It is quite easy to clean a clogged toilet, unless of course it is the toilet that is clogged, and not the sewer pipes behind it. It's pretty easy to check. If the water does not leave only the toilet, then it is he who is clogged, then we read further this article. If the water does not even leave the bathroom, from the sink, then the problem is a pipe, there is a blockage of the sewer pipes after the toilet, and possibly the sewer riser - serious intervention is required here.
As a rule, the toilet is clogged with paper, berries in compote, chicken bones, small rags, bags, etc.
Citizens! The toilet is not a bottomless hole! You should not send anything there except sacks and paper!
So, to clean the clogged toilet, we need an ordinary plastic one and a half or two-liter bottle of lemonade or beer. Covered. This bottle needs to cut off the bottom.
Next, you need to fill the toilet with water. You can just flush the tank, but it is better to fill a bucket of hot (preferably very hot) water and fill the toilet with it. From hot water everything happens faster and better. Then we take our bottle with a cut off bottom, insert it into the hole of the toilet bowl and begin to make up and down movements with force, as if pushing water further into the toilet bowl. Thus, with a few movements, we can eliminate a small blockage in our toilet bowl. If this method does not help, then you have a serious blockage, you need
If you didn’t have anything at hand, neither a cable nor a plunger, an ordinary plastic bottle with a volume of 1.5-2 liters can come to the rescue. When choosing a bottle, make sure that its lower part freely passes into the drain hole and reaches the bottom.
We need a sharp knife as a tool. On the neck you need to tightly screw the cap of the plastic bottle. Take a marker or felt-tip pen and draw a cut line on the bottom and cut it off.
Try to cut the toilet cleaner bottle straight, without sharp waves or bends. Insert the bottle into the neck of the toilet and make forward movements with the cut part, pushing the water creating pressure.
After the problem is solved, flush the toilet with hot water.
No need to pour boiling water, which can damage the faience coating of the toilet bowl, leading to microcracks due to a sharp temperature drop and even noticeable wall cracks. This also applies if the toilet is connected to the sewer through a plastic corrugation.
Working with a bottle resembles cleaning with an ordinary plunger. The effect of water hammer is created, destroying the blockage and pushing it into the sewer system.
While punching the toilet with a bottle, be prepared for a reverse water hammer that can spray a fountain on you and get your clothes. It is better to change clothes in advance and put on rubber gloves and goggles.
It is better to clean the bottle before pouring hot water into it, this is especially important when the toilet bowl was previously drained of greasy slops from pots and pans, thus achieving softening of fat deposits by first adding dish detergent there.
A plastic bottle will help to cope with small blockages at home: toilet paper, cotton wool, a rag, pushing them down the drain.
Video: Clogged toilet how to clean
How to clean the toilet from blockage at home without a cable
Rope from a plastic bottle
If you need to get some fallen object into the toilet, a homemade cable from a plastic bottle will help.
To make a homemade cable, take a five-liter (5lit) plastic bottle, but if it is not there, you can use a 2-liter one, only the cable will be shorter. Take large scissors as a tool.
Take a marker (pencil does not draw on plastic) and apply a spiral marking 2-3 centimeters wide along the entire length of the bottle.
The lower part of the bottle (the material is always thicker and stronger) will be used as a round handle - a ring. Cut the bottle along the entire length, you will get a plastic band with a ring at the end. Make a hole in the end of the cable so that the finger can freely enter. At an angle of 45 degrees, make notches along the spiral of the cable.
Make the notches not deep so that the cable is strong.
You push a home-made cable, for the toilet, scrolling it along its axis into the neck, holding it by the handle. By rotating the cable, you can pick up debris and foreign objects and pull them out.
As you pull the cable and clear the blockage in the toilet, you will notice how water begins to pass, indicating that the blockage has been cleared. As soon as this happens, remove the plastic cable and flush the toilet with hot water.
How to pierce a toilet with a doll
sand bag Using a doll (as people call a bag tied with sand on a rope) to punch the toilet, if the toilet is clogged, clean it yourself without a plunger and a cable, eliminating small blockages from toilet paper, hair, etc.
Place the doll in the neck of the toilet and hold it by the rope and press the flush button. Then carefully remove the sandbag, which, under the action of water hammer and its own weight, pushes the blockage into the sewer pipe, clearing the drain.
Rag for cleaning the toilet without a plunger
To do this, we need a large rag, a stick more than a meter long (a mop will do) and a few more small rags. With small rags, you need to plug all the drain holes in the apartment: a bath (you can use a cork), a sink, a sink in the kitchen, etc. Do not miss a single one.
A large rag should be wetted and squeezed out. Wrap it on a stick in such a way that it does not go into the pipe under any circumstances. It must either be fixed with something, or held by the hand by the edge. The main thing - do not miss it in the bowels of a white friend! In general, it should turn out something like in the picture:
simple rag for cleaning the toilet Now we lower our “torch” as shown in the figure at number 2, let the water down and sharply push the “torch” ... there! But abruptly - it's not with all the dope that the toilet bowl breaks. It is necessary to make a short, accurate and at the same time quick downward movement.
Pushed there. Stopped for a second. And just as sharply pulled out. Then again sharply push the "torch" into the toilet. Until the water comes down. After that, it is necessary to drain the water again and do everything again until the result is achieved. Keep in mind such a moment, if you have a drain left open somewhere or there are loose connections in the fan pipe, then this method of cleaning will not work. And at the same time, it is not necessary to push the “torch” into a push on a grand scale and with a run, because the poop will be on the walls.
Toilet clog pump sticker
Chinese and Korean industries have started to produce special films. It will help you quickly and effortlessly deal with small blockages in a matter of minutes. This film is very convenient for those who often rent an apartment and are ahead from place to place, there is no need to carry a plunger and a cable with them.
Throw more toilet paper on the clog to increase the rise of the water. Stick the film around the perimeter of the toilet on a dry surface, carefully smoothing it around the edges, releasing air. There should be no air bubbles or gaps. Drain the water and press down on the air bubble several times, pushing the air in.
Video: Clogged toilet pump sticker
A blockage of drains in an apartment is an unpleasant problem, but when the toilet bowl becomes clogged, it is doubly inconvenient, since the task requires an immediate solution. Often the cause of difficult draining of water in the toilet is the deposition of salts in the pipes. This happens due to hard water, urea or other kinds of sediments deposited on the walls of the pipes and narrowing their inner diameter.
Salt deposits in the pipe. The “aesthetics of the frame” is accompanied by an appropriate smell
Advice! To find out the localization of the blockage, open the taps in the bathroom and in the kitchen (sources of water to the common drain). If here the water goes into the drain freely, then the reason is in the toilet. If its drain is slow everywhere, then the problem is in the common pipe. In this case, call the plumbers - it will be difficult to cope with the trouble on your own.
