If such a situation arose that you purchased a ready-made mosquito net, but do not know how to install it, this instruction will help you deal with this problem.
Self-installation on plastic windows
In the case where you already have a mosquito net along with mounts (z-shaped), then you should perform the following list of tasks.
Installation sequence using metal fasteners:
As you can see from the instructions above, this is not such a difficult task. Note, however, that this instruction is effective for a certain type of structure.
Fastening with plastic corners
The next most popular option for mounting anti-mosquitoes on windows or balconies is mounting with plastic corners. This method of fastening cannot be attributed to the optimal ones, however, in spite of everything, it will look great on it, because it is quite common in the list of services of various companies.
This method differs from fastening with metal fasteners in that the fastener itself is installed on the window frame, and not on the mesh frame.
So, let's move on to the installation instructions:
Installing a mosquito net on a door
They are divided into two categories: they are both freely hanging, and in a special 
frame body. Self-installation of such structures is quite troublesome. This is due to the fact that they are delivered in a complete installation kit intended for specialists.
If we consider door nets with a frame, then they are fixed with hinges in the likeness of ordinary doors. When it comes to freely hanging species, then they are fixed around the entire perimeter, and connected with a magnetic fastener in the center.
Installation of a sliding option
The fundamental differences in installation on an aluminum window differ little from those options that were discussed above. Like a closet door, the sash is installed as follows:
- Directly, the mesh (sash) is brought behind the upper guide.
- In the maximum upper position, the lower end is inserted behind the lower guide.
- After that they lower it.
Now you know how mosquito nets are attached to plastic windows.
Hello dear readers! Summer is coming and so that mosquitoes, flies and dust with garbage do not fly into open windows, you put mosquito nets. Right? But not everyone has them. My friends on the balcony did not have a mosquito net and one day a cigarette butt flew to them from the upper balcony, which fell on the carpet.
That, in turn, caught fire. Fortunately, everyone was at home and managed to notice, put out. After that, they immediately ordered on all grid windows. I also talked to my neighbor about this. Whether he took it or not is unknown. In general, today the topic is about mosquito nets. Read!
A modern window cannot be imagined without a mosquito net. Nocturnal buzzing of insects and poplar fluff filling the house are a thing of the past, thanks to this simple and convenient accessory.
Convenience and ease of fastening made mosquito nets the most popular accessory for new plastic windows. But everyone wants to have as much fresh air in the house as possible, and windows do not always allow the rooms to be completely ventilated.
In honor of the opening of the summer season, the Moscow Windows company has introduced a new type of mosquito nets into the assortment - swing nets for balcony doors. Now there will be even more fresh air in every home.
Until recently, installing a mosquito net on a balcony door was not possible. Many craftsmen, of course, pulled gauze and experimented with other materials at hand.
Now this is not necessary, because professionally made hinged mosquito nets will easily fit into any door profile. Mosquito nets "Antikoshka" Does your cat like to sit on the windowsill and sometimes even tries to hunt the birds that fly by?
And then, of course, he starts stretching and scratching his claws on a mosquito net? And no matter how much you try to explain to him that you can’t do this, he still does harm and strives to squeeze out the net. One word - spring. Or maybe it's his birds that drive him crazy?
If you live no higher than the 10th floor, then you may have seen how sometimes hungry birds fly up to the windows and try to get midges that have clogged in from the window mesh. Of course, let the birds eat, but your net suffers!
To make your life calmer, the Moscow Windows company has introduced a new product into its assortment - nets with reinforced PVC coating "Antikoshka". What it is? We tell: the usual aluminum base with weaves is coated with a chemical composition of polyvinyl chloride (PVC).
This substance is completely safe for a person, the coating does not interfere with the light and air entering your house. But from industrial gases (chlorine, nitrogen dioxide), solutions of salts, basic acids, alkalis and moisture, it also saves from midges and mosquitoes along the way.
Additional processing allows you to make the mosquito net so strong that it is almost impossible to break it and somehow spoil it. Even for birds and cats. The mesh is attached to the window with special fasteners. We especially note that "fasteners" - from the word "strong".
That is, now your cat will definitely not fall out of the window (owners of cats, sleep well). And hungry birds, even if they eat stuck midges, still will not violate the integrity of the grid.
And although traditional medicine recommends to protect yourself from mosquitoes with the help of the smell of cloves, anise or eucalyptus, the Moscow Windows company knows that the best remedy is mosquito nets. Mosquito net care
Mosquito nets are recommended to be removed for the winter. If necessary, but at least once a year, wash the mesh with warm soapy water. Fasteners do not require maintenance. To calculate the size of your mosquito net, you need to measure the light opening of an open window and add 20 mm on each side.
Source: mosokna.ru
Reasons to buy a mosquito net
Anti-cat mosquito nets protect the house not only from insects, but also from dust and various allergens (poplar fluff, pollen, dandelion seeds, etc.).
Ordering a mosquito net is especially important for people with asthma and allergies. In this case, it is not so much about comfort as about health.
In addition, a high-quality mosquito net made of fireproof material will prevent cigarette butts thrown by neighbors from the upper floors from entering your house.
If you have pets living in your house, then you should buy a mosquito net for a window of increased strength Antikoshka, which performs two tasks at once: it protects you from insects and saves pets from falling out of the window. Also, such a reinforced mesh will be a good safety measure for families with small children.
Where to order mosquito net for windows
You can buy mosquito nets of different types in our company (anti-cat, ultraview, anti-pollen, anti-dust, anti-mosquito, etc.). We offer our customers only high quality products from trusted manufacturers.
They are made of environmentally friendly materials that do not emit odors. The prices for mosquito nets for windows are quite reasonable, especially considering their long service life. In addition, we have options for every budget. Sale of mosquito nets is our main specialization. We guarantee the highest quality of the products sold!
Benefits of mosquito nets
Mosquito nets are made of dark gray canvas, which is practically invisible to the human eye. Therefore, the presence of the grid does not irritate the eyes and allows the grids to remain invisible in any light.
