Reinforcement mesh weight. Reinforcement Mesh Weight Area Reinforcement Mesh Calculator

Steel mesh is most often used to reinforce various structures. It is made from a metal thread of different diameters, it can have additional protection against corrosion. The low specific weight of the reinforcing mesh simplifies its installation and transportation.

The quality of this product

The characteristics of welded meshes depend on their purpose:

masonry and road;
strengthening of thermal insulation and glass.

Use low carbon wire. Rods of different lengths are welded by resistance spot welding. Corrosion protection is carried out by polymer coating or galvanizing, which is carried out in several ways:

galvanizing rods before welding;
electrolytic method;
hot coating.

Reinforcement without a galvanized layer is called light.

On the welded mesh for glass, thermal insulation, corrugation is applied from 1 or 2 layers.

Characteristics of welded metal products, according to technical conditions 14-4-1284-84

The mass is calculated depending on the size of the cell, the distance between the axes of the wire, the presence of galvanized:

Tables for converting grid area to mass

Reinforcing metal products are used for the following purposes:

reinforcement of reinforced concrete products;
strengthening of the banks;
roadway reinforcement;
in the household (making a fence for poultry);
fencing of territories.

The mass of 1 square meter of metal products depends on the length, width of the cells, cross-sectional area of the bar, and the specific gravity of the material. The bar size Ø ranges from 0.5 to 8 mm.

Form of release of products from welded fittings:

rolls;
cards;
panels.

The dimensions of the reinforcement mesh depend on the form of release. Products in cards reach a length of 6 m. The maximum width is 2 m, the minimum is 35 cm. Two-meter panels have a width of 2.5 m. Rolls are produced with a width of 0.2–2 m and a length of 15–118 m.

The sizes of the windows depend on the purpose, there are 6 * 6–20 * 20 cm. There are rectangular ones with different dimensions.

Standard TU 14-4-1284-88

Products according to these specifications are manufactured with square and rectangular windows.

From a light, with a large cell size, cages are built to keep birds and fur-bearing animals. It is used to strengthen reinforced concrete structures, making them stronger. But for this, the metal mesh must be of high quality. You should not use a product in which the welding points are located not at each point of contact of the rods, but through one. This technology significantly reduces quality. This can affect safety.

Welded fittings, according to specifications 14-4-184-93

The mass of 1 square meter of metal with the same rod thickness will be the greater, the smaller the cell wall size:

Parameters in centimeters	Metallic thread type	Weight 1 sq. meters in grams
1,6*2,4	WITH	2480
1,6*4,8	WITH	1990
2,4*2,4	WITH	1970
2,4*4,8	WITH	1500
3,2*4,8	WITH	1250
1,6*2,4	O	2810
2,4*2,4	O	2220
1,6*4,8	O	2240
2,4*4,8	O	1710
3,2*4,8	O	1410

Note:

WITH- light type.
O- galvanized type.

For construction work, rods with a diameter of 0.6, 0.8 and 1 cm are used. The higher the load on the structure, the stronger the mesh should be, the larger the wire diameter.

The size of the cell depends on the material to be strengthened. To fix the brick structure, a wall length of 5 cm is sufficient.For a cement screed, these indicators will not be enough, you need to use a smaller markup.

ВР-1 metal products from В500С fittings

Calculations were made for cutting 2000 * 6000 mm:

Reinforcement products are used as a base for marble masonry. It makes the structure stronger, more durable, and prevents the formation of cracks.

For fencing plots, it is advisable to take galvanized products that are not susceptible to weather factors, therefore, they are much more durable and have a better appearance.

Comparison table of class B500C with reinforcing bars of other classes

You can find out the mass of 1 meter of metal products from reinforcement using the formula 0.785d 2, where d is the diameter of the metal thread, 7850 is the specific weight of the wire in kg / m 3.

Reinforcement mesh weight

The concrete casting used to create the foundations is itself a fairly solid structure. However, its strength is great only in one direction - namely, concrete resists pressure well.