Attention! If you find a blockage in the toilet, do not drain the water from the tank, since its minimum volume is 3 liters. For reliability, you can turn off the water supply tap so that it does not flow to the floor when the drain is clogged. Use a bucket, pouring no more than 1 liter of liquid into the toilet to check.
Cleaning risers, especially in old houses, is a job for professionals
Important. Prevention of salt formations allows you not to spend further effort on cleaning pipes. It is enough to fill all the drains in the apartment with a special cleaning liquid once every 3 months at night.
However, the main cause of blockages in the toilets is the residents themselves, who use the plumbing fixture as a garbage chute. And if a meat bone that accidentally fell into the toilet is easy to remove, then a rag or paper blockage will require some effort.
Blockage removal tips:
- When replacing sewer pipes, install new ones of the same diameter, no less.
- When making repairs in the toilet room, close the toilet so that construction debris does not get into it.
- Do not be lazy to throw away garbage (pads, newspapers, cat litter, etc.) in the places provided for it. So you will save your time, and you will not blush in front of the plumber.
How to clear a blockage in the toilet yourself
There are several ways to clear toilet blockages. Their effectiveness depends on the complexity of the cork: material, volume, time of occurrence.
Advice! Before attempting to clear the blockage, drain the water from the toilet to the level of the drain. A rag, sponge or rubber pear (enema) is suitable for this.
Mechanical ways to clear a clogged toilet
Important. The diameter of the plunger tip must be larger than the diameter of the toilet bowl drain. This is the only way to create conditions for the occurrence of water hammer.
This simple plumbing tool will help clear a small blockage in the toilet
If the apartment does not have a plunger, then you can use plastic bottle, the bottom of which is cut off, and the lid is tightly twisted:
- the resulting device is gradually introduced into the toilet hole until the air in the bottle begins to push it back;
- with a sharp movement, the bottle is pressed all the way into the drain and immediately removed.
The pressure created is powerful enough to break through the garbage plug with two or three manipulations.
Plastic bottle + laws of hydraulics = homemade plunger
If the above methods did not help fix the problem, then you can use household chemicals.
Decontamination chemicals
Attention! If the connecting corrugation between the toilet bowl and the pipe is made of thin plastic, then under the influence of boiling water it may burst. In this case, you need to use warm water.
Attention! Before you decide to act drastically by pouring a solution of formic, hydrochloric or sulfuric acid into the toilet, think about whether the product will corrode the old pipes at the same time.
Professional plumbing cable
This is a special plumbing tool, which is a cable with a handle at one end and a nozzle at the other. There are many types of cables (rope, spring, rigging, tension, etc.) with a diameter of 6 to 16 mm and a length of up to 60 meters.
For apartment needs, a five-meter cable Ø9 mm is enough. The nozzle at its end can be in the form of a weight (for punching) or a spiral (for removing blockage)
1.
2.
3.
4.
Many property owners have to think about how to clean the toilet themselves. Even when expensive high-quality plumbing is installed, problems with cleaning sewer pipes can hardly be avoided.
The main thing is not to panic, because there are many proven ways to clean the toilet at home.
How to clean a clogged toilet
The easiest option, how to quickly clean the toilet and pipes, is to use ready-made products specially designed for this purpose. They are liquids, gels, granules or powders, which are chemicals that have a composition that can dissolve pollution.
In the case when, after using chemicals, the water still does not leave well, a foreign object, and not an organic blockage, may be the cause of the trouble. It is possible that a cloth or a rag for washing surfaces has got into the plumbing fixture. In this case, it is necessary to clean the clogged toilet using physical methods.
It should not be forgotten that chemicals are able to dissolve mild organic blockages, but when foreign objects get into the drain, they are powerless and are not able to eliminate the blockage. But if you don't know how to remove plaque in the toilet, chemicals will help you in this matter.
Cleaning with a plunger
You can eliminate the blockage in the toilet with a plunger - this work has its own characteristics. This plumbing product cleans the sewers due to the vacuum. To do this, the device is installed on the drain hole so that the water covers the rubber part of the tool. If there is more of it in the toilet than required and you cannot do without a plunger, you will have to scoop out the excess liquid with a bucket.
With this position of the sanitary ware, it is necessary to make at least 10 intensive movements up and down, leaving the rubber seal on the drain. Then the plunger is removed with a sharp jerk and the procedure is repeated until the water level begins to subside. What it looks like removing a blockage with a plunger can be seen in the photo.
After the successful elimination of the blockage, cleaning the toilet bowl continues with the use of a chemical agent and washing it with boiling water. Sometimes, instead of a plunger, they use a stick, on one end of which a rag is wound (read also: "").
Cleaning the toilet with a plastic bottle
So, when the toilet is clogged - how to clean at home, if there is no plunger. When there is no plunger at home, you can use the most common plastic bottle with a capacity of 1.5-2 liters. Its bottom should be cut off, and screw the lid on the neck. Then the bottle is inserted with the bottom part into the hole and is continuously moved up and down with force several times. After the interference is eliminated, the cleaning process is completed by rinsing with hot water, and usually the plumbing is fully restored.
Cleaning the toilet with a plumbing cable
If all of the above options for cleaning the toilet do not help, you can use a plumbing cable, which is considered a professional tool (in more detail: ""). It is a metal rope with a sharp tip or a spiral-shaped drill at one end and a handle at the other. The photo shows a plumbing cable designed to clean the sewer.The tool is slowly inserted into the drain hole with rotational movements according to the clockwise movement. When an obstacle arises in his path, you should not stop, because he most likely rests on the toilet bowl.
The moment, if the drill gets stuck in a blockage, can be determined by the fact that the movements are difficult both when moving clockwise and against it. In this case, they act with short movements in the direction up and down and left and right, thereby trying to push the obstacle into the sewer pipe. Working with the cable requires care so as not to damage the sewer system.
If the water level in the bowl of the device begins to drop, the cable is removed by rotating it in the opposite direction. When deciding how to clean the toilet, you must remember that plumbers professionally work with this tool. A solvent is poured into the drain hole after completion of work. When the water begins to go down the drain at the same rate, the toilet is washed with a large volume of hot water.
The process of removing a blockage with a plumbing cable requires certain practical skills, at the same time, inept movements can lead to new problems. If the sewer system is in poor condition due to prolonged use, then they use other methods and decide how to clean the toilet, or call specialists.
How to clean the toilet with a bottle: a detailed description of the process
Every home should have a sewer cleaner. Blockages in the toilets do not appear on schedule, but at those moments when no one expects problems and there is no time for shopping.
In such cases, you can get by with improvised means, and an ordinary plastic bottle will help save the situation. Let's look at how to unclog a toilet with a bottle and what else you can use to quickly fix plumbing problems.