Due to the resistance of the nets to ultraviolet rays, their color does not change even after many years of operation. This means that they will retain their aesthetic appearance for many years.
Caring for mosquito nets is elementary. From time to time they just need to be wiped with a damp cloth. Today, these devices can be installed on any type of windows and doorways, including attic, balcony doors, verandas.
Source: moskitniesetki.spb.ru
Velcro mesh
This type of protection against mosquitoes and flies is very effective, simple and convenient. The product closes the window opening and is held on the frame by lindens. Its installation is carried out in the inner part of the window sash.
The indisputable advantages of such a solution are environmental friendliness, resistance to bad weather, and ease of storage of the removed copy.
Today, a frame-type mosquito net is installed most often. There are two options for mounting this accessory for the window: through and outside.
The advantages of such a technological solution are quite significant: the mesh can be installed on a plastic and wooden window with a double-glazed window, as well as on an old Soviet one.
The external mounting option is used extremely rarely, the most popular is the internal one, on the opening sash.
When choosing a frame mosquito net, you need to pay attention to the quality of the frame in which the canvas is installed. The frame can be made of PVC or aluminum.
It is better to stop your choice on an aluminum frame, with a wall thickness of 1 mm (there are in the range of 0.7-1.0 mm) - this will be more reliable during operation. When choosing an instance, make sure that there are no various defects, depressions, depressions on the surface of its profile, that is, everything that during operation can serve as a collection of dead insects.
It is also worth paying attention to the handles with which the mosquito is framed. Such handles serve for comfortable installation / dismantling of the product in place. The material from which they are made is plastic (soft and hard) or metal-plastic.
The service life of the product depends on the type of material used for the manufacture of mosquito net handles: 2, 5, 10 years, respectively.
Roll (roller) mosquito
Perhaps, a rolled mosquito net, among others, is the most suitable option for installation on a window in an apartment.
Its design is convenient to use and allows you to open / close the web without spending excessive effort.
In addition to this, roll-type mosquito nets are widely used to close doorways from flying insects, as well as fluff.
Rolled mosquito net, in comparison with other types, has several significant advantages - reliability, elegant appearance and, most importantly, it is easy to operate.
In winter, the mesh, unlike others, does not need to be removed - the canvas will not be damaged due to exposure to low temperatures. Also, the mesh, when installed, for example, unlike the frame one, has practically no chance of falling out (for this you need to try very hard) and damage the neighbor’s recently purchased sports car.
The design of this type of protection implies the presence in it, in addition to the box and guides, of a handle, in fact, with the help of which the mosquito net is raised / lowered. The box also hides a spring responsible for automatically raising the net after a slight upward movement of the handle handle.
If there are skylights in the house, a rolled mosquito net installed on them can significantly facilitate the owner's access to the window - just raise / lower the net handle.
Caring for the roll mesh is as easy as shelling pears - it is enough to apply a damp cloth from the side of the room, or a vacuum cleaner with a slight draft.
The main feature of the retractable mosquito net is its use in conjunction with cold glazing of balconies and loggias, made according to the Provedal system or similar.
The design of the sliding mesh includes guides and small roller wheels that serve to move the frame with the canvas. The rails are attached to the window frame from the inside.
Sliding type mosquito nets in the upper part are equipped with pile, the purpose of which is to close the technological gap between the sliding doors and the net.
However, this design has a significant drawback - if it is impossible to fix the guides (for example, due to finishing the space), the installation of such a sliding system is not possible.
Mosquito net pleated
This type of protective mesh against insects in the direction of movement is similar to vertical blinds, but, unlike the latter, folds into an accordion. The pleated mosquito net is perhaps the only one with such a spectacular appearance.
It also has the advantage of being useful in providing protection against mosquitoes in large covered areas.
Mosquito net “Antikoshka”
Unlike other types of mosquito nets, the anti-cat protective product is able to withstand the weight of the animal’s body, thereby preventing it from falling out of the window, or making attempts to go for a walk on its own.
Also, the so-called "Pet screen" is able to resist damage to its canvas by claws - it will not leave scratches and holes made on it. This fact became possible due to the use of polyester-coated vinyl threads in the production of the "Antikoshka" net, and due to this, having super-strong properties.
The specification for the product speaks for itself: the "Antikoshka" sheet is seven (!) times stronger than the similar one used in traditional protective structures mounted on the window.
Due to the fact that the cell size of the mosquito net for cats is no different from the generally accepted one, its main function - protecting the room from the penetration of insects into it - is performed perfectly.
There are two options for the anti-cat mosquito net. In addition to being mounted on a window, you can order a variant with installation on a doorway - in this case, the passage of a pet to the balcony will be ordered.
In addition to all the properties described above, the "Antikoshka" network canvas is able to reflect part of the incoming ultraviolet rays, thereby contributing to savings on bills for the operation of the air conditioner in the heat.
Mosquito net “Anti-dust”
The purpose of modern mosquito nets is not only to provide protection against flying and crawling insects entering the house through the window opening.
Today, the market for such necessary additions to windows is ready to offer the end consumer a product that provides effective protection against the penetration of dust, poplar fluff and other flying allergens into the room. The name of such an accessory is the anti-dust mosquito net.
In addition to providing protection from dust, fluff, etc., "Antipyl" perfectly copes with its direct duties - protecting the premises from the penetration of insects.
Mosquito net "Antipyl" is made using heavy-duty material, so it is not afraid of strong gusts of wind, the harmful effects of precipitation. In addition, such a product does not ignite and is quite stable when working in bending.
Plunger mosquito net
The design of the plunger mosquito net resembles the design of a conventional frame one, and includes: an aluminum profile, a protective sheet, a frame seal and plastic corners. The main difference between the plunger mesh and other types is the method of attachment - it is installed on special metal plungers.
A plunger (translated from English: plunge - dive) is a spring piston, the length of which is significantly greater than its diameter. This piston is fixed in a through hole in the aluminum profile of the mosquito net.
What mosquito net to choose on the window to the apartment?