But the concrete foundations can be affected by loads in other directions. For example, it can be influenced by bending, twisting, and so on. The soil is a heterogeneous substance and, when frozen, can change its structure and volume, expanding in different directions. In order to give the concrete casting strength and resistance to impact in any direction, a metal power frame is introduced into the body of the concrete casting.

The metal frame in concrete castings is used not only in the construction of foundations. It is also created during other concrete work, for example, when building stairs or when creating a leveling cement-sand screed.

The metal frame of a concrete casting can be created in various ways. So, a lattice frame can be created from metal rods that are connected to each other at intersections. The rods can be fixed with knitting wire, clamps or electric welding.

An excellent solution when forming a metal frame can be the use of a reinforcing mesh.

Reinforcing mesh. Characteristics and examples of use

Reinforcing mesh is formed from metal wire or from reinforcing rods of a larger cross-section in industrial production. This achieves the accuracy of the grid spacing, which has a positive effect on the overall quality of the reinforced concrete structure.

In the process of its manufacture, wire sections or reinforcing bars are laid out with a certain step, and then at the intersections they are fixed by electric spot welding.

Reinforcement mesh is widely used in the construction industry, both for exterior and foundation work, and for interior interior work. Layed in several horizontal layers in the foundation and connected by vertical bridges - the reinforcing mesh becomes an excellent load-bearing frame for reinforced concrete casting. Reinforcement mesh, laid in one layer on the floor surface, can become the basis for a floor screed or for fastening a system of underfloor heating with a liquid heat carrier. In addition, complex, strong reinforced concrete structures, for example, entrance stairs, can be formed using reinforcement mesh.

Reinforcement mesh - photo

Reinforcement mesh types

Reinforcement meshes can be classified according to several parameters. First of all, the reinforcement mesh can be divided into types based on the thickness of the source material used:

If the reinforcing mesh is made of a relatively thin metal wire, then it is conventionally called "thin"
In the event that the reinforcing mesh is made of a thick metal bar, then it can be conventionally called "thick".

In addition, the mesh can be produced with varying degrees of precision.

Ordinary welding accuracy, which is quite suitable for outdoor construction work, and reinforcing mesh with increased accuracy can stand out. The accuracy of welding of reinforcing mesh elements is indicated by numbers after the letter "P" in the marking.

Reinforcement mesh sample

Separately, it should be said about the form in which the reinforcing mesh is supplied from industrial enterprises. Depending on the thickness of the elements used, the mesh can be supplied from the factory in the form of flat plates or in the form of rolls.

In addition, depending on the purpose, the reinforcing mesh can be produced with various mesh configurations. They can be rectangular or square.

Reinforcement mesh sheets

Features of the use of reinforcing mesh

Reinforcement mesh can significantly reduce construction time using concrete castings.

With the classical method of forming a power frame, it is created from separate metal rods. At the same time, the creation of a spatial frame seems to be a rather difficult task. Each point of intersection of the reinforcing bars must be held together.

The fixation of the intersection of the reinforcing rods can be done using knitting wire loops. It folds in half, wraps around the intersection and twists using a pointed hook or special automatic devices.

Naturally, such a fixation can take a lot of time and effort. Therefore, in a number of cases, when carrying out foundation and general construction work, it is advisable to use a ready-made reinforcing mesh.

Calculating the weight of the reinforcement mesh

Calculating the weight of a reinforcing mesh can be useful for you to determine the total weight of a building structure, and for calculating logistics - that is, ways of delivering building materials to the construction site of the building.
To calculate the weight of the reinforcement mesh First of all, it is necessary to know the diameter of the used metal rod or wire, the pitch between the wire or rods and the configuration of the cells.
So, the step between the wire or rods can be from 5 to 25 centimeters. When creating a reinforcing mesh, both a wire with a diameter of 3 millimeters and a reinforcing metal bar with a diameter of up to 12 millimeters can be used.
Mesh labels use standard notation to help you calculate the weight of the reinforcement mesh.
So, if the reinforcement mesh is marked "150x150x5", then this means that this product has a square cell of 15 by 15 centimeters and is made of wire 5 millimeters thick.
In order to calculate the weight of the reinforcing mesh, you can use the table given in our article.