Causes of blockages in the toilet
A clogged toilet is one of the biggest problems that can happen to a sewer. If the water drain stops, then sewage fills the bowl of the plumbing fixture, and a heavy smell spreads around the house.
If a blockage occurs, it should be eliminated as soon as possible, otherwise an unpleasant smell will appear not only in the apartment, but even in the entrance
Although the very first and most important thing is cleaning, it is still advisable to figure out what exactly provoked the stagnation of water in order to know how to properly handle the plumbing fixture in the future.
There are two main reasons why a blockage may appear: improper installation and negligent attitude towards the operation of the toilet. The operation of the toilet can be disrupted if it is connected to the riser by a pipe that is too large. The slope is not enough for the normal discharge of wastewater, and deposits remain on the walls of the pipes.
The clearance in the pipes gradually narrows, so sooner or later there comes a moment when it becomes insufficient for the passage of water. The cardinal way to solve problems associated with poor-quality installation of the device is proper installation.
With regard to operation, it is important to remember: the toilet is a useful plumbing equipment, not a garbage dump in which you can dump garbage. The device is not intended for pouring out cat litter, throwing away cotton wool, rags, diapers, thread, food waste, construction debris and cement mortar residues.
If the toilet is treated like a trash can, it will inevitably end up with blockages. Nothing extra can be thrown into it. Accidentally dropped objects should be immediately removed from the toilet, and not ignored, and even more so not flushed, pushing further into the sewer pipe.
General principles of sewerage
The sewer system consists of a riser and pipelines that are designed to drain liquid effluents from plumbing fixtures. The riser is a large diameter pipe and is usually located in the bathroom.
If water stops draining in the toilet bowl of an apartment in a multi-storey building due to a blockage in the riser, this is a problem for all residents. Only utilities can solve it. Special revision niches are provided for cleaning the risers
Modern risers are often made of plastic, but many homes still have cast iron pipes installed. The advantage of cast iron is strength, and plastic risers are less prone to clogging. Most often, old cast-iron pipes are clogged. There are burrs on their inner walls, which is why deposits form quickly.
To prevent air from the sewer from entering the room, a siphon is provided in the design of the toilet - a bend where a water plug (water seal) is constantly located. When draining, water displaces and replaces this plug, pushing sewage from the toilet bowl into the sewer riser.
When you press the tank button, the water drains into the bowl, washing it, and passes further along the pipe into the riser. The blockage interferes with the normal operation of the toilet, and the water remains in the bowl
If there is debris in the pipe and the water has not squeezed it into the riser, a blockage may form. Scraps of paper, waste, hair, threads are caught on sharp or large objects. Gradually, all this turns into a large lump of dirt, which narrows or completely blocks the pipe section.
Cleaning blockage with a plastic bottle
If there are no sewer cleaners in the house, the situation can be saved with a regular 1.5-2 liter plastic bottle. All you need is a sharp knife.
The sequence of manufacturing a device for cleaning the toilet:
- Screw the cap tightly on the neck of the bottle.
- With a felt-tip pen or marker, draw a line at the bottom of the bottle above the bottom.
- With a sharp knife or large scissors, carefully cut off the bottom. Make sure that the cut line is even, without any special protrusions and depressions.
To clean the toilet, insert the bottle into the drain hole with the cut part and sharply, forcefully push the water up and down several times. Then flush the toilet with hot water. Watch the temperature of the water: it should be hot, but not scalding. Otherwise, the plumbing may simply burst.
According to the principle of operation, a home-made cleaning device from a bottle resembles a plunger. Water practically does not compress, its volume remains unchanged. By pushing water with a bottle deep into the toilet, you can create a water hammer effect and thereby destroy the blockage.
Choose a bottle of such a diameter that its lower part freely passes into the toilet drain. It is desirable that she reaches the bottom
When cleaning the toilet bowl with any tools, incl. and homemade, there is always a risk of damaging plumbing or getting unpleasant “side effects”:
- Too strong reciprocating movements can ensure that the water does not rush into the pipe, as expected, but out. In this case, the fountain from the toilet can hit the ceiling.
- With careless movement, you can hit the toilet or drop a hard, heavy object on top of it. This threatens the appearance of cracks and chips on the device, especially if it is made of fragile faience.
Such phenomena are infrequent, but they do happen, so care should be taken. The risk of "water hammer in the opposite direction" exists if the toilet is clogged with solid objects: glass fragments, construction debris, cement.
Thanks to the bottle, a pressure difference can be created, and the plug that closes the drain will move further along the pipe. Hot water will dissolve fatty deposits and push dirt to the riser
If pieces of paper, cotton wool, rags or other soft objects get into the toilet, then a plastic bottle is quite capable of pushing them into the sewer without any problems. You can also use it to get them out of the toilet. To do this, you need to build a homemade plastic cable.
Rope from a plastic bottle
To make a plumbing cable, you will need a large 5-liter plastic bottle. If there is only a 2-liter, it will also fit, but the product will turn out to be shorter. Of the tools you will need large durable scissors.
Work order:
- To begin with, markup should be applied. An ordinary pencil does not draw on plastic, so it is better to take a marker or a children's felt-tip pen. It is necessary to apply a spiral strip 2 cm wide along the entire length of the bottle.
- In the manufacture of bottles, manufacturers use thicker plastic at the bottom of the products. The material bends worse, but is much stronger than in the upper part. It is perfect for a pen that will look like a ring. Draw this detail right away.
- Cut the bottle according to the markup. You should end up with a long spiral ribbon with a round element at the end.
- Cut a hole in the middle of the "ring" so that your finger can freely pass through it.
- Make notches along the entire length of the tape: cut it on both sides at an angle of 45 degrees. Make sure that the serifs are not too deep and the cable retains its strength.
To remove or move objects stuck in the toilet, insert a homemade cable into the drain hole, holding the handle. Try to push the product as far as possible and gently scroll around its axis. When the cable reaches the blockage, the rotational movement will help to hook the debris onto the notches.
To clean the toilet, it is better to choose a larger bottle and make a tape 2.5-3 cm wide, because. These appliances tend to get more clogged than sinks.
Try to remove stuck items. If that doesn't work, just push them down the pipe. A sign that everything turned out right will be a decrease in the amount of drains in the toilet. As soon as sewage begins to go down the drain, rinse the device with hot water.
Cleaning the toilet with a floor cloth
In the absence of a plunger, even the most ordinary doormat can become a powerful weapon in the fight against toilet blockages. In addition to it, you will need a wooden block as thick as a mop handle. You can use the mop itself, but this is not always convenient due to the large length.
The rag can be wrapped around the end of the squeegee and secured with string so that it doesn't fall off while the handle is moving.
A wet rag should be folded and plugged with a toilet drain hole. You will get a dense impromptu cork. In its center, you need to attach a mop or bar and press hard several times, like on the handle of a plunger. A sudden movement causes water hammer and destroys the plug.