When choosing an anti-mosquito product for an apartment, it is necessary to be guided by the size of the cell and the overall performance of the accessory - the quality of the threads used, the strength of the fabric, etc.
Remember that the material for making mosquito nets can be as follows: nylon, fiberglass, cotton, polyester. Therefore, decide in advance what kind of material you would like to see in the future grid.
Standard mosquito net mesh sizes range from 0.6 to 1.2 mm. There is an opinion that the smaller the cell size, the better the protection against the penetration of fluff, dust and insects into the room.
This is partly true, but we should not forget that a network with a minimum mesh size does not allow fresh air to fully penetrate into the apartment through the window. This issue is especially relevant in the summer, when there is so little life-giving coolness in the apartment.
If you are going to install a mosquito net on a window in a house where there is a small child, then you need to carefully weigh this decision, since this product will not be able to withstand the weight of a leaning baby.
In this case, it would be advisable to open the window and put a mosquito on it at night, when the child is already sleeping. For daytime ventilation, the best option would be to install an air conditioner on the window.
Mosquito net care
In the case of an inappropriate attitude towards solving the issue of preventive care for the mosquito net, it can be ensured that it simply fails - defects may appear on the canvas that will affect the effectiveness of the protection of the product.
Each specimen has its own lifespan without care: some have one year, others have five - that's how lucky.
What needs to be done to make the mosquito net last as long as possible?
The most important thing is that when cold weather approaches, the net should be removed, since under the influence of negative temperatures, both the plastic of the frame and the canvas itself can begin to collapse.
It is also desirable to wipe the mosquito at least once a year with a damp cloth with soap applied to it. By observing these two conditions, you can significantly extend the life of your purchase.
Source: oknoudoma.ru
Mosquito net on the window - installation and DIY manufacturing: different types and cases
Nowadays, everything is technically improved, and the mosquito net is no exception. Modern mosquito nets are almost invisible, lightweight, durable, transmit light well and block the path of street dust.
Their design is quite repeatable at home; a do-it-yourself mosquito net can be made without experience and special tools in 2-3 hours. This means at least 2-3 times savings in money (multiply by the number of windows), but you need to know which window of which type of mesh is best suited and how to make it so that it immediately falls into place and lasts longer.
In what we will try to help readers.
Types of window grids
Manufacturers offer a wide selection of swing mosquito nets (pos. 1 in the figure below), sliding, pos. 2, pleated (accordion folding), pos. 3, and rolled screens, pos. 4.
The last two types do not have to be removed for the winter and they practically do not take up space in the room. But they all have 3 features.
Firstly, the technical complexity: hinges, locks, mechanisms are needed, and for installation - resp. production skills and special tools. Secondly, the high cost. A turnkey swing mesh is cheaper than 1600 rubles/sq. m in the Russian Federation could not be found.
Sliding pulls more by about 1900 rubles. per sq. m, and mesh-pleated and rolled for 4500 rubles. sq. m is fabulously cheap. But most importantly, all "mechanical" nets do not adequately protect against mosquitoes.
As you know, male mosquitoes do not suck blood, and mosquitoes need it for the maturation of eggs. Sensing warm-blooded creatures in the room, beautiful ladies of the mosquito family lurk nearby and patiently wait for the moment to invade. Mosquitoes need only 2-4 seconds to penetrate; movable grids open for a longer time.
Let only one individual fly in, but its annoying itching will not allow you to get enough sleep. Which is not easy in the summer heat and stuffiness.
Note: For a simple and inexpensive way to keep mosquitoes out of an openable meshed window or door, see end.
A reliable and inexpensive do-it-yourself mosquito net on a window is made with a fixed frame (pos. 5) or frameless, pos. 6. Frame mosquito net can be external, internal or inserted into the window opening.
Frameless grids are possible only internal. The cost of 1 sq. m of the factory frame mesh, without installation, is 700-1000 rubles / sq. m; the same amount will have to be paid for installation on any floor above the first.
A set of factory parts for self-manufacturing of a frame mesh costs 300-500 rubles. without a cloth. A fully finished frameless mesh for 1 window will cost the same amount. An option is possible for 80-100 rubles / window, but a big question, see below.
What to do? In general, the manufacture of a home-made mosquito net is carried out taking into account the following: Window frame material - plastic, wood. If the window is plastic, then the type of sashes to be opened is hinged, tilted, combined.
Type of household - private house, high-rise building. Floors of the building. Window opening frequency.
According to these conditions, the following are selected: the material of the mesh cloth - depending on local conditions and the presence of cats and small rodents in the house or nearby; mesh design - frame, frameless; if frame - its location in the opening: internal, external, plug-in; also for the frame mesh - frame design and materials for it; mounting method - both frame and frameless mosquito nets can be attached to the window in several ways; assembling a frame with a panel (if the mesh is frame) or sewing a frameless mesh panel; installation / installation of the grid on site.
Note: the mosquito net for plastic windows with tilting sashes is made exclusively as an external frame, unless the opening sash is completely removed for the summer.
cloth
The maximum allowable mesh size of the mosquito net is 3.7x3.7 mm; already crawl through the big mosquitoes. The minimum is limited by the conditions of air and light transmission.
Nets with a mesh size of less than 2x2 mm are suitable as temporary or in conditions of good ventilation, e.g. on the balcony; see also below. The mosquito net in the middle lane of the Russian Federation is usually taken with a mesh of 3x3 mm; in taiga places where small midges pester, with a mesh of 2x2 and even 1.5x1.5 mm. Grids with a mesh of 1x1 mm are used in very dusty places.
Mosquito nets made of fiberglass (fiberglass) coated with PVC (pos. 1 in the figure) are still in use due to their strength, but otherwise they are bad: light and air transmission is not important, because threads are thick.
PVC under the influence of ultraviolet radiation and dust soon collapses, the mesh becomes a dust collector and itself begins to dust with the smallest glass needles. Practically in the southern regions of the Russian Federation, fiberglass panels need to be changed every season.