Reinforcement mesh weight calculation table

Please note that different manufacturers may use custom mesh sizes. In this case, it is necessary to calculate its weight individually, using special formulas. A good solution would be to use mathematical spreadsheets for this calculation.

In addition, the mesh can be produced with various coatings. For example, a number of enterprises produce galvanized reinforcing mesh. This mesh has an incomparably longer service life and can be used for outdoor finishing work. For example, to create fences or railings.

Reinforcement mesh weight
Learn more about how to determine - the weight of the reinforcement mesh, and the calculator will help you calculate.

The concrete casting used to create the foundations is itself a fairly solid structure. However, its strength is great only in one direction - namely, concrete resists pressure well.

But the concrete foundations can be affected by loads in other directions. For example, it can be influenced by bending, twisting, and so on. The soil is a heterogeneous substance and, when frozen, can change its structure and volume, expanding in different directions. In order to give the concrete casting strength and resistance to impact in any direction, a metal power frame is introduced into the body of the concrete casting.

An excellent solution when forming a metal frame can be the use of a reinforcing mesh.

Reinforcing mesh. Characteristics and examples of use

In the process of its manufacture, wire sections or reinforcing bars are laid out with a certain step, and then at the intersections they are fixed by electric spot welding.

Reinforcement mesh - photo

Reinforcement mesh types

Reinforcement meshes can be classified according to several parameters. First of all, the reinforcement mesh can be divided into types based on the thickness of the source material used:

If the reinforcing mesh is made of a relatively thin metal wire, then it is conventionally called "thin"
In the event that the reinforcing mesh is made of a thick metal bar, then it can be conventionally called "thick".

In addition, the mesh can be produced with varying degrees of precision.

In addition, depending on the purpose, the reinforcing mesh can be produced with various mesh configurations. They can be rectangular or square.

Features of the use of reinforcing mesh

Reinforcement mesh can significantly reduce construction time using concrete castings.

The fixation of the intersection of the reinforcing rods can be done using knitting wire loops. It folds in half, wraps around the intersection and twists using a pointed hook or special automatic devices.

Calculating the weight of the reinforcement mesh

Calculating the weight of a reinforcing mesh can be useful for you to determine the total weight of a building structure, and for calculating logistics - that is, ways of delivering building materials to the construction site of the building.
To calculate the weight of the reinforcement mesh First of all, it is necessary to know the diameter of the used metal rod or wire, the pitch between the wire or rods and the configuration of the cells.
So, the step between the wire or rods can be from 5 to 25 centimeters. When creating a reinforcing mesh, both a wire with a diameter of 3 millimeters and a reinforcing metal bar with a diameter of up to 12 millimeters can be used.
Mesh labels use standard notation to help you calculate the weight of the reinforcement mesh.
So, if the reinforcement mesh is marked "150x150x5", then this means that this product has a square cell of 15 by 15 centimeters and is made of wire 5 millimeters thick.
In order to calculate the weight of the reinforcing mesh, you can use the table given in our article.

Please note that different manufacturers may use custom mesh sizes. In this case, it is necessary to calculate its weight individually, using special formulas. A good solution would be to use mathematical spreadsheets for this calculation.

With the help of this calculator, you can make online calculation of the weight and cost of a rectangular reinforcement mesh... In other words, by specifying the diameter of the reinforcement, the length and width of the mesh, the spacing of the reinforcing bars in both directions, the price of reinforcement for 1 ton, you can find out the indents (the distance between the edge of the mesh and the first bar) and the number of bars in both directions, as well as the mass , the length and cost of the mesh.

If you have several identical reinforcing meshes, then by specifying the number of meshes in a certain column, you additionally, you can calculate their total weight, length and cost... When one grid is counted, the number “1” is put in this column.

As for the additional percentage, then in this column you put such a figure, by what percentage you would like to purchase more fittings. This percentage is always taken into account when cutting reinforcement is meant. And usually it is 5%.