Unique Chinese method
The Chinese and Korean industry produces a special film for cleaning the toilet. If you manage to find it on sale, be sure to buy and store it. In case of blockages, the film can be a real salvation, because. eliminates them in a few moments.
Chinese film disposable. It is very convenient to store it. This is ideal for rented accommodation if tenants don't want to buy a cable or plunger and then transport it to a new place of residence.
The principle of cleaning the toilet with a film is simple to genius, but it looks rather strange, since you first have to increase (not reduce) the blockage. This is done as follows: they throw crumpled toilet paper into the stagnant water of the bowl and drain the tank so that the toilet is filled almost to the brim.
The toilet rim is wiped dry and a special high-strength film is glued. It should fit snugly against the rim over the entire adhesive surface so that there are not the slightest gaps or air bubbles anywhere.
The places where the film adheres to the toilet are carefully smoothed out. After that, the water is drained from the tank several times so that the film inflates, and the bubble is pushed down with smooth wave-like movements.
Two or three pressures on the swollen film are enough for a mass of water and paper to break through the blockage and instantly merge into the sewer. After use, the film is carefully torn off the rim and discarded.
Some especially bold "craftsmen" advise using food film instead of a special film. They offer to close the toilet hermetically with it, draw water and press from above in the same way.
This method raises great doubts, because the tightness of the food film is in question. In addition, it is not strong enough, so it can not withstand pressure and burst. In this case, the entire bathroom will be flooded with the contents of the toilet bowl, and the blockage will still not go anywhere. It's better not to risk it.
Other ways to clear blockages
The modern market for plumbing fixtures is diverse: you can find any tools for mechanical cleaning of sewers. Some of them are very compact and easy to use. Classics of the genre - cable and plunger.
A metal cable cannot always be used, because. there is a risk of damaging the plastic elements of the sewer system. But a rubber or silicone plunger is an indispensable thing in the household.
An alternative to mechanical methods is household chemicals. Packing a good specialized drain cleaner will cost less than any plumbing fixture and take up very little space.
When buying household chemicals for sewer cleaning, carefully read the information on the package, which indicates which pipes can be used for
Household chemicals not only corrode traffic jams. It removes from the inner surfaces of the pipes that plaque, due to which the lumen narrows and blockages form. An additional plus is disinfection, which is never superfluous in the toilet.
Useful video on the topic
You can choose any of the ways you like to clear a blockage in the toilet. We offer videos that will help you understand the operation of the plumbing fixture and fix problems.
Video, thanks to which you can understand how the flush system in the toilet works:
Detailed instructions for using a plastic bottle to clean the toilet:
The Chinese method of dealing with blockages in the toilet with a special adhesive film:
There are many ways to clear blockages in the toilet, incl. very original. However, it is better not to reinvent the wheel, but to buy an ordinary plunger. If you wash it, dry it after use and store it in a secluded corner of the bathroom, it will last for many years. If you didn’t take care of buying a plunger in time, and the toilet needs to be cleaned urgently, a bottle will help you.
sovet-ingenera.com
How to clean the toilet from blockage yourself at home
The toilet, paradoxically, is the most indispensable place in any apartment, so a clogged toilet bowl can disturb the peace of the household. The article contains 9 of the most common methods in the fight against blockages: from budget to expensive, from easy to cardinal.
improvised means
First of all, you can try folk ways to remove blockages, which will not only help solve the problem, but also save the family budget.
Testing boiling water
A simple and free method of dealing with blockages, when an enamel or iron bucket of water is boiled and abruptly poured into the toilet.
However, the method is fraught with dangers:
- Boiling water can scald household members. To puncture the cork, it is necessary to turn the bucket over sharply and vertically, which will lead to the formation of a lot of splashes.
- Hot water can ruin the toilet itself. A temperature drop, at best, will lead to the appearance of small cracks on the surface, and at worst, the faience product may burst.
In addition, according to reviews that still ventured to test the method, boiling water only helps against light blockages with food waste or wood cat litter.
Vinegar Soda
Another budget toilet cleaning method is a mixture of baking soda and vinegar:
- Half a pack of soda is poured into the flush hole.
- 2 cups of ordinary vinegar is also poured there.
- From above, the hole is laid with a large dense rag, for example, an old terry towel.
As a result of a chemical reaction between baking soda and vinegar, slight blockages in toilets and bathrooms break through. A side effect of the method is the ability to ruin sewer pipes if you overdo it with soda. It is recommended not to try to increase the dosage.
Citric acid and washing powder
Fans of soft multi-layered toilet paper often encounter blockages precisely because of it.
An effective way to get rid of adversity, which at the same time will clean your faience friend from yellow streaks or rust:
- 1 cup of any washing powder dissolves in warm water.
- 2 sachets of citric acid are poured into the solution.
- The mixture is poured into the toilet for 4-5 hours or for the whole night.
- In the morning, several buckets of warm water are poured into the toilet to wash away the softened remnants of the blockage and the cleaning solution.
One of the most popular and effective remedies for stone plaque, old rust and other toilet contaminants, which, among other things, will cope with a slight blockage.
The recipe for use is simple:
- First, the toilet bowl is freed from water. For example, a hand is wrapped in a rag, and then water is pushed out with piston-like movements.
- A bottle of "Whiteness" is poured into the drain hole. It is advisable to leave the remedy for the whole night.
In the morning, the dirt from the faience will definitely go away, and light blockages from paper or pet hair may also disappear.
We use chemistry
In case of inefficiency of improvised folk methods, the next step is to use the means of industrial production.
On the shelves of stores there is a large assortment of household chemicals for cleaning toilets and pipes, although they all consist of alkali or acid:
- Domestic brands. Inexpensive "Mole". "Clogging".
- foreign brands. High price range products such as Tired, Domestos.
According to the instructions on the package, the desired dosage of the product is poured into the toilet. After a few hours, it remains only to wash off the remnants of the blockage. From the first time, household chemicals may not cope with the problem.
If the water began to leave at least a little, you should pour the product again. If there is no effect at all, then you need to try more serious methods.
The main thing is to follow the safety rules:
- Do not mix chemicals from different types or manufacturers. You will be lucky if the mixture that has changed its properties does not work, it will be worse if it ruins the plumbing or even the health of the household.
- Do not try to create a chemical mixture yourself or buy it from hand, use only industrial samples. The result of chemical reactions can lead to anything, to say nothing of an unknown composition offered for a penny at street stalls.
- When using aggressive products, use safety goggles and rubber gloves.
Important: after cleaning the toilet bowl with “chemistry”, you should rinse it several times with water before the first use.
Mechanical methods
Not a single chemical agent will take sand, construction waste or glass, therefore, in such cases, experts advise immediately using “heavy artillery”: a plunger, a plastic bottle or a cable.
plunger
A dark rubber suction cup with a handle is familiar to many from Soviet life. With this tool, you can try to push the blockage further into the sewer. In the general system, the diameter of the pipe is larger, so the debris floats freely further.