Modern mosquito nets are woven from polyester (polyester) fibers. A grid with a rectangular mesh (pos. 2) is cheaper, stronger and better reflects (does not accumulate in itself) street dust, but it does not let light and air through.
In places where small bloodsuckers (midges, cobwebs) are common, and the Sun does not indulge in bright radiance even in summer, it is better to make a grid on the window from a material with 6-coal cells, pos. 3. A cloth with 6-angled meshes 1.5 mm in diameter gives the same resistance to light and air flows as a wicker cloth with rectangular meshes 2.7x2.7 mm.
The mesh size and type of weaving is not always known to sellers, especially on the Internet. Most often they offer a grid with rectangular cells of the Standard, Antidust and Antikoshka brands, pos. 4:
Standard - mesh 3x3 mm, material of normal strength. Anti-dust - mesh 1x1 or 1.5x1.5 mm, material of increased wear resistance and strength. The weaving of the canvas is smooth: dust settles little on the mesh, but is mainly reflected back by small air turbulences.
Designed for southern treeless areas with high insolation and dust content in the air. It can replace the "anti-nasal" mesh with a 6-coal fine mesh in the taiga and tundra, but the light transmission for high latitudes is at best satisfactory.
Antikoshka - a mesh of 2.5x3.5 mm or so, a material of increased strength. Light and air transmission is satisfactory for middle latitudes and to the south. Doesn't save from nastiness; the cell cannot be reduced, because otherwise the cat will break its claws.
About anticats
Plastic mosquito net - anti-cat withstands the antics of medium-sized and violent cats and small rodents; those, by the way, climb vertically no worse than their pursuers.
It is advisable to place a plastic anti-cat on the first floors, but if you have a domestic cat, then you need to put a steel one with a rare mesh on top of the mosquito net from the inside, see Fig .; the same is done outside if there are many stray cats in the area.
Firstly, domestic cats are on average larger and stronger than street cats, and their claws are sharper, because wear out less. Secondly, the rule rather than the exception: a well-behaved domestic cat, having received a mosquito net at its disposal, throws its scratching post and begins to tear protection from mosquitoes for how much in vain.
Often at the same time tearing off the claws. What colour? The clarity and contrast of the picture outside the window when viewed through a white mesh, even with a very rare large mesh, drop noticeably, but from the outside you can see through it well.
The point here is the so-called. diffraction distortion of the light flux. Therefore, it is better to take a mosquito net in black, dark gray or dark brown. When viewed obliquely, the moiré pattern will be more noticeable on it, but the outward visibility will generally improve, and from the outside to the inside it will worsen even more.
Framed or not?
Well-designed frameless mosquito nets are either weakly held in place or do not allow for frequent removal, so their use is limited (see below for more details). There is another option "superbudgetary", up to 100 rubles. on the window, frameless mesh: regular plastic window seals are removed, a panel is inserted into their grooves and fixed with a linen cord; cm.
But, if PVC windows with a rubber seal are inexpensive, then, firstly, it turns out that it is impossible to pull out a seal that has stuck for 2-3 years without tearing it. Secondly, if the windows are new and the sealant is nevertheless removed, then after the same 2-3 seasons it stops sealing, it starts to blow and flow through the window.
Repairing a window then costs much more than the materials for the frame mesh, up to the need to replace the window frame. Therefore, next we will deal mainly with frame mosquito nets, and we will return to frameless ones when it comes to where they are appropriate.
Fastening
When choosing a method of fastening and installing a frame mesh, please note: if the mesh is external, and the window is under warranty, then the latter “burns out”, unless the mesh is ordered on a turnkey basis from the window manufacturer. The reason is that fasteners will have to spoil the frame.
It is possible to attach the frame mesh to the plastic window in 3 ways (see the figure on the right); to wooden - by them with some features, see below. Fastening with plungers (spring-loaded rods with heads, on the left in the figure) is the easiest: the heads are retracted, the mesh is put in place, the heads are released, and the heels of the rods jam the mesh in the opening.
On the rods, the mesh can be placed both from the inside and outside, however, fastening mosquito nets with plungers is not very common. reasons: The mesh is weakly held - a strong wind squeezes it inward or, externally, generally blows it away.
Large concentrated loads fall on the heels of the plungers; the mesh is ruffled by the wind, and the heels of the rods are eaten away in the frame from any material of the hole, which is why the guarantee for the window disappears.
The holes for the rods weaken the frame, and from the same alternating wind loads, it breaks faster than a solid one. Mosquito net plows are not cheap, and their installation requires special tools.
Frames of outdoor mosquito nets are usually attached to window frames with Z-profiles, in the center. Then the nets themselves turn out to be as compact as possible and take up a minimum of space during winter storage. But, firstly, fixing a mosquito net with Z-profiles on the upper floors with your own hands is simply life-threatening: you have to lean out halfway out the window to mark and install the fasteners.
Secondly, drilling of the window frame is required, which voids the warranty on the window or, if it is wooden, rot occurs. Fastening the mosquito net with staples, on the right in the figure, is similar to fastening with Z-profiles, but the staples are placed on the mesh frame, which can also be internal or external.
The thickness of the mesh package with staples during winter storage swells by half or more; grids in storage must be shifted with cardboard so that they do not tear the panels to each other with staples, but the window frame is not damaged.
Framed mosquito net with staples is the most preferred option for making your own hands, especially if the window is wooden and / or the frame of the net is made from improvised materials, see below.
measurements
Preparation for the manufacture or purchase of a frame mosquito net begins with measurements. If the window is wooden, then measure the width and height of the light opening in several places; the smallest value is taken as actual.
Suddenly you order a grid in a wooden window for self-installation, you need to find out exactly from the manufacturer what is there, where and how to measure, because. wooden window designs are varied.
For a mosquito net on Z-profiles into a plastic window, you also need to measure its light opening in 3-4 places in height and width (on the left in the figure) to make sure it didn’t lead? Then you need to measure the same width and height of the opening between the inner edges of the seals (in the center); if the opening led more than 2 mm - in the narrowest place.
