will be able to get to the riser anyway, but the more distance they have to overcome, the higher the chance of them getting stuck in the pipe. In addition, it is important to observe the optimal slope of sewer communications. If the slope of the pipe is insufficient, the speed of movement of sewage will be low, which will inevitably lead to the appearance of a blockage. If the slope of the pipeline is too great, liquid wastewater will drain too quickly, but solid sewage will stop and accumulate.

So, in order to move the toilet a certain distance from the riser and not run into problems, you need to follow three rules:

The distance from the riser to the plumbing fixture cannot be more than 1.5 m.
The slope of a pipe with a diameter of 100 mm should be 2 cm per meter. Smaller elements with a diameter of 50 mm are stacked at a slope of 3 cm per meter.
Lack of right angles. If for some reason this is not possible, you need to lay two 45 ° elbows instead of one 90 ° piece.

In practice, the second step is troublesome. This is due to the fact that it is impossible to provide the desired slope at a short distance. Therefore, most often you have to raise the toilet above the floor level and place it on a small podium. This solution is considered optimal, because it makes it possible to provide the desired slope of the sewer pipe and at the same time hide all communications. Alternatively, you can raise the floor level, which is no less troublesome. In addition, in this case, the height of the room will decrease.

To ensure the desired slope of the sewer pipe, the toilet can be raised to a low podium

It happens that you need to move the plumbing to a greater distance than recommended in the SNiP, or for some reason it is impossible to fulfill the above requirements. Even in this case, you can find a solution to the problem, or rather, two at once. The first is to move the sewer riser. It is highly undesirable to do this, since the procedure is very troublesome and time-consuming. A simpler solution is the installation of special equipment that provides forced sewage. The device will force the system to work in such conditions when the traditional gravity drainage system will not be able to function normally.

The optimal solution is to install a fecal pump or, as it is also called, a sololift. The equipment is a pump equipped with bladed grinders. The device forcibly pumps out sewage, grinds solid waste with blades, and then pushes the resulting mass into the sewer. The device is compact and easy to install. Moreover, to install it, you will not need to perform any additional construction work.

Depending on the capacity of the equipment, it makes it possible to drain wastewater up to 100 m horizontally, and vertically by 5-7 m. In addition, if necessary, the pump allows the use of pipes of small diameter: 18-40 mm. If you plan to connect a shower or washing machine to the sewer system, you need to choose the right model of the sololift. Most of them are designed to work with cold drains, hot ones will disable the device. Therefore, it is worth choosing a device that is designed to work with high temperatures.

Sololift is a compact device that is installed behind the toilet

A small nuance: there are models of pumps with special protection, which allows the device to pump hot waste water. However, this protection is short-term, its effect does not exceed 30 minutes. Constant work with hot liquid is contraindicated for such devices in the same way as for conventional mechanisms. Therefore, it is still better to choose a heat-resistant device. Thus, the transfer of the toilet is quite possible, choose any method that suits you.

The human being has a craving for comfort. He tries to improve his home, making it even more cozy and comfortable. Very often, such changes affect one of the most important places in every home - the bathroom. It has a small area where homeowners want to place as many useful things as possible, so they strive to use every free centimeter. The result of design research often becomes the transfer of the toilet bowl from the riser, an event that is not easy and responsible. How to do all the work correctly? Let's figure it out.

At first glance, moving the toilet bowl some distance from the sewer pipe does not pose any problems. However, it is not. Experts warn that the further the equipment is installed, the longer the way the sewage will have to overcome. Theoretically, in any case, they will "get" to the goal, but the probability of blockages increases many times over. Another problem can be the risk of high vacuum in excessively long pipes. In this case, with each flush, it will suck water from the nearby equipment, breaking the water seal. The process is accompanied by loud gurgling sounds and unpleasant sewer odors.

A twisted connection can cause frequent blockages

In order not to encounter such problems, you should strictly follow the instructions of the current SNIP. He does not recommend removing the device more than 1.5 m from the riser. A certain slope must be observed under which the pipe is laid. It is 2 cm per meter. This value is set for pipes with a diameter of 100 mm. If the diameter of the part is 50 mm, the slope should be 3 cm per meter. Increasing the recommended parameters will lead to the fact that the water will drain too quickly, without capturing solid contaminants that may accumulate in the pipe. Decreasing the slope will reduce the fluid velocity, which can also lead to blockages.

Moving the toilet is often the only solution to optimize the space in the bathroom

It turns out that the new place will have to be lifted. Depending on the distance from the riser, a decent value can be obtained. In addition, do not forget about the pipe going to the equipment, it will need to be disguised in some way. Given the diameter, it may be necessary to raise the floor to a significant height or equip a special podium. Another nuance: lay a new pipeline without right angles. If this is not possible, instead of one 90 ° angle, make two 45 ° each. Otherwise, the risk of blockages increases dramatically.