Note: the calculation takes into account the weight of 1 running meter. fittings according to GOST 5781-82 * and GOST R 52544-2006.

Reinforcement mesh weight and cost calculation

With the help of this calculator, you can calculate the weight and cost of a rectangular reinforcing mesh online.

How is the calculation of foundation reinforcement carried out?

Being engaged in the construction of buildings from monolithic reinforced concrete, you need to devote maximum efforts to assembling a high-quality reinforcing cage.

Without internal mesh reinforcement, the concrete structure remains brittle and does not flex. The reinforced concrete bearing element is distinguished by a much higher level of stability, the quality of transfer of loads, etc.

Reinforcement mesh for foundation reinforcement

In this article we will talk about how and why reinforcement cages are assembled, what reinforcement gives us, what role the reinforcement calculation plays in it, and also how to carry out this very reinforcement calculation.

1 Features and purpose

The calculation of the number of reinforcement for a foundation or any other supporting structure must be performed in strict sequence. It is unacceptable to refuse this operation.

At the same time, one must clearly understand why reinforcement is generally necessary, what advantages it gives, etc.

By itself, the reinforcement cage for floor screed, foundation (tape, slab, pile-grillage), columns, walls or floors, acts as a kind of skeleton.

The reinforcement tightens the concrete, increases its rigidity and the limit of its operational capabilities. If there is at least one rod per 10 square centimeters of concrete, its stability increases several times.

Moreover, both standard and secondary indicators are increasing. If you use the correct reinforcement scheme, then monolithic concrete can be used in the construction of any house, from small low-rise buildings to high-rise buildings, where the house scheme provides for gigantic structures several tens, if not hundreds of meters high.

At the same time, if you calculate all the costs, then you can understand one simple thing - even if a complex scheme consisting of many elements is involved to strengthen the supporting structures of the house, the cost of the structure will still remain acceptable in the end.

1.1 Design and layout

For the reinforcement of each structure, a specific scheme is used. Reinforcement scheme is the principle and rules by which the elements of the frame and mesh are assembled.

Reinforcing frame of the foundation

It is different for different designs. Accordingly, for different structures of the house, you need to think over different ways to calculate how much materials and weight are needed to create a particular frame.

Reinforcement mesh layout affects:

Calculation of the number of reinforcement.
Reinforcement weight calculation.
Parameters and principle of mesh assembly.
Methods for connecting the mesh into a single structure.
Load-bearing capacity and directionality of the mesh.
Diameter and weight of the reinforcement itself.

The grid scheme of any base consists of transverse and longitudinal reinforcement, laid in a certain sequence with a given step.

The rods of the transverse and longitudinal reinforcement are tied together using wire or couplings.

The wire should be used when it is necessary to overlap the nodes of the transverse and longitudinal reinforcement, and the couplings are intended for extending the rods.

Formwork with strip foundation wall reinforcement

Any frame consists of correctly laid longitudinal reinforcement, tied with additional transverse reinforcement. This binding allows you to create one of the edges of the wireframe. Further, it is permissible to use these edges as its main components.

If, for example, we are considering the frame of the floor of a house, then here we need to connect only two levels of the grid: the lower and the upper.

For wall structures of a house or strip foundation, two or three-level grids are used, attached to the transverse face in the form of a frame of strip base pillows.

For columns of a pile foundation or supporting structures of a house, rectangular elongated frames are formed, where the role of transverse reinforcement is reduced to ligation and stabilization of the overall structure.

1.2 Used fittings

The calculation of reinforcement for the foundation is carried out in order to be able to calculate our future costs, as well as to determine exactly what specific products we need.

As we noted above, different schemes provide for different types of wireframes. The frame of the strip foundation does not look like the frame of the pile foundation, and that, in turn, does not look like the frame of the floor.

Accordingly, the reinforcement itself in them should be used differently. Which one exactly depends on the characteristics of the house. However, we can highlight a few basic tips.

When selecting fittings, it is taken into account:

diameter;
Class;
place in the future constructive scheme;
load limit;
parameter of mass and length;
price.