Finally, the masters will be grateful to you, and the grid will immediately fall exactly into place if you measure the width of the slopes O and the height of their sills P, on the right in Fig.
Measurements for braces
Left to track. rice. the names of the parts of the mounting bracket for the mosquito net are given; this will be of use to us in the future. And on the right it is shown how to calculate the dimensions of the profile from the measurements of the window frame and adjust the dimensions of the grid frame; the width of the bracket is taken from 12 mm.
At the same time, the light opening of the window is slightly reduced, but it is not necessary to use U-shaped brackets to make the mesh frame flush with the window inside: the fastener heads will spoil the window frame. The paws of the upper brackets are made longer than the lower ones (see below); the height of the bracket shelf should be equal to the height of the slope threshold with sealant.
How to put ready
Let's say you decide to save only on the installation of the grid. Self-installation of a mosquito net on a plastic window is possible in several ways. The most reliable - outside in the corners, pos. 1a next. rice: no wind will blow the mesh.
However, mosquito nets can only be fixed in this way in private homes or if the supplier of new windows offers nets as a gift. The fact is that marking the holes for the mounting brackets with your own hands in this case is possible only in place, because. not to stray is necessary in 2 directions at once.
If the windows are not yet in the walls, then grids are placed on their frames, drilling is marked for fasteners, corners are placed, and only then windows are mounted in wall openings. It is impossible to do this on the already mounted windows of the upper floors without experience of working at height and climbing equipment, and from the first floors the grids can simply be stolen.
Note: Outdoor anti-theft mosquito nets are often supplied with internal twist latches.
But, first, the tongue of the latch spoils the frame over time (do not forget, the wind ruffles the mesh). Secondly, the tongue of a simple latch is simply removed from the outside with a thin nail or wire inserted through the mesh, and latches with locks are expensive. Fastening with Z-profiles is described above and is shown in pos. 1b fig.
Outside, on the upper floors, it can be done, albeit at the risk of life, or with reliable insurance with a fitter's belt with a halyard. But a strong side wind can move the net, immediately turn it inside out and break it.
Still, fastening with brackets is more reliable, pos. 2. The frame mosquito net on brackets, external and plug-in, differ not only in the size of the net frame, but also in the height of the mounting brackets. In the designations of typical profiles, it is given, in mm, by the last 2 digits; for typical plastic windows - acc. 13 and 7 mm.
Therefore, before ordering the grid, you need to measure the height of the window slope threshold - all of a sudden it is not typical. Then you need to inform the masters to select the desired profile, otherwise the mesh will either hang out or not fall into place at all.
Under an atypical window, the nearest larger standard size is taken and the racks with crossbars are cut to size. For installation on Z-profiles, the dimensions of the frame on the inside must be equal to the dimensions of the light opening; about installation of a grid on brackets see above. The width of the profiles, as a rule, is from 60 mm, so that it is enough for mounting on brackets.
An additional transverse beam - impost - and fastenings for it, are ordered optionally if the height of the grid is more than 1.3-1.5 m. In swing and sliding grids, imposts are placed every 60-80 cm in height.
The material of profiles and fasteners is of some importance. Steel corners (in the center in the figure) are a little cheaper, but rust over time - the PVC coating wears out. In addition, the metal rubs the plastic of the racks and cross members, causing the frame to become loose.
The plastic corner connectors of the mosquito net frame (on the left in the picture) are good in every way. As for the actual frame profiles, they are made of PVC (cheaper) or propylene (more expensive). PVC is less durable and becomes brittle after 3-4 seasons from ultraviolet radiation.
Propylene frames of mosquito nets serve for 10 years or more, you only need to change the canvas in a timely manner as needed. The frame on steel corners is fastened with through bolts. The frame on plastic corners is fastened either with self-tapping screws or standard latches; You can also reinforce it with hardware to serve longer.
For laying the mesh panel in the frame, see below. From something Plastic profiles for frames of mosquito nets are also sold in long lengths of 3 and 6 m. If the nets need to be put on several windows, then their purchase and connection into frames with improvised means is the best option in terms of reliability and minimum costs.
In this case, you need to purchase a special elastic cord for laying the mesh in the grooves, pos. 7 in fig. The surface of the mesh cord is ribbed; when rolling it into the groove with a roller, the ribs grab the threads of the mesh longitudinal in this direction, ensuring its more uniform tension.
The frame of the mosquito net is completely “out of anything” and is obtained from boxes - plastic cable channels 10-60 mm wide. For the frame of the outer mesh in Z-profiles, you need to take boxes of approximately square section (marked with red arrows in position 1), so the frame will be stronger and stiffer.
For frames for landing on brackets, boxes are better suited, oblong in cross section (blue arrows). The frame is assembled on ordinary flat steel corners, pos. 2 and 3. The frame of cable channels is bolted by removing the covers of the boxes.
For a frame made of special profiles, you need to take corners with a thickness of 1.5 mm and fasten with metal screws - there is no cover, you can’t put a nut with a spring washer on a bolt. Impost, if necessary, is made from a piece of cable channel, gluing its cover with strong glue (Mount Moment, Titanium) and clogging the ends with wooden plugs.
An impost is fixed to the frame with through wood screws. Laying the canvas The finished frame is laid horizontally with the groove or open gutter of the box up. A mesh cloth with an allowance of 3 cm (preferably 10-15 cm) is applied, straightened.
If the allowance is large, the canvas will lie more evenly when the wings of the allowance, straightened, are pressed along the contour with small weights. Further, if the frame is made of a special profile, a cord is laid on the canvas above the groove and rolled with a roller until it is completely pressed. Excess mesh is cut with a knife, leaving approx. 1 cm above the groove.
If the frame is made of cable channels, then the covers of the narrow sides are first placed on the superimposed and straightened mesh. You need to press them until they snap into place immediately along the entire length, preferably in 4 hands. Then long lids are also applied and pressed down. If you act carefully and consistently, the mesh will be stretched as evenly as the branded one.