Plastic bottle
In some cases, a regular 1.5 liter plastic bottle with a stopper can deal with a blockage much more effectively than caustic chemicals or folk methods.
Let's describe the algorithm of actions in detail:
- The bottom of the bottle is cut off, while the cork is not twisted.
- We put on long rubber gloves and lower the hand with the bottle into the toilet hole, deep into the cut edge.
- Then several times with strong sharp movements we drive the bottle farther and farther.
The method with a bottle is similar in effect to actions with a plunger, but the force of the water hammer is many times greater. Due to the increased pressure, the blockage can fly further into the riser and float away into the wide sewer.
Cable
The cable is considered a professional plumbing tool. It is profitable to buy such a tool than to pay several times more for calling a specialist with it.
A standard steel cable reaches a length of 7-10 meters, has a handle and a pointed tip.
In order to destroy stagnant garbage with it, you must:
- Holding the handle, dip the tip of the tool to the maximum into the toilet drain.
- Next, with rotational movements, it is necessary to advance the cable to the blockage and try to push it through with gentle pushes.
Important: all movements must be carried out slowly and slowly, as sharp and strong blows of the cable can damage old sewer pipes.
drastic measures
In the event that it was not possible to remove the blockage using the available methods, it remains only to disassemble the toilet bowl.
- In Soviet times, the toilet was fixed with cement, so a specialized tool is needed for dismantling.
- The pipe leading to the toilet can also be embedded in the wall.
- With self-analysis, you can additionally clog the sewer pipe with construction debris.
If, nevertheless, a decision is made to remove the toilet bowl with your own hands, then it is important to adhere to the following algorithm:
- Blocking the water supply to the tank.
- Dismantling the barrel and unscrewing the nuts that fix the base of the product.
- Next, you need to slightly move the toilet, opening the drain.
- Using a plumbing cable, carefully clean the knee and part of the sewer pipe.
Cleaning the toilet is a rather unpleasant task that can take a lot of effort, nerves, time and money.
Tips from professional plumbers to help prevent blockages:
- Do not dispose of food waste down the toilet, no matter how small.
- Do not rinse toilet paper, and even more so other hygiene products. There were cases when even a baby diaper was pulled out of the riser.
- Clean the toilet bowl with baking soda or a commercial product every month for preventive purposes.
Blitz tips:
- If there is a blockage, first try to remember what could be the cause:
- Folk recipes with soda or citric acid will cope with food waste.
- Multi-layered paper or the contents of the vacuum cleaner container will dissolve special chemicals.
- Dense solid waste, such as clay, sand, can only be overcome by a cable.
- For such situations, at home it is better to have a mandatory set of soda, a plunger, a cable, as well as several pairs of long rubber gloves.
housetronic.ru
How to clear a blockage in the toilet: looking for the most effective method
Digging in the toilet is not very pleasant, so we shift the decision on how to clear the blockage in the toilet to local plumbers. Despite the fact that they do an excellent job with this task, the masters still breed such incredible dirt and stench in the house that you involuntarily think about the fact that next time you need to try to take the situation into your own hands and do everything yourself. But how? I don't understand anything about this, do I? Yes, there is nothing to understand. There are only three ways to remove blockage from the toilet - two "official" and one folk. We will talk about them in this article, in which, together with the site vannaja.net, we will find out what each of these methods is and which one is better.
What to do if the toilet is clogged
How to clean a blockage in the toilet: determine the location of the blockage
First of all, you need to remember that the water from the toilet may not go away not only because of a blockage in it. In most cases, all the troubles lie in the mud plug formed in the riser itself. Before taking any measures, you need to visit the neighbors in the riser - if this situation is not only with you, then this is definitely not the case with your sewer. In such a situation, you need to decide where this plug is located and definitely call the plumbers from the Housing Office.
Determining the location of the blockage is not so difficult - going down from the top floor to the bottom, we are looking for an apartment in which everything is fine with this matter. As soon as one comes across, we can conclude that the blockage is between this and the upper floor. If the inhabitants of the first floor suffer from this misfortune, then the blockage is located in the basement on a lounger. And this is also the diocese of plumbers from the Housing Office.
If only you have problems with draining water, then we can safely say that the blockage is in the toilet bowl or on the lounger of your apartment wiring. Only now you can ask a specific solution to the question, what to do if the toilet is clogged?
How to find a blockage and clean the toilet
Clearing blockages with traditional tools: two ways
In most cases, the question of how to clean the toilet is solved by plumbers using a cable or plunger. These technologies are quite simple, but have their drawbacks.
In my opinion, the most correct solution to the question of what to do if the toilet is clogged is to use one proven folk method that helps to eliminate any blockages. We will talk about it further.
How to clear a clogged toilet with a plastic bottle
The solution to the question of how to clean the toilet if it is clogged is probably lying quietly or standing with a supply of water somewhere near the trash can. Yes, you heard right, we are talking about a plastic bottle of beer or soda with a volume of 2 liters - it is she who is able to quickly and efficiently solve the issue of cleaning the toilet. The principle of operation of such a home-made device is based on the laws of hydrodynamics. To be more precise, there is such a thing as water hammer, which will have to be artificially created in the liquid that has stagnated in your toilet. How to do it? It's very simple - you just have to get a little dirty, so it's better to stock up on a pair of rubber gloves.
We take a two-liter plastic bottle and cut off its bottom with a sharp knife - we do not throw away the cap from the neck, but rather twist it tighter. Now we insert the bottle with the cut bottom into the toilet bowl and slowly press it into the water until we feel air resistance inside the bottle. Did you feel? Now we sharply press the bottle into the toilet with all our strength and immediately pull it out. The pressure resulting from such an action is very large - it pushes the blockage into the sewer.
As a rule, more than two or three such water hammers are not required to break through the blockage. Here you need to understand the principle of this method and not be afraid to apply it. In most cases, a person who is aware of this method of eliminating blockages gets everything right the first time. So if the toilet is clogged and the water is standing, you should not immediately run to the housing office - it's better to go to the nearest store for soda.
Before resorting to using one of all of the above methods, excess water from the toilet must be scooped out - it should remain as in a normal situation. Otherwise, you will not be able to use either the plunger, or the cable, or the plastic bottle.
The video shows another way to clean the toilet with your own hands.
Cleaning the toilet with household chemicals
Recently, the so-called household chemicals, which are a weak solution of acids, have become widespread. It is actively used to eliminate sewer blockages for the reason that it allows you to cope with most types of blockage without getting your hands dirty. It should be understood that it all depends on what your toilet is clogged with - if by some miracle socks ended up there, then even a strong acid is unlikely to help you, especially if other dirt has already stuck on top of the rags.