To provide the desired slope, you will have to make an ascent

Despite the fact that all the above requirements are quite troublesome to fulfill, they are mandatory when transferring plumbing equipment. But these recommendations do not help if you need to install the device at a great distance from the riser or, for some reason, you do not want to scrupulously comply with all SNIP requirements. Either the transfer of pipes, which is extremely difficult to carry out, or the use of special equipment designed for the arrangement of forced sewage will help.

Devices for compulsory waste disposal

It is a system designed to work when traditional gravity construction fails. For its arrangement, a device called a fecal pump or sololift is used. The equipment is rather compactly placed inside the tank or behind it. It is a pump equipped with special chopping blades. It pumps out waste water, grinds solid dirt, sends the resulting mass where it should be.

At the same time, it is very important that the diameter of the pipe used can be small - from 18 to 40 mm, which makes it possible to easily hide them, for example, behind a plasterboard wall. The capacity is quite high, which makes it possible to divert wastewater to a distance of about 100 m horizontally and about 5-7 m vertically. The latter may be relevant if the level at which the bathroom is located is lower than it should be. Installation is quite simple, without the use of additional construction work.

Compact grinder pump located behind the toilet

The pump has a temperature limit for the waste water. The maximum values range from + 35C to + 50C. This information should be looked for in the passport. It will only be relevant if, in addition to the toilet bowl, a shower, bidet, washbasin, etc. are also connected to the pump. For this, an additional inlet is provided on the body. If the requirements for the temperature of the pumped liquid are not observed, the device will fail. On some models, you can find special short-term protection that allows you to pump hot drains for about 30 minutes, but this cannot be done constantly.

Types of fecal pumps.

The equipment is very easy to maintain. All that is required of the owner is to periodically clean. For this, together with water, a special solution is poured, destroying deposits on the walls. It is important to ensure that organic solvents do not enter with the drains, the substance can corrode the rubber seals. The main disadvantage is considered to be its volatility, which does not allow the mechanism to function during a power outage.

How to move the toilet from the riser: a description of the process

The recommendations for transferring in the technical part differ very little from the instructions for connecting the equipment. The only difference will be in the installation of a longer piping connecting the device to the sewer. But the installation of a grinder pump differs in some nuances, which are worth considering in more detail. Purchase a device with an inlet diameter that matches the diameter of the toilet outlet. Otherwise, the installation will simply be impossible.

The diameter of the inlet pipe must match the dimensions of the outlet

Competent installation of equipment is carried out according to the manufacturer's instructions. It includes stages:

We insert supply pipes or connecting bends into the branch pipes.

We install the pump behind the toilet, fix it securely with screws to the floor. For this, there are special holes on the body of the device.
The pipes that fit the pump must be laid with a slope of 3 cm per meter. Thus, the flow of wastewater by gravity will be ensured.
We connect a drainage pipe to the outlet.
Models with a separate ventilation duct require the ventilation duct to be routed above the ridge of the building's roof. It is mounted after connecting the device. There are simpler options to ensure that there is no unpleasant odor using a charcoal filter built into the housing.

Models with built-in charcoal filter are easier to install

We connect the equipment to the network. If the model is equipped with a plug, it is connected to electricity. If not, then it connects to the network through an RCD machine.
Connections of pipeline elements are carried out by welding, soldering or adhesive joints. All bends of the inlet and outlet pipe elements to be adjusted should be as smooth as possible.
The device also removes waste water in a vertical plane. If necessary, a vertical pipe section should be equipped no further than 30 cm from the outlet. Otherwise, it will be impossible to ensure normal pressure inside the pipeline.
At the outlet of the grinder, we must install a check valve, which is necessary to prevent the return flow of sewage in an emergency.

Any redevelopment, no matter how simple it may seem, must be carried out extremely competently. This is relevant for cases when the typical arrangement of plumbing equipment changes. Everything must be carefully calculated and accurately executed. Even small mistakes can lead to chronic problems in the form of constant blockages and unpleasant smell from the bathroom. Those who do not have experience in carrying out work of this kind, it is best to contact specialists. They will consider specific conditions, give recommendations on the purchase of the necessary equipment, and conduct it with high quality. Only in this case it is possible to guarantee the good performance of the toilet, which will be installed where the owner of the home has planned.

Also on the topic

The deputies did not fulfill their pre-election programs Feel free to promise social benefits and reduction of communal services

Fantastic creatures of the Murmansk fisherman conquered the British media

Biography of catherine lyubimova

Online chart and dynamics of the RTS index over the past ten years: what's next?

Orthogonal projection area theorem