Pens
You can't put an outdoor mosquito net in place without handles.
Their cheapest option is soft and thin plastic, on the left in pos. 4. These are placed in place before the mesh is applied and pressed into the grooves of the profiles along with it with a cord. Cheap, simple, but thin handles are often torn, and when replacing the cloth, you also have to change the cord - it flattens over the handle, and this section of it will not hold a new mesh.
In addition, soft handles cannot be placed on a cable duct frame. Therefore, it is better to put stronger handles on the frame of the mosquito net, attached with self-tapping screws, to the right in pos. 4. Note: for the sake of penny savings, do not put one furniture handle on the impost - the frame will soon break.
Staples
Plastic brackets-holders of the outer mosquito net (pos. 6a and 6b) do not damage the window frame, but are rather fragile and often break in strong winds; the mesh dangles in them. Steel spring clips (item 5) hold the mesh to the window more securely and tightly, but can scratch the window frame, even if covered with plastic: thin soft PVC wears out quickly.
The best way to make the mosquito net spring bracket completely secure and secure is to pull a piece of heat shrinkable tubing (HERE) over it and heat it with a household hair dryer at maximum or carefully turning it over a gas flame.
The bracket is tightly covered with a layer of durable elastic plastic with a thickness of approx. 1 mm. To install a mosquito net on brackets in a wooden window, this is the best option.
Frameless Frameless mosquito nets are fixed in place with either Velcro tape - burdock Velcro - or soft magnetic strips, the same as those inserted into refrigerator door seals. Each of these fastening systems has its own advantages and disadvantages and its own scope.
Velcro
Velcro holds the mesh very tightly, but it is not so easy to peel it off. A half of Velcro tape with hooks is glued to the window frame from the inside. If the window is plastic, then the hooked half of the Velcro is glued along the slope inner contour from the seal. The fleecy half of the Velcro is sewn along the contour of the mesh panel.
For winter storage, the cloth is rolled up; if a hooked half of Velcro were sewn to it, then the roll would seize tightly and in the spring it would be impossible to unfold it without damaging it. In the use of Velcro mosquito nets, there are still unpleasant circumstances: they sit too tightly in place. Try to peel off the tongue of the Velcro shoe, where it is only 1-4 square meters. cm.
And if the area of adhesion is somewhere 100 times larger? It is necessary to glue the "burdock" side to the window frame with a very strong glue, the remnants of which cannot be removed without damaging the window frame. And this does not guarantee that on the 2nd - 3rd mesh removal, the pasted half of the Velcro will not stretch along with it.
Therefore, a mosquito net with Velcro is most often placed on balcony windows, in which the net has been standing all season. The thin mesh does not interfere with closing the window sash. Note: not so long ago, a modification of burdock Velcro appeared on sale - burdock buttons. To install a frameless mosquito net on a balcony window, this is perhaps the best option, see next. video:
magnets
Tape magnetic holders are produced single-pole, for fastening to steel, and bipolar, for fastening to a non-magnetic base. Mosquito nets are made on a single-pole magnetic tape, for example, in car windows; at a picnic or in the country, it is better to leave them open so that the car does not turn into an oven.
The magnetic tape is sheathed with a drawstring (a long narrow sleeve) made of thin, durable and non-rotting fabric: thin raincoat fabric, nylon calender, and sewn along the contour of the cloth, which remains only to be applied in place.
The mesh is held on magnets rather weakly, but in a small opening it is quite reliable, and does not damage the base at all. Bipolar magnetic holders adhere more strongly and are therefore suitable for windows and doors. For ready-made kits (which are more expensive), the polarity of the tapes is marked, and one of them is already pasted on Velcro tape.
It is glued to a fat-free base, and the conjugated magnet is sewn in a sleeve along the edge of the panel, see above. Bipolar magnetic Velcro can be made from a pair of unipolar and double-sided adhesive tape.
The polarity of the tapes must be marked so that when the panel is installed, they stick together and do not bounce off each other. If the error came out with the polarity, then, in general, it's okay: we turn the panel over, and it holds, only weaker.
A mosquito net on magnetic holders is perhaps the best option for going to a country house or temporary residence, say, at a recreation center. And at the door
Magnetic strip holders allow you to make the mosquito net on the balcony door impervious to mosquitoes, but easily passable for people. To do this, a pair of panels (see the figure on the right) at the top and on the sides are attached to the door frame with Velcro, and along the bottom and the seam is fastened with a bipolar magnetic tape.
There is one trick here: along the seam, the magnet should be fastened in segments of 10-15 cm after 20-25 cm, pos. 2 in fig. The edges of the seam should overlap with the width of the magnetic tape. Then a person will simply pass through such a veil, even if he carries something with both hands, but behind him it will collapse tightly faster than the most nimble mosquito has time to fly in.
With the onset of the long-awaited warm days, mosquitoes and midges come to life. It is very difficult to hide from them. They penetrate into the slightest gap, strive to get to the person as soon as possible. Only a mosquito can stop them. It will also become an obstacle for poplar fluff, dust, etc. Let's figure out how to install it on a plastic window yourself.
Selection and installation of a mosquito net
The best way to protect your home from annoying guests is a mosquito. It completely covers the frame, preventing the penetration of insects inside.
Types of mosquito nets
- Framework. This is a frame assembled from metal-plastic, on which a mesh fabric is stretched. The finished structure is mounted on the outside of the window with plungers or Z-brackets. This is an economical and quite convenient option.
- Roll. The protection is made as an analogue, only instead of a fabric a plastic mesh is placed. The roll is attached to the top of the frame. If necessary, the edge is lowered and fixed. Easy to use, the price is higher than analogues.
- Swing. It looks like a frame, but the frame is reinforced. One side of it is placed on hinges, after which the frame can swing open and close by snapping onto a magnet. The design is more often chosen for doors on.
- Sliding. A constituent element of sliding systems. This is a frame moving along the guides, on which the mesh panel is fixed. Its dimensions correspond to the sash. When one of them opens, the canvas moves and closes it.