The diameter affects how many loads the bar can carry without deformations. The larger the diameter, the stronger the structure. The larger the diameter, the higher the price of the rod and the indicators of its mass.

As a rule, reinforcement is used in the frames, the cross-sectional diameter of which starts from 8 mm and reaches 25-30 mm.

Reinforcing bars 18 mm thick

A diameter of 8-12 mm is suitable for lightly loaded areas of the frame. For example, for the device of transverse reinforcement when reinforcing the columns of the pile foundation, the device of the upper grid of ceilings, strip foundations, etc.

A rod diameter greater than 15 mm provides for it installation in working loaded sections of the frame, such as the bottom mesh of the floor, the base of the strip or the grillage of the pile foundations, etc.

Builders are trying to combine the working diameter of the rods so as not to bend the stick anywhere. Therefore, in fact, the calculation of the reinforcement for the foundation is carried out. It allows you to optimize the construction process and significantly reduce unnecessary costs.

The calculation itself is divided into 2 stages: the stage of calculating loads and quantities.

The first stage allows you to understand how many loads the structure takes on, how much it will withstand the weight, what the reinforcing cage should be, what rods should be used in it and how many should be.

The second stage is the calculation of a specific amount of reinforcement according to a previously obtained scheme.

The first stage is usually delegated to specialists. It is not recommended for beginners or people with no experience to perform load calculations. Exceptions apply only to small load-bearing structures.

For example, if you are interested in the reinforcement of a columnar foundation for an extension, a summer cottage, a portable kitchen, etc. Reinforcement of a columnar foundation carrying loads from such small structures is uncritical.

Another thing is the reinforcement cage for the foundation of a capital structure, or any of its other structures. This requires a trained eye, a clear understanding of goals, the nature of the actions of bearing loads, etc.

You can also use a load calculation calculator. Such a calculator is found on the Internet on most construction sites. However, the calculator only gives a general idea. The calculations that the calculator will provide you with accuracy and quality cannot be compared with the calculations from an experienced, time-tested specialist. And no calculator will give you a guarantee, if you entered incorrect parameters in its fields, then you will get the same result.

What you can use a calculator for is to calculate the amount and cost of reinforcement. That is, when working with the second stage.

2.2 Calculation of quantity

After calculating the loads, you already know from which reinforcement you need to create this or that frame element, with what step to assemble the meshes, etc. What you don't know is the exact amount of fittings. However, this knowledge is essential.

After all, you should come to the store and give a specific number to the seller, and not just show the seller documents with incomprehensible formulas.

Knowing all the future parameters of the frame, its bearing loads and the approximate level, it will not be difficult even for a beginner to determine the exact amount of material for reinforcing strip or pile foundations.

To do this, you will need a regular calculator and a few sheets of paper.

2.3 An example of calculation depending on the type of construction

To begin with, we will consider the principle of determining the amount of reinforcement of the pile foundation.

The structure of the pile foundation consists of columns and a grillage. Column reinforcement is fairly easy to count. It is enough to find out the number of longitudinal thick rods per column.

Next, we calculate the transverse reinforcement. The transverse reinforcement fixes the longitudinal one. Here it is enough to find out the distance between the thick longitudinal reinforcement and its length. The ligation with the transverse rods of the columns is carried out with a step of 20-30 cm, respectively, it will not be difficult to determine the specific values.

The calculation of the design of the strip foundation is somewhat more complicated. A strip base is characterized by the presence of several planes. However, we will consider its basic design, in the form of a tape without a sole.

In this case, the tape is knitted from two parallel frames, tightened with transverse reinforcement. The number of bars per frame depends on its size and the selected step.

If, for example, the wall of the strip base is 10 meters long, and the reinforcement pitch is 30 cm, then dividing 10 by 0.3 we get about 34-35 rods. That much material will be needed to form one of the mesh parts.

Bottom reinforcement mesh in the slab formwork

As you can see, for such calculations, it is enough to use the simplest calculator.

The calculation of overlaps is carried out in the same way, only there are already 2 grid levels in it. The lower level is made of thicker reinforcement with a large step, and the upper level is made of thinner ones, with a smaller step and does not cover the entire overlapping area.