How to clean the toilet with household chemicals photo
If you have already decided to test the products of modern chemistry in practice, then it is better to use pure acid, for example, hydrochloric acid. It can be purchased in modern construction markets. You need to be extremely careful with it and use all kinds of protective equipment - you need to protect not only your hands and exposed skin, but also your eyes, and especially the respiratory tract. The water from the toilet should be drained to the maximum - only after that it will be possible to pour about a liter of hydrochloric acid into the toilet and immediately leave the room. The reaction will take place within 30-60 minutes. After this time, the acid will corrode everything there, and the toilet bowl must be rinsed with plenty of water and cleaned with modern disinfectants. You need to be prepared for the fact that all connections in the sewer pipes into which acid penetrates will have to be additionally sealed. I believe that this method should be used only in extreme cases, when no other methods help.
That's all that can be said about how to clear a blockage in the toilet. In my opinion, it is necessary to act in more traditional, and most importantly, safer ways. I completely forgot to mention another old grandfather method that has been used since the days of the USSR. In the toilet, after scooping up water, a pack, or even two soda, is poured. After its dissolution, an active alkaline environment is created, which quite simply copes with some types of blockages.
← Bath drain: varieties of siphons and their features, the principle of self-installation Which toilet to choose: varieties and their design features →
www.vannaja.net
How to clean a clogged toilet?
In houses and apartments, problems periodically arise with the sewer system. It becomes clogged. There are plenty of reasons for this. But in order to eliminate possible consequences, you need to know how to quickly clear the blockage. There are recommendations and advice from the masters, without which it is impossible to cope with stagnation.
signs
How to clean the toilet? If you do not make manipulations to fix the problem in time, a breakdown may occur. Everyone has the right to call the master, but he does not always arrive promptly, and it is quite possible to cope with his own hands. There are elementary clues that will help you understand that a blockage has formed in the plumbing:
Any sign indicates that there is stagnation and should be urgently removed.
Why is this happening?
It is believed that over time any toilet can become clogged. And in order to prevent serious problems, it is worth periodically paying attention to this. How to clean the toilet at home? Actions will be effective only if you know why the traffic jam occurred. The reasons may be as follows:
- Violations in the process of installation work. Not everyone can know how to create a drain system, so at the installation level, this must be remembered. If the angle of inclination is small, then flushing is poor. Waste begins to be fixed in some place, creating a tight plug.
- Unsuitable waste. Often, residents in the toilet wash off the remnants of food. This includes a lot - potatoes, cereals, peelings from fruits and vegetables, etc. As a result, stagnation is formed, which accumulates in the system.
- Garbage. This is not uncommon. They wash away a lot - glass, paper, bags, etc. The toilet is not a garbage can, and you should not do this.
- When there are animals in the house, the owners do not complicate their lives and flush the used filler for the tray into the toilet. And in the composition - a special clay that can retain moisture inside. When the lumps are in a humid space, they swell and stick together. As a result, a dense plug is formed.
These are common causes of blockage. But how to clean the toilet at home? After finding out the reason, the cleaning process itself begins.
Cork elimination technique
There are plenty of ways to clean the toilet. The method is chosen taking into account the occurrence of the problem. For an apartment or house, you can choose any option - mechanical or chemical. When the cork is too big, the chemistry will be powerless. Small stagnations are removed without the use of mechanical action. Having assessed the current situation, having studied the scale of the traffic jam and the reason that created it, they choose the method of work. Anyone can handle it on their own, if you follow the basic rules.
mechanical method
This option is common, because it is the most effective. It is not necessary to call a plumber to do this. With a margin of time and a tool, you will remove the blockage in a short time. You just need to have a device in the apartment. There are several of them:
These are two simple ways that do not require large investments and do not have the complexity of implementation. Even a person without experience will be able to clean the drain structure. Sometimes it happens that even such methods do not help to achieve the desired effect. In this case, you will have to call the masters, although they can apply this. What else can help clear the blockage?
Chemical substances
Here's how to clean a toilet bowl. There are many different products on the market. After hitting the pipe, they struggle with the problem. They are available in different states - liquid and bulk. Do not worry - the drain system does not deteriorate even with prolonged contact. Below we will consider which means are effective.
Vinegar and soda
These components are available in the kitchen of any apartment and house. They are great to help solve the problem. If there are no such funds, then you can buy them at any store. You need to buy one pack of soda and a bottle of vinegar (70%). How to clean a clogged toilet at home with these products? You need to remove the water if there is too much of it. After that, soda is poured in and pushed with a stick as deep as possible. Then 200 grams of vinegar essence is poured. Hot water is used to speed up the reaction. According to people, such a tool helps after 20 minutes. But be careful not to burn the skin.
Pipe cleaning chemicals
The basis is chemical elements that can destroy fat, salts and other components. On the shelves of stores there are both domestic and foreign manufacturers. But first you need to read the instructions and understand for which pipes this or that product can be used. In addition to blockage, an unpleasant odor is also removed. How does such a method work? According to the instructions, the agent is selected and the required amount is poured into the pipe. Next - hot water in the right proportion. After such manipulations, you can not use the toilet for at least one hour. When time passes, the toilet is flushed with hot water or from a drain barrel.
The process of fixing the problem itself will not be difficult. Everyone knows that it is easier to prevent a clog than to clean it up. In a house or apartment, it is worth monitoring the drain system, otherwise a serious emergency may occur one day.
Preventive actions
How to clear a blockage in the toilet? In order not to look for an answer to this question, it is worth observing the elementary rules for using the drain system. There will be no difficulty in this:
- The toilet should not become a trash can. After all, any waste - food or household - sooner or later will create a solid cork.
- Sometimes (once a week) it is worth applying chemicals to avoid serious blockage.
- To avoid such problems, you need to periodically flush the system with a bucket of hot water.
- It happens that there is a fan riser in the room. His work will be effective with constant serviceability. If the riser does not work, a blockage may form.
Elementary manipulations help to remove the blockage in the sewer pipe quickly, without involving the master. But there is no need to make mistakes - you should fully control the work.
fb.ru
How to clean the toilet at home
If you come to visit, you always briefly evaluate the cleanliness of the room, the design of the apartment. However, if the hallway and living room can leave a good impression, then after visiting the bathroom, your attitude may change radically.
Every person has ever faced a situation when it was urgently necessary to bring the plumbing into proper condition for the arrival of guests or eliminate the blockage in the pipe. Usually, for such minor work, they do not call a plumber, but try to solve problems on their own. So that after eliminating blockages and cleaning the toilet, you do not have to change the plumbing itself, pay attention to these recommendations.
Prevention and cleaning of the surface of the toilet bowl
Causes of blockages in sewer pipes:
- When installing the toilet, the installation rules were not followed. The master set the wrong slope of the pipe, as a result of which the drain is difficult;
- Getting into the sewer pipes of a foreign body;
- Wear of pipes and the occurrence of build-ups as a result of long operation.