Despite such a variety of anti-mosquito elements, frame products are most often chosen.
Take measurements
- Fully open the sash.
- We measure the width of the opening from one seal to another.
- Similarly, we measure the height of the opening.
In order not to be mistaken with the sizes, we must measure in several places. There may be slight discrepancies. The obtained values are recorded with an accuracy of millimeters.
Choose mounting method
An important point: the choice of attachment. Plungers are placed on the frames, they are also rods or brackets. The latter option is much more common. In this case, the mosquito is placed on the outside of the window. It is inserted into brackets shaped like the letter Z. A significant drawback is that the product can be easily removed from the street. Therefore, such fasteners are placed above the first or second floor. On the lower ones, grids are installed on the plungers. They are also attached from the outside, but the rods that fix the product in place are located on the side of the room. Thus, it is impossible to remove the protection from the outside.
The difficulty lies in the fact that the frame must exactly repeat the light opening. It is almost impossible to do this, there are always small gaps. They can be used by insects. Therefore, a special brush is attached around the perimeter of the frame.
Made according to the specified dimensions, it is issued to the customer along with the fasteners that he will install on his own. Let's look at two possible options.
Sequence of work for a staple in the form of the letter Z
The kit comes with four brackets. Two of them with a shelf side of 25 mm, two with a side of 40 mm. Those that are larger are placed on top. To work, you will need a drill, a 2 mm drill, a screwdriver or just a screwdriver, two self-tapping screws with a screw for each bracket.
- We open the sash. Outside, on the bottom of the plastic frame, lay 30 mm down, draw a line. We will install brackets on it.
- From it we set aside the height of the mosquito, add 18 mm, draw a line. If it is possible to work outside, the easiest way is to attach the part to the intended bottom line, mark the top edge. Add an allowance, draw a second line.
- We outline the areas where we will mount the brackets. We retreat 10 cm from the edge of the light opening to the left and right. We make marks.
- We apply fasteners to the intended point so that the edge of the shelf is on the line. Mark where the holes should be. We do the same with each bracket.
- We drill holes. We put the brackets, fasten them with self-tapping screws.
It remains to put anti-mosquito cloth. He is taken by the handles, slightly turned to the side, taken out of the sash. Then lead into the upper brackets, align. Raise, insert into the lower mounts, lower a little.
The sequence of work for the corners
Installing a mosquito net on a plastic one is also done on the corners. Like staples, they are attached to the outside of the window frame. Larger fasteners are installed on top, smaller ones on the bottom. The elements are fixed with self-tapping screws. The marking and installation process is very similar to that described above. There is only one difference. The clamps "hold" the mosquito by the corners, so precise marking is required.
The lower and upper bounds are outlined in a similar way. Then determine the middle of the opening. From it to the right and to the left lay half the width of the mesh part. The distance between the inner centers of the corners will be equal to the width of the mosquito plus 0.2 or 0.3 cm for free fixation. Installation of the frame in the corner mounts is carried out in the same way as in the brackets.
We figured out how to attach a mosquito net to a plastic one. This is not at all difficult, especially if you order a product according to your size from a company specializing in the production and installation of window systems. It remains only to put up protection that will block the path of annoying insects.
As soon as hot days come on the street, one wants to open wide all the windows in the house so that fresh air displaces the stagnant stuffiness. But here's the problem: along with fresh air, annoying insects joyfully fly into the home to spoil our mood with their bites and buzzing.
The best way to keep them out of your territory is with a mosquito net. We will talk about the rules for installing it on a plastic window in this article.
Mosquito net: how it works, types
This simple device will not only act as a protection against annoying insects, so you do not have to spend money on fumigators and other not-so-useful chemicals. The mosquito net will not let street dust, poplar fluff and plant pollen into the house, which is very important for allergy sufferers. In addition, you can not worry about the safety of your pets - cats, dogs and birds when the window is open.
Note! There are many cases when cats and dogs, trying to jump out of an open plastic window, got stuck between the frames and died from asphyxia. By installing a mosquito net, you can save your pet not only health, but also life.
Structurally, such a grid consists of the following parts:
- profiles: frame, transom and corner;
- connecting corners;
- fastening cord;
- 4 holders (z-mounts) made of metal or plastic.
Using a mosquito net, you will be convinced of the mass of its advantages. The first is convenience. At the right time, you can easily remove this design, and if necessary, insert it back without much hassle. The mosquito net does not require careful maintenance, as it is rubbed with a sponge and washed with soap and water.
The second is the discreet appearance of the grid, its aesthetics. Small holes in the material make it translucent, so the view from the window is not obstructed, enough sunlight and fresh air enter the room. Rain water from the street through such holes will not leak.
And the third - the design of the mosquito net consists of aluminum and fiberglass. This means that it is highly durable, resistant to mechanical stress (tearing, stretching, bending tension) and does not fade in the sun. But nevertheless, the net is flexible and compact enough that you can roll it up and put it in a closet for a while.
The most common types of fastening mosquito nets
Taking into account the features of installation and use, mosquito nets are divided into several types. Let's consider them in more detail.
- Frame mesh - the simplest design, affordable, and therefore the most common. It is presented in two versions: removable and sliding. This is your option if you are not going to open the grid often. The mesh for windows that are too large is often reinforced with a plank in the center. There is another type of frame mesh - plunger. It is mounted in the window opening, and not attached to the corners.
Frame mosquito net - the easiest and most affordable option
- Velcro construction (sometimes tape) is very easy to use. It is mounted on the inside of the window sash, and can be easily removed when needed.
In order for such a mesh to stick well to the window, you must first clean the surface of dust and load.
- The roll mosquito net is a relatively new invention. It consists of the mesh itself, rolled up and attached to a guide profile with a transverse bar equipped with handles. The principle of operation of the device is the same as that of roller shutters: when you open the grid, it goes inside the box located above the door. This type of grid is very well suited for large windows.