The principle of quantification is similar here. We divide the length of the slab by the step of the reinforcement, then we perform similar actions with the width. As a result, we add two numbers and we get the total amount of reinforcement for the lower mesh. Then, according to the same scheme, we count the upper one, and the job is done.

Tables of dimensions, weights and characteristics of the reinforcement mesh. Self-calculation formula

Reinforcement mesh is a building element made of special corrugated wire, which is fixed by welding at the intersection points to form characteristic square cells. Whoever has seen it at least once will not mix it up. The mesh is intended for reinforcing concrete elements and serves to ensure the strength of the entire structure.

Standard mesh sizes

A welded mesh is made of metal rods, the total diameter of which is from 3 to 40 mm... It is divided into light and heavy types, while the former have a rod diameter up to 10mm., and the second from 12mm respectively.

Considering the size of their cells, with the naked eye, you can see the difference, which is from 0.5 cm and comes to 2.5 cm.

Reinforcing mesh can be made of a large area and reaches a length of 12 meters, with a minimum value of one meter. The maximum width is 240 cm, at the minimum value at 50 cm.

Table of geometric characteristics of welded meshes TU 14-4-1284-84

Reinforcement mesh classification

Types of reinforcement products:

d, e- spatial frames of T-section and I-section, respectively

s- space frame bent from meshes

Reinforcement mesh is divided into two main subspecies presented below:

1. According to the original the location of the working fittings.

The working reinforcement goes in one direction, and is distributed in the other (both longitudinal and transverse strips can be working).

Working fittings are made in both directions.

2. By diameter vertical and horizontal rods.

Heavy types include nets with a diameter over 12 mm... The lungs include all other meshes that are in diameter from 3 to 10 mm inclusive.

In order to increase the service life, this building element can be galvanized or treated with polymers, which have a protective function and prevent the formation of corrosion.

At the moment, a unified standard marking has been adopted to designate types of valves:

AI(hot rolled smooth, Roman numeral I denotes strength level)

AII, AIII, AIV. AV, AVII(hot rolled ribbed)

AT III, AT IV, AT V, AT VI(hot rolled thermally hardened)

IN 1(cold rolled with round section)

BP-1(cold rolled with periodic roll forming)

Decryption example

How to calculate the weight of the material

The easiest way to determine the weight of the reinforcement mesh is to use the table in which everything is already “calculated for you”.

Sectional area, cm²

Plain and high-strength wire

A-III, ordinary and high-strength wire

A-II, A-III, A-IV, At-IV, A-V, At-V, At-VI

Conversion tables m 2 to kg

Welded mesh TU 14-4-1284-88

Welded reinforcing mesh TU 14-4-184-93

Welded mesh from wire ВР-1 and reinforcement В500С in cards (sheets) we will cut 2000х6000 mm

If tables are not at hand, then the weight can be found out by simple calculations.

The area in brackets is the area of the circle. D- diameter.

In order to obtain the weight, it is necessary to multiply the volume by the specific gravity.

Calculation example

We calculate the volume: 1 m x (0.785 x 0.012 m x 0.012 m) = 0.00011304 m³

We calculate the weight: 0.00011304 m3 x 7850 kg / m³ = 0.887 kg

The result obtained above will be identical with the tabular data that can be used within the framework of “correcting errors”.

Also, one cannot fail to mention the specialized online calculator “ LotServisCalc“. A convenient service allows you to get data in just a few clicks. He will calculate the weight as quickly as possible, not only for the reinforcement mesh, which is marked there as welding, but also for any other.

Scope of application of the reinforcing frame

Reinforcing mesh provides a multiple increase in the strength of any structure that requires its use. Reinforcement of the foundation and making the walls more durable - creating a kind of wall frame are considered the key tasks in construction. which ensures the long-term operation of the entire structure.

Reinforcement of rapidly destructible road surfaces.

For reinforcement during masonry work.

To strengthen the foundation.

To improve performance and strengthen thermal insulation.