- Improper plumbing maintenance.
To solve the problems that arise with the operation of the toilet, there are two ways out:
- External cleaning of the surface of the toilet bowl in order to disinfect and give an aesthetic appearance;
- Elimination of blockages in the drain pipe. This problem mainly becomes relevant with poor drainage of water from the tank.
The market is overflowing with plumbing care products. However, they often contain dangerous acids and alkalis in their composition, which, upon contact with the skin, can cause severe burns. And the vapors formed after application are harmful and have a strong specific smell. In addition, cleaning with these products should be done regularly. Folk remedies are not inferior in quality of cleaning, moreover, they are absolutely safe for humans and cheaper in price terms.
Well helps in getting rid of urinary stone and rust ordinary table vinegar. It will be more effective to use a 70% solution of acetic acid. Vinegar should be heated in a saucepan and carefully poured into the toilet. Then add soda and a little iodine. Leave the resulting mixture overnight or for several hours. After we clean the surface with a non-metallic brush and rinse.
Also an excellent folk remedy in the fight against plaque on the toilet is citric acid. You need to pour a few packets of acid into the toilet and close the lid. After a few hours, as well as after using vinegar, wipe the surface and rinse with running water.
A more radical way to achieve an aesthetic look is technical oxalic acid. You can buy it at a pharmacy. Use very carefully, wearing gloves, as this substance is very toxic. Just soak a cloth in water and sprinkle some powder on it. Then wipe the toilet bowl with the resulting mixture. Then wait one hour and wash off with water.
Ways to clean the toilet
Cleaning folk remedies
To overcome a small blockage in the pipe, ordinary baking soda will help. You need to take half a pack of soda and dissolve in warm water. After the resulting solution is poured into the toilet. Thoroughly mix the water inside the knee with a brush. Wait a few hours or leave the solution overnight. Then drain the water from the tank. This procedure will help in eliminating a small blockage in the sewer pipe, however, for solving larger problems, you should pay attention to chemicals.
Cleaning with chemicals
Available drain cleaners contain hazardous chemicals and should be used with the utmost care. Be sure to wear rubber gloves, and try to protect your airways with a mask, as fumes from acids can harm your airways. Avoid contact with eyes and mucous membranes. Do not use two or more products at the same time, mixing substances can give unpredictable results. To prevent the occurrence of major blockages, it is recommended to use these funds at least 2-3 times a month.
Cleaning with a plunger
The process of cleaning sewer blockages is carried out by creating pressure drops in the system, as a result of which the blockage is eliminated.
The scheme for cleaning with a plunger is as follows:
- Fill the toilet with water to such a level that it completely covers the plunger;
- Tightly cover the drain hole with a plunger socket and press it;
- Make several sharp movements up and down and remove the plunger from the hole;
- Repeat these steps several times until the blockage is cleared.
Cleaning the drain pipe with a cable
The cleaning cable is a hollow tube equipped with a handle, with a spiral wire at the end. The end of the cable is inserted into the knee of the toilet until it stops, after which rotational movements are carried out with the handle. To eliminate the blockage, you need to carry out these steps several times.
Elimination of blockage "doll"
A device called a "doll" is a fabric bag filled with sand. To remove the blockage using this device, you need to firmly attach the "doll" to a strong cable or rope, place it in the knee of the toilet and flush the water from the drain tank. The “doll”, guided by the flow of water, will push through the blockage. Then remove the bag from the pipe and drain the water again.
After clearing the blockage using any of these methods, flush a few liters of hot water down the toilet. Perform preventive pipe cleaning on a quarterly basis to keep your sewer system in good condition.
We hope that the measures to eliminate blockages and clean the plumbing in the above ways will help you carry out repairs yourself at no extra cost.
Video
positroika-doma.ru
How to clean the toilet from the stone with your own hands
In good conscientious owners, plumbing always shines with cleanliness. However, sometimes, after prolonged use and rare preventive cleaning, limescale and urinary stones begin to form under the rim and on the walls of the toilet bowl. This problem is not the most pleasant, but solvable. Consider how to deal with pollution and what to do if you "inherited" from the old owners of housing got a toilet bowl with a stone.
We are looking for the cause of the appearance
In order to skillfully solve the problem, it is worth familiarizing yourself with its root causes. What is limescale? These are deposits of minerals found in the water you use to flush down the toilet. These minerals are present both in river water and in well water. Thus, the more often the water is flushed, the more the existing problem is exacerbated.
You can not only remove old plaque with your own hands, but also prevent its occurrence. In especially advanced cases, plaque can cause clogging of the hole (or holes) from which water is supplied to clean the inside of the toilet bowl.
Urinary stone is a phenomenon that testifies to the laziness of the owners, who forget to flush the water in the toilet after themselves. Drops of urine dry up on the walls and lead to the appearance of very ugly stains, and subsequently - the appearance of urinary stones. It is possible to clean them, but it is much better to prevent them by timely sanitizing and cleaning plumbing.
On the rough surface of plumbing, plaque forms much faster. Therefore, sometimes it makes sense to purchase new porcelain sanitary ware.
How to clean the toilet from the stone folk methods
If your toilet is so "overgrown" that the brush no longer saves, and you and your guests are simply unpleasant to use the toilet because of disgust, it is worth arming yourself with the knowledge accumulated by many previous generations.
Folk methods can be applied in private homes with a local sewer system (septic tank) and plastic pipelines.
Attention! As part of safety precautions, the respiratory organs and skin of the hands should be protected from contact with cleaning agents and their vapors. Use rubber gloves and a respirator. Protect your eyes from accidental splashes.
Strong chemistry in the fight against mineral deposits
Attention! Before using this or that means, it is necessary to familiarize yourself with the factory instructions for use, where the amount of the drug for a single use and the duration of action are prescribed. It is necessary to protect the organs of vision, breathing and skin of the hands from accidental contact with acids and alkalis. Most of the products are unsuitable for cleaning toilets in houses with plastic piping and local treatment plants (septic tanks).
Liquid acids and alkalis
- Orthophosphoric acid (solution 5-7%). This acid can be used to clean not only the stone from the toilet bowl, but also the internal parts of the drain tank from corrosion that has appeared. To use, pour about 100 g of acid solution into the tank and toilet bowl, rinse with water after 10-15 minutes and clean the surfaces with a brush (brush). Acid is not expensive, it does not affect enamel, rubber and plastic. Use with rubber gloves on your hands.
- Hydrochloric acid solution 33% is a very strong toilet cleaner, but requires extreme caution when using (keep your hands and do not inhale the fumes). It is enough to wipe the walls and pour about one glass of acid into the toilet to quickly get rid of pollution. Action time - 15 minutes. Close the toilet lid after application. Not suitable for use in toilets connected to plastic pipes.