Rolled mosquito net, or rollet
- The pleated mesh resembles a rolled mesh by the principle of operation, it only gathers into an accordion, moving in a horizontal direction. These meshes are so good in appearance that modern designers often offer them to customers not only as protection, but also as an interior element. This design can be made in any color and decorated with drawings or other decorative elements.
Pleated mosquito net can be a decoration for your window
- "Antikoshka" - this design is useful to you if there are pets in the house. The net is made of very strong threads that are resistant to any damage and is equipped with an additional fastening for increased safety. No cat can hurt her. And it is not necessary to remove this mesh for the winter - it will perfectly withstand snow and frost.
Mosquito net "Antikoshka" will withstand the pressure of your pet
Types of fastening on plastic windows
This design is usually fixed to PVC windows with one of four types of fasteners.
- Plunger fastening - experts position it as the most reliable, but at the same time it is more expensive than other options. Plungers can be mounted in windows of any type, they are most resistant to wind. The plunger is a metal pin with a spring-closer, adjustable in length. A mosquito net with such a mount is easy to install and remove.
- Plastic corners are a popular type of fastening. They are installed from the outside so imperceptibly that they do not catch the eye, which means they do not spoil the design of the windows. The mesh can be easily removed and will not interfere with closing the window.
- Corners made of metal, z-mounts are not as reliable as plungers. They should be tightly fitted to the frame and fixed on it additionally from the inside.
- Mounting "Flag", unfortunately, is not reliable compared to previous options, but cheaper. Fasteners are small plastic hooks that fix the mesh. The disadvantage of such an attachment is its low resistance to external influences: it can easily be torn off by a strong gust of wind.
Mosquito net mounts: plungers, flags, corners and z-mounts
Installation Instructions
To independently install the mosquito net, prepare the tools:
- screwdriver or drill;
- thin drills;
- riveting tool;
- screwdrivers;
- ruler, tape measure.
Fasteners are supplied with the assembly. But you need to be sure to specify this when ordering and check before purchasing products.
Installation on metal brackets from the inside
This method of attaching the mesh to PVC double-glazed windows is considered the simplest and safest. With the help of aluminum rivets, the hooks are baited onto long strips.
- Hold the product by the side handle and wind the top bracket over the window sill.
- Raise the mesh all the way up, hook the lower hooks on the frame ledge.
- Seat the mosquito sheet down to the very end and align with the window opening.
Install the mesh and fasten it to the brackets
Fastening the canvas from the outside
This method is reliable, besides, with such a mount you will not damage the rubber seals. But do not forget to follow the safety rules, because you will have to lean out of the window outside to screw the corners.
Video: how to install a mosquito net on the corners
Mounting on plunger mounts
If mounting on conventional brackets is not possible, this method is used. As a rule, a protective grille can interfere. Or there is not enough space on the frame to place the brackets. Since the plunger mesh should be placed inside the opening of your window, and not overlapping, measurements are taken in strict accordance with the perimeter of the frame.
Roll mesh (roller)
The most effective way to protect against insects and dust from the street. The system is fixed above the window.
- Free up the attachment point: remove the plastic or aluminum frame from the mesh.
- Having attached the net to the window, mark the place where you will fasten it, and fix it.
- Open the covers on the slats to get to the fasteners.
- Along the entire length of the perimeter of the window frame, mark the installation locations and mount the strips as evenly as possible. Tuck the mesh under them, then fasten the covers of the slats back.
The installation of the roll mesh begins with the installation of the box on the upper window frame
Video: how roll mosquito nets are attached
What about timber framed windows?
So far, not all apartments and houses are equipped with PVC double-glazed windows. How to protect yourself from the invasion of insects if you have windows with wooden frames? We offer you several options.
The order of installation of the mosquito net is determined by its design. The complexity of installation depends on the location, method of fixing and features of the window or door.
Tools used:- Screwdriver or drill;
- Thin drills;
- riveting tool;
- Screwdrivers;
- Line, roulette.
The mesh package usually includes fasteners, which is discussed when ordering and checked before purchasing the product.
Fastening to internal metal brackets is a simple and safe way to fix a removable frame mesh on. Hooks are mounted on long slats with aluminum rivets. Installing the mesh in the opening is performed as follows:- Using the side handles to hold the product, the top brackets are wound behind the window influx.
- The grid rises all the way up, the lower hooks are hooked on the frame ledge.
- The mosquito cloth is planted down to the end and aligned in the window opening.
Mounting order:
- The bottom brackets are fixed with self-tapping screws, placing them at a distance of 20 mm from the edge of the opening.
- The height of the grid is measured, 10-15 mm is added, the mounting points of the upper brackets are marked.
- The corners are screwed at an equidistant distance between themselves and from the borders of the window opening.
- A mosquito net is installed: slipping it all the way into the upper fastener and leading it into the lower corners, the product falls into place.
Mounting on plungers:
- Places for pins are prepared in the grid frame: first, four holes are drilled with a diameter, like the threaded part of the plunger, then the holes in the outer walls of the profile are expanded to the size of the retractable tip.
- Pins with springs on are inserted into the frame and tightened with tips.
- The grid is tried on in the opening, marks are placed opposite the plunger outlets.
- Holes are drilled into which mating pin sleeves are installed.
- A brush seal is glued onto the mesh profile.
- One side of the product is placed by plungers in the reciprocal holes.
- Squeezing two tips from the opposite side, the mesh is inserted into the opening and fixed.
- The doorway should be blocked by 10 mm on each side.
- The minimum gap between the frame and the upper slope is 21 mm.
- Sufficient space is provided around the self-closing mechanism for its adjustment.
- The magnetic latch is attached to the opening, and the striker is attached to the frame profile.
- The number of magnetic latches is selected based on the height of the door.
- Cutting the body and shaft with a mesh to the required dimensions.
- Preparation of guides and fixing strips.
- Assembly of parts of the body and gearbox.
- Marking and execution of mounting holes.
- Fixing the system to the window frame.
- Operation check and adjustment.
It will be a simple matter to install a conventional frame or. More difficult, but also affordable to do it yourself, will be the installation of a rolling mosquito system.