For leveling and maximum strengthening of the original floor covering.

For strengthening walls when working with plaster.

It is also used in the production of partitions both in private houses and in apartments.

Non-standard material use:

Need for invention is cunning. Surely you yourself have repeatedly noted the reinforcing wire used not at all for reinforcement. As a rule, this happens when a roll remains after construction and you need to put it into action. Here are some examples:

Some craftsmen use rebar when building pet cages.

And they also use a reinforcing mesh for the manufacture of various small parts in the form of mousetraps or feeders (a special feeder for fish).

When nothing better is found at hand, it is used as a barrier for ventilation pipes and openings.

The cement mortar can be made more greasy, that is, more plastic and convenient to work with. To do this, add a detergent to it - always based on soap, like "Fairy", and not a synthetic detergent.

Reinforcement mesh weight

Information portal about suburban construction. Only up-to-date information about real estate, installation schemes, description of materials, comparative analysis of technologies, do-it-yourself crafts. Useful for every owner of his own house or cottage.

The universal metal steel weight calculator allows you to quickly and accurately calculate the weight of specific steel grades. In the metal calculator, you can calculate the weight of steel, cast iron, aluminum, brass, bronze, copper, magnesium, titanium, nickel, zinc, as well as a wide variety of alloys based on these and other metals.

External engineering networks are one of the most difficult stages of construction that requires special attention, something that no residential building can do without.

Calculator with which you can calculate the volume of earthworks.

There are automatic tools to determine the theoretical mesh weight, such as the mesh weight calculator. It will help you quickly calculate the weight of masonry, welded mesh, chain-link mesh and wire.

With this calculator you can calculate the weight and cost of a rectangular mesh. In other words, by specifying the diameter of the reinforcement, the length and width of the mesh, the step of the reinforcing bars in both directions, you can find out the indents and the number of bars in both directions, as well as the mass and length of the mesh.

The UnitConverter converter program allows you to convert the same type of values into formats of different countries and standards.
The calculator contains 28 categories of quantities and 1194 measurement units.

The range of rolled metal - catalogs of sheets and profiles supplied by factories (angles, I-beams, channels, pipes), which indicate the dimensions, weights and geometric characteristics.

The program is intended for performing thermal engineering calculations of multilayer enclosing structures and checking the thermal engineering characteristics of multilayer structures.

Calculated cross-sectional areas and reinforcement mass. Range of hot-rolled rebars, regular and high-strength reinforcing wire. Directory.

The concrete calculator will help the builder, without complicated arithmetic operations, to deduce the exact amount of concrete mixture required for certain works.

Pipe calculator for calculating pipe weight. Calculation options for round square and rectangular pipes made of various metals. Materials: carbon steel, duralumin, titanium, copper, brass, lead, gold and others.

WinDjView is a fast and easy-to-use DjVu viewer for Windows with document tabs, continuous scrolling and advanced printing. The DjVu format allows you to save documents and pictures with high quality in small files. The utility is a cross-platform program and runs under Microsoft Windows and Mac OS X operating systems.

The incredible thing until recently is an alternative PDF viewer that works without any Adobe products on the system. Small, fast, capable. In recent years, the program has become quite user-friendly and pleasant to look at. Despite rare font display issues, Foxit Reader is one of the best alternatives to Adobe.

WinRAR is a special computer program that compresses data into one file. As a result of its work, an archive is obtained for easier transfer or for compact storage of files and folders. WinRAR is used every day by millions of people around the world to save PC space and transfer files quickly. It is difficult to imagine everyday work with archives without it. WinRAR supports work with many archive formats at the maximum speed and high data compression ratio.

The calculation program is intended for the design of engineering systems for various purposes using technical insulation "K-FLEX", covering protective materials and components in the structure, based on the requirements contained in the technological design standards and other regulatory documents.

Also on the topic

Vladimir Vysotsky: a short biography and work of the poet Vysotsky short biography and work

The story of a summer hike in the forest

Calculation of the turnover of working capital, definition, formulas

Short biography for children

Presentation "junna moritz" presentation on fiction on the topic