- Liquid battery electrolyte. Usually used by car owners, but this super powerful mixture of sulfuric acid and distilled water can rid your toilet of even heavy limescale. The method of application and safety precautions are similar to hydrochloric acid. Not suitable for frequent use.
- Chlorine. Many cleaning products are produced on the basis of chlorine, including the domestic "Belizna" and the imported "Domestos". However, chlorine-containing preparations are extremely detrimental to health, therefore, despite their effectiveness, their use is not recommended. How to use: apply to the surface, after 30-60 minutes clean the toilet with a brush and rinse everything with water. Some "specialists" pour "Whiteness" into the toilet bowl.
It is also effective, but quite dangerous (including for the health of the female reproductive system).
- Popular cleaning products. In stores, you can find many liquid (creams, gels, solutions) products designed specifically to combat chronic lime deposits and urinary stones. Such preparations are applied for 30-60 minutes under the rim of the toilet, after which the surface is cleaned with a brush. If necessary, the procedure is repeated several times. Products of popular brands: Cillit and "Toilet Duck" (drugs based on hydrochloric acid).
Abrasive powders
All commercially available abrasive cleaners do a good job of solving the problem of cleaning the toilet. However, tiny granules often leave micro-scratches on the surface of the sanitary ware, as a result of which limescale will reappear after a short period of time.
If there is no alternative to using abrasives, then they are used as follows: water is pumped out of the toilet bowl, after which a layer of powder is poured. Then you can leave the agent for exposure or immediately start cleaning with a brush / brush / hard washcloth. It is necessary to rub until the plaque completely disappears. The procedure is quite unpleasant and tedious.
The cistern tablets are not only a plaque remover, but also great for preventing urinary stones. In addition, cistern products have a pleasant aroma, disinfect and disinfect the surface of sanitary ware, and prolong its service life. It is enough to purchase a package of the product you like and put 1 tablet inside the tank. As soon as the tablet begins to dissolve, the water will turn into some shade. The disappearance of the coloring pigment in the water will indicate the need to add a new tablet to the tank.
In addition to preventive cleaning and emergency methods of dealing with a stone in the toilet, it is recommended to adjust the water supply in the tank. After all, excess water for flushing is not only financially unprofitable, but is also one of the root causes of the appearance of lime deposits. The easiest way to reduce the volume of the tank is to place 1-2 plastic water bottles in it. This will reduce consumption by 2-3 liters with each use. And in the case of purchasing new plumbing, choose a tank with a double button and a water-saving mode.
Video - How to clean the toilet from a stone
kanalizaciyaseptik.ru
How to clean the toilet and clear the blockage yourself
The sewer system can fail sooner or later! And it doesn’t matter if we are talking about a private household or an apartment in a high-rise building. Especially unpleasant emotions are caused by a situation when a blockage appears in the bathroom and the owner has to urgently resolve the issue and look for a way to clean the toilet. It is very important to understand that clogging of this plumbing element can cause clogging of other parts of the sewer pipeline in the house. But, as you know, there are no hopeless situations, and, despite the fact that the maintenance of the plumbing and sewer system is a whole science, there are many methods for cleaning the toilet bowl.
Note! The most efficient and effective way to clear a clogged toilet is to call a plumber. It may not be cheap, but a professional will do all the work, and the question of how to eliminate a blockage in the toilet will absolutely not bother you.
First you need to try to find out the cause of the blockage. It is absolutely clear here that in the process of proper operation of the toilet, there can be no problems with it in principle. Therefore, most likely a blockage indicates the presence of a third-party bulk object in the toilet bowl (usually rags, paper, bags). It is their extraction from the sewer system that will solve all problems. This situation is especially typical for housing in apartment buildings, and residents of the lower floors are especially familiar with it.
Cleaning with a plunger
Almost everyone is “friends” with this item: they know it by sight and are familiar with its functional purpose. A plunger will quite effectively cope with loosening a slight blockage. Ideally, a plunger with a cone-shaped nozzle should be stored in the pantry specifically for the toilet.
Cleaning the toilet with a plunger is a classic of the genre
Before you start pumping the drain hole, the toilet is filled with water. Then the plunger is installed on the hole and several successive clicks are made on its wooden handle. Then the device is abruptly removed. It is these simple movements that contribute to loosening and blockage, and very soon the water will begin to freely go where it should.
"Doll" and rope
If the use of a plunger did not bring the expected result, then it means that you will have to take measures to clean the hydraulic valve itself. Specifically, you need to do the following:
Option number 1. Make a puppet. That is, fill a rag bag with sand and tie a rope to it. "Doll" lower into the toilet and press the flush lever. At the same time, lower the rope of the "doll" so that the flow of water draws it into the toilet funnel. Such a “doll”, heavy enough to break through the blockage in the water seal.
Option number 2. Use a special flexible cable, which is actually a rigid hollow axis with a rotating handle. The end of the axle is equipped with a long spiral process of thick wire attached to the cable with a flexible tube. It is thanks to this tube that the cable becomes more mobile and protects the inner surface of the plumbing element from mechanical damage. The spiral end of the cable is lowered all the way into the toilet neck. The handle rotates clockwise and the cable is slowly pushed further into the water seal. Such actions should destroy the blockage. And to complete this method of cleaning the toilet, you need to flush the system with hot water.
Cleaning the toilet with a rope is very effective
Or a plastic bottle?
Sometimes you can solve a non-standard situation with a simple plastic bottle. It is necessary to cut off the bottom in it and the homemade plunger is ready for use. When working with a bottle, all movements must be performed sharply. Just as in the case of a conventional plunger, the toilet is filled with water, the bottle is lowered with the cut end inward and sharply pressed on it. Then the bottle is also abruptly removed. Now you know how to clean the toilet with a bottle.
By the way: such a seemingly primitive device is actually quite effective and is in the spare arsenal of almost every plumber.
Chemicals
Special household chemicals aimed at high-quality elimination of blockages in the toilet are also very popular among consumers:
- powders;
- liquids;
- granules;
- sprays.
In order to determine in a particular situation which particular remedy for clogging the toilet bowl will be most appropriate, it is necessary to understand the nature of the blockage. Therefore, if you find trouble, you should not panic, but you need to assess the situation and make the right informed decision.
Attention! If a way out of the situation is not immediately found, then you should seek advice from the global network. By asking a query like: blockage in the toilet - what to do, you can quickly find qualified advice.
Modern toilet cleaning tools are extremely effective
folk recipe
Since the "Soviet" times, it has been popular as a means to eliminate blockages in the sewer, including ordinary soda in the toilet. Half a pack of soda is poured into the toilet and dissolved in water. Thus, an active alkali is created, which in some situations can correct the situation. However, with difficult blockages with only one soda, the situation cannot be solved.
DIY ceramic heater